Abstract: When a high DC voltage is applied to a capacitor with
strongly asymmetrical electrodes, it generates a mechanical force that
affects the whole capacitor. This phenomenon is most likely to be
caused by the motion of ions generated around the smaller of the two
electrodes and their subsequent interaction with the surrounding
medium. A method to measure this force has been devised and used.
A formula describing the force has also been derived. After
comparing the data gained through experiments with those acquired
using the theoretical formula, a difference was found above a certain
value of current. This paper also gives reasons for this difference.
Abstract: In this paper static and dynamic response of a
varactor of a micro-phase shifter to DC, step DC and AC
voltages have been studied. By presenting a mathematical
modeling Galerkin-based step by step linearization method
(SSLM) and Galerkin-based reduced order model have been
used to solve the governing static and dynamic equations,
respectively. The calculated static and dynamic pull-in
voltages have been validated by previous experimental and
theoretical results and a good agreement has been achieved.
Then the frequency response and phase diagram of the system
has been studied. It has been shown that applying the DC
voltage shifts down the phase diagram and frequency
response. Also increasing the damping ratio shifts up the
phase diagram.
Abstract: Performing High Voltage (HV) tasks with a multi craft
work force create a special set of safety circumstances. This paper
aims to present vital information relating to when it is acceptable to
use a single or a two-layer soil structure. Also it discusses the
implication of the high voltage infrastructure on the earth grid and the
safety of this implication under a single or a two-layer soil structure.
A multiple case study is investigated to show the importance of using
the right soil resistivity structure during the earthing system design.
Abstract: The purpose of this research was to analyze and compare the instability of a contact surface between Copper and Nickel an alloy cathode in vacuum, the different ratio of Copper and Copper were conducted at 1%, 2% and 4% by using the cathode spot model. The transient recovery voltage is predicted. The cathode spot region is recognized as the collisionless space charge sheath connected with singly ionized collisional plasma. It was found that the transient voltage is decreased with increasing the percentage of an amount of Nickel in cathode materials.
Abstract: Back-to-back static synchronous compensator (BtBSTATCOM) consists of two back-to-back voltage-source converters (VSC) with a common DC link in a substation. This configuration extends the capabilities of conventional STATCOM that bidirectional active power transfer from one bus to another is possible. In this paper, VSCs are designed in quasi multi-pulse form in which GTOs are triggered only once per cycle in PSCAD/EMTDC. The design details of VSCs as well as gate switching circuits and controllers are fully represented. Regulation modes of BtBSTATCOM are verified and tested on a multi-machine power system through different simulation cases. The results presented in the form of typical time responses show that practical PI controllers are almost robust and stable in case of start-up, set-point change, and line faults.
Abstract: The paper presents an optimization study based on
genetic algorithms (GA-s) for a radio-frequency applicator used in
heating dielectric band products. The weakly coupled electro-thermal
problem is analyzed using 2D-FEM. The design variables in the
optimization process are: the voltage of a supplementary “guard"
electrode and six geometric parameters of the applicator. Two
objective functions are used: temperature uniformity and total active
power absorbed by the dielectric. Both mono-objective and multiobjective
formulations are implemented in GA optimization.
Abstract: Partial Discharge measurement is a very important
means of assessing the integrity of insulation systems in a High
Voltage apparatus. In compressed gas insulation systems, floating
particles can initiate partial discharge activities which adversely
affect the working of insulation. Partial Discharges below the
inception voltage also plays a crucial in damaging the integrity of
insulation over a period of time. This paper discusses the effect of
loose and fixed Copper and Nichrome wire particles on the PD
characteristics in SF6-N2 (10:90) gas mixtures at a pressure of
0.4MPa. The Partial Discharge statistical parameters and their
correlation to the observed results are discussed.
Abstract: This paper presents a vertical silicon nanowire n- MOSFET integrated with a CMOS-compatible fully-silicided (FUSI) NiSi2 gate. Devices with nanowire diameter of 50nm show good electrical performance (SS < 70mV/dec, DIBL < 30mV/V, Ion/Ioff > 107). Most significantly, threshold voltage tunability of about 0.2V is shown. Although threshold voltage remains low for the 50nm diameter device, it is expected to become more positive as nanowire diameter reduces.
