Abstract: In this paper we present the modeling, design, and
experimental testing of a nerve cuff multi-electrode system for
diameter-selective vagus nerve stimulation.
The multi-electrode system contained ninety-nine platinum
electrodes embedded within a self-curling spiral silicone sheet. The
electrodes were organized in a matrix having nine parallel groups,
each containing eleven electrodes.
Preliminary testing of the nerve cuff was performed in an isolated
segment of a swinish left cervical vagus nerve. For selective vagus
nerve stimulation, precisely defined current quasitrapezoidal,
asymmetric and biphasic stimulating pulses were applied to
preselected locations along the left vagus segment via appointed
group of three electrodes within the cuff. Selective stimulation was
obtained by anodal block. However, these pulses may not be safe for
a long-term application because of a frequently used high imbalance
between the cathodic and anodic part of the stimulating pulse.
Preliminary results show that the cuff was capable of exciting A
and B-fibres, and, that for a certain range of parameters used in
stimulating pulses, the contribution of A-fibres to the CAP was
slightly reduced and the contribution of B-fibres was slightly larger.
Results also showed that measured CAPs are not greatly
influenced by the imbalance between a charge Qc injected in cathodic
and Qa in anodic phase of quasitrapezoidal, asymmetric and biphasic
pulses.
Abstract: Magnetic and semiconductor nanomaterials exhibit
novel magnetic and optical properties owing to their unique size and
shape-dependent effects. With shrinking the size down to nanoscale
region, various anomalous properties that normally not present in bulk
start to dominate. Ability in harnessing of these anomalous properties
for the design of various advance electronic devices is strictly
dependent on synthetic strategies. Hence, current research has focused
on developing a rational synthetic control to produce high quality
nanocrystals by using organometallic approach to tune both size and
shape of the nanomaterials. In order to elucidate the growth
mechanism, transmission electron microscopy was employed as a
powerful tool in performing real time-resolved morphologies and
structural characterization of magnetic (Fe3O4) and semiconductor
(ZnO) nanocrystals. The current synthetic approach is found able to
produce nanostructures with well-defined shapes. We have found that
oleic acid is an effective capping ligand in preparing oxide-based
nanostructures without any agglomerations, even at high temperature.
The oleate-based precursors and capping ligands are fatty acid
compounds, which are respectively originated from natural palm oil
with low toxicity. In comparison with other synthetic approaches in
producing nanostructures, current synthetic method offers an effective
route to produce oxide-based nanomaterials with well-defined shapes
and good monodispersity. The nanocystals are well-separated with
each other without any stacking effect. In addition, the as-synthesized
nanopellets are stable in terms of chemically and physically if
compared to those nanomaterials that are previous reported. Further
development and extension of current synthetic strategy are being
pursued to combine both of these materials into nanocomposite form
that will be used as “smart magnetic nanophotocatalyst" for industry
waste water treatment.
Abstract: Nanocrystals (NC) alloyed composite CdSxSe1-x(x=0
to 1) have been prepared using the chemical solution deposition
technique. The energy band gap of these alloyed nanocrystals of
approximately the same size, have been determined by scanning
tunneling spectroscopy (STS) technique at room temperature. The
values of the energy band gap obtained directly using STS are
compared to those measured by optical spectroscopy. Increasing the
molar fraction ratio x from 0 to 1 causes clearly observed increase in
the band gap of the alloyed composite nanocrystal. Vegard-s law was
applied to calculate the parameters of the effective mass
approximation (EMA) model and the dimension obtained were
compared to the values measured by STM. The good agreement of
the calculated and measured values is a direct result of applying
Vegard's law in the nanocomposites.
Abstract: This paper presents the simulation results of electric field and potential distributions along surface of silicone rubber polymer insulators under clean and various contamination conditions with/without water droplets. Straight sheds insulator having leakage distance 290 mm was used in this study. Two type of contaminants, playwood dust and cement dust, have been studied the effect of contamination on the insulator surface. The objective of this work is to comparison the effect of contamination on potential and electric field distributions along the insulator surface when water droplets exist on the insulator surface. Finite element method (FEM) is adopted for this work. The simulation results show that contaminations have no effect on potential distribution along the insulator surface while electric field distributions are obviously depended on contamination conditions.
Abstract: It is important to predict yield in semiconductor test process in order to increase yield. In this study, yield prediction means finding out defective die, wafer or lot effectively. Semiconductor test process consists of some test steps and each test includes various test items. In other world, test data has a big and complicated characteristic. It also is disproportionably distributed as the number of data belonging to FAIL class is extremely low. For yield prediction, general data mining techniques have a limitation without any data preprocessing due to eigen properties of test data. Therefore, this study proposes an under-sampling method using support vector machine (SVM) to eliminate an imbalanced characteristic. For evaluating a performance, randomly under-sampling method is compared with the proposed method using actual semiconductor test data. As a result, sampling method using SVM is effective in generating robust model for yield prediction.
