Abstract: Wet scrubbers have found widespread use in cleaning
contaminated gas streams because of their ability to remove
particulates and based on the applications of scrubbing of marine
engine exhaust gases by spraying sea-water. In order to examine the
flow characteristics inside the scrubber, the model is designated with
flow properties of hot air and water sprayer. The flow dynamics of
evaporation of hot air by the injection of water droplets is the key
factor considered in this paper. The flow behavior inside the scrubber
was investigated from the previous works and to sum up the
evaporation rate with respect to the concentration of water droplets are
predicted to bring out the competent modelling. The numerical
analysis using CFD facilitates in understanding the problem better and
empathies the behavior of the model over its entire operating envelope.
Abstract: In this numerical study, we want to present the design
of highly efficient extruded-type heat sink. The symmetrically
arranged extruded-type heat sinks are used instead of a single extruded
or swaged-type heat sink. In this parametric study, the maximum
temperatures, the base temperatures between heaters, and the heat
release rates were investigated with respect to the arrangements of heat
sources, air flow rates, and amounts of heat input. Based on the results
we believe that the use of both side of heat sink is to be much better for
release the heat than the use of single side. Also from the results, it is
believed that the symmetric arrangement of heat sources is
recommended to achieve a higher heat transfer from the heat sink.
Abstract: Because of high thermal efficiency and low CO2
emission, diesel engines are being used widely in many industrial
fields although it makes many PM and NOx which give both human
health and environment a negative effect. NOx regulations for diesel
engines, however, are being strengthened and it is impossible to meet
the emission standard without NOx reduction devices such as SCR
(Selective Catalytic Reduction), LNC (Lean NOx Catalyst), and LNT
(Lean NOx Trap). Among the NOx reduction devices, urea-SCR
system is known as the most stable and efficient method to solve the
problem of NOx emission. But this device has some issues associated
with the ammonia slip phenomenon which is occurred by shortage of
evaporation and thermolysis time, and that makes it difficult to achieve
uniform distribution of the injected urea in front of monolith.
Therefore, this study has focused on the mixing enhancement between
urea and exhaust gases to enhance the efficiency of the SCR catalyst
equipped in catalytic muffler by changing inlet gas temperature and
spray conditions to improve the spray uniformity of the urea water
solution. Finally, it can be found that various parameters such as inlet
gas temperature and injector and injection angles significantly affect
the evaporation and mixing of the urea water solution with exhaust
gases, and therefore, optimization of these parameters are required.
Abstract: Combustion phenomenon will be accomplished
effectively by the development of low emission combustor. One of the
significant factors influencing the entire Combustion process is the
mixing between a swirling angular jet (Primary Air) and the
non-swirling inner jet (fuel). To study this fundamental flow, the
chamber had to be designed in such a manner that the combustion
process to sustain itself in a continuous manner and the temperature of
the products is sufficiently below the maximum working temperature
in the turbine. This study is used to develop the effective combustion
with low unburned combustion products by adopting the concept of
high swirl flow and motility of holes in the secondary chamber. The
proper selection of a swirler is needed to reduce emission which can be
concluded from the emission of Nox and CO2. The capture of CO2 is
necessary to mitigate CO2 emissions from natural gas. Thus the
suppression of unburned gases is a meaningful objective for the
development of high performance combustor without affecting turbine
blade temperature.
Abstract: Emission regulations for diesel engines are being strengthened and it is impossible to meet the standards without exhaust after-treatment systems. Lack of the space in many diesel vehicles, however, make it difficult to design and install stand-alone catalytic converters such as DOC, DPF, and SCR in the vehicle exhaust systems. Accordingly, those have been installed inside the muffler to save the space, and referred to the catalytic muffler. However, that has complex internal structure with perforated plate and pipe for noise and monolithic catalyst for emission reduction. For this reason, flow uniformity and pressure drop, which affect efficiency of catalyst and engine performance, respectively, should be examined when the catalytic muffler is designed. In this work, therefore, the flow uniformity and pressure drop to improve the performance of the catalytic converter and the engine have been numerically investigated by changing various design parameters such as inlet shape, porosity, and outlet shape of the muffler using the three-dimensional turbulent flow of the incompressible, non-reacting, and steady state inside the catalytic muffler. Finally, it can be found that the shape, in which the muffler has perforated pipe inside the inlet part, has higher uniformity index and lower pressure drop than others considered in this work.
