Abstract: Catalytic combustion of methane is imperative due to
stability of methane at low temperature. Methane (CH4), therefore,
remains unconverted in vehicle exhausts thereby causing greenhouse
gas GHG emission problem. In this study, heterogeneous catalysts of
palladium with bio-char (2 wt% Pd/Bc) and Al2O3 (2wt% Pd/ Al2O3)
supports were prepared by incipient wetness impregnation and then
subsequently tested for catalytic combustion of CH4. Support-porous
heterogeneous catalytic combustion (HCC) material were selected
based on factors such as surface area, porosity, thermal stability,
thermal conductivity, reactivity with reactants or products, chemical
stability, catalytic activity, and catalyst life. Sustainable and
renewable support-material of bio-mass char derived from palm shell
waste material was compared with those from the conventional
support-porous materials. Kinetic rate of reaction was determined for
combustion of methane on Palladium (Pd) based catalyst with Al2O3
support and bio-char (Bc). Material characterization was done using
TGA, SEM, and BET surface area. The performance test was
accomplished using tubular quartz reactor with gas mixture ratio of
3% methane and 97% air. The methane porous-HCC conversion was
carried out using online gas analyzer connected to the reactor that
performed porous-HCC. BET surface area for prepared 2 wt% Pd/Bc
is smaller than prepared 2wt% Pd/ Al2O3 due to its low porosity
between particles. The order of catalyst activity based on kinetic rate
on reaction of catalysts in low temperature was 2wt%
Pd/Bc>calcined 2wt% Pd/ Al2O3> 2wt% Pd/ Al2O3>calcined 2wt%
Pd/Bc. Hence agro waste material can successfully be utilized as an
inexpensive catalyst support material for enhanced CH4 catalytic
combustion.
Abstract: Using the pseudopotential technique the Sagdeev
potential equation has been derived in a plasma consisting of twotemperature
nonisothermal electrons, negatively charged dust grains
and warm positive ions. The study shows that the presence of
nonisothermal two-temperature electrons and charged dust grains
have significant effects on the excitation and structure of the ionacoustic
double layers in the model plasma under consideration. Only
compressive type double layer is obtained in the present plasma
model. The double layer solution has also been obtained by including
higher order nonlinearity and nonisothermality, which is shown to
modify the amplitude and deform the shape of the double layer.
Abstract: In the present work, fly ash geopolymer based
composites including polyester (PES) waste were studied. Specimens
of three compositions were prepared: (a) fly ash geopolymer with 5%
PES waste; (b) fly ash geopolymer mortar with 5% PES waste; (c) fly
ash geopolymer mortar with 6.25% PES waste. Compressive and
bending strength measurements, water absorption test and
determination of thermal conductivity coefficient were performed.
The results showed that the addition of sand in a mixture of
geopolymer with 5% PES content led to higher compressive strength,
while it increased water absorption and reduced thermal conductivity
coefficient. The increase of PES addition in geopolymer mortars
resulted in a more dense structure, indicated by the increase of
strength and thermal conductivity and the decrease of water
absorption.
Abstract: The thermal behavior of a large-scale, phase change material (PCM) enhanced building envelope system was studied in regard to the need for pre-fabricated construction in subtropical regions. The proposed large-scale envelope consists of a reinforced aluminum skin, insulation core, phase change material and reinforced gypsum board. The PCM impact on an energy efficiency of an enveloped room was resolved by validation of the EnergyPlus numerical scheme and optimization of a smart material location in the core. The PCM location was optimized by a minimization method of a cooling energy demand. It has been shown that there is good agreement between the test and simulation results. The optimal location of the PCM layer in Hong Kong summer conditions has been then recomputed for core thicknesses of 40, 60 and 80 mm. A non-dimensional value of the optimal PCM location was obtained to be same for all the studied cases and the considered external and internal conditions.
