Abstract: In this paper we investigate the electrical
characteristics of a new structure of gate all around strained silicon
nanowire field effect transistors (FETs) with dual dielectrics by
changing the radius (RSiGe) of silicon-germanium (SiGe) wire and
gate dielectric. Indeed the effect of high-κ dielectric on Field Induced
Barrier Lowering (FIBL) has been studied. Due to the higher electron
mobility in tensile strained silicon, the n-type FETs with strained
silicon channel have better drain current compare with the pure Si
one. In this structure gate dielectric divided in two parts, we have
used high-κ dielectric near the source and low-κ dielectric near the
drain to reduce the short channel effects. By this structure short
channel effects such as FIBL will be reduced indeed by increasing
the RSiGe, ID-VD characteristics will be improved. The leakage
current and transfer characteristics, the threshold-voltage (Vt), the
drain induced barrier height lowering (DIBL), are estimated with
respect to, gate bias (VG), RSiGe and different gate dielectrics. For
short channel effects, such as DIBL, gate all around strained silicon
nanowire FET have similar characteristics with the pure Si one while
dual dielectrics can improve short channel effects in this structure.
Abstract: Bluetooth is a personal wireless communication
technology and is being applied in many scenarios. It is an emerging
standard for short range, low cost, low power wireless access
technology. Current existing MAC (Medium Access Control)
scheduling schemes only provide best-effort service for all masterslave
connections. It is very challenging to provide QoS (Quality of
Service) support for different connections due to the feature of
Master Driven TDD (Time Division Duplex). However, there is no
solution available to support both delay and bandwidth guarantees
required by real time applications. This paper addresses the issue of
how to enhance QoS support in a Bluetooth piconet. The Bluetooth
specification proposes a Round Robin scheduler as possible solution
for scheduling the transmissions in a Bluetooth Piconet. We propose
an algorithm which will reduce the bandwidth waste and enhance the
efficiency of network. We define token counters to estimate traffic of
real-time slaves. To increase bandwidth utilization, a back-off
mechanism is then presented for best-effort slaves to decrease the
frequency of polling idle slaves. Simulation results demonstrate that
our scheme achieves better performance over the Round Robin
scheduling.
Abstract: An area-integrating method that uses the technique of total integrated light scatter for evaluating the root mean square height of the surface Sq has been presented in the paper. It is based on the measurement of the scatter power using a flat photodiode integrator rather than an optical sphere or a hemisphere. By this means, one can obtain much less expensive and smaller instruments than traditional ones. Thanks to this, they could find their application for surface control purposes, particularly in small and medium size enterprises. A description of the functioning of the measuring unit as well as the impact caused by different factors on its properties is presented first. Next, results of measurements of the Sq values performed for optical, silicon and metal samples have been shown. It has been also proven that they are in a good agreement with the results obtained using the Ulbricht sphere instrument.
Abstract: The photoluminescence (PL) at 1.55 μm from
semiconducting β-FeSi2 has attracted a noticeable interest for
silicon-based optoelectronic applications. Moreover, its high optical
absorption coefficient (higher than 105 cm-1 above 1.0 eV) allows this
semiconducting material to be used as photovoltanics devices.
A clear PL spectrum for β-FeSi2 was observed by Cu or Au coating
on Si(001). High-crystal-quality β-FeSi2 with a low-level nonradiative
center was formed on a Cu- or Au- reated Si layer. This method of
deposition can be applied to other materials requiring high crystal
quality.
Abstract: Continuous-time delta-sigma analog digital converter (ADC) for radio frequency identification (RFID) complementary metal oxide semiconductor (CMOS) biosensor has been reported. This delta-sigma ADC is suitable for digital conversion of biosensor signal because of small process variation, and variable input range. As the input range of continuous-time switched current delta-sigma ADC (Dynamic range : 50 dB) can be limited by using current reference, amplification of biosensor signal is unnecessary. The input range is switched to wide input range mode or narrow input range mode by command of current reference. When the narrow input range mode, the input range becomes ± 0.8 V. The measured power consumption is 5 mW and chip area is 0.31 mm^2 using 1.2 um standard CMOS process. Additionally, automatic input range detecting system is proposed because of RFID biosensor applications.
Abstract: Herein, the organic semiconductor methyl orange
(MO), is investigated for the first time for its electronic applications.
For this purpose, Al/MO/n-Si heterojunction is fabricated through
economical cheap and simple “drop casting” technique. The currentvoltage
(I-V) measurements of the device are made at room
temperature under dark conditions. The I-V characteristics of
Al/MO/n-Si junction exhibits asymmetrical and rectifying behavior
that confirms the formation of diode. The diode parameters such as
rectification ratio (RR), turn on voltage (Vturn on), reverse saturation
current (I0), ideality factor (n), barrier height ( b
f ), series resistance
(Rs) and shunt resistance (Rsh) are determined from I-V curves using
Schottky equations. These values of these parameters are also
extracted and verified by applying Cheung’s functions. The
conduction mechanisms are explained from the forward bias I-V
characteristics using the power law.
