Abstract: The levels of maximum power density of GSM
signals in the cities of Lagos, Ibadan and Abuja were studied.
Measurements were made with a calibrated hand held spectrum
analyzer 200m away from 271 base stations, at 1.2m to the ground
level. The maximum GSM 900 signal power density was
139.63μW/m2 in Lagos, 162.49μW/m2 in Ibadan and 5411.26μW/m2
in Abuja. Also, the maximum GSM 1800 signal power density was
296.82μW/m2 in Lagos, 116.82μW/m2 in Ibadan and 1263.00μW/m2
in Abuja. The level of power density of GSM 900 and GSM 1800
signals in the cities of Lagos, Ibadan and Abuja are far less than the
recommended value of 4.5W/m2 for GSM 900 and 9.0 W/m2 for
GSM 1800 by the ICNRP guideline. It can be concluded that
exposure to GSM signals in these cities cannot contribute to the
health detriments caused by thermal effects of radiofrequency
radiation.
Abstract: Carbon nanotube is one of the most attractive materials
for the potential applications of nanotechnology due to its excellent
mechanical, thermal, electrical and optical properties. In this paper we
report a supercapacitor made of nickel foil electrodes, coated with
multiwall carbon nanotubes (MWCNTs) thin film using
electrophoretic deposition (EPD) method. Chemical vapor deposition
method was used for the growth of MWCNTs and ethanol was used as
a hydrocarbon source. High graphitic multiwall carbon nanotube was
found at 750oC analyzing by Raman spectroscopy. We observed the
electrochemical performance of supercapacitor by cyclic
voltammetry. The electrodes of supercapacitor fabricated from
MWCNTs exhibit considerably small equivalent series resistance
(ESR), and a high specific power density. Electrophoretic deposition
is an easy method in fabricating MWCNT electrodes for high
performance supercapacitor.
Abstract: Non-destructive testing and evaluation techniques for
assessing the integrity of composite structures are essential to both
reduce manufacturing costs and out of service time of transport means
due to maintenance. In this study, Analyze into non-destructive test
characterization of carbon fiber reinforced plastics (CFRP) internal
and external defects using thermo-graphic camera and transient
thermography method. non-destructive testing were characterized by
defect size (Ø8, Ø10, Ø12, Ø14) and depth (1.2mm, 2.4mm).
Abstract: Brown seaweeds are abundant in Portuguese coastline
and represent an almost unexploited marine economic resource. One
of the most common species, easily available for harvesting in the
northwest coast, is Saccorhiza polyschides grows in the lowest shore
and costal rocky reefs. It is almost exclusively used by local farmers
as natural fertilizer, but contains a substantial amount of valuable
compounds, particularly alginates, natural biopolymers of high
interest for many industrial applications.
Alginates are natural polysaccharides present in cell walls of
brown seaweed, highly biocompatible, with particular properties that
make them of high interest for the food, biotechnology, cosmetics
and pharmaceutical industries. Conventional extraction processes are
based on thermal treatment. They are lengthy and consume high
amounts of energy and solvents. In recent years, microwave-assisted
extraction (MAE) has shown enormous potential to overcome major
drawbacks that outcome from conventional plant material extraction
(thermal and/or solvent based) techniques, being also successfully
applied to the extraction of agar, fucoidans and alginates. In the
present study, acid pretreatment of brown seaweed Saccorhiza
polyschides for subsequent microwave-assisted extraction (MAE) of
alginate was optimized. Seaweeds were collected in Northwest
Portuguese coastal waters of the Atlantic Ocean between May and
August, 2014. Experimental design was used to assess the effect of
temperature and acid pretreatment time in alginate extraction.
Response surface methodology allowed the determination of the
optimum MAE conditions: 40 mL of HCl 0.1 M per g of dried
seaweed with constant stirring at 20ºC during 14h. Optimal acid
pretreatment conditions have enhanced significantly MAE of
alginates from Saccorhiza polyschides, thus contributing for the
development of a viable, more environmental friendly alternative to
conventional processes.
