Abstract: The optimal operation of proton exchange membrane fuel cell (PEMFC) requires good water management which is presented under two forms vapor and liquid. Moreover, fuel cells have to reach higher output require integration of some accessories which need electrical power. In order to analyze fuel cells operation and different species transport phenomena a biphasic mathematical model is presented by governing equations set. The numerical solution of these conservation equations is calculated by Matlab program. A multi-criteria optimization with weighting between two opposite objectives is used to determine the compromise solutions between maximum output and minimal stack size. The obtained results are in good agreement with available literature data.
Abstract: In this study, structural, mechanical, thermal and
electrical properties of poly (lactic acid) (PLA) nanocomposites with
low-loaded (0-1.5 wt%) untreated, heat and nitric acid treated multiwalled
carbon nanotubes (MWCNTs) were studied. Among the
composites, untreated 0.5 wt % MWCNTs and acid-treated 1.0 wt%
MWCNTs reinforced PLA show the tensile strength and modulus
values higher than the others. These two samples along with pure
PLA exhibit the stable orthorhombic α-form, whilst other samples
reveal the less stable orthorhombic β-form, as demonstrated by X-ray
diffraction study. Differential scanning calorimetry reveals the
evolution of the mentioned different phases by controlled cooling and
discloses an enhancement of PLA crystallization by nanotubes
incorporation. Thermogravimetric analysis shows that the MWCNTs
loaded sample degraded faster than PLA. Surface resistivity of the
nanocomposites is found to be dropped drastically by a factor of 1013
with a low loading of MWCNTs (1.5 wt%).
Abstract: Two-dimensional heat conduction within a composed solid material with a constant internal heat generation has been investigated numerically in a sector of the rotor a generator. The heat transfer between two adjacent materials is assumed to be purely conduction. Boundary conditions are assumed to be forced convection on the fluid side and adiabatic on symmetry lines. The control volume method is applied for the diffusion energy equation. Physical coordinates are transformed to the general curvilinear coordinates. Then by using a line-by-line method, the temperature distribution in a sector of the rotor has been determined. Finally, the results are normalized and the effect of cooling fluid on the maximum temperature of insulation is investigated.
Abstract: The operating control parameters of injection
flushing type of electrical discharge machining process on stainless
steel 304 workpiece with copper tools are being optimized
according to its individual machining characteristic i.e. material
removal rate (MRR). Lower MRR during EDM machining process
may decrease its- machining productivity. Hence, the quality
characteristic for MRR is set to higher-the-better to achieve the
optimum machining productivity. Taguchi method has been used
for the construction, layout and analysis of the experiment for each
of the machining characteristic for the MRR. The use of Taguchi
method in the experiment saves a lot of time and cost of preparing
and machining the experiment samples. Therefore, an L18
Orthogonal array which was the fundamental component in the
statistical design of experiments has been used to plan the
experiments and Analysis of Variance (ANOVA) is used to
determine the optimum machining parameters for this machining
characteristic. The control parameters selected for this
optimization experiments are polarity, pulse on duration, discharge
current, discharge voltage, machining depth, machining diameter
and dielectric liquid pressure. The result had shown that the higher
the discharge voltage, the higher will be the MRR.
Abstract: Insulation used in transformer is mostly oil pressboard insulation. Insulation failure is one of the major causes of catastrophic failure of transformers. It is established that partial discharges (PD) cause insulation degradation and premature failure of insulation. Online monitoring of PDs can reduce the risk of catastrophic failure of transformers. There are different techniques of partial discharge measurement like, electrical, optical, acoustic, opto-acoustic and ultra high frequency (UHF). Being non invasive and non interference prone, acoustic emission technique is advantageous for online PD measurement. Acoustic detection of p.d. is based on the retrieval and analysis of mechanical or pressure signals produced by partial discharges. Partial discharges are classified according to the origin of discharges. Their effects on insulation deterioration are different for different types. This paper reports experimental results and analysis for classification of partial discharges using acoustic emission signal of laboratory simulated partial discharges in oil pressboard insulation system using three different electrode systems. Acoustic emission signal produced by PD are detected by sensors mounted on the experimental tank surface, stored on an oscilloscope and fed to computer for further analysis. The measured AE signals are analyzed using discrete wavelet transform analysis and wavelet packet analysis. Energy distribution in different frequency bands of discrete wavelet decomposed signal and wavelet packet decomposed signal is calculated. These analyses show a distinct feature useful for PD classification. Wavelet packet analysis can sort out any misclassification arising out of DWT in most cases.
