Abstract: A new low-voltage floating gate MOSFET (FGMOS)
based squarer using square law characteristic of the FGMOS is
proposed in this paper. The major advantages of the squarer are simplicity,
rail-to-rail input dynamic range, low total harmonic distortion,
and low power consumption. The proposed circuit is biased without
body effect. The circuit is designed and simulated using SPICE in
0.25μm CMOS technology. The squarer is operated at the supply
voltages of ±0.75V . The total harmonic distortion (THD) for the
input signal 0.75Vpp at 25 KHz, and maximum power consumption
were found to be less than 1% and 319μW respectively.
Abstract: In this paper, a new approach for design of a fully
differential second order current mode continuous-time sigma-delta
modulator is presented. For circuit implementation, square root
domain (SRD) translinear loop based on floating-gate MOS
transistors that operate in saturation region is employed. The
modulator features, low supply voltage, low power consumption
(8mW) and high dynamic range (55dB). Simulation results confirm
that this design is suitable for data converters.
Abstract: The energy consumption and delay in read/write
operation of conventional SRAM is investigated analytically as well
as by simulation. Explicit analytical expressions for the energy
consumption and delay in read and write operation as a function of
device parameters and supply voltage are derived. The expressions are
useful in predicting the effect of parameter changes on the energy
consumption and speed as well as in optimizing the design of
conventional SRAM. HSPICE simulation in standard 0.25μm CMOS
technology confirms precision of analytical expressions derived from
this paper.
Abstract: As known, the guard wires of overhead high voltage
are usually grounded through the grounding systems of support and
of the terminal stations. They do affect the zero sequence impedance
value of the line, Z0, which is generally, calculated assuming that the
wires guard are at ground potential. In this way it is not considered
the effect of the resistances of earth of supports and stations. In this
work is formed a formula for the calculation of Z0 which takes
account of said resistances. Is also proposed a method of calculating
the impedance zero sequence overhead lines in which, in various
sections or spans, the guard wires are connected to the supports, or
isolated from them, or are absent. Parametric analysis is given for
lines 220 kV and 400 kV, which shows the extent of the errors made
with traditional methods of calculation.
Abstract: In this paper, we analyze the effect of noise in a single- ended input differential amplifier working at high frequencies. Both extrinsic and intrinsic noise are analyzed using time domain method employing techniques from stochastic calculus. Stochastic differential equations are used to obtain autocorrelation functions of the output noise voltage and other solution statistics like mean and variance. The analysis leads to important design implications and suggests changes in the device parameters for improved noise characteristics of the differential amplifier.
Abstract: Design of Converter transformer insulation is a major
challenge. The insulation of these transformers is stressed by both
AC and DC voltages. Particle contamination is one of the major
problems in insulation structures, as they generate partial discharges
leading it to major failure of insulation. Similarly corona discharges
occur in transformer insulation. This partial discharge due to particle
movement / corona formation in insulation structure under different
voltage wave shapes, are different. In the present study, UHF
technique is adopted to understand the discharge activity and could
be realized that the characteristics of UHF signal generated under
low and high fields are different. In the case of corona generated
signal, the frequency content of the UHF sensor output lies in the
range 0.3-1.2 GHz and is not much varied except for its increase in
magnitude of discharge with the increase in applied voltage. It is
realized that the current signal injected due to partial
discharges/corona is about 4ns duration measured for first one half
cycle. Wavelet technique is adopted in the present study. It allows
one to identify the frequency content present in the signal at different
instant of time. The STD-MRA analysis helps one to identify the
frequency band in which the energy content of the UHF signal is
maximum.
Abstract: The demand on High voltage (HV) infrastructures is growing due to the corresponding growth in industries and population. New or upgraded HV infrastructure has safety implications since Transmission mains usually occupy the same easement in the vicinity of neighbouring residents. Transmission mains consist of underground (UG) and overhead (OH) sections and the transition between the UG and OH section is known as the UGOH pole. The existence of two transmission mains in the same easement can dictate to resort to more complicated earthing design in order to mitigate the effect of AC interference, and in some cases it can also necessitates completing a Split Study of the system. This paper provides an overview of the AC interference, Split Study and the earthing of an underground feeder including the UGOH pole .In addition, this paper discusses the use of different link boxes on the UG feeder and presents a case study that represent a clear example of the Ac interference and Split factor. Finally, a few recommendations are provided to achieve a safety zone in the area beyond the boundary of the HV system.
Abstract: This paper presents a model for analysis the induced voltage of transmission lines (energized) acting on neighboring distribution lines (de-energized). From environmental restrictions, 22 kV distribution lines need to be installed under 115 kV transmission lines. With the installation of the two parallel circuits like this, they make the induced voltage which can cause harm to operators. This work was performed with the ATP-EMTP modeling to analyze such phenomenon before field testing. Simulation results are used to find solutions to prevent danger to operators who are on the pole.
