Abstract: Power line communications may be used as a data
communication channel in public and indoor distribution networks so
that it does not require the installing of new cables. Industrial low
voltage distribution network may be utilized for data transfer
required by the on-line condition monitoring of electric motors. This
paper presents a pilot distribution network for modeling low voltage
power line as data transfer channel. The signal attenuation in
communication channels in the pilot environment is presented and
the analysis is done by varying the corresponding parameters for the
signal attenuation.
Abstract: This paper, a simple continuous conduction mode (CCM) pulse-width-modulated (PWM) controller for high power factor boost converters is introduced. The duty ratios were obtained by the comparison of a sensed signal from inductor current or switch current and a negative slope ramp carrier waveform in each switching period. Due to the proposed control requires only the inductor current or switch current sensor and the output voltage sensor, its circuit implementation was very simple. To verify the proposed control, the circuit experimentation of a 350 W boost converter with the proposed control was applied. From the results, the input current waveform was shaped to be closely sinusoidal, implying high power factor and low harmonics.
Abstract: By analyzing the sources of energy and power
loss in PWM (Pulse Width Modulation) controlled drivers of
water electrolysis cells, it is possible to reduce the power
dissipation and enhance the efficiency of such hydrogen
production units. A PWM controlled power driver is based on
a semiconductor switching element where its power
dissipation might be a remarkable fraction of the total power
demand of an electrolysis system. Power dissipation in a
semiconductor switching element is related to many different
parameters which could be fitted into two main categories:
switching losses and conduction losses. Conduction losses are
directly related to the built, structure and capabilities of a
switching device itself and indeed the conditions in which the
element is handling the switching application such as voltage,
current, temperature and of course the fabrication technology.
On the other hand, switching losses have some other
influencing variables other than the mentioned such as control
system, switching method and power electronics circuitry of
the PWM power driver. By analyzings the characteristics of
recently developed power switching transistors from different
families of Bipolar Junction Transistors (BJT), Metal Oxide
Semiconductor Field Effect Transistors (MOSFET) and
Insulated Gate Bipolar Transistors (IGBT), some
recommendations are made in this paper which are able to
lead to achieve higher hydrogen production efficiency by
utilizing PWM controlled water electrolysis cells.
Abstract: With getting older in the whole population, the
prevalence of stroke and its residual disability is getting higher and
higher recently in Taiwan. The functional electrical stimulation
cycling system (FESCS) is useful for hemiplegic patients. Because
that the muscle of stroke patients is under hybrid activation. The raw
electromyography (EMG) represents the residual muscle force of
stroke subject whereas the peak-to-peak of stimulus EMG indicates the
force enhancement benefiting from ES. It seems that EMG signals
could be used for a parameter of feedback control mechanism. So, we
design the feedback control protocol of FESCS, it includes
physiological signal recorder, FPGA biomedical module, DAC and
electrical stimulation circuit. Using the intensity of real-time EMG
signal obtained from patients, as a feedback control method for the
output voltage of FES-cycling system.
Abstract: This paper presents positive and negative full-wave
rectifier. The proposed structure is based on OTA using
commercially available ICs (LT1228). The features of the proposed
circuit are that: it can rectify and amplify voltage signal with
controllable output magnitude via input bias current: the output
voltage is free from temperature variation. The circuit description
merely consists of 1 single ended and 3 fully differential OTAs. The
performance of the proposed circuit are investigated though PSpice.
They show that the proposed circuit can function as positive/negative
full-wave rectifier, where the voltage input wide-dynamic range from
-5V to 5V. Furthermore, the output voltage is slightly dependent on
the temperature variations.
Abstract: This paper proposes a low power SRAM based on
five transistor SRAM cell. Proposed SRAM uses novel word-line
decoding such that, during read/write operation, only selected cell
connected to bit-line whereas, in conventional SRAM (CV-SRAM),
all cells in selected row connected to their bit-lines, which in turn
develops differential voltages across all bit-lines, and this makes
energy consumption on unselected bit-lines. In proposed SRAM
memory array divided into two halves and this causes data-line
capacitance to reduce. Also proposed SRAM uses one bit-line and
thus has lower bit-line leakage compared to CV-SRAM.
Furthermore, the proposed SRAM incurs no area overhead, and has
comparable read/write performance versus the CV-SRAM.
Simulation results in standard 0.25μm CMOS technology shows in
worst case proposed SRAM has 80% smaller dynamic energy
consumption in each cycle compared to CV-SRAM. Besides, energy
consumption in each cycle of proposed SRAM and CV-SRAM
investigated analytically, the results of which are in good agreement
with the simulation results.