Abstract: In this research, a 2-D computational analysis of
steady state free convection in a rectangular enclosure filled with an
electrically conducting fluid under Effect of Magnetic Field has been
performed. The governing equations (mass, momentum, and energy)
are formulated and solved by a finite volume method (FVM)
subjected to different boundary conditions. A parametric study has
been conducted to consider the influence of Grashof number (Gr),
Prantdl number (Pr) and the orientation of magnetic field on the flow
and heat transfer characteristics. It is observed that Nusselt number
(Nu) and heat flux will increase with increasing Grashof and Prandtl
numbers and decreasing the slope of the orientation of magnetic field.
Abstract: Cardiac pulse-related artifacts in the EEG recorded
simultaneously with fMRI are complex and highly variable. Their
effective removal is an unsolved problem. Our aim is to develop an
adaptive removal algorithm based on the matching pursuit (MP)
technique and to compare it to established methods using a visual
evoked potential (VEP). We recorded the VEP inside the static
magnetic field of an MR scanner (with artifacts) as well as in an
electrically shielded room (artifact free). The MP-based artifact
removal outperformed average artifact subtraction (AAS) and
optimal basis set removal (OBS) in terms of restoring the EEG field
map topography of the VEP. Subsequently, a dipole model was fitted
to the VEP under each condition using a realistic boundary element
head model. The source location of the VEP recorded inside the MR
scanner was closest to that of the artifact free VEP after cleaning
with the MP-based algorithm as well as with AAS. While none of the
tested algorithms offered complete removal, MP showed promising
results due to its ability to adapt to variations of latency, frequency
and amplitude of individual artifact occurrences while still utilizing a
common template.
Abstract: The neural stimulation has been gaining much interest in neuromodulation research and clinical trials. For efficiency, there is a need for variable electrical stimulation such as current and voltage stimuli as well as wireless framework. In this regard, we develop the wireless neural stimulator capable of voltage and current stimuli. The system consists of ZigBee which is a wireless communication module and stimulus generator. The stimulus generator with 8-bits resolution enable both mono-polar and bi-polar waveform in voltage (-3.3~3.3V) and current(-330~330µA) stimulus mode which is controllable. The experimental results suggest that the proposed neural stimulator can play a role as an effective approach for neuromodulation.
Abstract: in this work, we present a new strategy of direct adaptive control denoted: Extended minimal controller synthesis (EMCS). This algorithm is designed for an induction motor, which includes both electrical and mechanical dynamics under the assumptions of linear magnetic circuits. The main motivation of the EMCS control is to enhance the robustness of the MRAC algorithms, i.e. the rejection of bounded effects of rapidly varying external disturbances.
Abstract: Indium-tin oxide films are deposited by low plasma
temperature RF sputtering on highly flexible modification of glycol
polyethyleneterephtalate substrates. The produced layers are
characterized with transparency over 82 % and sheet resistance of
86.9 Ω/square. The film’s conductivity was further improved by
additional UV illumination from light source (365 nm), having power
of 250 W. The influence of the UV exposure dose on the structural
and electro-optical properties of ITO was investigated. It was
established that the optimum time of illumination is 10 minutes and
further UV treatment leads to polymer substrates degradation.
Structural and bonds type analysis show that at longer treatment
carbon atoms release and diffuse into ITO films, which worsen their
electrical behavior. For the optimum UV dose the minimum sheet
resistance was measured to be 19.2 Ω/square, and the maximum
transparency remained almost unchanged – above 82 %.
Abstract: High voltage generators are being subject to higher
voltage rating and are being designed to operate in harsh conditions.
Stator windings are the main component of generators in which
Electrical, magnetical and thermal stresses remain major failures for
insulation degradation accelerated aging. A large number of
generators failed due to stator winding problems, mainly insulation
deterioration. Insulation degradation assessment plays vital role in the
asset life management. Mostly the stator failure is catastrophic
causing significant damage to the plant. Other than generation loss,
stator failure involves heavy repair or replacement cost. Electro
thermal analysis is the main characteristic for improvement design of
stator slot-s insulation. Dielectric parameters such as insulation
thickness, spacing, material types, geometry of winding and slot are
major design consideration. A very powerful method available to
analyze electro thermal performance is Finite Element Method
(FEM) which is used in this paper. The analysis of various stator coil
and slot configurations are used to design the better dielectric system
to reduce electrical and thermal stresses in order to increase the
power of generator in the same volume of core. This paper describes
the process used to perform classical design and improvement
analysis of stator slot-s insulation.