Abstract: In this paper, effects of using Alumina-water
nanofluid on the rate of heat transfer have been investigated
numerically. Physical model is a square enclosure with insulated top
and bottom horizontal walls, while the vertical walls are kept at
different constant temperatures. Two appropriate models are used to
evaluate the viscosity and thermal conductivity of nanofluid. The
governing stream-vorticity equations are solved using a second order
central finite difference scheme, coupled to the conservation of mass
and energy. The study has been carried out for the Richardson
number 0.1 to 10 and the solid volume fraction 0 to 0.04. Results are
presented by isotherms lines, average Nusselt number and normalized
Nusselt number in different range of φ and Ri for forced, combined
and natural convection dominated regime. It is found that higher heat
transfer rate is predicted when the effects of nanoparticle is taken into
account.
Abstract: Numerical studies were conducted using Lattice
Boltzmann Method (LBM) to study the natural convection in a square
cavity in the presence of roughness. An algorithm based on a single
relaxation time Bhatnagar-Gross-Krook (BGK) model of Lattice
Boltzmann Method (LBM) was developed. Roughness was
introduced on both the hot and cold walls in the form of sinusoidal
roughness elements. The study was conducted for a Newtonian fluid
of Prandtl number (Pr) 1.0. The range of Ra number was explored
from 10^3 to 10^6 in a laminar region. Thermal and hydrodynamic
behavior of fluid was analyzed using a differentially heated square
cavity with roughness elements present on both the hot and cold wall.
Neumann boundary conditions were introduced on horizontal walls
with vertical walls as isothermal. The roughness elements were at the
same boundary condition as corresponding walls. Computational
algorithm was validated against previous benchmark studies
performed with different numerical methods, and a good agreement
was found to exist. Results indicate that the maximum reduction in
the average heat transfer was 16.66 percent at Ra number 10^5.
Abstract: Activated carbons (M4P0, M4P2, and M5P2) used in
this research were produced from palm shell and polyetherether
ketone (PEEK) via carbonization, impregnation and microwave
activation. The adsorption/desorption process was carried out using
static volumetric adsorption. Regeneration is important in the overall
economy of the process and waste minimization. This work focuses
on the thermal regeneration of the CO2 exhausted microwave
activated carbons. The regeneration strategy adopted was thermal
with nitrogen purge desorption with N2 feed flow rate of 20 ml/min
for 1 h at atmospheric pressure followed by drying at 150oC.Seven
successive adsorption/regeneration processes were carried out on the
material. It was found that after seven adsorption regeneration cycles;
the regeneration efficiency (RE) for CO2 activated carbon from palm
shell only (M4P0) was more than 90% while that of hybrid palm
shell-PEEK (M4P2, M5P2) was above 95%. The cyclic adsorption
and regeneration shows the stability of the adsorbent materials.
Abstract: Poly vinyl acetate (PVA)-based titania (TiO2)–carbon
nanotube composite nanofibers (PVA-TCCNs) with various
PVA-to-solvent ratios and PVA-based TiO2 composite nanofibers
(PVA-TN) were synthesized using an electrospinning process,
followed by thermal treatment. The photocatalytic activities of these
nanofibers in the degradation of airborne monocyclic aromatics under
visible-light irradiation were examined. This study focuses on the
application of these photocatalysts to the degradation of the target
compounds at sub-part-per-million indoor air concentrations. The
characteristics of the photocatalysts were examined using scanning
electron microscopy, X-ray diffraction, ultraviolet-visible
spectroscopy, and Fourier-transform infrared spectroscopy. For all the
target compounds, the PVA-TCCNs showed photocatalytic
degradation efficiencies superior to those of the reference PVA-TN.
Specifically, the average photocatalytic degradation efficiencies for
benzene, toluene, ethyl benzene, and o-xylene (BTEX) obtained using
the PVA-TCCNs with a PVA-to-solvent ratio of 0.3 (PVA-TCCN-0.3)
were 11%, 59%, 89%, and 92%, respectively, whereas those observed
using PVA-TNs were 5%, 9%, 28%, and 32%, respectively.
PVA-TCCN-0.3 displayed the highest photocatalytic degradation
efficiency for BTEX, suggesting the presence of an optimal
PVA-to-solvent ratio for the synthesis of PVA-TCCNs. The average
photocatalytic efficiencies for BTEX decreased from 11% to 4%, 59%
to 18%, 89% to 37%, and 92% to 53%, respectively, when the flow
rate was increased from 1.0 to 4.0 L min1. In addition, the average
photocatalytic efficiencies for BTEX increased 11% to ~0%, 59% to
3%, 89% to 7%, and 92% to 13%, respectively, when the input
concentration increased from 0.1 to 1.0 ppm. The prepared
PVA-TCCNs were effective for the purification of airborne aromatics
at indoor concentration levels, particularly when the operating
conditions were optimized.
