Abstract: Bio-composites derived from plant fiber and/or bioderived
polymer, are likely more ecofriendly and demonstrate
competitive performance with petroleum based composites. In this
research, the bio phenol-formaldehyde (bio-PF) was used as a matrix
and oil palm empty fruit bunch fiber (EFB) as reinforcement. The
matrix was synthesized via liquefaction and condensation to enhance
the combination of phenol and formaldehyde, during the process.
Then, the bio-PF was mixed with different percentage of EFB (5%,
10%, 15% and 20%) and molded at 180oC. The samples that viewed
under scanning electron microscopy (SEM) showed an excellent
wettability and interaction between EFB and matrix. Samples of 10%
EFB gave the optimum properties of impact and hardness meanwhile
sample 15% of EFB gave the highest reading of flexural modulus
(MOE) and flexural strength (MOR). For thermal stability analysis, it
was found that the weight loss and the activation energy (Ea) of the
bio-composites samples were decreased as the filler content
increased.
Abstract: In this study, composites were fabricated from oil
palm empty fruit bunch fiber and poly(lactic) acid by extrusion
followed by injection moulding. Surface of the fiber was pre-treated
by ultrasound in an alkali medium and treatment efficiency was
investigated by scanning electron microscopy (SEM) analysis and
Fourier transforms infrared spectrometer (FTIR). Effect of fiber
treatment on composite was characterized by tensile strength (TS),
tensile modulus (TM) and impact strength (IS). Furthermore,
biostrong impact modifier was incorporated into the treated fiber
composite to improve its impact properties. Mechanical testing
showed an improvement of up to 23.5% and 33.6% respectively for
TS and TM of treated fiber composite above untreated fiber
composite. On the other hand incorporation of impact modifier led to
enhancement of about 20% above the initial IS of the treated fiber
composite.
Abstract: In this study, microcrystalline cellulose (MCC) was
extracted from oil palm empty fruit bunch (EFB) cellulose which was
earlier isolated from oil palm EFB fibre. In order to isolate the
cellulose, the chlorination method was carried out. Then, the MCC
was prepared by simultaneous ultrasonic and alkali treatment from
the isolated α-cellulose. Based on mass balance calculation, the yields
for MCC obtained from EFB was 44%. For fiber characterization, it
is observed that the chemical composition of the hemicellulose and
lignin for all samples decreased while composition for cellulose
increased. The structural property of the MCC was studied by X-ray
diffraction (XRD) method and the result shows that the MCC
produced is a cellulose-I polymorph, with 73% crystallinity.
Abstract: Humic acids (HA) were produced by a Trichoderma
viride strain under submerged fermentation in a medium based on the
oil palm empty fruit bunch (EFB) and the main variables of the
process were optimized by using response surface methodology. A
temperature of 40°C and concentrations of 50g/L EFB, 5.7g/L potato
peptone and 0.11g/L (NH4)2SO4 were the optimum levels of the
variables that maximize the HA production, within the
physicochemical and biological limits of the process. The optimized
conditions led to an experimental HA concentration of 428.4±17.5
mg/L, which validated the prediction from the statistical model of
412.0mg/L. This optimization increased about 7–fold the HA
production previously reported in the literature. Additionally, the
time profiles of HA production and fungal growth confirmed our
previous findings that HA production preferably occurs during fungal
sporulation. The present study demonstrated that T. viride
successfully produced HA via the submerged fermentation of EFB
and the process parameters were successfully optimized using a
statistics-based response surface model. To the best of our
knowledge, the present work is the first report on the optimization of
HA production from EFB by a biotechnological process, whose
feasibility was only pointed out in previous works.
Abstract: A statistical optimization of the saccharification
process of EFB was studied. The statistical analysis was done by
applying faced centered central composite design (FCCCD) under
response surface methodology (RSM). In this investigation, EFB
dose, enzyme dose and saccharification period was examined, and the
maximum 53.45% (w/w) yield of reducing sugar was found with 4%
(w/v) of EFB, 10% (v/v) of enzyme after 120 hours of incubation. It
can be calculated that the conversion rate of cellulose content of the
substrate is more than 75% (w/w) which can be considered as a
remarkable achievement. All the variables, linear, quadratic and
interaction coefficient, were found to be highly significant, other than
two coefficients, one quadratic and another interaction coefficient.
The coefficient of determination (R2) is 0.9898 that confirms a
satisfactory data and indicated that approximately 98.98% of the
variability in the dependent variable, saccharification of EFB, could
be explained by this model.
Abstract: The use of synthetic retardants in polymeric insulated
cables is not uncommon in the high voltage engineering to study
electrical treeing phenomenon. However few studies on organic
materials for the same investigation have been carried. .This paper
describes the study on the effects of Oil Palm Empty Fruit Bunch
(OPEFB) microfiller on the tree initiation and propagation in silicone
rubber with different weight percentages (wt %) of filler to insulation
bulk material. The weight percentages used were 0 wt % and 1 wt %
respectively. It was found that the OPEFB retards the propagation of
the electrical treeing development. For tree inception study, the
addition of 1(wt %) OPEFB has increase the tree inception voltage of
silicone rubber. So, OPEFB is a potential retardant to the initiation
and growth of electrical treeing occurring in polymeric materials for
high voltage application. However more studies on the effects of
physical and electrical properties of OPEFB as a tree retardant
material are required.
Abstract: Alkali treated oil palm empty fruit bunch (EFB) fibres
(TEFBF) and untreated EFBF fibers (UEFBF) were incorporated in
polypropylene (PP) with and without malic anhydride grafted PP
(MAPP) and magnesium hydroxide as flame retardant (FR) to
produce TEFBF-PP and UEFBF-PP composites by the melt casting
method. The composites were characterized by mechanical and
burning tests along with a scanning electron microscope and Fourier
transform infrared spectroscopy. The significant improvement in
flexural modulus (133%) and flame retardant property (60%) of
TEFBF-PP composite with MAPP and FR is observed. The improved
mechanical property is discussed by the development of encapsulated
textures.
Abstract: Pretreatment of oil palm empty fruit bunch (OPEFB) with N-Methylmorpholine-N-oxide (NMMO) to enhance biogas production was investigated. The pretreatments were performed at 90 and 120ºC for 1, 3, and 5 h using three different concentrations of NMMO of 73%, 79%, and 85%. The pretreated OPEFB was subsequently anaerobically digested to produce biogas. After pretreatment, there were no significant changes of the main composition of OPEFB and the maximum total solid recovery was 92%. The amorphous phase was increased up to 78% at pretreatment condition using 85% NMMO solution for 3 h at 120oC. In general, higher concentration of NMMO and higher temperature resulted in increased amorphous form and higher biogas production. The best results of biogas production reached enhancement of methane yield of 148% compared to the untreated OPEFB and increased in digestion of 94% compared to starch as reference.