Abstract: In this study, a three dimensional numerical heat
transfer model has been used to simulate the laser structuring of
polymer substrate material in the Three-Dimensional Molded
Interconnect Device (3D MID) which is used in the advanced multifunctional
applications. A finite element method (FEM) transient
thermal analysis is performed using APDL (ANSYS Parametric
Design Language) provided by ANSYS. In this model, the effect of
surface heat source was modeled with Gaussian distribution, also the
effect of the mixed boundary conditions which consist of convection
and radiation heat transfers have been considered in this analysis. The
model provides a full description of the temperature distribution, as
well as calculates the depth and the width of the groove upon material
removal at different set of laser parameters such as laser power and
laser speed. This study also includes the experimental procedure to
study the effect of laser parameters on the depth and width of the
removal groove metal as verification to the modeled results. Good
agreement between the experimental and the model results is
achieved for a wide range of laser powers. It is found that the quality
of the laser structure process is affected by the laser scan speed and
laser power. For a high laser structured quality, it is suggested to use
laser with high speed and moderate to high laser power.
Abstract: During welding, the amount of heat present in weld
zones determines the quality of weldment produced. Thus, the heat
distribution characteristics and its magnitude in weld zones with
respect to process variables such as tool pin-shoulder rotational and
traveling speed during welding is analyzed using thermal finite
element analyses method. For this purpose, transient thermal finite
element analyses are performed to model the temperatures
distribution and its quantities in weld-zones with respect to process
variables such as rotational speed and traveling speed during welding.
Commercially available software Altair HyperWork is used to model
three-dimensional tool pin-shoulder vs. workpieces and to simulate
the friction stir process. The results show that increasing tool
rotational speed, at a constant traveling speed, will increase the
amount of heat generated in weld-zones. In contrary, increasing
traveling speed, at constant tool pin-shoulder rotational speeds, will
reduce the amount of heat generated in weld zones.
Abstract: In this paper, strontium ferrite (SrO.6Fe2O3) was
synthesized by the sol-gel auto-combustion process. The thermal
behavior of powder obtained from self-propagating combustion of
initial gel was evaluated by simultaneous differential thermal analysis
(DTA) and thermo gravimetric (TG), from room temperature to
1200°C. The as-burnt powder was calcined at various temperatures
from 700-900°C to achieve the single-phase Sr-ferrite. Phase
composition, morphology and magnetic properties were investigated
using X-ray diffraction (XRD), transmission electron microscopy
(TEM) and vibrating sample magnetometry (VSM) techniques.
Results showed that the single-phase and nano-sized hexagonal
strontium ferrite particles were formed at calcination temperature of
800°C with crystallite size of 27 nm and coercivity of 6238 Oe.
Abstract: Boron-gypsum is a waste which occurs in the boric
acid production process. In this study, the boron content of this waste
is evaluated for the use in synthesis of magnesium borates and such
evaluation of this kind of waste is useful more than storage or
disposal. Magnesium borates, which are a sub-class of boron
minerals, are useful additive materials for the industries due to their
remarkable thermal and mechanical properties. Magnesium borates
were obtained hydrothermally at different temperatures. Novelty of
this study is the search of the solution density effects to magnesium
borate synthesis process for the increasing the possibility of borongypsum
usage as a raw material. After the synthesis process, products
are subjected to XRD and FT-IR to identify and characterize their
crystal structure, respectively.
Abstract: Fly ash is an important waste, produced in thermal
power plants which causes very important environmental pollutions.
For this reason the usage and evaluation the fly ash in various areas
are very important. Nearly, 15 million tons/year of fly ash is
produced in Turkey. In this study, usage of fly ash with diatomite and
molasses for heavy metal (Cd) adsorption from wastewater is
investigated. The samples of Seyitomer region fly ash were analyzed
by X-ray fluorescence (XRF) and Scanning Electron Microscope
(SEM) then diatomite (0 and 1% in terms of fly ash, w/w) and
molasses (0-0.75 mL) were pelletized under 30 MPa of pressure for
the usage of cadmium (Cd) adsorption in wastewater. After the
adsorption process, samples of Seyitomer were analyzed using
Optical Emission Spectroscopy (ICP-OES). As a result, it is seen that
the usage of Seyitomer fly ash is proper for cadmium (Cd) adsorption
and an optimum adsorption yield with 52% is found at a compound
with Seyitomer fly ash (10 g), diatomite (0.5 g) and molasses (0.75
mL) at 2.5 h of reaction time, pH:4, 20ºC of reaction temperature and
300 rpm of stirring rate.