Abstract: Due to the deregulation of the Electric Supply
Industry and the resulting emergence of electricity market, the
volumes of power purchases are on the rise all over the world. In a
bid to meet the customer-s demand in a reliable and yet economic
manner, utilities purchase power from the energy market over and
above its own production. This paper aims at developing an optimal
power purchase model with two objectives viz economy and
environment ,taking various functional operating constraints such as
branch flow limits, load bus voltage magnitudes limits, unit capacity
constraints and security constraints into consideration.The price of
purchased power being an uncertain variable is modeled using fuzzy
logic. DEMO (Differential Evolution For Multi-objective
Optimization) is used to obtain the pareto-optimal solution set of the
multi-objective problem formulated. Fuzzy set theory has been
employed to extract the best compromise non-dominated solution.
The results obtained on IEEE 30 bus system are presented and
compared with that of NSGAII.
Abstract: An appropriate method for fault identification and classification on extra high voltage transmission line using discrete wavelet transform is proposed in this paper. The sharp variations of the generated short circuit transient signals which are recorded at the sending end of the transmission line are adopted to identify the fault. The threshold values involve fault classification and these are done on the basis of the multiresolution analysis. A comparative study of the performance is also presented for Discrete Fourier Transform (DFT) based Artificial Neural Network (ANN) and Discrete Wavelet Transform (DWT). The results prove that the proposed method is an effective and efficient one in obtaining the accurate result within short duration of time by using Daubechies 4 and 9. Simulation of the power system is done using MATLAB.
Abstract: Direct conversion of methane to methanol by partial oxidation in a thermal reactor has a poor yield of about 2% which is less than the expected economical yield of about 10%. Conventional thermal catalytic reactors have been proposed to be superseded by plasma reactors as a promising approach, due to strength of the electrical energy which can break C-H bonds of methane. Among the plasma techniques, non-thermal dielectric barrier discharge (DBD) plasma chemical process is one of the most future promising technologies in synthesizing methanol. The purpose of this paper is presenting a brief review of CH4 oxidation with O2 in DBD plasma reactors based on the recent investigations. For this reason, the effect of various parameters of reactor configuration, feed ratio, applied voltage, residence time (gas flow rate), type of applied catalyst, pressure and reactor wall temperature on methane conversion and methanol selectivity are discussed.
Abstract: In this paper we ultra low-voltage and high speed CMOS domino logic. For supply voltages below 500mV the delay for a ultra low-voltage NAND2 gate is aproximately 10% of a complementary CMOS inverter. Furthermore, the delay variations due to mismatch is much less than for conventional CMOS. Differential domino gates for AND/NAND and OR/NOR operation are presented.
Abstract: This paper deals with the comparison between two proposed control strategies for a DC-DC boost converter. The first control is a classical Sliding Mode Control (SMC) and the second one is a distance based Fuzzy Sliding Mode Control (FSMC). The SMC is an analytical control approach based on the boost mathematical model. However, the FSMC is a non-conventional control approach which does not need the controlled system mathematical model. It needs only the measures of the output voltage to perform the control signal. The obtained simulation results show that the two proposed control methods are robust for the case of load resistance and the input voltage variations. However, the proposed FSMC gives a better step voltage response than the one obtained by the SMC.
Abstract: An efficient architecture for low jitter All Digital
Phase Locked Loop (ADPLL) suitable for high speed SoC
applications is presented in this paper. The ADPLL is designed using
standard cells and described by Hardware Description Language
(HDL). The ADPLL implemented in a 90 nm CMOS process can
operate from 10 to 200 MHz and achieve worst case frequency
acquisition in 14 reference clock cycles. The simulation result shows
that PLL has cycle to cycle jitter of 164 ps and period jitter of 100 ps
at 100MHz. Since the digitally controlled oscillator (DCO) can
achieve both high resolution and wide frequency range, it can meet
the demands of system-level integration. The proposed ADPLL can
easily be ported to different processes in a short time. Thus, it can
reduce the design time and design complexity of the ADPLL, making
it very suitable for System-on-Chip (SoC) applications.
Abstract: In this paper, a one-dimensional numerical approach is
used to study the effect of applying electrohydrodynamics on the
temperature and species mass fraction profiles along the microcombustor.
Premixed mixture is H2-Air with a multi-step chemistry
(9 species and 19 reactions). In the micro-scale combustion because
of the increasing ratio of area-to-volume, thermal and radical
quenching mechanisms are important. Also, there is a significant heat
loss from the combustor walls. By inserting a number of electrodes
into micro-combustor and applying high voltage to them corona
discharge occurs. This leads in moving of induced ions toward
natural molecules and colliding with them. So this phenomenon
causes the movement of the molecules and reattaches the flow to the
walls. It increases the velocity near the walls that reduces the wall
boundary layer. Consequently, applying electrohydrodynamics
mechanism can enhance the temperature profile in the microcombustor.
Ultimately, it prevents the flame quenching in microcombustor.