Abstract: This paper presents the experimental results of the
investigation of various properties related to the durability and longterm
performance of mortars made of Fly Ash blended cement, FA
and Ordinary Portland cement, OPC. The properties that were
investigated in an experimental program include; equilibration of
specimen in different relative humidity, determination of total
porosity, compressive strength, chloride permeability index, and
electrical resistivity. Fly Ash blended cement mortar specimens
exhibited 10% to 15% lower porosity when measured at equilibrium
conditions in different relative humidities as compared to the
specimens made of OPC mortar, which resulted in 6% to 8% higher
compressive strength of FA blended cement mortar specimens. The
effects of ambient relative humidity during sample equilibration on
porosity and strength development were also studied. For specimens
equilibrated in higher relative humidity conditions, such as 75%, the
total porosity of different mortar specimens was between 35% to 50%
less than the porosity of samples equilibrated in 12% relative
humidity, consequently leading to higher compressive strengths of
these specimens.A valid statistical correlation between values of
compressive strength, porosity and the degree of saturation was
obtained. Measured values of chloride permeability index of fly ash
blended cement mortar were obtained as one fourth to one sixth of
those measured for OPC mortar specimens, which indicates high
resistance against chloride ion penetration in FA blended cement
specimens, hence resulting in a highly durable mortar.
Abstract: This paper presents a silicon controller rectifier (SCR)
based ESD protection circuit for IC. The proposed ESD protection
circuit has low trigger voltage and high holding voltage compared with
conventional SCR ESD protection circuit. Electrical characteristics of
the proposed ESD protection circuit are simulated and analyzed using
TCAD simulator. The proposed ESD protection circuit verified
effective low voltage ESD characteristics with low trigger voltage and
high holding voltage.
Abstract: This paper presents a synthetic jet air blower actuated
by PZT for air blowing for air-breathing micro PEM fuel cell. The
several factors to affect the performance of air-breathing PEM fuel cell
such as air flow rate, opening ratio and cathode open type in the
cathode side were studied. Especially, an air flow rate is critical
condition to improve its performance. In this paper, we developed a
synthetic jet air blower to supply a high stoichiometric air flow. The
synthetic jet mechanism is a zero mass flux device that converts
electrical energy into the momentum. The synthetic jet actuation is
usually generated by a traditional PZT actuator, which consists of a
small cylindrical cavity, in/outlet channel and PZT diaphragms. The
flow rate of the fabricated synthetic jet air blower was 400cc/min at
550Hz and its power consumption was very low under 0.3W. The
proposed air-breathing PEM fuel cell which installed synthetic jet air
blower was higher performance and stability during continuous
operation than the air-breathing fuel cell without auxiliary device to
supply the air. The results showed that the maximum power density
was 188mW/cm2 at 400mA/cm2. This maximum power density and
durability were improved more than 40% and 20%, respectively.
Abstract: Fossil fuel-firing power plants dominate electric
power generation in Taiwan, which are also the major contributor to
Green House gases (GHG). CO2 is the most important greenhouse
gas that cause global warming. This paper penetrates the relationship
between carbon trading for GHG reduction and power generation
expansion planning (GEP) problem for the electrical utility. The
Particle Swarm Optimization (PSO) Algorithm is presented to deal
with the generation expansion planning strategy of the utility with
independent power providers (IPPs). The utility has to take both the
IPPs- participation and environment impact into account when a new
generation unit is considering expanded from view of supply side.
Abstract: Global approximation using metamodel for complex
mathematical function or computer model over a large variable
domain is often needed in sensibility analysis, computer simulation,
optimal control, and global design optimization of complex, multiphysics
systems. To overcome the limitations of the existing
response surface (RS), surrogate or metamodel modeling methods for
complex models over large variable domain, a new adaptive and
regressive RS modeling method using quadratic functions and local
area model improvement schemes is introduced. The method applies
an iterative and Latin hypercube sampling based RS update process,
divides the entire domain of design variables into multiple cells,
identifies rougher cells with large modeling error, and further divides
these cells along the roughest dimension direction. A small number
of additional sampling points from the original, expensive model are
added over the small and isolated rough cells to improve the RS
model locally until the model accuracy criteria are satisfied. The
method then combines local RS cells to regenerate the global RS
model with satisfactory accuracy. An effective RS cells sorting
algorithm is also introduced to improve the efficiency of model
evaluation. Benchmark tests are presented and use of the new
metamodeling method to replace complex hybrid electrical vehicle
powertrain performance model in vehicle design optimization and
optimal control are discussed.
