Abstract: In general, it is desirable to finish the weld quickly,
before a large volume of surrounding metal heats up and expands.
The welding process used, type, welding current and speed of travel,
thus, affect the degree of shrinkage and distortion of a weldment. The
use of mechanized welding equipment reduces welding time, metal
affected zone and consequently distortion. This article helps to define
what weld distortion is and then provide a practical understanding of
the causes of distortion, effects of shrinkage in butt joint welded
assemblies using TI6AL4VA and Aluminium AA2024 alloy sheet.
The beam offset position to the joint interface towards titanium and
aluminium side. The factors affecting distortion during welding is
also given. Test results reveal that welding speed is the significant
parameter to decide the extent of distortion. Also welding from Al
side reduces the distortion while Ti side increases the distortion.
Abstract: This research paper portrays a comparative analysis of
thermomechanical behaviour of Shielded Metal Arc Welding
(SMAW) and Gas Tungsten Arc Welding (GTAW) of low carbon
steel of AISI 1020 grade butt joints. The thermal history has been
obtained by experimental work. We have focused on temperature
dependent cooling rate as depicted by Adam’s two-dimensional
model. The effect of moving point heat source of SMAW and GTAW
on mechanical properties has been judged by optical and scanning
electron micrographs of different regions in weld joints. The
microhardness study has been carried to visualize the joint strength
due to formation of different phases.
Abstract: In this research article a comprehensive investigation
has been carried out to determine the effect of thermal cycle on
temperature dependent process parameters developed during gas
tungsten arc (GTA) welding of high carbon (AISI 1090) steel butt
joints. An experiment based thermal analysis has been performed to
obtain the thermal history. We have focused on different
thermophysical properties such as thermal conductivity, heat transfer
coefficient and cooling rate. Angular torch model has been utilized to
find out the surface heat flux and its variation along the fusion zone as
well as along the longitudinal direction from fusion boundary. After
welding and formation of weld pool, heat transfer coefficient varies
rapidly in the vicinity of molten weld bead and heat affected zone. To
evaluate the heat transfer coefficient near the fusion line and near the
rear end of the plate (low temperature region), established correlation
has been implemented and has been compared with empirical
correlation which is noted as coupled convective and radiation heat
transfer coefficient. Change in thermal conductivity has been
visualized by analytical model of moving point heat source. Rate of
cooling has been estimated by using 2-dimensional mathematical
expression of cooling rate and it has shown good agreement with
experimental temperature cycle. Thermophysical properties have been
varied randomly within 0 -10s time span.
Abstract: This work presents the result of investigations aimed
at determining the hardness of the welded Chromoly (A 4130) steel
plate of 2” thickness. Multi pass welding for the thick sections was
carried out and analyzed for the Chromoly alloy steel plates. The
study of hardness at the weld metal reveals that there is the presence
of different micro structure products which yields diverse properties.
The welding carried out using GMAW with ER70s-2 electrode.
Single V groove design was selected for the butt joint configuration.
The presence of hydrogen has been suppressed by selecting low
hydrogen electrode. Preheating of the plate prior to welding reduces
the cooling rate which also affects the weld metal microstructure. The
shielding gas composition used in this analysis is 80% Ar-20% CO2.
The experimental analysis gives the detailed study of the hardness of
the material.
Abstract: Microplasma welding is a less expensive alternative to
laser welding in dental technology. The aim of the study was to
highlight discontinuities present in the microplasma welded joints of
dental base metal alloys by visual analysis. Five base metal alloys
designated for fixed prostheses manufacture were selected for the
experiments. Using these plates, preliminary tests were conducted by
microplasma welding in butt joint configuration, without filler
material, bilaterally and with filler material, proper for each base
metal. Macroscopic visual inspection was performed to assess
carefully the irregularities in the welds. Electron microscopy allowed
detection of discontinuities that are not visible to the eye and
revealing details regarding location, trajectory, morphology and size
of discontinuities. Supplementing visual control with microscopic
analysis allows to detect small discontinuities, which escapes the
macroscopic control and to make a detailed study of the weld.