Abstract: This article presents a current-mode quadrature
oscillator using differential different current conveyor (DDCC) and
voltage differencing transconductance amplifier (VDTA) as active
elements. The proposed circuit is realized fro m a non-inverting
lossless integrator and an inverting second order low-pass filter. The
oscillation condition and oscillation frequency can be
electronically/orthogonally controlled via input bias currents. The
circuit description is very simple, consisting of merely 1 DDCC, 1
VDTA, 1 grounded resistor and 3 grounded capacitors. Using only
grounded elements, the proposed circuit is then suitable for IC
architecture. The proposed oscillator has high output impedance
which is easy to cascade or dive the external load without the buffer
devices. The PSPICE simulation results are depicted, and the given
results agree well with the theoretical anticipation. The power
consumption is approximately 1.76mW at ±1.25V supply voltages.
Abstract: This paper present a MATLAB-SIMULINK model of a single phase 2.5 KVA, 240V RMS controlled PV VSI (Photovoltaic Voltage Source Inverter) inverter using IGBTs (Insulated Gate Bipolar Transistor). The behavior of output voltage, output current, and the total harmonic distortion (THD), with the variation in input dc blocking capacitor (Cdc), for linear and non-linear load has been analyzed. The values of Cdc as suggested by the other authors in their papers are not clearly defined and it poses difficulty in selecting the proper value. As the dc power stored in Cdc, (generally placed parallel with battery) is used as input to the VSI inverter. The simulation results shows the variation in the output voltage and current with different values of Cdc for linear and non-linear load connected at the output side of PV VSI inverter and suggest the selection of suitable value of Cdc.
Abstract: The integrity and issues related to electrostatic performance associated with scaling Si MOSFET bulk sub 10nm channel length promotes research in new device architectures such as SOI, double gate and GAA MOSFET. In this paper, we present some novel characteristic of horizontal rectangular gate\gate all around MOSFETs with dual metal of gate we obtained using SILVACO TCAD tools. We will also exhibit some simulation results we obtained relating to the influence of some parameters variation on our structure, that having a direct impact on their threshold voltage and drain current. In addition, our TFET showed reasonable ION/IOFF ratio of (104) and low drain induced barrier lowering (DIBL) of 39 mV/V.
Abstract: The paper presents a simple and an accurate formula
that has been developed for the conduction angle (δ) of a single
phase half-wave or full-wave controlled rectifier with RL load. This
formula can be also used for calculating the conduction angle (δ) in
case of A.C. voltage regulator with inductive load under
discontinuous current mode. The simulation results shows that the
conduction angle calculated from the developed formula agree very
well with that obtained from the exact solution arrived from the
iterative method. Applying the developed formula can reduce the
computational time and reduce the time for manual classroom
calculation. In addition, the proposed formula is attractive for real
time implementations.
Abstract: The Inter feeder Power Flow Regulator (IFPFR)
proposed in this paper consists of several voltage source inverters
with common dc bus; each inverter is connected in series with one of
different independent distribution feeders in the power system. This
paper is concerned with how to transfer power between the feeders for
load sharing purpose. The power controller of each inverter injects
the power (for sending feeder) or absorbs the power (for receiving
feeder) via injecting suitable voltage; this voltage injection is
simulated by voltage drop across series virtual impedance, the
impedance value is selected to achieve the concept of power exchange
between the feeders without perturbing the load voltage magnitude of
each feeder. In this paper a new control scheme for load sharing using
IFPFR is proposed.
Abstract: Particle Swarm Optimization (PSO) with elite PSO
parameters has been developed for power flow analysis under
practical constrained situations. Multiple solutions of the power flow
problem are useful in voltage stability assessment of power system.
A method of determination of multiple power flow solutions is
presented using a hybrid of Particle Swarm Optimization (PSO) and
local search technique. The unique and innovative learning factors of
the PSO algorithm are formulated depending upon the node power
mismatch values to be highly adaptive with the power flow problems.
The local search is applied on the pbest solution obtained by the PSO
algorithm in each iteration. The proposed algorithm performs reliably
and provides multiple solutions when applied on standard and illconditioned
systems. The test results show that the performances of
the proposed algorithm under critical conditions are better than the
conventional methods.
Abstract: This paper presents the experimental results on
artificial ageing test of 22 kV XLPE cable for distribution system
application in Thailand. XLPE insulating material of 22 kV cable
was sliced to 60-70 μm in thick and was subjected to ac high voltage
at 23
Ôùª
C, 60
Ôùª
C and 75
Ôùª
C. Testing voltage was constantly applied to
the specimen until breakdown. Breakdown voltage and time to
breakdown were used to evaluate life time of insulating material.
Furthermore, the physical model by J. P. Crine for predicts life time
of XLPE insulating material was adopted as life time model and was
calculated in order to compare the experimental results. Acceptable
life time results were obtained from Crine-s model comparing with
the experimental result. In addition, fourier transform infrared
spectroscopy (FTIR) for chemical analysis and scanning electron
microscope (SEM) for physical analysis were conducted on tested
specimens.