Abstract: The use of synthetic retardants in polymeric insulated
cables is not uncommon in the high voltage engineering to study
electrical treeing phenomenon. However few studies on organic
materials for the same investigation have been carried. .This paper
describes the study on the effects of Oil Palm Empty Fruit Bunch
(OPEFB) microfiller on the tree initiation and propagation in silicone
rubber with different weight percentages (wt %) of filler to insulation
bulk material. The weight percentages used were 0 wt % and 1 wt %
respectively. It was found that the OPEFB retards the propagation of
the electrical treeing development. For tree inception study, the
addition of 1(wt %) OPEFB has increase the tree inception voltage of
silicone rubber. So, OPEFB is a potential retardant to the initiation
and growth of electrical treeing occurring in polymeric materials for
high voltage application. However more studies on the effects of
physical and electrical properties of OPEFB as a tree retardant
material are required.
Abstract: Bio-electrical responses obtained from freshwater
sediments by employing microbial fuel cell (MFC) technology were
investigated in this experimental study. During the electricity
generation, organic matter in the sediment was microbially oxidized
under anaerobic conditions with an electrode serving as a terminal
electron acceptor. It was found that the sediment organic matter
(SOM) associated with electrochemically-active electrodes became
more humified, aromatic, and polydispersed, and had a higher average
molecular weight, together with the decrease in the quantity of SOM.
The alteration of characteristics of the SOM was analogous to that
commonly observed in the early stage of SOM diagenetic process (i.e.,
humification). These findings including an elevation of the sediment
redox potential present a possibility of the MFC technology as a new
soil/sediment remediation technique based on its potential benefits:
non-destructive electricity generation and bioremediation.
Abstract: This work presents a comparison between the Annual
Energy Output (AEO) of two commercial vertical-axis wind turbines
(VAWTs) for a low-wind urban site: both a drag-driven and a liftdriven
concepts are examined in order to be installed on top of the
new Via dei Giustinelli building, Trieste (Italy). The power-curves,
taken from the product specification sheets, have been matched to the
wind characteristics of the selected installation site. The influence of
rotor swept area and rated power on the performance of the two
proposed wind turbines have been examined in detail, achieving a
correlation between rotor swept area, electrical generator size and
wind distribution, to be used as a guideline for the calculation of the
AEO.
Abstract: Internal combustion engines rejects 30-40% of the
energy supplied by fuel to the environment through exhaust gas. thus, there is a possibility for further significant improvement of efficiency with the utilization of exhaust gas energy and its conversion to mechanical energy or electrical energy. The Thermo-Electric
Generator (TEG) will be located in the exhaust system and will make use of an energy flow between the warmer exhaust gas and the external environment. Predict to th optimum position of temperature
distribution and the performance of TEG through numerical analysis.
The experimental results obtained show that the power output significantly increases with the temperature difference between cold
and hot sides of a thermoelectric generator.
Abstract: This paper describes the application of a model
predictive controller to the problem of batch reactor temperature
control. Although a great deal of work has been done to improve
reactor throughput using batch sequence control, the control of the
actual reactor temperature remains a difficult problem for many
operators of these processes. Temperature control is important as
many chemical reactions are sensitive to temperature for formation of
desired products. This controller consist of two part (1) a nonlinear
control method GLC (Global Linearizing Control) to create a linear
model of system and (2) a Model predictive controller used to obtain
optimal input control sequence. The temperature of reactor is tuned
to track a predetermined temperature trajectory that applied to the
batch reactor. To do so two input signals, electrical powers and the
flow of coolant in the coil are used. Simulation results show that the
proposed controller has a remarkable performance for tracking
reference trajectory while at the same time it is robust against noise
imposed to system output.
Abstract: Control of commutation of switched reluctance (SR)
motor has been an area of interest for researchers for sometime now
with mixed successes in addressing the inherent challenges. New
technologies, processing schemes and methods have been adopted to
make sensorless SR drive a reality. There are a number of
conceptual, offline, analytical and online solutions in literature that
have varying complexities and achieved equally varying degree of
robustness and accuracies depending on the method used to address
the challenges and the SR drive application. Magnetic coupling is
one such challenge when using active probing techniques to
determine rotor position of a SR motor from stator winding. This
paper studies the effect of back-of-core saturation on the detected
rotor position and presents results on measurement made on a 4-
phase SR motor. The results shows that even for a four phase motor
which is excited one phase at a time and using the electrically
opposite phase for active position probing, the back-of-core
saturation effects should not be ignored.