Abstract: Epidermal Growth Factor (EGF, Mw=6,045) has been
reported to have high efficiency of wound repair and anti-wrinkle
effect. However, the half-life of EGF in the body is too short to exert
the biological activity effectively when applied in free form. Growth
Factors can be stabilized by immobilization with carbohydrates from
thermal and proteolytic degradation. Low molecular weight chitosan
(LMCS) and its derivate prepared by hydrogen peroxide has high
solubility. LM6A6DC was successfully prepared as a reactive
carbohydrate for the stabilization of EGF by the reactions of LMCS
with alkalization, tosylation, azidation and reduction. The structure of
LM6A6DC was confirmed by FT-IR, 1H NMR and elementary
analysis. For enhancing the stability of free EGF, EGF was attached
with LM6A6DC by using water-soluble carbodiimide.
EGF-LM6A6DC conjugates did not show any cytotoxicity on the
Normal Human Dermal Fibroblast (NHDF) 3T3 proliferation at least
under 100 μg/ml. In the result, it was considered that LM6A6DC is
suitable to immobilize of growth factor.
Abstract: Part and parcel of building green homes (GHs) with
favorable thermal comfort (TC) is to design and build with reduced
carbon footprint (CF) from embodied energy in the building envelope
and reduced operational CF overall. Together, the environmental
impact of GHs can be reduced significantly. Nevertheless, there is
still a need to identify the base CF value for Malaysian GHs and this
can be done by assessing existing ones which can then be compared
to conventional and vernacular houses which are built differently
with different building materials. This paper underlines the research
design and introduces the case studies. For now, the operational CF
of the case studies is beyond the scope of this study. Findings from
this research could identify the best building material and
construction technique combination to build GHs depending on the
available skills, financial constraints and the condition of the
immediate environment.
Abstract: The turbocharger and turbocharging have been the
inherent component of diesel engines, so that critical parameters of
such engines, as BSFC (Brake Specific Fuel Consumption) or
thermal efficiency, fuel consumption, BMEP (Brake Mean Effective
Pressure), the power density output and emission level have been
improved extensively. In general, the turbocharger can be considered
as the most complex component of diesel engines, because it has
closely interrelated turbomachinery concepts of the turbines and the
compressors to thermodynamic fundamentals of internal combustion
engines and stress analysis of all components.
In this paper, a waste gate for a conventional single stage radial
turbine is investigated by consideration of turbochargers operation
constrains and engine operation conditions, without any detail
designs in the turbine and the compressor. Amount of opening waste
gate which extended between the ranges of full opened and closed
valve, is demonstrated by limiting compressor boost pressure ratio.
Obtaining of an optimum point by regard above mentioned items is
surveyed by three linked meanline modeling programs together
which consist of Turbomatch®, Compal®, Rital® madules in concepts
NREC® respectively.
Abstract: At present, the cascade PID control is widely used to
control the superheating temperature (main steam temperature). As
Main Steam Temperature has the characteristics of large inertia, large
time-delay and time varying, etc., conventional PID control strategy
cannot achieve good control performance. In order to overcome the
bad performance and deficiencies of main steam temperature control
system, Model Free Adaptive Control (MFAC) - P cascade control
system is proposed in this paper. By substituting MFAC in PID of the
main control loop of the main steam temperature control, it can
overcome time delays, non-linearity, disturbance and time variation.
Abstract: It has become an increasing evident that large
development influences the climate. There are concerns that rising
temperature over developed areas could have negative impact and
increase living discomfort within city boundaries. Temperature trends
in Ibadan city have received little attention, yet the area has
experienced heavy urban expansion between 1972 and 2014. This
research aims at examining the impact of landuse change on surface
temperature knowing that the built-up environment absorb and store
solar energy, resulting into the Urban Heat Island (UHI) effect. The
Landsat imagery was used to examine the landuse change for a
period of 42 years (1972-2014). Land Surface Temperature (LST)
was obtained by converting the thermal band to a surface temperature
map and zonal statistic analyses was used to examine the relationship
between landuse and temperature emission. The results showed that
the settlement area increased to a large extent while the area covered
by vegetation reduced during the study period. The spatial and
temporal trends of surface temperature are related to the gradual
change in urban landuse/landcover and the settlement area has the
highest emission. This research provides useful insight into the
temporal behavior of the Ibadan city.
