Abstract: The increasing generation of saline wastewater through various industrial activities is becoming a global concern for activated sludge (AS) based biological treatment which is widely applied in wastewater treatment plants (WWTPs). As for the AS process, an increase in wastewater salinity has negative impact on its overall performance. The advent of conventional aerobic granular sludge (AGS) or bacterial AGS biotechnology has gained much attention because of its superior performance. The development of algal-bacterial AGS could enhance better nutrients removal, potentially reduce aeration cost through symbiotic algae-bacterial activity, and thus, can also reduce overall treatment cost. Nonetheless, the potential of salt stress to decrease biomass growth, microbial activity and nutrient removal exist. Up to the present, little information is available on saline wastewater treatment by algal-bacterial AGS. To the authors’ best knowledge, a comparison of the two AGS systems has not been done to evaluate nutrients removal capacity in the context of salinity increase. This study sought to figure out the impact of salinity on the algal-bacterial AGS system in comparison to bacterial AGS one, contributing to the application of AGS technology in the real world of saline wastewater treatment. In this study, the salt concentrations tested were 0 g/L, 1 g/L, 5 g/L, 10 g/L and 15 g/L of NaCl with 24-hr artificial illuminance of approximately 97.2 µmol m¯²s¯¹, and mature bacterial and algal-bacterial AGS were used for the operation of two identical sequencing batch reactors (SBRs) with a working volume of 0.9 L each, respectively. The results showed that salinity increase caused no apparent change in the color of bacterial AGS; while for algal-bacterial AGS, its color was progressively changed from green to dark green. A consequent increase in granule diameter and fluffiness was observed in the bacterial AGS reactor with the increase of salinity in comparison to a decrease in algal-bacterial AGS diameter. However, nitrite accumulation peaked from 1.0 mg/L and 0.4 mg/L at 1 g/L NaCl in the bacterial and algal-bacterial AGS systems, respectively to 9.8 mg/L in both systems when NaCl concentration varied from 5 g/L to 15 g/L. Almost no ammonia nitrogen was detected in the effluent except at 10 g/L NaCl concentration, where it averaged 4.2 mg/L and 2.4 mg/L, respectively, in the bacterial and algal-bacterial AGS systems. Nutrients removal in the algal-bacterial system was relatively higher than the bacterial AGS in terms of nitrogen and phosphorus removals. Nonetheless, the nutrient removal rate was almost 50% or lower. Results show that algal-bacterial AGS is more adaptable to salinity increase and could be more suitable for saline wastewater treatment. Optimization of operation conditions for algal-bacterial AGS system would be important to ensure its stably high efficiency in practice.
Abstract: Synthetic domestic wastewater was treated via combining treatment methods, including electrochemical oxidation, adsorption, and sequencing batch reactor (SBR). In the upper part of the reactor, an anode and a cathode (Ti/RuO2-IrO2) were organized in parallel for the electrochemical oxidation procedure. Sodium sulfate (Na2SO4) with a concentration of 2.5 g/L was applied as the electrolyte. The voltage and current were fixed on 7.50 V and 0.40 A, respectively. Then, 15% working value of the reactor was filled by activated sludge, and 85% working value of the reactor was added with synthetic wastewater. Powdered cockleshell, 1.5 g/L, was added in the reactor to do ion-exchange. Response surface methodology was employed for statistical analysis. Reaction time (h) and pH were considered as independent factors. A total of 97.0% biochemical oxygen demand, 99.9% phosphorous and 88.6% cadmium were eliminated at the optimum reaction time (80.0 min) and pH (6.4).
Abstract: In this study, Chevreul’s salt was dissolved in ammonium chloride solutions. All experiments were performed in a batch reactor. The obtained results were optimized. Parameters used in the experiments were the reaction temperature, the ammonium chloride concentration, the reaction time and the solid-to-liquid ratio. The optimum conditions were determined by 24 factorial experimental design method. The best values of four parameters were determined as based on the experiment results. After the evaluation of experiment results, all parameters were found as effective in experiment conditions selected. The optimum conditions on the maximum Chevreul’s salt dissolution were the ammonium chloride concentration 4.5 M, the reaction time 13.2 min., the reaction temperature 25 oC, and the solid-to-liquid ratio 9/80 g.mL-1. The best dissolution yield in these conditions was 96.20%.