Abstract: When a high DC voltage is applied to a capacitor with
strongly asymmetrical electrodes, it generates a mechanical force that
affects the whole capacitor. This phenomenon is most likely to be
caused by the motion of ions generated around the smaller of the two
electrodes and their subsequent interaction with the surrounding
medium. A method to measure this force has been devised and used.
A formula describing the force has also been derived. After
comparing the data gained through experiments with those acquired
using the theoretical formula, a difference was found above a certain
value of current. This paper also gives reasons for this difference.
Abstract: This paper describes an efficient and practical method
for economic dispatch problem in one and two area electrical power
systems with considering the constraint of the tie transmission line
capacity constraint. Direct search method (DSM) is used with some
equality and inequality constraints of the production units with any
kind of fuel cost function. By this method, it is possible to use several
inequality constraints without having difficulty for complex cost
functions or in the case of unavailability of the cost function
derivative. To minimize the number of total iterations in searching,
process multi-level convergence is incorporated in the DSM.
Enhanced direct search method (EDSM) for two area power system
will be investigated. The initial calculation step size that causes less
iterations and then less calculation time is presented. Effect of the
transmission tie line capacity, between areas, on economic dispatch
problem and on total generation cost will be studied; line
compensation and active power with reactive power dispatch are
proposed to overcome the high generation costs for this multi-area
system.
Abstract: Metal matrix composites (MMC) are generating
extensive interest in diverse fields like defense, aerospace, electronics
and automotive industries. In this present investigation, material
removal rate (MRR) modeling has been carried out using an
axisymmetric model of Al-SiC composite during electrical discharge
machining (EDM). A FEA model of single spark EDM was
developed to calculate the temperature distribution.Further, single
spark model was extended to simulate the second discharge. For
multi-discharge machining material removal was calculated by
calculating the number of pulses. Validation of model has been done
by comparing the experimental results obtained under the same
process parameters with the analytical results. A good agreement was
found between the experimental results and the theoretical value.
Abstract: This paper describes the smart energy monitoring system with a wireless sensor network for monitoring of electrical usage in smart house. Proposed system is composed of wireless plugs and energy control wallpad server. The wireless plug integrates an AC power socket, a relay to switch the socket ON/OFF, a Hall effect sensor to sense current of load appliance and a Kmote. The Kmote is a wireless communication interface based on TinyOS. We evaluated wireless plug in a laboratory, analyzed and presented energy consumption data from electrical appliances for 3 months in home.
Abstract: Switched-mode converters play now a significant role in
modern society. Their operation are often crucial in various electrical
applications affecting the every day life. Therefore, the quality of
the converters needs to be reliably verified. Recent studies have
shown that the converters can be fully characterized by a set of
frequency responses which can be efficiently used to validate the
proper operation of the converters. Consequently, several methods
have been proposed to measure the frequency responses fast and
accurately. Most often correlation-based techniques have been applied.
The presented measurement methods are highly sensitive to
external errors and system nonlinearities. This fact has been often
forgotten and the necessary uncertainty analysis of the measured
responses has been neglected. This paper presents a simple approach
to analyze the noise and nonlinearities in the frequency-response
measurements of switched-mode converters. Coherence analysis is
applied to form a confidence interval characterizing the noise and
nonlinearities involved in the measurements. The presented method is
verified by practical measurements from a high-frequency switchedmode
converter.
Abstract: This paper presents a vertical silicon nanowire n- MOSFET integrated with a CMOS-compatible fully-silicided (FUSI) NiSi2 gate. Devices with nanowire diameter of 50nm show good electrical performance (SS < 70mV/dec, DIBL < 30mV/V, Ion/Ioff > 107). Most significantly, threshold voltage tunability of about 0.2V is shown. Although threshold voltage remains low for the 50nm diameter device, it is expected to become more positive as nanowire diameter reduces.
Abstract: The equations governing the flow of an electrically conducting, incompressible viscous fluid over an infinite flat plate in the presence of a magnetic field are investigated using the homotopy perturbation method (HPM) with Padé approximants (PA) and 4th order Runge–Kutta method (4RKM). Approximate analytical and numerical solutions for the velocity field and heat transfer are obtained and compared with each other, showing excellent agreement. The effects of the magnetic parameter and Prandtl number on velocity field, shear stress, temperature and heat transfer are discussed as well.