Abstract: In this paper, an effective non-destructive, noninvasive
approach for leak detection was proposed. The process relies
on analyzing thermal images collected by an IR viewer device that
captures thermo-grams. In this study a statistical analysis of the
collected thermal images of the ground surface along the expected
leak location followed by a visual inspection of the thermo-grams
was performed in order to locate the leak. In order to verify the
applicability of the proposed approach the predicted leak location
from the developed approach was compared with the real leak
location. The results showed that the expected leak location was
successfully identified with an accuracy of more than 95%.
Abstract: Unmanned Aircraft Systems (UAS) become
indispensable parts of modern airpower as force multiplier. One of
the main advantages of UAS is long endurance. UAS have to take
extra payloads to accomplish different missions but these payloads
decrease endurance of aircraft because of increasing drag. There are
continuing researches to increase the capability of UAS. There are
some vertical thermal air currents, which can cause climb and
increase endurance, in nature. Birds and gliders use thermals to gain
altitude with no effort. UAS have wide wings which can use
thermals like birds and gliders. Thermal regions, which is area of
2000-3000 meter (1 NM), exist all around the world. It is natural and
infinite source. This study analyses if thermal regions can be adopted
and implemented as an assistant tool for UAS route planning. First
and second part of study will contain information about the thermal
regions and current applications about UAS in aviation and climbing
performance with a real example. Continuing parts will analyze the
contribution of thermal regions to UAS endurance. Contribution is
important because planning declaration of UAS navigation rules will
be in 2015.
Abstract: Organic Rankine Cycle (ORC) is the most commonly used method for recovering energy from small sources of heat. The investigation of the ORC in supercritical condition is a new research area as it has a potential to generate high power and thermal efficiency in a waste heat recovery system. This paper presents a steady state ORC model in supercritical condition and its simulations with a real engine’s exhaust data. The key component of ORC, evaporator, is modelled using finite volume method, modelling of all other components of the waste heat recovery system such as pump, expander and condenser are also presented. The aim of this paper is to investigate the effects of mass flow rate and evaporator outlet temperature on the efficiency of the waste heat recovery process. Additionally, the necessity of maintaining an optimum evaporator outlet temperature is also investigated. Simulation results show that modification of mass flow rate is the key to changing the operating temperature at the evaporator outlet.
Abstract: The borate glasses are known by their structural
characterized by existence of unit’s structural composed by triangles
and tetrahedrons boron in different configurations depending on the
percentage of B2O3 in the glass chemical composition. In this paper,
effect of lithium oxide addition on the thermal and physical
properties of an alumina borate glass, was investigated. It was found
that the boron abnormality has a significant effect in the change of
glass properties according to the addition rate of lithium oxide.
Abstract: Microbial fuel cells (MFCs) represent a promising
technology for simultaneous bioelectricity generation and wastewater
treatment. Catalysts are significant portions of the cost of microbial
fuel cell cathodes. Many materials have been tested as aqueous
cathodes, but air-cathodes are needed to avoid energy demands for
water aeration. The sluggish oxygen reduction reaction (ORR) rate at
air cathode necessitates efficient electrocatalyst such as carbon
supported platinum catalyst (Pt/C) which is very costly. Manganese
oxide (MnO2) was a representative metal oxide which has been
studied as a promising alternative electrocatalyst for ORR and has
been tested in air-cathode MFCs. However the single MnO2 has poor
electric conductivity and low stability. In the present work, the MnO2
catalyst has been modified by doping Pt nanoparticle. The goal of the
work was to improve the performance of the MFC with minimum Pt
loading. MnO2 and Pt nanoparticles were prepared by hydrothermal
and sol gel methods, respectively. Wet impregnation method was
used to synthesize Pt/MnO2 catalyst. The catalysts were further used
as cathode catalysts in air-cathode cubic MFCs, in which anaerobic
sludge was inoculated as biocatalysts and palm oil mill effluent
(POME) was used as the substrate in the anode chamber. The asprepared
Pt/MnO2 was characterized comprehensively through field
emission scanning electron microscope (FESEM), X-Ray diffraction
(XRD), X-ray photoelectron spectroscopy (XPS), and cyclic
voltammetry (CV) where its surface morphology, crystallinity,
oxidation state and electrochemical activity were examined,
respectively. XPS revealed Mn (IV) oxidation state and Pt (0)
nanoparticle metal, indicating the presence of MnO2 and Pt.
