Abstract: A new topology of unified power quality conditioner
(UPQC) is proposed for different power quality (PQ) improvement in
a three-phase four-wire (3P-4W) distribution system. For neutral
current mitigation, a star-hexagon transformer is connected in shunt
near the load along with three-leg voltage source inverters (VSIs)
based UPQC. For the mitigation of source neutral current, the uses of
passive elements are advantageous over the active compensation due
to ruggedness and less complexity of control. In addition to this, by
connecting a star-hexagon transformer for neutral current mitigation
the over all rating of the UPQC is reduced. The performance of the
proposed topology of 3P-4W UPQC is evaluated for power-factor
correction, load balancing, neutral current mitigation and mitigation
of voltage and currents harmonics. A simple control algorithm based
on Unit Vector Template (UVT) technique is used as a control
strategy of UPQC for mitigation of different PQ problems. In this
control scheme, the current/voltage control is applied over the
fundamental supply currents/voltages instead of fast changing APFs
currents/voltages, thereby reducing the computational delay.
Moreover, no extra control is required for neutral source current
compensation; hence the numbers of current sensors are reduced. The
performance of the proposed topology of UPQC is analyzed through
simulations results using MATLAB software with its Simulink and
Power System Block set toolboxes.
Abstract: Gas Metal Arc Welding (GMAW) processes is an
important joining process widely used in metal fabrication
industries. This paper addresses modeling and optimization of this
technique using a set of experimental data and regression analysis.
The set of experimental data has been used to assess the influence
of GMAW process parameters in weld bead geometry. The
process variables considered here include voltage (V); wire feed
rate (F); torch Angle (A); welding speed (S) and nozzle-to-plate
distance (D). The process output characteristics include weld bead
height, width and penetration. The Taguchi method and regression
modeling are used in order to establish the relationships between
input and output parameters. The adequacy of the model is
evaluated using analysis of variance (ANOVA) technique. In the
next stage, the proposed model is embedded into a Simulated
Annealing (SA) algorithm to optimize the GMAW process
parameters. The objective is to determine a suitable set of process
parameters that can produce desired bead geometry, considering
the ranges of the process parameters. Computational results prove
the effectiveness of the proposed model and optimization
procedure.
Abstract: in this work, we present a new strategy of direct adaptive control denoted: Extended minimal controller synthesis (EMCS). This algorithm is designed for an induction motor, which includes both electrical and mechanical dynamics under the assumptions of linear magnetic circuits. The main motivation of the EMCS control is to enhance the robustness of the MRAC algorithms, i.e. the rejection of bounded effects of rapidly varying external disturbances.
Abstract: In this paper, we show that the association of the PI
regulators for the speed and stator currents with a control strategy
using the linearization by state feedback for an induction machine
without speed sensor, and with an adaptation of the rotor resistance.
The rotor speed is estimated by using the model reference adaptive
system approach (MRAS). This method consists of using two
models: The first is the reference model and the second is an
adjustable one in which two components of the stator flux, obtained
from the measurement of the currents and stator voltages are
estimated. The estimated rotor speed is then obtained by canceling
the difference between stator-flux of the reference model and those
of the adjustable one. Satisfactory results of simulation are obtained
and discussed in this paper to highlight the proposed approach.
Abstract: This paper presents a remote on-line diagnostic system
for vehicles via the use of On-Board Diagnostic (OBD), GPS, and 3G
techniques. The main parts of the proposed system are on-board
computer, vehicle monitor server, and vehicle status browser. First,
the on-board computer can obtain the location of deriver and vehicle
status from GPS receiver and OBD interface, respectively. Then
on-board computer will connect with the vehicle monitor server
through 3G network to transmit the real time vehicle system status.
