Abstract: Generating random numbers are mainly used to create
secret keys or random sequences. It can be carried out by various
techniques. In this paper we present a very simple and efficient
pseudo random number generator (PRNG) based on chaotic maps
and S-Box tables. This technique adopted two main operations one to
generate chaotic values using two logistic maps and the second to
transform them into binary words using random S-Box tables.
The simulation analysis indicates that our PRNG possessing
excellent statistical and cryptographic properties.
Abstract: The capability of CNC gantry milling machines in
manufacturing long components has caused the expanded use of such
machines. On the other hand, the machines’ gantry rigidity can
reduce under severe loads or vibration during operation. Indeed, the
quality of machining is dependent on the machine’s dynamic
behavior throughout the operating process. For this reason, these
types of machines have always been used widely and are not
efficient. Therefore, they can usually be employed for rough
machining and may not produce adequate surface finishing. In this
paper, a CNC gantry milling machine with the potential to produce
good surface finish has been designed and analyzed. The lowest
natural frequency of this machine is 202 Hz corresponding to 12000
rpm at all motion amplitudes with a full range of suitable frequency
responses. Meanwhile, the maximum deformation under dead loads
for the gantry machine is 0.565*m, indicating that this machine tool
is capable of producing higher product quality.
Abstract: The operating control parameters of injection
flushing type of electrical discharge machining process on stainless
steel 304 workpiece with copper tools are being optimized
according to its individual machining characteristic i.e. material
removal rate (MRR). Lower MRR during EDM machining process
may decrease its- machining productivity. Hence, the quality
characteristic for MRR is set to higher-the-better to achieve the
optimum machining productivity. Taguchi method has been used
for the construction, layout and analysis of the experiment for each
of the machining characteristic for the MRR. The use of Taguchi
method in the experiment saves a lot of time and cost of preparing
and machining the experiment samples. Therefore, an L18
Orthogonal array which was the fundamental component in the
statistical design of experiments has been used to plan the
experiments and Analysis of Variance (ANOVA) is used to
determine the optimum machining parameters for this machining
characteristic. The control parameters selected for this
optimization experiments are polarity, pulse on duration, discharge
current, discharge voltage, machining depth, machining diameter
and dielectric liquid pressure. The result had shown that the higher
the discharge voltage, the higher will be the MRR.
Abstract: Nowadays, the demand for high product quality
focuses extensive attention to the quality of machined surface. The
(CNC) milling machine facilities provides a wide variety of
parameters set-up, making the machining process on the glass
excellent in manufacturing complicated special products compared to
other machining processes. However, the application of grinding
process on the CNC milling machine could be an ideal solution to
improve the product quality, but adopting the right machining
parameters is required. In glass milling operation, several machining
parameters are considered to be significant in affecting surface
roughness. These parameters include the lubrication pressure, spindle
speed, feed rate and depth of cut. In this research work, a fuzzy logic
model is offered to predict the surface roughness of a machined
surface in glass milling operation using CBN grinding tool. Four
membership functions are allocated to be connected with each input
of the model. The predicted results achieved via fuzzy logic model
are compared to the experimental result. The result demonstrated
settlement between the fuzzy model and experimental results with the
93.103% accuracy.
Abstract: The operating control parameters of injection
flushing type of electrical discharge machining process on stainless
steel 304 workpiece using copper tools are being optimized
according to its individual machining characteristic i.e. Electrode
Wear Ratio (EWR). Higher EWR would give bad dimensional
precision for the EDM machined workpiece because of high
electrode wear. Hence, the quality characteristic for EWR is set to
lower-the-better to achieve the optimum dimensional precision for
the machined workpiece. Taguchi method has been used for the
construction, layout and analysis of the experiment for EWR
machining characteristic. The use of Taguchi method in the
experiment saves a lot of time and cost of preparing and machining
the experiment samples. Therefore, an L18 Orthogonal array
which was the fundamental component in the statistical design of
experiments has been used to plan the experiments and Analysis of
Variance (ANOVA) is used to determine the optimum machining
parameters for this machining characteristic. The control
parameters selected for this optimization experiments are polarity,
pulse on duration, discharge current, discharge voltage, machining
depth, machining diameter and dielectric liquid pressure. The
result had shown that negative polarity machining parameter
setting will decreases EWR.