Abstract: Power quality is used to describe the degree of consistency of electrical energy expected from generation source to point of use. The term power quality refers to a wide variety of electromagnetic phenomena that characterize the voltage and current at a given time and at a given location on the power system. Power quality problems can be defined as problem that results in failure of customer equipments, which manifests itself as an economic burden to users, or produces negative impacts on the environment. Voltage stability, power factor, harmonics pollution, reactive power and load unbalance are some of the factors that affect the consistency or the quality level. This research proposal proposes to investigate and analyze the causes and effects of power quality to homes and industries in Sarawak. The increasing application of electronics equipment used in the industries and homes has caused a big impact on the power quality. Many electrical devices are now interconnected to the power network and it can be observed that if the power quality of the network is good, then any loads connected to it will run smoothly and efficiently. On the other hand, if the power quality of the network is bad, then loads connected to it will fail or may cause damage to the equipments and reduced its lifetime. The outcome of this research will enable better and novel solutions of poor power quality to small industries and reduce damage of electrical devices and products in the industries.
Abstract: Psychoacoustics has become a potential area of research due to the growing interest of both laypersons and medical and mental health professionals. Non invasive brain computer interface like Electroencephalography (EEG) is widely being used in this field. An attempt has been made in this paper to examine the response of EEG signals to acoustic stimuli further analyzing the brain electrical activity. The real time EEG is acquired for 6 participants using a cost effective and portable EMOTIV EEG neuro headset. EEG data analysis is further done using EMOTIV test bench, EDF browser and EEGLAB (MATLAB Tool) application software platforms. Spectral analysis of acquired neural signals (AF3 channel) using these software platforms are clearly indicative of increased brain activity in various bands. The inferences drawn from such an analysis have significant correlation with subject’s subjective reporting of the experiences. The results suggest that the methodology adopted can further be used to assist patients with sleeping and depressive disorders.
Abstract: The effect of nonthermal pulsed electric field (PEF) and thermal treatment (90⁰C for 60s) was studied on quality parameters of emblica officinalis juice for the period of 6 weeks at 4⁰C using monopolar rectangular pulse of 1µs width. The PEF treatment was given using static chamber at 24kV/cm for 500µs. The quality of emblica officinalis juice was investigated in terms of non enzymatic browning index (NEBI), 5-hydroxymethyl-2-furfural (HMF), total polyphenol content and antioxidant capacity. ⁰Brix, pH and conductivity were evaluated as physical parameters. The aim of the work was to investigate the effect of PEF on the retention of bioactive compounds and retardation of browning activity. The results showed that conventional thermal treatment had led to a significant (p < 0.05) decrease of 48.15% in polyphenol content (129.56 mg of GAE L-1), with higher NEBI and HMF formation (p < 0.05) whilst PEF suppressed NEBI and retained higher polyphenol compounds (168.59 mg GAE L-1) with limiting the loss to 32.56% along maximum free radical scavenging activity (92.07%). However, pH, ⁰brix and electrical conductivity of treated juice samples remain unaffected. Therefore, PEF can be considered as an effective nonthermal treatment for retaining bioactive compounds along suppressing browning of emblica juice.
Abstract: Resistive Random Access Memory (RRAM) had received great amount of attention from various research efforts in recent years, owing to its promising performance as a next generation memory device. In this paper, samples based on TiN/HfOx/Pt stack were prepared and its electrical switching behaviors were characterized and discussed in brief.
Abstract: Development of microprocessor controlled sensor for measurement of wind speed and direction is the aim of this study. Electrical circuits and software were developed to the existing electromechanical part of the sensor TM-W2 becoming the properties of so-called smart sensor. The measured data about wind speed (sensitivity 0.01 m/s) and direction (0-360° by step 10°) are transmitted as 16-bit information. The connection between sensor and control unit is realized by radio communication (FM 433 MHz). Transition range is 220 m if used Quad type antenna. This concept provides substitution of actual cable systems by wireless ones.