Finally, vehicle status browser could show the remote vehicle status
including vehicle speed, engine rpm, battery voltage, engine coolant
temperature, and diagnostic trouble codes. According to the
experimental results, the proposed system can help fleet managers and
car knockers to understand the remote vehicle status. Therefore this
system can decrease the time of fleet management and vehicle repair
due to the fleet managers and car knockers who find the diagnostic
trouble messages in time.
Abstract: One of the major disadvantages of the minimally
invasive surgery (MIS) is the lack of tactile feedback to the surgeon.
In order to identify and avoid any damage to the grasped complex
tissue by endoscopic graspers, it is important to measure the local
softness of tissue during MIS. One way to display the measured
softness to the surgeon is a graphical method. In this paper, a new
tactile sensor has been reported. The tactile sensor consists of an
array of four softness sensors, which are integrated into the jaws of a
modified commercial endoscopic grasper. Each individual softness
sensor consists of two piezoelectric polymer Polyvinylidene Fluoride
(PVDF) films, which are positioned below a rigid and a compliant
cylinder. The compliant cylinder is fabricated using a micro molding
technique. The combination of output voltages from PVDF films is
used to determine the softness of the grasped object. The theoretical
analysis of the sensor is also presented.
A method has been developed with the aim of reproducing the
tactile softness to the surgeon by using a graphical method. In this
approach, the proposed system, including the interfacing and the data
acquisition card, receives signals from the array of softness sensors.
After the signals are processed, the tactile information is displayed
by means of a color coding method. It is shown that the degrees of
softness of the grasped objects/tissues can be visually differentiated
and displayed on a monitor.
Abstract: High voltage generators are being subject to higher
voltage rating and are being designed to operate in harsh conditions.
Stator windings are the main component of generators in which
Electrical, magnetical and thermal stresses remain major failures for
insulation degradation accelerated aging. A large number of
generators failed due to stator winding problems, mainly insulation
deterioration. Insulation degradation assessment plays vital role in the
asset life management. Mostly the stator failure is catastrophic
causing significant damage to the plant. Other than generation loss,
stator failure involves heavy repair or replacement cost. Electro
thermal analysis is the main characteristic for improvement design of
stator slot-s insulation. Dielectric parameters such as insulation
thickness, spacing, material types, geometry of winding and slot are
major design consideration. A very powerful method available to
analyze electro thermal performance is Finite Element Method
(FEM) which is used in this paper. The analysis of various stator coil
and slot configurations are used to design the better dielectric system
to reduce electrical and thermal stresses in order to increase the
power of generator in the same volume of core. This paper describes
the process used to perform classical design and improvement
analysis of stator slot-s insulation.
Abstract: Electromagnetic flow meter by measuring the varying of magnetic flux, which is related to the velocity of conductive flow, can measure the rate of fluids very carefully and precisely. Electromagnetic flow meter operation is based on famous Faraday's second Law. In these equipments, the constant magnetostatic field is produced by electromagnet (winding around the tube) outside of pipe and inducting voltage that is due to conductive liquid flow is measured by electrodes located on two end side of the pipe wall. In this research, we consider to 2-dimensional mathematical model that can be solved by numerical finite difference (FD) solution approach to calculate induction potential between electrodes. The fundamental concept to design the electromagnetic flow meter, exciting winding and simulations are come out by using MATLAB and PDE-Tool software. In the last stage, simulations results will be shown for improvement and accuracy of technical provision.
Abstract: The general purpose processors that are used in
embedded systems must support constraints like execution time,
power consumption, code size and so on. On the other hand an
Application Specific Instruction-set Processor (ASIP) has advantages
in terms of power consumption, performance and flexibility. In this
paper, a 16-bit Application Specific Instruction-set processor for the
sensor data transfer is proposed. The designed processor architecture
consists of on-chip transmitter and receiver modules along with the
processing and controlling units to enable the data transmission and
reception on a single die. The data transfer is accomplished with less
number of instructions as compared with the general purpose
processor. The ASIP core operates at a maximum clock frequency of
1.132GHz with a delay of 0.883ns and consumes 569.63mW power
at an operating voltage of 1.2V. The ASIP is implemented in Verilog
HDL using the Xilinx platform on Virtex4.