Abstract: Three dimensional non-Interlaced carbon fibre
reinforced silicon carbide (3-D-Cf/SiC) composites with pyrocarbon
interphase were fabricated using isothermal chemical vapor
infiltration (ICVI) combined with polymer impregnation pyrolysis
(PIP) process. Polysilazane (PSZ) is used as a preceramic polymer to
obtain silicon carbide matrix. Thermo gravimetric analysis (TGA),
Infrared spectroscopic analysis (IR) and X-ray diffraction (XRD)
analysis were carried out on PSZ pyrolysed at different temperatures
to understand the pyrolysis and obtaining the optimum pyrolysing
condition to yield β-SiC phase. The density of the composites was
1.94 g cm-3 after the 3-D carbon preform was SiC infiltrated for 280 h
with one intermediate polysilazane pre-ceramic PIP process.
Mechanical properties of the composite materials were investigated
under tensile, flexural, shear and impact loading. The values of
tensile strength were 200 MPa at room temperature (RT) and 195
MPa at 500°C in air. The average RT flexural strength was 243 MPa.
The lower flexural strength of these composites is because of the
porosity. The fracture toughness obtained from single edge notched
beam (SENB) technique was 39 MPa.m1/2. The work of fracture
obtained from the load-displacement curve of SENB test was 22.8
kJ.m-2. The composites exhibited excellent impact resistance and the
dynamic fracture toughness of 44.8 kJ.m-2 is achieved as determined
from instrumented Charpy impact test. The shear strength of the
composite was 93 MPa, which is significantly higher compared 2-D
Cf/SiC composites. Microstructure evaluation of fracture surfaces
revealed the signatures of fracture processes and showed good
support for the higher toughness obtained.
Abstract: Concerns on corrosion and effective coating
protection of double hull tankers and bulk carriers in service have
been raised especially in water ballast tanks (WBTs). Test
protocols/methodologies specifically that which is incorporated in the
International Maritime Organisation (IMO), Performance Standard
for Protective Coatings for Dedicated Sea Water ballast tanks (PSPC)
are being used to assess and evaluate the performance of the coatings
for type approval prior to their application in WBTs. However, some
of the type approved coatings may be applied as very thick films to
less than ideally prepared steel substrates in the WBT. As such films
experience hygrothermal cycling from operating and environmental
conditions, they become embrittled which may ultimately result in
cracking. This embrittlement of the coatings is identified as an
undesirable feature in the PSPC but is not mentioned in the test
protocols within it. There is therefore renewed industrial research
aimed at understanding this issue in order to eliminate cracking and
achieve the intended coating lifespan of 15 years in good condition.
This paper will critically review test protocols currently used for
assessing and evaluating coating performance, particularly the IMO
PSPC.
Abstract: Thermal insulation materials based on natural fibers
represent a very promising area of materials based on natural easy
renewable row sources. These materials may be in terms of the
properties of most competing synthetic insulations, but show
somewhat higher moisture sensitivity and thermal insulation
properties are strongly influenced by the density and orientation of
fibers. The paper described the problem of hygrothermal behavior of
thermal insulation materials based on natural plant and animal fibers.
This is especially the dependence of the thermal properties of these
materials on the type of fiber, bulk density, temperature, moisture and
the fiber orientation.
Abstract: Because of high thermal efficiency and low CO2
emission, diesel engines are being used widely in many industrial
fields although it makes many PM and NOx which give both human
health and environment a negative effect. NOx regulations for diesel
engines, however, are being strengthened and it is impossible to meet
the emission standard without NOx reduction devices such as SCR
(Selective Catalytic Reduction), LNC (Lean NOx Catalyst), and LNT
(Lean NOx Trap). Among the NOx reduction devices, urea-SCR
system is known as the most stable and efficient method to solve the
problem of NOx emission. But this device has some issues associated
with the ammonia slip phenomenon which is occurred by shortage of
evaporation and thermolysis time, and that makes it difficult to achieve
uniform distribution of the injected urea in front of monolith.