Abstract: This paper proves that the problem of finding connected
vertex cover in a 2-connected planar graph ( CVC-2 ) with maximum degree 4 is NP-complete. The motivation for proving this result is to
give a shorter and simpler proof of NP-Completeness of TRA-MLC (the Top Right Access point Minimum-Length Corridor) problem [1], by finding the reduction from CVC-2. TRA-MLC has many applications in laying optical fibre cables for data communication and electrical wiring in floor plans.The problem of finding connected vertex cover in any planar graph ( CVC ) with maximum degree 4 is NP-complete [2]. We first show that CVC-2 belongs to NP and then we find a polynomial reduction from CVC to CVC-2. Let a graph G0 and an integer K form an instance of CVC, where G0 is a planar graph and K is an upper bound on the size of the connected vertex cover in G0. We construct a 2-connected planar graph, say G, by identifying the blocks and cut vertices of G0, and then finding the planar representation of all the blocks of G0, leading to a plane graph G1. We replace the cut vertices with cycles in such a way that the resultant graph G is a 2-connected planar graph with maximum
degree 4. We consider L = K -2t+3 t i=1 di where t is the number of cut vertices in G1 and di is the number of blocks for which ith cut vertex is common. We prove that G will have a connected vertex
cover with size less than or equal to L if and only if G0 has a connected vertex cover of size less than or equal to K.
Abstract: The daily increase of organic waste materials resulting
from different activities in the country is one of the main factors for
the pollution of environment. Today, with regard to the low level of
the output of using traditional methods, the high cost of disposal
waste materials and environmental pollutions, the use of modern
methods such as anaerobic digestion for the production of biogas has
been prevailing. The collected biogas from the process of anaerobic
digestion, as a renewable energy source similar to natural gas but
with a less methane and heating value is usable. Today, with the help
of technologies of filtration and proper preparation, access to biogas
with features fully similar to natural gas has become possible. At
present biogas is one of the main sources of supplying electrical and
thermal energy and also an appropriate option to be used in four
stroke engine, diesel engine, sterling engine, gas turbine, gas micro
turbine and fuel cell to produce electricity. The use of biogas for
different reasons which returns to socio-economic and environmental
advantages has been noticed in CHP for the production of energy in
the world. The production of biogas from the technology of anaerobic
digestion and its application in CHP power plants in Iran can not only
supply part of the energy demands in the country, but it can
materialize moving in line with the sustainable development. In this
article, the necessity of the development of CHP plants with biogas
fuels in the country will be dealt based on studies performed from the
economic, environmental and social aspects. Also to prove the
importance of the establishment of these kinds of power plants from
the economic point of view, necessary calculations has been done as
a case study for a CHP power plant with a biogas fuel.
Abstract: Monitoring and control of cane sugar crystallization
processes depend on the stability of the supersaturation (σ ) state.
The most widely used information to represent σ is the electrical
conductivity κ of the solutions. Nevertheless, previous studies point
out the shortcomings of this approach: κ may be regarded as
inappropriate to guarantee an accurate estimation of σ in impure
solutions. To improve the process control efficiency, additional
information is necessary. The mass of crystals in the solution ( c m )
and the solubility (mass ratio of sugar to water / s w m m ) are relevant
to complete information. Indeed, c m inherently contains information
about the mass balance and / s w m m contains information about the
supersaturation state of the solution. The main problem is that c m
and / s w m m are not available on-line. In this paper, a model based
soft-sensor is presented for a final crystallization stage (C sugar).
Simulation results obtained on industrial data show the reliability of
this approach, c m and the crystal content ( cc ) being estimated with
a sufficient accuracy for achieving on-line monitoring in industry
Abstract: When a lightning strike falls near an overhead power
line, the intense electromagnetic field radiated by the current of the
lightning return stroke coupled with power lines and there induced
transient overvoltages, which can cause a back-flashover in electrical
network. The indirect lightning represents a major danger owing to
the fact that it is more frequent than that which results from the direct
strikes.
In this paper we present an analysis of the electromagnetic
coupling between an external electromagnetic field generated by the
lightning and an electrical overhead lines, so we give an important
and original contribution: We are based on our experimental
measurements which we carried in the high voltage laboratories of
EPFL in Switzerland during the last trimester of 2005, on the recent
works of other authors and with our mathematical improvement a
new particular analytical expression of the electromagnetic field
generated by the lightning return stroke was developed and presented
in this paper. The results obtained by this new electromagnetic field
formulation were compared with experimental results and give a
reasonable approach.