Abstract: This paper presents a silicon controller rectifier (SCR)
based ESD protection circuit for IC. The proposed ESD protection
circuit has low trigger voltage and high holding voltage compared with
conventional SCR ESD protection circuit. Electrical characteristics of
the proposed ESD protection circuit are simulated and analyzed using
TCAD simulator. The proposed ESD protection circuit verified
effective low voltage ESD characteristics with low trigger voltage and
high holding voltage.
Abstract: The genetic algorithm (GA) based solution techniques
are found suitable for optimization because of their ability of
simultaneous multidimensional search. Many GA-variants have been
tried in the past to solve optimal power flow (OPF), one of the
nonlinear problems of electric power system. The issues like
convergence speed and accuracy of the optimal solution obtained
after number of generations using GA techniques and handling
system constraints in OPF are subjects of discussion. The results
obtained for GA-Fuzzy OPF on various power systems have shown
faster convergence and lesser generation costs as compared to other
approaches. This paper presents an enhanced GA-Fuzzy OPF (EGAOPF)
using penalty factors to handle line flow constraints and load
bus voltage limits for both normal network and contingency case
with congestion. In addition to crossover and mutation rate
adaptation scheme that adapts crossover and mutation probabilities
for each generation based on fitness values of previous generations, a
block swap operator is also incorporated in proposed EGA-OPF. The
line flow limits and load bus voltage magnitude limits are handled by
incorporating line overflow and load voltage penalty factors
respectively in each chromosome fitness function. The effects of
different penalty factors settings are also analyzed under contingent
state.
Abstract: Charging and discharging phenomenon on the surface
of materials can be found in plasma display panel, spacecraft
charging, high voltage insulator, etc. This report gives a simple
explanation on this phenomenon. A scanning electron microscope
was used not only as a tool to produce energetic electron beam to
charge an insulator without metallic coating and to produce a surface
discharging (surface breakdown/flashover) but also to observe the
visible charging and discharging on the sample surface. A model of
electric field distribution on the surface was developed in order to
explain charging and discharging phenomena. Since charging and
discharging process involves incubation time, therefore this process
can be used to evaluate the insulation property of materials under
electron bombardment.
Abstract: One of the major causes of voltage instability is the reactive power limit of the system. Improving the system's reactive power handling capacity via Flexible AC transmission System (FACTS) devices is a remedy for prevention of voltage instability and hence voltage collapse. In this paper, the effects of SVC and STATCOM in Static Voltage Stability Margin Enhancement will be studied. AC and DC representations of SVC and STATCOM are used in the continuation power flow process in static voltage stability study. The IEEE-14 bus system is simulated to test the increasing loadability. It is found that these controllers significantly increase the loadability margin of power systems.
Abstract: This paper presents a new and efficient approach for
capacitor placement in radial distribution systems that determine
the optimal locations and size of capacitor with an objective of
improving the voltage profile and reduction of power loss. The
solution methodology has two parts: in part one the loss sensitivity
factors are used to select the candidate locations for the capacitor
placement and in part two a new algorithm that employs Plant growth
Simulation Algorithm (PGSA) is used to estimate the optimal size
of capacitors at the optimal buses determined in part one. The main
advantage of the proposed method is that it does not require any
external control parameters. The other advantage is that it handles the
objective function and the constraints separately, avoiding the trouble
to determine the barrier factors. The proposed method is applied to 9
and 34 bus radial distribution systems. The solutions obtained by the
proposed method are compared with other methods. The proposed
method has outperformed the other methods in terms of the quality
of solution.