Abstract: In this paper, we present a comparative study of the
genetic algorithms and Hessian-s methods for optimal research of the
active powers in an electric network of power. The objective function
which is the performance index of production of electrical energy is
minimized by satisfying the constraints of the equality type and
inequality type initially by the Hessian-s methods and in the second
time by the genetic Algorithms. The results found by the application
of AG for the minimization of the electric production costs of power
are very encouraging. The algorithms seem to be an effective
technique to solve a great number of problems and which are in
constant evolution. Nevertheless it should be specified that the
traditional binary representation used for the genetic algorithms
creates problems of optimization of management of the large-sized
networks with high numerical precision.
Abstract: The electrical power systems of aircrafts have made
serious progress in recent years because the aircrafts depend more
and more on the electricity. There is a trend in the aircraft industry to
replace hydraulic and pneumatic systems with electrical systems,
achieving more comfort and monitoring features and enlarging the
energetic efficiency. Thus, was born the concept More Electric
Aircraft. In this paper is analyzed the integration of a fuel cell into
the existing electrical generation and distribution systems of an
aircraft. The dynamic characteristics of fuel cell systems necessitate
an adaptation of the electrical power system. The architecture studied
in this paper consists of a 50kW fuel cell, a dc to dc converter and
several loads. The dc to dc converter is used to step down the fuel
cell voltage from about 625Vdc to 28Vdc.
Abstract: MOSCAPs of various combinations of Hafnium
oxide and Titanium oxide of varying thickness with Aluminum as gate electrode have been fabricated and electrically characterized.
The effects of voltage stress on the I-V characteristics for prolonged time durations have been studied and compared. Results showed
hard breakdown and negligible degradation of reliability under stress.
Abstract: Hydrogen diffusion is the main problem for corrosion fatigue in corrosive environment. In order to analyze the phenomenon, it is needed to understand their behaviors specially the hydrogen behavior during the diffusion. So, Hydrogen embrittlement and prediction its behavior as a main corrosive part of the fractions, needed to solve combinations of different equations mathematically. The main point to obtain the equation, having knowledge about the source of causing diffusion and running the atoms into materials, called driving force. This is produced by either gradient of electrical or chemical potential. In this work, we consider the gradient of chemical potential to obtain the property equation. In diffusion of atoms, some of them may be trapped but, it could be ignorable in some conditions. According to the phenomenon of hydrogen embrittlement, the thermodynamic and chemical properties of hydrogen are considered to justify and relate them to fracture mechanics. It is very important to get a stress intensity factor by using fugacity as a property of hydrogen or other gases. Although, the diffusive behavior and embrittlement event are common and the same for other gases but, for making it more clear, we describe it for hydrogen. This considering on the definite gas and describing it helps us to understand better the importance of this relation.
Abstract: The current-voltage characteristics of a PtSi/p-Si
Schottky barrier diode was measured at the temperature of 85 K and
from the forward bias region of the I-V curve, the electrical
parameters of the diode were measured by three methods. The results
obtained from the two methods which considered the series resistance
were in close agreement with each other and from them barrier height
(), ideality factor (n) and series resistance () were found to be
0.2045 eV, 2.877 and 14.556 K respectively. By measuring the I-V
characteristics in the temperature range of 85-136 K the electrical
parameters were observed to have strong dependency on temperature.
The increase of barrier height and decrease of ideality factor with
increasing temperature is attributed to the existence of barrier height
inhomogeneities in the silicide-semiconductor structure.