Abstract: This research aimed to develop plasma system used in air conditioners. This developed plasma system could be installed in the air conditioners - all split type. The quality of air could be improved to be equal to present plasma system. Development processes were as follows: 1) to study the plasma system used in the air conditioners, 2) to design a plasma generator, 3) to develop the plasma generator, and 4) to test its performance in many types of the air conditioners. This plasma system was developed by AC high voltage – 14 kv with a frequency of 50 kHz. Carbon was a conductor to generate arc in air purifier system. The research was tested by installing the plasma generator in the air conditioners - wall type. Whereas, there were 3 types of installations: air flow out, air flow in, and room center. The result of the plasma generator installed in the air conditioners, split type, revealed that the air flow out installation provided the highest average of o-zone at 223 mg/h. This type of installation provided the highest efficiency of air quality improvement. Moreover, the air flow in installation and the room center installation provided the average of the o-zone at 163 mg/h and 64 mg/h, respectively.
Abstract: This paper presents design and implements the
T-DOF PI controller design for a speed control of induction motor.
The voltage source inverter type space vector pulse width modulation
technique is used the drive system. This scheme leads to be able to
adjust the speed of the motor by control the frequency and amplitude
of the input voltage. The ratio of input stator voltage to frequency
should be kept constant. The T-DOF PI controller design by root
locus technique is also introduced to the system for regulates and
tracking speed response. The experimental results in testing the 120
watt induction motor from no-load condition to rated condition show
the effectiveness of the proposed control scheme.
Abstract: Noise level has critical effects on the diagnostic
performance of signal-averaged electrocardiogram (SAECG), because
the true starting and end points of QRS complex would be masked by
the residual noise and sensitive to the noise level. Several studies and
commercial machines have used a fixed number of heart beats
(typically between 200 to 600 beats) or set a predefined noise level
(typically between 0.3 to 1.0 μV) in each X, Y and Z lead to perform
SAECG analysis. However different criteria or methods used to
perform SAECG would cause the discrepancies of the noise levels
among study subjects. According to the recommendations of 1991
ESC, AHA and ACC Task Force Consensus Document for the use of
SAECG, the determinations of onset and offset are related closely to
the mean and standard deviation of noise sample. Hence this study
would try to perform SAECG using consistent root-mean-square
(RMS) noise levels among study subjects and analyze the noise level
effects on SAECG. This study would also evaluate the differences
between normal subjects and chronic renal failure (CRF) patients in
the time-domain SAECG parameters.
The study subjects were composed of 50 normal Taiwanese and 20
CRF patients. During the signal-averaged processing, different RMS
noise levels were adjusted to evaluate their effects on three time
domain parameters (1) filtered total QRS duration (fQRSD), (2) RMS
voltage of the last QRS 40 ms (RMS40), and (3) duration of the low
amplitude signals below 40 μV (LAS40). The study results
demonstrated that the reduction of RMS noise level can increase
fQRSD and LAS40 and decrease the RMS40, and can further increase
the differences of fQRSD and RMS40 between normal subjects and
CRF patients. The SAECG may also become abnormal due to the
reduction of RMS noise level. In conclusion, it is essential to establish
diagnostic criteria of SAECG using consistent RMS noise levels for
the reduction of the noise level effects.
Abstract: Induction machine models used for steady-state and
transient analysis require machine parameters that are usually
considered design parameters or data. The knowledge of induction
machine parameters is very important for Indirect Field Oriented
Control (IFOC). A mismatched set of parameters will degrade the
response of speed and torque control. This paper presents an
improvement approach on rotor time constant adaptation in IFOC for
Induction Machines (IM). Our approach tends to improve the
estimation accuracy of the fundamental model for flux estimation.
Based on the reduced order of the IM model, the rotor fluxes and
rotor time constant are estimated using only the stator currents and
voltages. This reduced order model offers many advantages for real
time identification parameters of the IM.
Abstract: The breakdown strength characteristic of Low Density
Polyethylene films (LDPE) under DC voltage application and the
effect of water absorption have been studied. Mainly, our experiment
was investigated under two conditions; dry and heavy water
absorption. Under DC ramp voltage, the result found that the
breakdown strength under heavy water absorption has a lower value
than dry condition. In order to clarify the effect, the temperature rise of
film was observed using non contact thermograph until the occurrence
of the electrical breakdown and the conduction current of the sample
was also measured in correlation with the thermograph measurement.
From the observations, it was shown that under the heavy water
absorption, the hot spot in the samples appeared at lower voltage. At
the same voltage the temperature of the hot spot and conduction
current was higher than that under the dry condition. The measurement
result has a good correlation between the existence of a critical field
for conduction current and thermograph observation. In case of the
heavy water absorption, the occurrence of the threshold field was
earlier than the dry condition as result lead to higher of conduction
current and the temperature rise appears after threshold field was
significantly increased in increasing of field. The higher temperature
rise was caused by the higher current conduction as the result the
insulation leads to breakdown to the lower field application.