Abstract: In the present work, Pulsed Electro Acoustic (PEA)
technique was adopted to understand the space charge dynamics in
elastomeric material. It is observed that the polarity of the applied
DC voltage voltage and its magnitude alters the space charge
dynamics in insulation structure. It is also noticed that any addition
of compound to the base material/processing technique have
characteristic variation in the space charge injection process. It could
be concluded based on the present work that the plasticizer could
inject heterocharges into the insulation medium. Also it is realized
that space charge magnitude is less with the addition of plasticizer. In
the PEA studies, it is observed that local electric field in the
insulating material can be much more than applied electric field due
to space charge formation. One of the important conclusions arrived
at based on PEA technique is that one could understand the safe
operating electric field of an insulation material and the charge trap
sites.
Abstract: This paper proposes a new optimal feedback controller
for voltage source converters VSC's, for current regulated voltage
source converters, which allows compensate the harmonics of current
produced by nonlinear loads and load reactive power. The aim of the
present paper is to describe a novel switching signal generation
technique called optimal controller which guarantees that the injected
currents follow the reference currents determined by the
compensation strategy, with the smallest possible tracking error and
fixed switching frequency. It is compared with well-known
hysteresis current controller HCC. The validity of presented method
and its comparison with HCC is studied through simulation results.
Abstract: When a lightning strike falls near an overhead power
line, the intense electromagnetic field radiated by the current of the
lightning return stroke coupled with power lines and there induced
transient overvoltages, which can cause a back-flashover in electrical
network. The indirect lightning represents a major danger owing to
the fact that it is more frequent than that which results from the direct
strikes.
In this paper we present an analysis of the electromagnetic
coupling between an external electromagnetic field generated by the
lightning and an electrical overhead lines, so we give an important
and original contribution: We are based on our experimental
measurements which we carried in the high voltage laboratories of
EPFL in Switzerland during the last trimester of 2005, on the recent
works of other authors and with our mathematical improvement a
new particular analytical expression of the electromagnetic field
generated by the lightning return stroke was developed and presented
in this paper. The results obtained by this new electromagnetic field
formulation were compared with experimental results and give a
reasonable approach.
Abstract: In aircraft applications, according to the nature of
electrical equipment its location may be in unpressurized area or very
close to the engine; thus, the environmental conditions may change
from atmospheric pressure to less than 100 mbar, and the temperature
may be higher than the ambient one as in most real working
conditions of electrical equipment. Then, the classical Paschen curve
has to be replotted since these parameters may affect the discharge
ignition voltage. In this paper, we firstly investigate the domain of
validity of two corrective expressions on the Paschen-s law found in
the literature, in case of changing the air environment and known as
Peek and Dunbar corrections. Results show that these corrections are
no longer valid for combined variation of temperature and pressure.
After that, a new empirical expression for breakdown voltage is
proposed and is validated in the case of combined variations of
temperature and pressure.
Abstract: Voltage stability has become an important issue to many power systems around the world due to the weak systems and long line on power system networks. In this paper, MATLAB load flow program is applied to obtain the weak points in the system combined with finding the voltage stability limit. The maximum permissible loading of a system, within the voltage stability limit, is usually determined. The methods for varying tap ratio (using tap changing transformer) and applying different values of shunt capacitor injection to improve the voltage stability within the limit are also provided.
Abstract: Electric impedance imaging is a method of
reconstructing spatial distribution of electrical conductivity inside a
subject. In this paper, a new method of electrical impedance imaging
using eddy current is proposed. The eddy current distribution in the
body depends on the conductivity distribution and the magnetic field
pattern. By changing the position of magnetic core, a set of voltage
differences is measured with a pair of electrodes. This set of voltage
differences is used in image reconstruction of conductivity
distribution. The least square error minimization method is used as a
reconstruction algorithm. The back projection algorithm is used to
get two dimensional images. Based on this principle, a measurement
system is developed and some model experiments were performed
with a saline filled phantom. The shape of each model in the
reconstructed image is similar to the corresponding model,
respectively. From the results of these experiments, it is confirmed
that the proposed method is applicable in the realization of electrical
imaging.