Abstract: Vertical ZnO nanowire array films were synthesized
based on aqueous method for sensing applications. ZnO nanowires
were investigated structurally using X-ray diffraction (XRD) and
scanning electron microscopy (SEM). The gas-sensing properties of
ZnO nanowires array films are studied. It is found that the ZnO
nanowires array film sensor exhibits excellent sensing properties
towards O2 and CO2 at 100 °C with the response time shorter than 5
s. High surface area / volume ratio of vertical ZnO nanowire and high
mobility accounts for the fast response and recovery. The sensor
response was measured in the range from 100 to 500 ppm O2 and CO2
in this study.
Abstract: In order to realize long-lived electric propulsion
systems, we have been investigating an electrodeless plasma thruster.
In our concept, a helicon plasma is accelerated by the magnetic nozzle
for the thrusts production. In addition, the electromagnetic thrust can
be enhanced by the additional radio-frequency rotating electric field
(REF) power in the magnetic nozzle. In this study, a direct
measurement of the electromagnetic thrust and a probe measurement
have been conducted using a laboratory model of the thruster under the
condition without the REF power input. Fromthrust measurement, it is
shown that the thruster produces a sub-milli-newton order
electromagnetic thrust force without the additional REF power. The
thrust force and the density jump are observed due to the discharge
mode transition from the inductive coupled plasma to the helicon wave
excited plasma. The thermal thrust is theoretically estimated, and the
total thrust force, which is a sum of the electromagnetic and the
thermal thrust force and specific impulse are calculated to be up to 650
μN (plasma production power of 400 W, Ar gas mass flow rate of 1.0
mg/s) and 210 s (plasma production power of 400 W, Ar gas mass flow
rate of 0.2 mg/s), respectively.
Abstract: A closed-loop controlled wireless power transmission circuit block for implantable biomedical applications is described in this paper. The circuit consists of one front-end rectifier, power management sub-block including bandgap reference and low drop-out regulators (LDOs) as well as transmission power detection / feedback circuits. Simulation result shows that the front-end rectifier achieves 80% power efficiency with 750-mV single-end peak-to-peak input voltage and 1.28-V output voltage under load current of 4 mA. The power management block can supply 1.8mA average load current under 1V consuming only 12μW power, which is equivalent to 99.3% power efficiency. The wireless power transmission block described in this paper achieves a maximum power efficiency of 80%. The wireless power transmission circuit block is designed and implemented using UMC 65-nm CMOS/RF process. It occupies 1 mm × 1.2 mm silicon area.
Abstract: Carbon nanotubes (CNTs) possess unique structural,
mechanical, thermal and electronic properties, and have been
proposed to be used for applications in many fields. However, to
reach the full potential of the CNTs, many problems still need to be
solved, including the development of an easy and effective
purification procedure, since synthesized CNTs contain impurities,
such as amorphous carbon, carbon nanoparticles and metal particles.
Different purification methods yield different CNT characteristics
and may be suitable for the production of different types of CNTs. In
this study, the effect of different purification chemicals on carbon
nanotube quality was investigated. CNTs were firstly synthesized by
chemical vapor deposition (CVD) of acetylene (C2H2) on a
magnesium oxide (MgO) powder impregnated with an iron nitrate
(Fe(NO3)3·9H2O) solution. The synthesis parameters were selected
as: the synthesis temperature of 800°C, the iron content in the
precursor of 5% and the synthesis time of 30 min. The liquid phase
oxidation method was applied for the purification of the synthesized
CNT materials. Three different acid chemicals (HNO3, H2SO4, and
HCl) were used in the removal of the metal catalysts from the
synthesized CNT material to investigate the possible effects of each
acid solution to the purification step. Purification experiments were
carried out at two different temperatures (75 and 120 °C), two
different acid concentrations (3 and 6 M) and for three different time
intervals (6, 8 and 15 h). A 30% H2O2 : 3M HCl (1:1 v%) solution
was also used in the purification step to remove both the metal
catalysts and the amorphous carbon. The purifications using this
solution were performed at the temperature of 75°C for 8 hours.
Purification efficiencies at different conditions were evaluated by
thermogravimetric analysis. Thermal and electrical properties of
CNTs were also determined. It was found that the obtained electrical
conductivity values for the carbon nanotubes were typical for organic
semiconductor materials and thermal stabilities were changed
depending on the purification chemicals.
