Abstract: One of the most important power quality issues is voltage flicker. Nowadays this issue also impacts the power system all over the world. The fact of the matter is that the more and the larger capacity of wind generator has been installed. Under unstable wind power situation, the variation of output current and voltage have caused trouble to voltage flicker. Hence, the major purpose of this study is to analyze the impact of wind generator on voltage flicker of power system. First of all, digital simulation and analysis are carried out based on wind generator operating under various system short circuit capacity, impedance angle, loading, and power factor of load. The simulation results have been confirmed by field measurements.
Abstract: The paper presents a space-vector pulse width modulation (SVPWM) inverter feeding a permanent-magnet synchronous motor (PMSM). The SVPWM inverter enables to feed the motor with a higher voltage with low harmonic distortions than the conventional sinusoidal PWM inverter. The control strategy of the inverter is the voltage / frequency control method, which is based on the space-vector modulation technique. The proposed PMSM drive system involving the field-oriented control scheme not only decouples the torque and flux which provides faster response but also makes the control task easy. The performance of the proposed drive is simulated. The advantages of the proposed drive are confirmed by the simulation results.
Abstract: The switching lag-time and the voltage drop across
the power devices cause serious waveform distortions and
fundamental voltage drop in pulse width-modulated inverter output.
These phenomenons are conspicuous when both the output frequency
and voltage are low. To estimate the output voltage from the PWM
reference signal it is essential to take account of these imperfections
and to correct them. In this paper, on-line compensation method is
presented. It needs three simple blocs to add at the ideal reference
voltages. This method does not require any additional hardware
circuit and off- line experimental measurement. The paper includes
experimental results to demonstrate the validity of the proposed
method. It is applied, finally, in case of indirect vector controlled
induction machine and implemented using dSpace card.
Abstract: At present, it is very common to find renewable
energy resources, especially wind power, connected to distribution
systems. The impact of this wind power on voltage distribution levels
has been addressed in the literature. The majority of this works deals
with the determination of the maximum active and reactive power
that is possible to be connected on a system load bus, until the
voltage at that bus reaches the voltage collapse point. It is done by the
traditional methods of PV curves reported in many references.
Theoretical expression of maximum power limited by voltage
stability transfer through a grid is formulated using an exact
representation of distribution line with ABCD parameters. The
expression is used to plot PV curves at various power factors of a
radial system. Limited values of reactive power can be obtained. This
paper presents a method to study the relationship between the active
power and voltage (PV) at the load bus to identify the voltage
stability limit. It is a foundation to build a permitted working
operation region in complying with the voltage stability limit at the
point of common coupling (PCC) connected wind farm.
Abstract: This paper presents the effectiveness of artificial
intelligent technique to apply for pattern recognition and
classification of Partial Discharge (PD). Characteristics of PD signal
for pattern recognition and classification are computed from the
relation of the voltage phase angle, the discharge magnitude and the
repeated existing of partial discharges by using statistical and fractal
methods. The simplified fuzzy ARTMAP (SFAM) is used for pattern
recognition and classification as artificial intelligent technique. PDs
quantities, 13 parameters from statistical method and fractal method
results, are inputted to Simplified Fuzzy ARTMAP to train system
for pattern recognition and classification. The results confirm the
effectiveness of purpose technique.
Abstract: This paper deals with the effect of a power transformer’s vector group on the basic voltage sag characteristics during unbalanced faults at a meshed or radial power network. Specifically, the propagation of voltage sags through a power transformer is studied with advanced short-circuit analysis. A smart method to incorporate this effect on analytical mathematical expressions is proposed. Based on this methodology, the positive effect of transformers of certain vector groups on the mitigation of the expected number of voltage sags per year (sag frequency) at the terminals of critical industrial customers can be estimated.
Abstract: Photo-BJMOSFET (Bipolar Junction Metal-Oxide-
Semiconductor Field Effect Transistor) fabricated on SOI film was proposed. ITO film is adopted in the device as gate electrode to reduce
light absorption. Depletion region but not inversion region is formed
in film by applying gate voltage (but low reverse voltage) to achieve
high photo-to-dark-current ratio. Comparisons of photoelectriccharacteristics
executed among VGK=0V, 0.3V, 0.6V, 0.9V and 1.0V
(reverse voltage VAK is equal to 1.0V for total area of 10×10μm2). The
results indicate that the greatest improvement in photo-to-dark-current
ratio is achieved up to 2.38 at VGK=0.6V. In addition,
photo-BJMOSFET is compatible with CMOS integration due to big
input resistance
Abstract: The hard clam (meretrix lusoria) cultivated industry
has been developed vigorously for recent years in Taiwan, and
seawater quality determines the cultivated environment. The pH
concentration variation affects survival rate of meretrix lusoria
immediately. In order to monitor seawater quality, solid-state sensing
electrode of ruthenium-doped titanium dioxide (TiO2:Ru) is developed
to measure hydrogen ion concentration in different cultivated
solutions. Because the TiO2:Ru sensing electrode has high chemical
stability and superior sensing characteristics, thus it is applied as a pH
sensor. Response voltages of TiO2:Ru sensing electrode are readout by
instrument amplifier in different sample solutions. Mean sensitivity
and linearity of TiO2:Ru sensing electrode are 55.20 mV/pH and 0.999
from pH1 to pH13, respectively. We expect that the TiO2:Ru sensing
electrode can be applied to real environment measurement, therefore
we collect two sample solutions by different meretrix lusoria
cultivated ponds in the Yunlin, Taiwan. The two sample solutions are
both measured for 200 seconds after calibration of standard pH buffer
solutions (pH7, pH8 and pH 9). Mean response voltages of sample 1
and sample 2 are -178.758 mV (Standard deviation=0.427 mV) and
-180.206 mV (Standard deviation =0.399 mV), respectively. Response
voltages of the two sample solutions are between pH 8 and pH 9 which
conform to weak alkali range and suitable meretrix lusoria growth. For
long-term monitoring, drift of cultivated solutions (sample 1 and
sample 2) are 1.16 mV/hour and 1.03 mV/hour, respectively.