Abstract: In this study, epoxy composite specimens reinforced
with multi-walled carbon nanotube filler were fabricated using shear
mixer and ultra-sonication processor. The mechanical and thermal
properties of the fabricated specimens were measured and evaluated.
From the electron microscope images and the results from the
measurements of tensile strengths, the specimens having 0.6 wt%
nanotube content show better dispersion and higher strength than those
of the other specimens. The Young’s moduli of the specimens
increased as the contents of the nanotube filler in the matrix were
increased. The specimen having a 0.6 wt% nanotube filler content
showed higher thermal conductivity than that of the other specimens.
While, in the measurement of thermal expansion, specimens having
0.4 and 0.6 wt% filler contents showed a lower value of thermal
expansion than that of the other specimens. On the basis of the
measured and evaluated properties of the composites, we believe that
the simple and time-saving fabrication process used in this study was
sufficient to obtain improved properties of the specimens.
Abstract: PVC foam-fly ash composites (PVC-FA) are
characterized for their structural, morphological, mechanical and
thermal properties. The tensile strength of the composites increased
modestly with higher fly ash loading, while there was a significant
increase in the elastic modulus for the same composites. On the other
hand, a decrease in elongation at UTS was observed upon increasing
fly ash content due to increased rigidity of the composites. Similarly,
the flexural modulus increased as the fly ash loading increased,
where the composites containing 25 phr fly ash showed the highest
flexural strength. Thermal properties of PVC-fly ash composites were
determined by Thermo Gravimetric Analysis (TGA). The
microstructural properties were studied by Scanning Electron
Microscopy (SEM). SEM results confirm that fly ash particles were
mechanically interlocked in PVC matrix with good interfacial
interaction with the matrix. Particle agglomeration and debonding
was observed in samples containing higher amounts of fly ash.
Abstract: Two types of glass fibers having different lengths
(1/16" and 1/32") were added into rigid PVC foams to enhance the
dimensional stability of extruded rigid Polyvinyl Chloride (PVC)
foam at different concentrations (0-20 phr) using a single screw
profile extruder. PVC foam-glass fiber composites (PVC-GF) were
characterized for their dimensional stability, structural, thermal, and
mechanical properties. Experimental results show that the
dimensional stability, heat resistance, and storage modulus were
enhanced without compromising the tensile and flexural strengths of
the composites. Overall, foam composites which were prepared with
longer glass fibers exhibit better mechanical and thermal properties
than those prepared with shorter glass fibers due to higher
interlocking between the fibers and the foam cells, which result in
better load distribution in the matrix.
Abstract: To practically apply vacuum insulation panels (VIPs)
to buildings or home appliances, VIPs have demanded long-term
lifespan with outstanding insulation performance. Service lives of
VIPs enveloped with Al-foil and three-layer Al-metallized envelope
are calculated. For Al-foil envelope, the service life is longer but edge
conduction is too large compared with the Al-metallized envelope. To
increase service life even more, the proposed double enveloping
method and metal-barrier-added enveloping method are further
analyzed. The service lives of the VIP to employ two enveloping
methods are calculated. Also, pressure increase and thermal insulation
performance characteristics are investigated. For the metalbarrier-
added enveloping method, effective thermal conductivity
increase with time is close to that of Al-foil envelope, especially, for
getter-inserted VIPs. For double enveloping method, if water vapor is
perfectly adsorbed, the effect of service life enhancement becomes
much greater. From these methods, the VIP can be guaranteed for
service life of more than 20 years.
Abstract: Particles are the most common and cheapest
reinforcement producing discontinuous reinforced composites with
isotropic properties. Conventional fabrication methods can be used to
produce a wide range of product forms, making them relatively
inexpensive. Optimising composite development must include
consideration of all the fundamental aspect of particles including
their size, shape, volume fraction, distribution and mechanical
properties. Research has shown that the challenges of low fracture
toughness, poor crack growth resistance and low thermal stability can
be overcome by reinforcement with particles. The unique properties
exhibited by micro particles reinforced ceramic composites have
made them to be highly attractive in a vast array of applications.