Abstract: Overhead electrical insulators form an important link in an electric power system. Along with the traditional insulators (i.e. glass and porcelain, etc) presently the polymeric insulators are also used world widely. These polymeric insulators are very sensitive to various environmental parameters such temperature, environmental pollution, UV-radiations, etc. which seriously effect their electrical, chemical and hydrophobic properties. The UV radiation level in the central region of Saudi Arabia is high as compared to the IEC standard for the accelerated aging of the composite insulators. Commonly used suspension type of composite EPDM (Ethylene Propylene Diene Monomer) insulator was subjected to accelerated stress aging as per modified IEC standard simulating the inland arid deserts atmospheric condition and also as per IEC-61109 standard. The hydrophobic characteristics were studied by measuring the contact angle along the insulator surface before and after the accelerated aging of the samples. It was found that EPDM insulator loses it hydrophobic properties proportional to the intensity of UV irradiations and its rate of recovery is also very low as compared to Silicone Rubber insulator.KeywordsEPDM, composite insulators, accelerated aging, hydrophobicity, contact angle.
Abstract: This paper presents the experimental results on space charge distribution in cross-linked polyethylene (XLPE) insulating material for 22 kV power distribution system cable by using pulse electroacoustic measurement technique (PEA). Numbers of XLPE insulating material ribbon having thickness 60 μm taken from unused 22 kV high voltage cable were used as specimen in this study. DC electric field stress was applied to test specimen at room temperature (25°C). Four levels of electric field stress, 25 kV/mm, 50 kV/mm, 75 kV/mm and 100 kV/mm, were used. In order to investigate space charge distribution characteristic, space charge distribution characteristics were measured after applying electric field stress 15 min, 30 min and 60 min, respectively. The results show that applied time and magnitude of dc electric field stress play an important role to the formation of space charge.
Abstract: Any use of energy in industrial productive activities is combined with various environment impacts. Withintransportation,
this fact was not only found among land transport, railways and maritime transport, but also in the air transport industry. An effective climate protection requires strategies and measures for reducing all
greenhouses gas emissions, in particular carbon dioxide, and must
take into account the economic, ecologic and social aspects. It seem simperative now to develop and manufacture environmentally
friendly products and systems, to reduce consumption and use less
resource, and to save energy and power. Today-sproducts could
better serve these requirements taking into account the integration of
a power management system into the electrical power system.This
paper gives an overview of an approach ofpower management with
load prioritization in modernaircraft. Load dimensioning and load
management strategies on current civil aircraft will be presented and
used as a basis for the proposed approach.
Abstract: A vertical SOI-based MOSFET with trench body
structure operated as 1T DRAM cell at various temperatures has been
studied and investigated. Different operation temperatures are
assigned for the device for its performance comparison, thus the
thermal stability is carefully evaluated for the future memory device
applications. Based on the simulation, the vertical SOI-based
MOSFET with trench body structure demonstrates the electrical
characteristics properly and possess conspicuous kink effect at
various operation temperatures. Transient characteristics were also
performed to prove that its programming window values and
retention time behaviors are acceptable when the new 1T DRAM cell
is operated at high operation temperature.
Abstract: The protection of groundwater resources is the great
important many semiarid and arid environments. Baghan watershed
is located in the north of Kangan in the Boshehr province in Iran. The
groundwater resources have a vital role in supplying agricultural,
drinking, domestic and industrial water demand in Baghan
watershed. For our investigation into the water quality we collected
30 samples to chemical and physical analysis. The result showed the
marl and evaporation deposits that contain anhydrite and gypsum is
the main source of groundwater pollution, and one part of the
groundwater was polluted by oil and gas industrial. Another part of
the groundwater was contaminated by urban waste water. The
electrical conductivity and captions and anions increased around of
towns and gas refinery. Although the negative impact of untreated
domestic wastewater is relatively low but the results showed strongly
the negative impact of wastewater refinery is very considerable. This
negative impact increased in downstream due to shallow aquifer.
Additionally, the agents that adversely affect the quality of
groundwater come from a variety of sources, including geology,
domestic wastewater and the Jam refinery in Baghan watershed.