Abstract: The effect of the number of quantum dot (QD) layers
on the saturated gain of doped QD semiconductor optical amplifiers
(SOAs) has been studied using multi-population coupled rate
equations. The developed model takes into account the effect of
carrier coupling between adjacent layers. It has been found that
increasing the number of QD layers (K) increases the unsaturated
optical gain for K
Abstract: In contrast to existing methods which do not take into account multiconnectivity in a broad sense of this term, we develop mathematical models and highly effective combination (BIEM and FDM) numerical methods of calculation of stationary and quasistationary temperature field of a profile part of a blade with convective cooling (from the point of view of realization on PC). The theoretical substantiation of these methods is proved by appropriate theorems. For it, converging quadrature processes have been developed and the estimations of errors in the terms of A.Ziqmound continuity modules have been received. For visualization of profiles are used: the method of the least squares with automatic conjecture, device spline, smooth replenishment and neural nets. Boundary conditions of heat exchange are determined from the solution of the corresponding integral equations and empirical relationships. The reliability of designed methods is proved by calculation and experimental investigations heat and hydraulic characteristics of the gas turbine first stage nozzle blade.
Abstract: Rotating stages in semiconductor, display industry and many other fields require challenging accuracy to perform their functions properly. Especially, Axis of rotation error on rotary system is significant; such as the spindle error motion of the aligner, wire bonder and inspector machine which result in the poor state of manufactured goods. To evaluate and improve the performance of such precision rotary stage, unessential movements on the other 5 degrees of freedom of the rotary stage must be measured and analyzed. In this paper, we have measured the three translations and two tilt motions of a rotating stage with high precision capacitive sensors. To obtain the radial error motion from T.I.R (Total Indicated Reading) of radial direction, we have used Donaldson's reversal technique. And the axial components of the spindle tilt error motion can be obtained accurately from the axial direction outputs of sensors by Estler face motion reversal technique. Further more we have defined and measured the sensitivity of positioning error to the five error motions.
Abstract: Future astronomical projects on large space x-ray
imaging telescopes require novel substrates and technologies for the
construction of their reflecting mirrors. The mirrors must be
lightweight and precisely shaped to achieve large collecting area with
high angular resolution. The new materials and technologies must be
cost-effective. Currently, the most promising materials are glass or
silicon foils. We focused on precise shaping these foils by thermal
forming process. We studied free and forced slumping in the
temperature region of hot plastic deformation and compared the
shapes obtained by the different slumping processes. We measured
the shapes and the surface quality of the foils. In the experiments, we
varied both heat-treatment temperature and time following our
experiment design. The obtained data and relations we can use for
modeling and optimizing the thermal forming procedure.
Abstract: In contrast to existing methods which do not take into account multiconnectivity in a broad sense of this term, we develop mathematical models and highly effective combination (BIEM and FDM) numerical methods of calculation of stationary and quasi-stationary temperature field of a profile part of a blade with convective cooling (from the point of view of realization on PC). The theoretical substantiation of these methods is proved by appropriate theorems. For it, converging quadrature processes have been developed and the estimations of errors in the terms of A.Ziqmound continuity modules have been received. For visualization of profiles are used: the method of the least squares with automatic conjecture, device spline, smooth replenishment and neural nets. Boundary conditions of heat exchange are determined from the solution of the corresponding integral equations and empirical relationships. The reliability of designed methods is proved by calculation and experimental investigations heat and hydraulic characteristics of the gas turbine first stage nozzle blade.
Abstract: Electron multiplying charge coupled devices (EMCCDs) have revolutionized the world of low light imaging by introducing on-chip multiplication gain based on the impact ionization effect in the silicon. They combine the sub-electron readout noise with high frame rates. Signal-to-noise Ratio (SNR) is an important performance parameter for low-light-level imaging systems. This work investigates the SNR performance of an EMCCD operated in Non-inverted Mode (NIMO) and Inverted Mode (IMO). The theory of noise characteristics and operation modes is presented. The results show that the SNR of is determined by dark current and clock induced charge at high gain level. The optimum SNR performance is provided by an EMCCD operated in NIMO in short exposure and strong cooling applications. In contrast, an IMO EMCCD is preferable.
Abstract: We propose an all optical flip-flop circuit composedof two Silicon-on-insulator microring resonators coupled to straightwaveguides by exploiting the optical bistability behavior due to thenonlinear Kerr effect. We used the transfer matrix analysis toinvestigate continuous wave propagation through microrings, as wellwe considered the nonlinear switching characteristics of an opticaldevice using a double-coupler silicon ring resonator in presence ofthe Kerr nonlinearity, thus obtaining the bistability behavior of theoutput port, the drop port and also inside the silicon microringresonator. It is shown that the bistability behavior depends on thecontrol of the input wavelength.KeywordsAll optical flip-flops, Kerr effect, microringresonator, optical bistability.