Abstract: This study fabricates p-type Ni1−xO:Li/n-Si heterojunction solar cells (P+/n HJSCs) by using radio frequency (RF) magnetron sputtering and investigates the effect of substrate temperature on photovoltaic cell properties. Grazing incidence x-ray diffraction, four point probe, and ultraviolet-visible-near infrared discover the optoelectrical properties of p-Ni1-xO thin films. The results show that p-Ni1-xO thin films deposited at 300 oC has the highest grain size (22.4 nm), average visible transmittance (~42%), and electrical resistivity (2.7 Ωcm). However, the conversion efficiency of cell is shown only 2.33% which is lower than the cell (3.39%) fabricated at room temperature. This result can be mainly attributed to interfacial layer thickness (SiOx) reduces from 2.35 nm to 1.70 nm, as verified by high-resolution transmission electron microscopy.
Abstract: With the prevalence of computer and development of information technology, Geographic Information Systems (GIS) have long used for a variety of applications in electrical engineering. GIS are designed to support the analysis, management, manipulation and mapping of spatial data. This paper presents several usages of GIS in power utilities such as automated route selection for the construction of new power lines which uses a dynamic programming model for route optimization, load forecasting and optimizing planning of substation-s location and capacity with comprehensive algorithm which involves an accurate small-area electric load forecasting procedure and simulates the different cost functions of substations.
Abstract: Wind is among the potential energy resources which
can be harnessed to generate wind energy for conversion into
electrical power. Due to the variability of wind speed with time and
height, it becomes difficult to predict the generated wind energy more
optimally. In this paper, an attempt is made to establish a
probabilistic model fitting the wind speed data recorded at
Makambako site in Tanzania. Wind speeds and direction were
respectively measured using anemometer (type AN1) and wind Vane
(type WD1) both supplied by Delta-T-Devices at a measurement
height of 2 m. Wind speeds were then extrapolated for the height of
10 m using power law equation with an exponent of 0.47. Data were
analysed using MINITAB statistical software to show the variability
of wind speeds with time and height, and to determine the underlying
probability model of the extrapolated wind speed data. The results
show that wind speeds at Makambako site vary cyclically over time;
and they conform to the Weibull probability distribution. From these
results, Weibull probability density function can be used to predict
the wind energy.
Abstract: The passive electrical properties of a tissue depends
on the intrinsic constituents and its structure, therefore by measuring
the complex electrical impedance of the tissue it might be possible to
obtain indicators of the tissue state or physiological activity [1].
Complete bio-impedance information relative to physiology and
pathology of a human body and functional states of the body tissue or
organs can be extracted by using a technique containing a fourelectrode
measurement setup. This work presents the estimation
measurement setup based on the four-electrode technique. First, the
complex impedance is estimated by three different estimation
techniques: Fourier, Sine Correlation and Digital De-convolution and
then estimation errors for the magnitude, phase, reactance and
resistance are calculated and analyzed for different levels of
disturbances in the observations. The absolute values of relative
errors are plotted and the graphical performance of each technique is
compared.
Abstract: the paper presents the optimization results for several
electrical machines dedicated for powered electric wheel-chairs. The
optimization, using the Hook-Jeeves algorithm, was employed based
on a design approach which takes into consideration the road
conditions. Also, through numerical simulations (based on finite
element method), the analytical approach was validated. The
optimization approach gave satisfactory results and the best suited
variant was chosen for the motorization of the wheel-chair.
Abstract: The electrical interaction between two axisymmetric
spheroidal particles in an electrolyte solution is examined numerically.
A Galerkin finite element method combined with a Newton-Raphson
iteration scheme is proposed to evaluate the spatial variation in the
electrical potential, and the result obtained used to estimate the
interaction energy between two particles. We show that if the surface
charge density is fixed, the potential gradient is larger at a point, which
has a larger curvature, and if surface potential is fixed, surface charge
density is proportional to the curvature. Also, if the total interaction
energy against closest surface-to-surface curve exhibits a primary
maximum, the maximum follows the order (oblate-oblate) >
(sphere-sphere)>(oblate-prolate)>(prolate-prolate), and if the curve
has a secondary minimum, the absolute value of the minimum follows
the same order.
Abstract: An electrical apparatus for measuring moisture
content was developed by our laboratory and uses dependence of
electrical properties on water content in studied material. Error
analysis of the apparatus was run by measuring different volumes of
water in a simplified specimen, i.e. hollow plexiglass block, in order
to avoid as many side-effects as possible. Obtained data were
processed using both basic and advanced statistics and results were
compared with each other. The influence of water content on
accuracy of measured data was studied as well as the influence of
variation of apparatus' proper arrangement or factual methodics of its
usage. The overall coefficient of variation was 4%. There was no
trend found in results of error dependence on water content.
Comparison with current surveys led to a conclusion, that the studied
apparatus can be used for indirect measurement of water content in
porous materials, with expectable error and under known conditions.
Factual experiments with porous materials are not involved, but are
currently under investigation.