Abstract: The Object of this paper is to design and analyze a
Hysteresis modulation based sliding mode control (HMSMC) for
positive output elementary super lift Luo converter (POESLLC),
which is the start-of-the-art DC-DC converter. The positive output
elementary super lift Luo converter performs the voltage
conversion from positive source voltage to positive load voltage.
This paper proposes a HMSMC capable of providing the good
steady state and dynamic performance compared to conventional
controllers. Dynamic equations describing the positive output
elementary super lift luo converter are derived by using state space
average method. The simulation model of the positive output
elementary super lift Luo converter with its control circuit is
implemented in Matlab/Simulink. The HMSMC for positive
output elementary super lift Luo converter is tested for line
changes, load changes and also for components variations.
Abstract: DSTATCOM is one of the equipments for voltage sag mitigation in power systems. In this paper a new control method for balanced and unbalanced voltage sag mitigation using DSTATCOM is proposed. The control system has two loops in order to regulate compensator current and load voltage. Delayed signal cancellation has been used for sequence separation. The compensator should protect sensitive loads against different types of voltage sag. Performance of the proposed method is investigated under different types of voltage sags for linear and nonlinear loads. Simulation results show appropriate operation of the proposed control system.
Abstract: Reduced switching loss favours Pulse Skipping
Modulation mode of switching dc-to-dc converters at light loads.
Under certain conditions the converter operates in discontinuous
conduction mode (DCM). Inductor current starts from zero in each
switching cycle as the switching frequency is constant and not
adequately high. A DC-to-DC buck converter is modelled and
simulated in this paper under DCM. Effect of ESR of the filter
capacitor in input current frequency components is studied. The
converter is studied for its operation under input voltage and load
variation. The operating frequency is selected to be close to and
above audio range.
Abstract: This article proposes a current-mode square-rooting
circuit using current follower transconductance amplifier (CTFA).
The amplitude of the output current can be electronically controlled
via input bias current with wide input dynamic range. The proposed
circuit consists of only single CFTA. Without any matching
conditions and external passive elements, the circuit is then
appropriate for an IC architecture. The magnitude of the output signal
is temperature-insensitive. The PSpice simulation results are
depicted, and the given results agree well with the theoretical
anticipation. The power consumption is approximately 1.96mW at
±1.5V supply voltages.
Abstract: This paper describes a low-power second-order filter
for a continuous-time chopper stabilized capacitive sensor interface,
integrated with a fully differential post-CMOS surface-micromachined
MEMS pressure sensor. The circuit uses a single-ended
folded-cascode operational amplifier and two GM-C filters connected
in cascade. The circuit is realized in a 0.18 μm CMOS process and
offers differential to single-ended conversion. The novelty of the
scheme is the cascade of two GM-C filters to achieve a second-order
filter while minimizing power dissipation. The simulated filter cutoff
frequency is 1.14 kHz at common-mode voltage 1.65 V,
operating from a 3.3 V supply while dissipating 172μW of power.
The filter achieves an operating range of 1V for an output load of
1MOhm and 10pF.
Abstract: In this paper a novel, simple and reliable digital firing
scheme has been implemented for speed control of three-phase
induction motor using ac voltage controller. The system consists of
three-phase supply connected to the three-phase induction motor via
three triacs and its control circuit. The ac voltage controller has three
modes of operation depending on the shape of supply current. The
performance of the induction motor differs in each mode where the
speed is directly proportional with firing angle in two modes and
inversely in the third one. So, the control system has to detect the
current mode of operation to choose the correct firing angle of triacs.
Three sensors are used to feed the line currents to control system to
detect the mode of operation. The control strategy is implemented
using a low cost Xilinx Spartan-3E field programmable gate array
(FPGA) device. Three PI-controllers are designed on FPGA to
control the system in the three-modes. Simulation of the system is
carried out using PSIM computer program. The simulation results
show stable operation for different loading conditions especially in
mode 2/3. The simulation results have been compared with the
experimental results from laboratory prototype.