Abstract: The present work deals with the calculation of
transport properties of Hg0.8Cd0.2Te (MCT) semiconductor in
degenerate case. Due to their energy-band structure, this material
becomes degenerate at moderate doping densities, which are around
1015 cm-3, so that the usual Maxwell-Boltzmann approximation is
inaccurate in the determination of transport parameters. This problem
is faced by using Fermi-Dirac (F-D) statistics, and the non-parabolic
behavior of the bands may be approximated by the Kane model. The
Monte Carlo (MC) simulation is used here to determinate transport
parameters: drift velocity, mean energy and drift mobility versus
electric field and the doped densities. The obtained results are in
good agreement with those extracted from literature.
Abstract: In this study, the use of silicon NAM (Non-Audible
Murmur) microphone in automatic speech recognition is presented.
NAM microphones are special acoustic sensors, which are attached
behind the talker-s ear and can capture not only normal (audible)
speech, but also very quietly uttered speech (non-audible murmur).
As a result, NAM microphones can be applied in automatic speech
recognition systems when privacy is desired in human-machine communication.
Moreover, NAM microphones show robustness against
noise and they might be used in special systems (speech recognition,
speech conversion etc.) for sound-impaired people. Using a small
amount of training data and adaptation approaches, 93.9% word
accuracy was achieved for a 20k Japanese vocabulary dictation
task. Non-audible murmur recognition in noisy environments is also
investigated. In this study, further analysis of the NAM speech has
been made using distance measures between hidden Markov model
(HMM) pairs. It has been shown the reduced spectral space of NAM
speech using a metric distance, however the location of the different
phonemes of NAM are similar to the location of the phonemes
of normal speech, and the NAM sounds are well discriminated.
Promising results in using nonlinear features are also introduced,
especially under noisy conditions.
Abstract: We report here structural, mechanical and I-V
characteristics of Zn1-xMxO ceramic samples with various x and M.
It is found that the considered dopants does not influence the wellknown
peaks related to wurtzite structure of ZnO ceramics, while the
shape and size of grains are clearly affected. Average crystalline
diameters, deduced from XRD are between 42 nm and 54 nm, which
are 70 times lower than those obtained from SEM micrographs.
Interestingly, the potential barrier could be formed by adding Cu up
to 0.20, and it is completely deformed by 0.025 Ni additions. The
breakdown field could be enhanced up to 4138 V/cm by 0.025 Cu
additions, followed by a decrease with further increase of Cu . On
the other hand a gradual decrease in VHN is reported for both
dopants and their values are higher in Ni samples as compared to Cu
samples. The electrical conductivity is generally improved by Ni,
while addition of Cu improved it only in the over doped region (≥
0.10). These results are discussed in terms of the difference of
valency and ferromagnetic ordering for both dopants as compared to
undoped sample.
Abstract: In recent times there has been a growing interest in the
development of quasi-two-dimensional niobium pentoxide (Nb2O5)
as a semiconductor for the potential electronic applications such as
capacitors, filtration, dye-sensitised solar cells and gas sensing
platforms. Therefore once the purpose is established, Nb2O5 can be
prepared in a number of nano- and sub-micron-structural
morphologies that include rods, wires, belts and tubes. In this study
films of Nb2O5 were prepared on gold plated silicon substrate using
spin-coating technique and subsequently by mechanical exfoliation.
The reason this method was employed was to achieve layers of less
than 15nm in thickness. The sintering temperature of the specimen
was 800oC. The morphology and structural characteristics of the
films were analyzed by Atomic Force Microscopy (AFM), Raman
Spectroscopy, X-ray Photoelectron Spectroscopy (XPS).
Abstract: Adjacent Hall microsensors, comprising a silicon
substrate and four contacts, providing simultaneously two supply inputs and two differential outputs, are characterized. The voltage
related sensitivity is in the order of 0.11T-1, and a cancellation method for offset compensation is used, achieving residual offset in
the micro scale which is also compared to a single Hall plate.
Abstract: Silicon nanowire (SiNW) based thermoelectric device (TED) has potential applications in areas such as chip level cooling/ energy harvesting. It is a great challenge however, to assemble an efficient device with these SiNW. The presence of parasitic in the form of interfacial electrical resistance will have a significant impact on the performance of the TED. In this work, we explore the effect of the electrical contact resistance on the performance of a TED. Numerical simulations are performed on SiNW to investigate such effects on its cooling performance. Intrinsically, SiNW individually without the unwanted parasitic effect has excellent cooling power density. However, the cooling effect is undermined with the contribution of the electrical contact resistance.
Abstract: This paper discusses the Urdu script characteristics,
Urdu Nastaleeq and a simple but a novel and robust technique to
recognize the printed Urdu script without a lexicon. Urdu being a
family of Arabic script is cursive and complex script in its nature, the
main complexity of Urdu compound/connected text is not its
connections but the forms/shapes the characters change when it is
placed at initial, middle or at the end of a word. The characters
recognition technique presented here is using the inherited
complexity of Urdu script to solve the problem. A word is scanned
and analyzed for the level of its complexity, the point where the level
of complexity changes is marked for a character, segmented and
feeded to Neural Networks. A prototype of the system has been
tested on Urdu text and currently achieves 93.4% accuracy on the
average.