Therefore, this study has focused on the mixing enhancement between
urea and exhaust gases to enhance the efficiency of the SCR catalyst
equipped in catalytic muffler by changing inlet gas temperature and
spray conditions to improve the spray uniformity of the urea water
solution. Finally, it can be found that various parameters such as inlet
gas temperature and injector and injection angles significantly affect
the evaporation and mixing of the urea water solution with exhaust
gases, and therefore, optimization of these parameters are required.
Abstract: Al-Si-Mg-Ni(-Cu) alloys are widely used in the automotive industry. They have the advantage of low weight associated with low coefficient of thermal expansion and excellent mechanical properties – mainly at high temperatures. The corrosion resistance of these alloys in coastal area, particularly sea water, however is not yet known. In this investigation, electrochemical impedance spectroscopy (EIS) and potentiodynamic polarization have been used to evaluate the corrosion resistance of Al-6Si-0.5Mg-2Ni (-2Cu) alloys in simulated sea water environments. The potentiodynamic polarization curves reveal that 2 wt% Cu content alloy (Alloy-2) is more prone to corrosion than the Cu free alloy (Alloy-1). But the EIS test results showed that corrosion resistance or charge transfer resistance (Rct) increases with the addition of Cu. Due to addition of Cu and thermal treatment, the magnitude of open circuit potential (OCP), corrosion potential (Ecorr) and pitting corrosion potential (Epit) of Al-6Si-0.5Mg-2Ni alloy in NaCl solution were shifted to the more noble direction.
Abstract: A phase diagram of the Ag2SO4 - CaSO4 (Silver sulphate – Calcium Sulphate) binaries system using conductivity, XRD (X-Ray Diffraction Technique) and DTA (Differential Thermal Analysis) data is constructed. The eutectic reaction (liquid -» a-Ag2SO4 + CaSO4) is observed at 10 mole% CaSO4 and 645°C. Room temperature solid solubility limit up to 5.27 mole % of Ca 2+ in Ag2SO4 is set using X-ray powder diffraction and scanning electron microscopy results. All compositions beyond this limit are two-phase mixtures below and above the transition temperature (≈ 416°C). The bulk conductivity, obtained following complex impedance spectroscopy, is found decreasing with increase in CaSO4 content. Amongst other binary compositions, the 80AgSO4-20CaSO4 gave improved sinterability/packing density.
Abstract: A new algorithm based on the lattice Boltzmann method (LBM) is proposed as a potential solver for one-dimensional heat and mass transfer for isothermal carbonization of wood particles. To check the validity of this algorithm, the LBM results have been compared with the published data and a good agreement is obtained. Then, the model is used to study the effect of reactor temperature and particle size on the evolution of the local temperature and mass loss inside the wood particle.
Abstract: In this paper, sodium borosilicates glasses were prepared by melting in air. These heat-resistant transparent glasses have subjected subsequently isothermal treatments at different times, which have transformed them at opaque glass (milky white color). Such changes indicate that these glasses showed clearly phase separation (immiscibility). The immiscibility region in a sodium borosilicate ternary system was investigated in this work, i.e. to determine the regions from which some compositions can show phase separation. For this we went through the conditions of thermodynamic equilibrium, which were translated later by mathematical equations to find an approximate solution. The latter has been translated in a simulation which was established thereafter to find the immiscibility regions in this type of special glasses.
Abstract: Heat transfer from flat tube is studied numerically. Reynolds number is defined base on equivalent circular tube which is varied in range of 100 to 300. In these range of Reynolds number flow is considered to be laminar, unsteady, and incompressible. Equations are solved by using finite volume method. Results show that increasing l/D from 1 to 2 has insignificant effect on heat transfer and Nusselt number of flat tube is slightly lower than circular tube. However, thermal-hydraulic performance of flat tube is up to 2.7 times greater than circular tube.
Abstract: Sustainable tall buildings that provide comfortable,
healthy and efficient indoor environments are clearly desirable as the
densification of living and working space for the world’s increasing
population proceeds. For environmental concerns, these buildings
must also be energy efficient. One component of these tasks is the
provision of indoor air quality and thermal comfort, which can be
enhanced with natural ventilation by the supply of fresh air. Working
spaces can only be naturally ventilated with connections to the
outdoors utilizing operable windows, double facades, ventilation
stacks, balconies, patios, terraces and skygardens. Large amounts of
fresh air can be provided to the indoor spaces without mechanical
air-conditioning systems, which are widely employed in
contemporary tall buildings.