Abstract: Using strength Pulse Electrical Field (PEF) in food
industries is a non-thermal process that can deactivate
microorganisms and increase penetration in plant and animals tissues
without serious impact on food taste and quality. In this paper designing and fabricating of a PEF generator has been presented. Pulse generation methods have been surveyed and the best of them
selected. The equipment by controller set can generate square pulse with adjustable parameters such as amplitude 1-5kV, frequency 0.1-10Hz, pulse width 10-100s, and duty cycle 0-100%. Setting the number of pulses, and presenting the output voltage and current
waveforms on the oscilloscope screen are another advantages of this
equipment. Finally, some food samples were tested that yielded the satisfactory results. PEF applying had considerable effects on potato, banana and purple cabbage. It caused increase Brix factor from 0.05
to 0.15 in potato solution. It is also so effective in extraction color material from purple cabbage. In the last experiment effects of PEF
voltages on color extraction of saffron scum were surveyed (about 6% increasing yield).
Abstract: This paper presents a method for obtaining the
desired reference current for Voltage Source Converter (VSC) of the Shunt Active Power Filter (SAPF) using Synchronous Reference Frame Theory. The method relies on the performance of the Proportional-Integral (PI) controller for
obtaining the best control performance of the SAPF. To
improve the performance of the PI controller, the feedback
path to the integral term is introduced to compensate the
winding up phenomenon due to integrator. Using Reference
Frame Transformation, reference signals are transformed from
a - b - c stationery frame to 0 - d - q rotating frame.
Using the PI controller, the reference signals in the 0 - d - q rotating frame are controlled to get the desired reference signals for the Pulse Width Modulation. The synchronizer, the Phase Locked Loop (PLL) with PI filter is used for
synchronization, with much emphasis on minimizing delays. The system performance is examined with Shunt Active Power Filter simulation model.
Abstract: In our modern society electricity is vital to our health,
safety, comfort and well-being. While our daily use of electricity is
often taken for granted, public concern has arisen about potential
adverse health effects from electric and magnetic – electromagnetic –
fields (EMFs) produced by our use of electricity.
This paper aims to compare between the measured magnetic field
values and the simulated models for the indoor medium to low
voltage (MV/LV) distribution substations.
To calculate the magnetic flux density in the substations,
interactive software SUBCALC is used which is based on closed
form solution of the Biot-Savart law with 3D conductor model.
The comparison between the measured values and the simulated
models was acceptable. However there were some discrepancies, as
expected, may be due to the current variation during measurements.
Abstract: The use of synthetic retardants in polymeric insulated
cables is not uncommon in the high voltage engineering to study
electrical treeing phenomenon. However few studies on organic
materials for the same investigation have been carried. .This paper
describes the study on the effects of Oil Palm Empty Fruit Bunch
(OPEFB) microfiller on the tree initiation and propagation in silicone
rubber with different weight percentages (wt %) of filler to insulation
bulk material. The weight percentages used were 0 wt % and 1 wt %
respectively. It was found that the OPEFB retards the propagation of
the electrical treeing development. For tree inception study, the
addition of 1(wt %) OPEFB has increase the tree inception voltage of
silicone rubber. So, OPEFB is a potential retardant to the initiation
and growth of electrical treeing occurring in polymeric materials for
high voltage application. However more studies on the effects of
physical and electrical properties of OPEFB as a tree retardant
material are required.
Abstract: In this research paper, a slotted coaxial line fed cross
dipole excitation structure for short backfire antenna is proposed and
developed to achieve reconfigurable circular polarization. The cross
dipole, which is fed by the slotted coaxial line, consists of two
orthogonal dipoles. The dipoles are mounted on the outer conductor
of the coaxial line. A unique technique is developed to generate
reconfigurable circular polarization using cross dipole configuration.