Abstract: A mathematical heat transfer model for the prediction of transient heating of the slab in a direct-fired walking beam type reheating furnace has been developed by considering the nongray thermal radiation with given furnace environments. The furnace is modeled as radiating nongray medium with carbon dioxide and water with five-zoned gas temperature and the furnace wall is considered as a constant temperature lower than furnace gas one. The slabs are moving with constant velocity depending on the residence time through the non-firing, charging, preheating, heating, and final soaking zones. Radiative heat flux obtained by considering the radiative heat exchange inside the furnace as well as convective one from the surrounding hot gases are introduced as boundary condition of the transient heat conduction within the slab. After validating thermal radiation model adopted in this work, thermal fields in both model and real reheating furnace are investigated in terms of radiative heat flux in the furnace and temperature inside the slab. The results show that the slab in the furnace can be more heated with higher slab emissivity and residence time.
Abstract: Catalytic combustion is generally accepted as an environmentally preferred alternative for the generation of heat and power from fossil fuels mainly due to its advantages related to the stable combustion under very lean conditions with low emissions of NOx, CO, and UHC at temperatures lower than those occurred in conventional flame combustion. Despite these advantages, the commercial application of catalytic combustion has been delayed because of complicated reaction processes and the difficulty in developing appropriate catalysts with the required stability and durability. To develop the catalytic combustors, detailed studies on the combustion characteristics of catalytic combustion should be conducted. To the end, in current research, quantitative studies on the combustion characteristics of the catalytic combustors, with a Pd-based catalyst for MCFC power generation systems, relying on numerical simulations have been conducted. In addition, data from experimental studies of variations in outlet temperatures and fuel conversion, taken after operating conditions have been used to validate the present numerical approach. After introducing the governing equations for mass, momentum, and energy equations as well as a description of catalytic combustion kinetics, the effects of the excess air ratio, space velocity, and inlet gas temperature on the catalytic combustion characteristics are extensively investigated. Quantitative comparisons are also conducted with previous experimental data. Finally, some concluding remarks are presented.
Abstract: Worldwide interests for the renewable energy are increasing due to environmental and climate changes from traditional petroleum related energy sources. To account for these social needs, ligneous biomass energy is considered as one of the environmentally friend energy solutions. The wood torrefaction process is a feasible method to improve the properties of the biomass fuel and makes the wood have low moisture, lower smoke emission and increased heating value. In this work, therefore, the moisture evaporation model which largely affects energy efficiency of ligneous biomass through moisture contents and heating value relative to its weight is studied with numerical modeling approach by analyzing the effects of torrefaction furnace temperature. The results show that the temperature and moisture fraction of wood decrease by increasing the furnace temperature. When the torrefaction temperature is lower than 423K, there were little changes of the moisture fraction in the wood. Also, it can be found that charcoal is produced more slowly when the torrefaction temperature is lower than 573K.
Abstract: In this work, the effects of scale on thermal behavior of the slab in a walking-beam type reheating furnace is studied by considering scale formation and growth in a furnace environment. Also, mathematical heat transfer model to predict the thermal radiation in a complex shaped reheating furnace with slab and skid buttons is developed with combined nongray WSGGM and blocked-off solution procedure. The model can attack the heat flux distribution within the furnace and the temperature distribution in the slab throughout the reheating furnace process by considering the heat exchange between the slab and its surroundings, including the radiant heat transfer among the slabs, the skids, the hot combustion gases and the furnace wall as well as the gas convective heat transfer in the furnace. With the introduction of the mathematical formulations validation of the present numerical model is conducted by calculating two example problems of blocked-off and nongray gas radiative heat transfer. After discussing the formation and growth of the scale on the slab surface, slab heating characteristics with scale is investigated in terms of temperature rise with time.
Abstract: In order to enhance the aircraft survivability, the
infrared signatures emitted by hot engine parts should be determined
exactly. For its reduction it is necessary for the rear fuselage
temperature to be decreased. In this study, numerical modeling of flow
fields and heat transfer characteristics of an aircraft nozzle is
performed and its temperature distribution along each component wall
is predicted. The radiation shield is expected to reduce the skin
temperature of rear fuselage. The effect of material characteristic of
radiation shield on the heat transfer is also investigated. Through this
numerical analysis, design parameters related to the susceptibility of
aircraft are examined.
Abstract: The objective of this work is to investigate the
turbulent reacting flow in a three dimensional combustor with
emphasis on the effect of inlet swirl flow through a numerical
simulation. Flow field is analyzed using the SIMPLE method which is
known as stable as well as accurate in the combustion modeling, and
the finite volume method is adopted in solving the radiative transfer
equation. In this work, the thermal and flow characteristics in a three
dimensional combustor by changing parameters such as equivalence
ratio and inlet swirl angle have investigated. As the equivalence ratio
increases, which means that more fuel is supplied due to a larger inlet
fuel velocity, the flame temperature increases and the location of
maximum temperature has moved towards downstream. In the mean
while, the existence of inlet swirl velocity makes the fuel and
combustion air more completely mixed and burnt in short distance.
Therefore, the locations of the maximum reaction rate and temperature
were shifted to forward direction compared with the case of no swirl.