Abstract: Parallel Prefix addition is a technique for improving
the speed of binary addition. Due to continuing integrating intensity
and the growing needs of portable devices, low-power and highperformance
designs are of prime importance. The classical parallel
prefix adder structures presented in the literature over the years
optimize for logic depth, area, fan-out and interconnect count of logic
circuits. In this paper, a new architecture for performing 8-bit, 16-bit
and 32-bit Parallel Prefix addition is proposed. The proposed prefix
adder structures is compared with several classical adders of same
bit width in terms of power, delay and number of computational
nodes. The results reveal that the proposed structures have the least
power delay product when compared with its peer existing Prefix
adder structures. Tanner EDA tool was used for simulating the adder
designs in the TSMC 180 nm and TSMC 130 nm technologies.
Abstract: In this work, an organic compound 5,10,15,20-
Tetrakis(3,5-di-tertbutylphenyl)porphyrinatocopper(II) (TDTBPPCu)
is studied as an active material for thin film electronic devices. To
investigate the electrical properties of TDTBPPCu, junction of
TDTBPPCu with heavily doped n-Si and Al is fabricated.
TDTBPPCu film was sandwiched between Al and n-Si electrodes.
Various electrical parameters of TDTBPPCu are determined. The
current-voltage characteristics of the junction are nonlinear,
asymmetric and show rectification behavior, which gives the clue of
formation of depletion region. This behavior indicates the potential
of TDTBPPCu for electronics applications. The current-voltage and
capacitance-voltage techniques are used to find the different
electronic parameters.
Abstract: There are few studies on eggshell of leatherback turtle
which is endangered species in Thailand. This study was focusing on
the ultrastructure and elemental composition of leatherback turtle
eggshells collected from Andaman Sea Shore, Thailand during the
nesting season using scanning electron microscope (SEM). Three
eggshell layers of leatherback turtle; the outer cuticle layer or
calcareous layer, the middle layer or middle multistrata layer and the
inner fibrous layer were recognized. The outer calcareous layer was
thick and porosity which consisted of loose nodular units of various
crystal shapes and sizes. The loose attachment between these units
resulted in numerous spaces and openings. The middle layer was
compact thick with several multistrata and contained numerous
openings connecting to both outer cuticle layer and inner fibrous
layer. The inner fibrous layer was compact and thin, and composed of
numerous reticular fibers. Energy dispersive X-ray microanalysis
detector revealed energy spectrum of X-rays character emitted from
all elements on each layer. The percentages of all elements were
found in the following order: carbon (C) > oxygen (O) > calcium
(Ca) > sulfur (S) > potassium (K) > aluminum (Al) > iodine (I) >
silicon (Si) > chlorine (Cl) > sodium (Na) > fluorine (F) >
phosphorus (P) > magnesium (Mg). Each layer consisted of high
percentage of CaCO3 (approximately 98%) implying that it was
essential for turtle embryonic development. A significant difference
was found in the percentages of Ca and Mo in the 3layers. Moreover,
transition metal, metal and toxic non-metal contaminations were
found in leatherback turtle eggshell samples. These were palladium
(Pd), molybdenum (Mo), copper (Cu), aluminum (Al), lead (Pb), and
bromine (Br). The contamination elements were seen in the outer
layers except for Mo. All elements were readily observed and
mapped using Smiling program. X-ray images which mapped the
location of all elements were showed. Calcium containing in the
eggshell appeared in high contents and was widely distributing in
clusters of the outer cuticle layer to form CaCO3 structure. Moreover,
the accumulation of Na and Cl was observed to form NaCl which was
widely distributing in 3 eggshell layers. The results from this study
would be valuable on assessing the emergent success in this
endangered species.
Abstract: The most widely used semiconductor memory types
are the Dynamic Random Access Memory (DRAM) and Static
Random Access memory (SRAM). Competition among memory
manufacturers drives the need to decrease power consumption and
reduce the probability of read failure. A technology that is relatively
new and has not been explored is the FinFET technology. In this
paper, a single cell Schmitt Trigger Based Static RAM using FinFET
technology is proposed and analyzed. The accuracy of the result is
validated by means of HSPICE simulations with 32nm FinFET
technology and the results are then compared with 6T SRAM using
the same technology.