The sub-reflector is supported by the feed line, thus requiring no
extra support. The antenna is developed on elliptical ground plane
with dielectric rim making antenna compact. It is demonstrated that
cross dipole excited short backfire antenna can achieve voltage
standing wave ratio (VSWR) bandwidth of 14.28% for 2:1 VSWR,
axial ratio of 0.2 dB with axial ratio (≤ 3dB) bandwidth of 2.14% and
a gain of more than 12 dBi. The experimental results for the designed
antenna structure are in close agreement with computer simulations.
Abstract: The very nonlinear nature of the generator and system
behaviour following a severe disturbance precludes the use of
classical linear control technique. In this paper, a new approach of
nonlinear control is proposed for transient and steady state stability
analysis of a synchronous generator. The control law of the generator
excitation is derived from the basis of Lyapunov stability criterion.
The overall stability of the system is shown using Lyapunov
technique. The application of the proposed controller to simulated
generator excitation control under a large sudden fault and wide
range of operating conditions demonstrates that the new control
strategy is superior to conventional automatic voltage regulator
(AVR), and show very promising results.
Abstract: Banyan networks are really attractive for serving as
the optical switching architectures due to their unique properties of
small depth and absolute signal loss uniformity. The fact has been
established that the limitations of blocking nature and the nonavailability
of proper connections due to non-rearrangeable property
can be easily ruled out using electro-optic MZI switches as basic
switching elements. Combination of the horizontal expansion and
vertical stacking of optical banyan networks is an appropriate scheme
for constructing non-blocking banyan-based optical switching
networks. The interconnected banyan switching fabrics (IBSF) have
been considered and analyzed to best serve the purpose of optical
switching with electro-optic MZI basic elements. The cross/bar state
interchange for the switches has been facilitated by appropriate
voltage switching or the by the switching of operating wavelength.
The paper is dedicated to the modification of the basic switching
element being used as well as the architecture of the switching
network.
Abstract: This paper proposes a low-voltage and low-power
fully integrated digitally tuned continuous-time channel selection
filter for WiMAX applications. A 5th-order elliptic low-pass filter is
realized in a Gm-C topology. The bandwidth of the fully differential
filter is reconfigurable from 2.5MHz to 20MHz (8x) for different
requirements in WiMAX applications. The filter is simulated in a
standard 90nm CMOS process. Simulation results show the THD
(@Vout =100mVpp) is less than -66dB. The in-band ripple of the
filter is about 0.15dB. The filter consumes 1.5mW from a supply
voltage of 0.9V.
Abstract: DC-DC converters are widely used in regulated switched mode power supplies and in DC motor drive applications. There are several sources of unwanted nonlinearity in practical power converters. In addition, their operation is characterized by switching that gives birth to a variety of nonlinear dynamics. DC-DC buck and boost converters controlled by pulse-width modulation (PWM) have been simulated. The voltage waveforms and attractors obtained from the circuit simulation have been studied. With the onset of instability, the phenomenon of subharmonic oscillations, quasi-periodicity, bifurcations, and chaos have been observed. This paper is mainly motivated by potential contributions of chaos theory in the design, analysis and control of power converters, in particular and power electronics circuits, in general.
Abstract: This paper presents a simple approach for load
flow analysis of a radial distribution network. The proposed
approach utilizes forward and backward sweep algorithm
based on Kirchoff-s current law (KCL) and Kirchoff-s voltage
law (KVL) for evaluating the node voltages iteratively. In this
approach, computation of branch current depends only on the
current injected at the neighbouring node and the current in
the adjacent branch. This approach starts from the end nodes
of sub lateral line, lateral line and main line and moves
towards the root node during branch current computation. The
node voltage evaluation begins from the root node and moves
towards the nodes located at the far end of the main, lateral
and sub lateral lines. The proposed approach has been tested
using four radial distribution systems of different size and
configuration and found to be computationally efficient.
Abstract: Application of neural networks in execution of
programmed pulse width modulation (PPWM) of a voltage source
inverter (VSI) is studied in this paper. Using the proposed method it is
possible to cancel out the desired harmonics in output of VSI in
addition to control the magnitude of fundamental harmonic,
contineously. By checking the non-trained values and a performance
index, the most appropriate neural network is proposed. It is shown
that neural networks may solve the custom difficulties of practical
utilization of PPWM such as large size of memory, complex digital
circuits and controlling the magnitude of output voltage in a discrete
manner.
Abstract: An effective approach for unbalanced three-phase
distribution power flow solutions is proposed in this paper. The
special topological characteristics of distribution networks have been
fully utilized to make the direct solution possible. Two matrices–the
bus-injection to branch-current matrix and the branch-current to busvoltage
matrix– and a simple matrix multiplication are used to
obtain power flow solutions. Due to the distinctive solution
techniques of the proposed method, the time-consuming LU
decomposition and forward/backward substitution of the Jacobian
matrix or admittance matrix required in the traditional power flow
methods are no longer necessary. Therefore, the proposed method is
robust and time-efficient. Test results demonstrate the validity of the
proposed method. The proposed method shows great potential to be
used in distribution automation applications.