Abstract: According to the demand of the power and
refrigeration industry, the theoretical and practical teachings of the
Thermal Energy and Power Engineering characteristic specialty in
china are studied. The teaching reform and practice of the Thermal
Energy and Power Engineering specialty have been carried out,
including construction and reform measures, teaching reform and
practice, features, and achievements. Proved by practices, the
theoretical and practical teaching effects are obvious. The study results
can provides certain reference experience for theoretical and practical
teachings of the related specialties in china.
Abstract: It is usually difficult for students to understand some
basic theories in learning thermal energy and power engineering
course. A new teaching method was proposed that we should introduce
the comparison research method of those theories to help them being
understood. “Homogeneous and heterogeneous catalysis” teaching is
analyzed as an example by comparison research method.
Abstract: This article is deal with the experimental
investigations of the laser diode matrixes (LDM) based on the
AlGaAs/GaAs heterostructures (lasing wavelength 790-880 nm) to
find optimal LDM parameters for active vision systems. In particular,
the dependence of LDM radiation pulse power on the pulse duration
and LDA active layer heating as well as the LDM radiation
divergence are discussed.
Abstract: Vacuum Insulation Panel (VIP) can achieve very low
thermal conductivity by evacuating its inner space. Heat transfer in the
core materials of highly-evacuated VIP occurs by conduction through
the solid structure and radiation through the pore. The effect of various
scattering modes in combined conduction-radiation in VIP is
investigated through numerical analysis. The discrete ordinates
interpolation method (DOIM) incorporated with the commercial code
FLUENT® is employed. It is found that backward scattering is more
effective in reducing the total heat transfer while isotropic scattering is
almost identical with pure absorbing/emitting case of the same optical
thickness. For a purely scattering medium, the results agrees well with
additive solution with diffusion approximation, while a modified term
is added in the effect of optical thickness to backward scattering is
employed. For other scattering phase functions, it is also confirmed
that backwardly scattering phase function gives a lower effective
thermal conductivity. Thus the materials with backward scattering
properties, with radiation shields are desirable to lower the thermal
conductivity of VIPs.
Abstract: Vacuum insulation panel (VIP) is a promising thermal
insulator for buildings, refrigerator, LNG carrier and so on. In general,
it has the thermal conductivity of 2~4 mW/m·K. However, this thermal
conductivity is that measured at the center of VIP. The total effective
thermal conductivity of VIP is larger than this value due to the edge
conduction through the envelope. In this paper, the edge conduction of
VIP is examined theoretically, numerically and experimentally. To
confirm the existence of the edge conduction, numerical analysis is
performed for simple two-dimensional VIP model and a theoretical
model is proposed to calculate the edge conductivity. Also, the edge
conductivity is measured using the vacuum guarded hot plate and the
experiment is validated against numerical analysis. The results show
that the edge conductivity is dependent on the width of panel and
thickness of Al-foil. To reduce the edge conduction, it is recommended
that the VIP should be made as big as possible or made of thin Al film
envelope.
Abstract: This paper illustrates the effect of nano Magnesium
Hydroxide (MH) loading on the thermal properties of Low Density
Polyethylene (LDPE)/Poly (ethylene-co vinyl acetate) (EVA) nano
composite. Thermal studies were conducted, as it understanding is
vital for preliminary development of new polymeric systems.
Thermal analysis of nanocomposite was conducted using thermo
gravimetric analysis (TGA), and differential scanning calorimetry
(DSC). Major finding of TGA indicated two main stages of
degradation process found at (350 ± 25oC) and (480 ± 25oC)
respectively. Nano metal filler expressed better fire resistance as it
stand over high degree of temperature. Furthermore, DSC analysis
provided a stable glass temperature around 51 (±1oC) and captured
double melting point at 84 (±2oC) and 108 (±2oC). This binary
melting point reflects the modification of nano filler to the polymer
matrix forming melting crystals of folded and extended chain. The
percent crystallinity of the samples grew vividly with increasing filler
content. Overall, increasing the filler loading improved the
degradation temperature and weight loss evidently and a better
process and phase stability was captured in DSC.