Abstract: We present a dextran modified silicon microring
resonator sensor for high density antibody immobilization. An array
of sensors consisting of three sensor rings and a reference ring was
fabricated and its surface sensitivity and the limit of detection were
obtained using polyelectrolyte multilayers. The mass sensitivity and
the limit of detection of the fabricated sensor ring are 0.35 nm/ng
mm-2 and 42.8 pg/mm2 in air, respectively. Dextran modified sensor
surface was successfully prepared by covalent grafting of oxidized
dextran on 3-aminopropyltriethoxysilane (APTES) modified silicon
sensor surface. The antibody immobilization on hydrogel dextran
matrix improves 40% compared to traditional antibody
immobilization method via APTES and glutaraldehyde linkage.
Abstract: Semiconductor detector arrays are widely used in
high-temperature plasma diagnostics. They have a fast response,
which allows observation of many processes and instabilities in
tokamaks. In this paper, there are reviewed several diagnostics based
on semiconductor arrays as cameras, AXUV photodiodes (referred
often as fast “bolometers") and detectors of both soft X-rays and
visible light installed on the COMPASS tokamak recently. Fresh
results from both spring and summer campaigns in 2012 are
introduced. Examples of the utilization of the detectors are shown on
the plasma shape determination, fast calculation of the radiation
center, two-dimensional plasma radiation tomography in different
spectral ranges, observation of impurity inflow, and also on
investigation of MHD activity in the COMPASS tokamak discharges.
Abstract: The threshold voltage and capacitance voltage characteristics of ultra-thin Silicon-on-Insulator MOSFET are greatly influenced by the thickness and doping concentration of the silicon film. In this work, the capacitance voltage characteristics and threshold voltage of the device have been analyzed with quantum mechanical effects using the Self-Consistent model. Reduction of channel thickness and adding doping impurities cause an increase in the threshold voltage. Moreover, the temperature effects cause a significant amount of threshold voltage shift. The temperature dependence of threshold voltage has also been observed with Self- Consistent approach which are well supported from experimental performance of practical devices.
Abstract: The present paper presents a finite element model and
analysis for the interaction between a piezoresistive tactile sensor and
biological tissues. The tactile sensor is proposed for use in minimally
invasive surgery to deliver tactile information of biological tissues to
surgeons. The proposed sensor measures the relative hardness of soft
contact objects as well as the contact force. Silicone rubbers were
used as the phantom of biological tissues. Finite element analysis of
the silicone rubbers and the mechanical structure of the sensor were
performed using COMSOL Multiphysics (v3.4) environment. The
simulation results verify the capability of the sensor to be used to
differentiate between different kinds of silicone rubber materials.
Abstract: The technical realization of data transmission using
glass fiber began after the development of diode laser in year 1962.
The erbium doped fiber amplifiers (EDFA's) in high speed networks
allow information to be transmitted over longer distances without
using of signal amplification repeaters. These kinds of fibers are
doped with erbium atoms which have energy levels in its atomic
structure for amplifying light at 1550nm. When a carried signal wave
at 1550nm enters the erbium fiber, the light stimulates the excited
erbium atoms which pumped with laser beam at 980nm as additional
light. The wavelength and intensity of the semiconductor lasers
depend on the temperature of active zone and the injection current.
The present paper shows the effect of the diode lasers temperature
and injection current on the optical amplification. From the results of
in- and output power one may calculate the max. optical gain by
erbium doped fiber amplifier.
Abstract: This paper presents the experimental results of silicone rubber polymer insulators for 22 kV systems under salt water dip wheel test based on IEC 62217. Straight shed silicone rubber polymer insulators having leakage distance 685 mm were tested continuously 30,000 cycles. One test cycle includes 4 positions, energized, de-energized, salt water dip and deenergized, respectively. For one test cycle, each test specimen remains stationary for about 40 second in each position and takes 8 second for rotate to next position. By visual observation, sever surface erosion was observed on the trunk near the energized end of tested specimen. Puncture was observed on the upper shed near the energized end. In addition, decreasing in hydrophobicity and increasing in hardness were measured on tested specimen comparing with new specimen. Furthermore, chemical analysis by ATR-FTIR was conducted in order to elucidate the chemical change of tested specimens comparing with new specimen.
Abstract: Ultrathin (UTD) and Nanoscale (NSD) SOI-MOSFET devices, sharing a similar W/L but with a channel thickness of 46nm and 1.6nm respectively, were fabricated using a selective “gate recessed” process on the same silicon wafer. The electrical transport characterization at room temperature has shown a large difference between the two kinds of devices and has been interpreted in terms of a huge unexpected series resistance. Electrical characteristics of the Nanoscale device, taken in the linear region, can be analytically derived from the ultrathin device ones. A comparison of the structure and composition of the layers, using advanced techniques such as Focused Ion Beam (FIB) and High Resolution TEM (HRTEM) coupled with Energy Dispersive X-ray Spectroscopy (EDS), contributes an explanation as to the difference of transport between the devices.