Abstract: This paper addresses control of commutation of switched reluctance (SR) motor without the use of a physical position detector. Rotor position detection schemes for SR motor based on magnetisation characteristics of the motor use normal excitation or applied current /voltage pulses. The resulting schemes are referred to as passive or active methods respectively. The research effort is in realizing an economical sensorless SR rotor position detector that is accurate, reliable and robust to suit a particular application. An effective and reliable means of generating commutation signals of an SR motor based on inductance profile of its stator windings determined using active probing technique is presented. The scheme has been validated online using a 4-phase 8/6 SR motor and an 8-bit processor.
Abstract: The operating control parameters of injection
flushing type of electrical discharge machining process on stainless
steel 304 workpiece with copper tools are being optimized
according to its individual machining characteristic i.e. material
removal rate (MRR). Lower MRR during EDM machining process
may decrease its- machining productivity. Hence, the quality
characteristic for MRR is set to higher-the-better to achieve the
optimum machining productivity. Taguchi method has been used
for the construction, layout and analysis of the experiment for each
of the machining characteristic for the MRR. The use of Taguchi
method in the experiment saves a lot of time and cost of preparing
and machining the experiment samples. Therefore, an L18
Orthogonal array which was the fundamental component in the
statistical design of experiments has been used to plan the
experiments and Analysis of Variance (ANOVA) is used to
determine the optimum machining parameters for this machining
characteristic. The control parameters selected for this
optimization experiments are polarity, pulse on duration, discharge
current, discharge voltage, machining depth, machining diameter
and dielectric liquid pressure. The result had shown that the higher
the discharge voltage, the higher will be the MRR.
Abstract: The High Voltage (HV) transmission mains into the community necessitate earthing design to ensure safety compliance of the system. Concrete poles are widely used within HV transmission mains; which could have an impact on the earth grid impedance and input impedance of the system from the fault point of view. This paper provides information on concrete pole earthing to enhance the split factor of the system; further, it discusses the deployment of concrete structures in high soil resistivity area to reduce the earth grid system of the plant. This paper introduces the cut off soil resistivity SC ρ when replacing timber poles with concrete ones.
Abstract: As there are also graph methods of circuit analysis in
addition to algebraic methods, it is, in theory, clearly possible to
carry out an analysis of a whole switched circuit in two-phase
switching exclusively by the graph method as well. This article deals
with two methods of full-graph solving of switched circuits: by
transformation graphs and by two-graphs. It deals with the circuit
switched capacitors and the switched current, too. All methods are
presented in an equally detailed steps to be able to compare.
Abstract: Deep Brain Stimulation or DBS is the second solution
for Parkinson's Disease. Its three parameters are: frequency, pulse
width and voltage. They must be optimized to achieve successful
treatment. Nowadays it is done clinically by neurologists and there is
not certain numerical method to detect them. The aim of this research
is to introduce simulation and modeling of Parkinson's Disease
treatment as a computational procedure to select optimum voltage.
We recorded finger tremor signals of some Parkinsonian patients
under DBS treatment at constant frequency and pulse width but
variable voltages; then, we adapted a new model to fit these data. The
optimum voltages obtained by data fitting results were the same as
neurologists- commented voltages, which means modeling can be
used as an engineering method to select optimum stimulation
voltages.
Abstract: The neural stimulation has been gaining much interest in neuromodulation research and clinical trials. For efficiency, there is a need for variable electrical stimulation such as current and voltage stimuli as well as wireless framework. In this regard, we develop the wireless neural stimulator capable of voltage and current stimuli. The system consists of ZigBee which is a wireless communication module and stimulus generator. The stimulus generator with 8-bits resolution enable both mono-polar and bi-polar waveform in voltage (-3.3~3.3V) and current(-330~330µA) stimulus mode which is controllable. The experimental results suggest that the proposed neural stimulator can play a role as an effective approach for neuromodulation.