Abstract: This paper reveals the interaction between hydrogen
and surface stress in austenitic stainless steel by X-ray diffraction
stress measurement and thermal desorption analysis before and after
being charged with hydrogen. The surface residual stress was varied
by surface finishing using several disc polishing agents. The obtained
results show that the residual stress near surface had a significant
effect on hydrogen absorption behavior, that is, tensile residual stress
promoted the hydrogen absorption and compressive one did opposite.
Also, hydrogen induced equi-biaxial stress and this stress has a linear
correlation with hydrogen content.
Abstract: Nitrogen-doped graphene quantum dots (N-GQDs)
were fabricated by microwave-assisted hydrothermal technique. The
optical properties of the N-GQDs were studied. The luminescence of
the N-GQDs can be tuned by varying the excitation wavelength.
Furthermore, two-photon luminescence of the N-GQDs excited by
near-infrared laser can be obtained. It is shown that N-doping play a
key role on two-photon luminescence. The N-GQDs are expected to
find application in biological applications including bioimaging and
sensing.
Abstract: This paper represents performance of particle swarm
optimisation (PSO) algorithm based integral (I) controller and
proportional-integral controller (PI) for interconnected hydro-thermal
automatic generation control (AGC) with generation rate constraint
(GRC) and Thyristor controlled phase shifter (TCPS) in series with
tie line. The control strategy of TCPS provides active control of
system frequency. Conventional objective function integral square
error (ISE) and another objective function considering square of
derivative of change in frequencies of both areas and change in tie
line power are considered. The aim of designing the objective
function is to suppress oscillation in frequency deviations and change
in tie line power oscillation. The controller parameters are searched
by PSO algorithm by minimising the objective functions. The
dynamic performance of the controllers I and PI, for both the
objective functions, are compared with conventionally optimized I
controller.
Abstract: This paper reports the numerical and experimental
performances of Double Glass Wall are investigated. Two
configurations were considered namely, the Double Clear Glass Wall
(DCGW) and the Double Translucent Glass Wall (DTGW). The
coupled governing equations as well as boundary conditions are
solved using the finite element method (FEM) via COMSOLTM
Multiphysics. Temperature profiles and flow field of the DCGW and
DTGW are reported and discussed. Different constant heat fluxes
were considered as 400 and 800 W.m-2 the corresponding initial
condition temperatures were 30.5 and 38.5ºC respectively. The
results show that the simulation results are in agreement with the
experimental data. Conclusively, the model considered in this study
could reasonable be used simulate the thermal and ventilation
performance of the DCGW and DTGW configurations.
Abstract: In this research article a comprehensive investigation
has been carried out to determine the effect of thermal cycle on
temperature dependent process parameters developed during gas
tungsten arc (GTA) welding of high carbon (AISI 1090) steel butt
joints. An experiment based thermal analysis has been performed to
obtain the thermal history. We have focused on different
thermophysical properties such as thermal conductivity, heat transfer
coefficient and cooling rate. Angular torch model has been utilized to
find out the surface heat flux and its variation along the fusion zone as
well as along the longitudinal direction from fusion boundary. After
welding and formation of weld pool, heat transfer coefficient varies
rapidly in the vicinity of molten weld bead and heat affected zone. To
evaluate the heat transfer coefficient near the fusion line and near the
rear end of the plate (low temperature region), established correlation
has been implemented and has been compared with empirical
correlation which is noted as coupled convective and radiation heat
transfer coefficient. Change in thermal conductivity has been
visualized by analytical model of moving point heat source. Rate of
cooling has been estimated by using 2-dimensional mathematical
expression of cooling rate and it has shown good agreement with
experimental temperature cycle. Thermophysical properties have been
varied randomly within 0 -10s time span.