Morphology of Pt/MnO2 observed from FESEM shows that the
doping of Pt did not cause change in needle-like shape of MnO2
which provides large contacting surface area. The electrochemical
active area of the Pt/MnO2 catalysts has been increased from 276 to
617 m2/g with the increase in Pt loading from 0.2 to 0.8 wt%. The
CV results in O2 saturated neutral Na2SO4 solution showed that
MnO2 and Pt/MnO2 catalysts could catalyze ORR with different
catalytic activities. MFC with Pt/MnO2 (0.4 wt% Pt) as air cathode
catalyst generates a maximum power density of 165 mW/m3, which
is higher than that of MFC with MnO2 catalyst (95 mW/m3). The
open circuit voltage (OCV) of the MFC operated with MnO2 cathode
gradually decreased during 14 days of operation, whereas the MFC
with Pt/MnO2 cathode remained almost constant throughout the
operation suggesting the higher stability of the Pt/MnO2 catalyst.
Therefore, Pt/MnO2 with 0.4 wt% Pt successfully demonstrated as an
efficient and low cost electrocatalyst for ORR in air cathode MFC with higher electrochemical activity, stability and hence enhanced
performance.
Abstract: A numerical study of natural convection heat transfer
in water filled cavity has been examined in 3-Dfor single phase liquid
cooling system by using an array of parallel plate fins mounted to one
wall of a cavity. The heat generated by a heat source represents a
computer CPU with dimensions of 37.5∗37.5mm mounted on
substrate. A cold plate is used as a heat sink installed on the opposite
vertical end of the enclosure. The air flow inside the computer case is
created by an exhaust fan. A turbulent air flow is assumed and k-ε
model is applied. The fins are installed on the substrate to enhance
the heat transfer. The applied power energy range used is between 15
- 40W. In order to determine the thermal behaviour of the cooling
system, the effect of the heat input and the number of the parallel
plate fins are investigated. The results illustrate that as the fin number
increases the maximum heat source temperature decreases. However,
when the fin number increases to critical value the temperature start
to increase due to the fins are too closely spaced and that cause the
obstruction of water flow. The introduction of parallel plate fins
reduces the maximum heat source temperature by 10% compared to
the case without fins. The cooling system maintains the maximum
chip temperature at 64.68°C when the heat input was at 40W that is
much lower than the recommended computer chips limit temperature
of no more than 85°C and hence the performance of the CPU is
enhanced.
Abstract: In rapid industrial development, the demand for
high-strength and lightweight materials have been increased. Thus,
various CFRP (Carbon Fiber Reinforced Plastics) with composite
materials are being used. The design variables of CFRP are its
lamination direction, order and thickness. Thus, the hardness and
strength of CFRP depends much on their design variables. In this
paper, the lamination direction of CFRP was used to produce a
symmetrical ply [0°/0°, -15°/+15°, -30°/+30°, -45°/+45°, -60°/+60°,
-75°/+75° and 90°/90°] and an asymmetrical ply [0°/15°, 0°/30°,
0°/45°, 0°/60° 0°/75° and 0°/90°]. The bending flexure stress of the
CFRP specimen was evaluated through a bending test. Its thermal
property was measured using an infrared camera. The symmetrical
specimen and the asymmetrical specimen were analyzed. The results
showed that the asymmetrical specimen increased the bending loads
according to the increase in the orientation angle; and from 0°, the
symmetrical specimen showed a tendency opposite the asymmetrical
tendency because the tensile force of fiber differs at the vertical
direction of its load. Also, the infrared camera showed that the thermal
property had a trend similar to that of the mechanical properties.