Abstract: In this paper, we apply the PQ theory with shunt active power filter in an unbalanced and distorted power system voltage to compensate the perturbations generated by non linear load. The power factor is also improved in the current source. The PLL system is used to extract the fundamental component of the even sequence under conditions mentioned of the power system voltage.
Abstract: A generalized unified power quality conditioner
(GUPQC) by using three single-phase three-level voltage source
converters (VSCs) connected back-to-back through a common dc
link is proposed in this paper as a new custom power device for a
three-feeder distribution system. One of the converters is connected
in shunt with one feeder for mitigation of current harmonics and
reactive power compensation, while the other two VSCs are
connected in series with the other two feeders to maintain the load
voltage sinusoidal and at constant level. A new control scheme based
on synchronous reference frame is proposed for series converters.
The simulation analysis on compensation performance of GUPQC
based on PSCAD/EMTDC is reported.
Abstract: This paper proposes a set of quasi-static mathematical
model of magnetic fields caused by high voltage conductors of
distribution transformer by using a set of second-order partial
differential equation. The modification for complex magnetic field
analysis and time-harmonic simulation are also utilized. In this
research, transformers were study in both balanced and unbalanced
loading conditions. Computer-based simulation utilizing the threedimensional
finite element method (3-D FEM) is exploited as a tool
for visualizing magnetic fields distribution volume a distribution
transformer. Finite Element Method (FEM) is one among popular
numerical methods that is able to handle problem complexity in
various forms. At present, the FEM has been widely applied in most
engineering fields. Even for problems of magnetic field distribution,
the FEM is able to estimate solutions of Maxwell-s equations
governing the power transmission systems. The computer simulation
based on the use of the FEM has been developed in MATLAB
programming environment.
Abstract: The interline power flow controller (IPFC) is one of
the latest generation flexible AC transmission systems (FACTS)
controller used to control power flows of multiple transmission lines.
This paper presents a mathematical model of IPFC, termed as power
injection model (PIM). This model is incorporated in Newton-
Raphson (NR) power flow algorithm to study the power flow control
in transmission lines in which IPFC is placed. A program in
MATLAB has been written in order to extend conventional NR
algorithm based on this model. Numerical results are carried out on a
standard 2 machine 5 bus system. The results without and with IPFC
are compared in terms of voltages, active and reactive power flows to
demonstrate the performance of the IPFC model.
Abstract: In this paper, we propose a novel metal oxide
semiconductor field effect transistor with L-shaped channel structure
(LMOS), and several type of L-shaped structures are also designed,
studied and compared with the conventional MOSFET device for the
same average gate length (Lavg). The proposed device electrical
characteristics are analyzed and evaluated by three dimension (3-D)
ISE-TCAD simulator. It can be confirmed that the LMOS devices
have higher on-state drain current and both lower drain-induced
barrier lowering (DIBL) and subthreshold swing (S.S.) than its
conventional counterpart has. In addition, the transconductance and
voltage gain properties of the LMOS are also improved.
Abstract: This paper presents the DC voltage control design of D-STATCOM when the D-STATCOM is used for load voltage regulation. Although, the DC voltage can be controlled by active current of the D-STATCOM, reactive current still affects the DC voltage. To eliminate this effect, the control strategy with elimination effect of the reactive current is proposed and the results of the control with and without the elimination the effect of the reactive current are compared. For obtaining the proportional and integral gains of the PI controllers, the symmetrical optimum and genetic algorithms methods are applied. The stability margin of these methods are obtained and discussed in detail. In addition, the performance of the DC voltage control based on symmetrical optimum and genetic algorithms methods are compared. Effectiveness of the controllers designed was verified through computer simulation performed by using Power System Tool Block (PSB) in SIMULINK/MATLAB. The simulation results demonstrated that the DC voltage control proposed is effective in regulating DC voltage when the DSTATCOM is used for load voltage regulation.
Abstract: In this paper, a novel LVTSCR-based device for
electrostatic discharge (ESD) protection of integrated circuits (ICs) is
designed, fabricated and characterized. The proposed device is similar
to the conventional LVTSCR but it has an embedded PMOSFET in the
anode n-well to enhance the turn on speed, the clamping capability and
the robustness. This is possible because the embedded PMOSFET
provides the sub-path of ESD discharge current. The TLP, HBM and
MM testing are carried out to verify the ESD performance of the
proposed devices, which are fabricated in 0.35um
(Bipolar-CMOS-DMOS) BCDMOS process. The device has the
robustness of 70mA/um that is higher about 60mA/um than the
LVTSCR, approximately.