Abstract: Retinal prostheses have been successful in eliciting
visual responses in implanted subjects. As these prostheses progress,
one of their major limitations is the need for increased resolution. As
an alternative to increasing the number of electrodes, virtual
electrodes may be used to increase the effective resolution of current
electrode arrays. This paper presents a virtual electrode technique
based upon time-offsets between stimuli. Two adjacent electrodes are
stimulated with identical pulses with too short of pulse widths to
activate a neuron, but one has a time offset of one pulse width. A
virtual electrode of twice the pulse width was then shown to appear in
the center, with a total width capable of activating a neuron. This can
be used in retinal implants by stimulating electrodes with pulse
widths short enough to not elicit responses in neurons, but with their
combined pulse width adequate to activate a neuron in between them.
Abstract: Electrical discharge machining (EDM) is well
established machining technique mainly used to machine complex
geometries on difficult-to-machine materials and high strength
temperature resistant alloys. In the present research, the objective is
to study the shape of the electrode and establish the application of
liquid nitrogen in reducing distortion of the electrode during
electrical discharge machining of M2 grade high speed steel using
copper electrodes. Study of roundness was performed on the
electrode to observe the shape of the electrode for both conventional
EDM and EDM with cryogenically cooled electrode. Scanning
Electron Microscope (SEM) has been used to study the shape of
electrode tip. The effect of various parameters such as discharge
current and pulse on time has been studied to understand the behavior
of distortion of electrode. It has been concluded that the shape
retention is better in case of liquid nitrogen cooled electrode.
Abstract: In this paper two different Antilock braking system (ABS) are simulated and compared. One is the ordinary hydraulic ABS system which we call it ABS and the other is Electromagnetic Antilock braking system which is called (EMABS) the basis of performance of an EMABS is based upon Electromagnetic force. In this system there is no need to use servo hydraulic booster which are used in ABS system. In EMABS to generate the desired force we have use a magnetic relay which works with an input voltage through an air gap (g). The generated force will be amplified by the relay arm, and is applied to the brake shoes and thus the braking torque is generated. The braking torque is proportional to the applied electrical voltage E. to adjust the braking torque it is only necessary to regulate the electrical voltage E which is very faster and has a much smaller time constant T than the ABS system. The simulations of these two different ABS systems are done with MATLAB/SIMULINK software and the superiority of the EMABS has been shown.
Abstract: In this study we present the effect of elevated
temperatures from 300K to 400K on the electrical properties of
copper Phthalocyanine (CuPc) based organic field effect transistors
(OFET). Thin films of organic semiconductor CuPc (40nm) and
semitransparent Al (20nm) were deposited in sequence, by vacuum
evaporation on a glass substrate with previously deposited Ag source
and drain electrodes with a gap of 40 μm. Under resistive mode of
operation, where gate was suspended it was observed that drain
current of this organic field effect transistor (OFET) show an
increase with temperature. While in grounded gate condition metal
(aluminum) – semiconductor (Copper Phthalocyanine) Schottky
junction dominated the output characteristics and device showed
switching effect from low to high conduction states like Zener diode
at higher bias voltages. This threshold voltage for switching effect
has been found to be inversely proportional to temperature and shows
an abrupt decrease after knee temperature of 360K. Change in
dynamic resistance (Rd = dV/dI) with respect to temperature was
observed to be -1%/K.
Abstract: Nano fibers produced by electrospinning are of industrial and scientific attention due to their special characteristics such as long length, small diameter and high surface area. Applications of electrospun structures in nanotechnology are included tissue scaffolds, fibers for drug delivery, composite reinforcement, chemical sensing, enzyme immobilization, membrane-based filtration, protective clothing, catalysis, solar cells, electronic devices and others. Many polymer and ceramic precursor nano fibers have been successfully electrospun with diameters in the range from 1 nm to several microns. The process is complex so that fiber diameter is influenced by various material, design and operating parameters. The objective of this work is to apply genetic algorithm on the parameters of electrospinning which have the most significant effect on the nano fiber diameter to determine the optimum parameter values before doing experimental set up. Effective factors including initial polymer concentration, initial jet radius, electrical potential, relaxation time, initial elongation, viscosity and distance between nozzle and collector are considered to determine finest diameter which is selected by user.