This paper tends to present the concept of natural ventilation for
sustainable tall office buildings in order to achieve healthy and
comfortable working spaces, as well as energy efficient
environments. Initially the historical evolution of ventilation
strategies for tall buildings is presented, beginning with natural
ventilation and continuing with the introduction of mechanical airconditioning
systems. Then the emergence of natural ventilation due
to the health and environmental concerns in tall buildings is handled,
and the strategies for implementing this strategy are revealed. In the
next section, a number of case studies that utilize this strategy are
investigated. Finally, how tall office buildings can benefit from this
strategy is discussed.
Abstract: Photoacoustic imaging (PAI) is a non-invasive and
non-ionizing imaging modality that combines the absorption contrast
of light with ultrasound resolution. Laser is used to deposit optical
energy into a target (i.e., optical fluence). Consequently, the target
temperature rises, and then thermal expansion occurs that leads to
generating a PA signal. In general, most image reconstruction
algorithms for PAI assume uniform fluence within an imaging object.
However, it is known that optical fluence distribution within the
object is non-uniform. This could affect the reconstruction of PA
images. In this study, we have investigated the influence of optical
fluence distribution on PA back-propagation imaging using finite
element method. The uniform fluence was simulated as a triangular
waveform within the object of interest. The non-uniform fluence
distribution was estimated by solving light propagation within a
tissue model via Monte Carlo method. The results show that the PA
signal in the case of non-uniform fluence is wider than the uniform
case by 23%. The frequency spectrum of the PA signal due to the
non-uniform fluence has missed some high frequency components in
comparison to the uniform case. Consequently, the reconstructed
image with the non-uniform fluence exhibits a strong smoothing
effect.
Abstract: The process of thermoforming a carbon fiber reinforced thermoplastic (CFRTP) has increased its presence in the automotive industry for its wide applicability to the mass production car. A non-isothermal forming for CFRTP can shorten its cycle time to less than 1 minute. In this paper, the textile reinforcement FE model which the authors proposed in a previous work is extended to the CFRTP model for non-isothermal forming simulation. The effect of thermoplastic is given by adding shell elements which consider thermal effect to the textile reinforcement model. By applying Reuss model to the stress calculation of thermoplastic, the proposed model can accurately predict in-plane shear behavior, which is the key deformation mode during forming, in the range of the process temperature. Using the proposed model, thermoforming simulation was conducted and the results are in good agreement with the experimental results.
Abstract: Surplus electricity can be converted into potential energy via pumped hydroelectric storage for future usage. Similarly, thermo-electric energy storage (TEES) uses heat pumps equipped with thermal storage to convert electrical energy into thermal energy; the stored energy is then converted back into electrical energy when necessary using a heat engine. The greatest advantage of this method is that, unlike pumped hydroelectric storage and compressed air energy storage, TEES is not restricted by geographical constraints. In this study, performance variation of the TEES according to the changes in cold-side storage temperature was investigated by simulation method.
Abstract: This study presents the numerical simulation of three-dimensional incompressible steady and laminar fluid flow and conjugate heat transfer of a trapezoidal microchannel heat sink using water as a cooling fluid in a silicon substrate. Navier-Stokes equations with conjugate energy equation are discretized by finite-volume method. We perform numerical computations for a range of 50 ≦ Re ≦ 600, 0.05W ≦ P ≦ 0.8W, 20W/cm2 ≦q"≦ 40W/cm2. The present study demonstrates the numerical optimization of a trapezoidal microchannel heat sink design using the response surface methodology (RSM) and the genetic algorithm method (GA). The results show that the average Nusselt number increases with an increase in the Reynolds number or pumping power, and the thermal resistance decreases as the pumping power increases. The thermal resistance of a trapezoidal microchannel is minimized for a constant heat flux and constant pumping power.
Abstract: This paper investigates the natural convection heat transfer performance in a complex-wavy-wall cavity filled with power-law fluid. In performing the simulations, the continuity, Cauchy momentum and energy equations are solved subject to the Boussinesq approximation using a finite volume method. The simulations focus specifically on the effects of the flow behavior index in the power-law model and the Rayleigh number on the flow streamlines, isothermal contours and mean Nusselt number within the cavity. The results show that pseudoplastic fluids have a better heat transfer performance than Newtonian or dilatant fluids. Moreover, it is shown that for Rayleigh numbers greater than Ra=103, the mean Nusselt number has a significantly increase as the flow behavior index is decreased.