Abstract: The study assessed the effectiveness of Pawpaw
(Carica papaya) wood in reducing the concentrations of heavy
metals in wastewater acting as a bio-sorbent. The following heavy
metals were considered; Zinc, Cadmium, Lead, Copper, Iron,
Selenium, Nickel and Manganese. The physiochemical properties of
Carica papaya stem were studied. The experimental sample was
sourced from the trunk of a felled matured pawpaw tree. Wastewater
for experimental use was prepared by dissolving soil samples
collected from a dump site at Owerri, Imo state of Nigeria in water.
The concentration of each metal remaining in solution as residual
metal after bio-sorption was determined using Atomic absorption
Spectrometer. The effects of pH and initial heavy metal concentration
were studied in a batch reactor. The results of Spectrometer test
showed that there were different functional groups detected in the
Carica papaya stem biomass. There was increase in metal removal as
the pH increased for all the metals considered except for Nickel and
Manganese. Optimum bio-sorption occurred at pH 5.9 with 5g/100ml
solution of bio-sorbent. The results of the study showed that the
treated wastewater is fit for irrigation purpose based on Canada
wastewater quality guideline for the protection of Agricultural
standard. This approach thus provides a cost effective and
environmentally friendly option for treating wastewater.
Abstract: The objective of this study is to investigate the performance of the electrocoagulation process for color and COD removal in palm oil wastewater using a 10 L batch reactor. Iron was used as electrodes and the distance between electrodes was 2 cm. The effects of operating parameters: current voltage (6, 12 and 18 volt), reaction time (5, 15, 30, 45 and 60 min) and initial pH (4 and 9) of treatment efficiency were examine. The result showed that decolorization and COD removal efficiency increased with the increase in current voltage and reaction time. The proper condition for decolorization achieved at initial pH 4 and 9 were current voltage of 12 volt, reaction time 30 min. The decolorization efficiency reached 90.4% and 88.9%, respectively. COD removal was achiveved at current voltage 12 volt, reaction time 15 min. COD removal efficiency was 89.2 % and 83.0%, respectively. From the results, to show electrocoagulation process can treat palm oil mill wastewater in both acidic and basic condition at high efficiency for color and COD removal. Consequently, electrocoagulation process can be used or applied as a post-treatment step to improve the quality of the final discharge in term of color and residual COD removal.
Abstract: This paper describes the application of a model
predictive controller to the problem of batch reactor temperature
control. Although a great deal of work has been done to improve
reactor throughput using batch sequence control, the control of the
actual reactor temperature remains a difficult problem for many
operators of these processes. Temperature control is important as
many chemical reactions are sensitive to temperature for formation of
desired products. This controller consist of two part (1) a nonlinear
control method GLC (Global Linearizing Control) to create a linear
model of system and (2) a Model predictive controller used to obtain
optimal input control sequence. The temperature of reactor is tuned
to track a predetermined temperature trajectory that applied to the
batch reactor. To do so two input signals, electrical powers and the
flow of coolant in the coil are used. Simulation results show that the
proposed controller has a remarkable performance for tracking
reference trajectory while at the same time it is robust against noise
imposed to system output.
Abstract: This paper describes the application of a model predictive controller to the problem of batch reactor temperature control. Although a great deal of work has been done to improve reactor throughput using batch sequence control, the control of the actual reactor temperature remains a difficult problem for many operators of these processes. Temperature control is important as many chemical reactions are sensitive to temperature for formation of desired products. This controller consist of two part (1) a nonlinear control method GLC (Global Linearizing Control) to create a linear model of system and (2) a Model predictive controller used to obtain optimal input control sequence. The temperature of reactor is tuned to track a predetermined temperature trajectory that applied to the batch reactor. To do so two input signals, electrical powers and the flow of coolant in the coil are used. Simulation results show that the proposed controller has a remarkable performance for tracking reference trajectory while at the same time it is robust against noise imposed to system output.
Abstract: Direct fermentation of 226 white rose tapioca stem to
ethanol by Fusarium oxysporum was studied in a batch reactor.
Fermentation of ethanol can be achieved by sequential pretreatment
using dilute acid and dilute alkali solutions using 100 mesh tapioca
stem particles. The quantitative effects of substrate concentration, pH
and temperature on ethanol concentration were optimized using a full
factorial central composite design experiment. The optimum process
conditions were then obtained using response surface methodology.
The quadratic model indicated that substrate concentration of 33g/l,
pH 5.52 and a temperature of 30.13oC were found to be optimum for
maximum ethanol concentration of 8.64g/l. The predicted optimum
process conditions obtained using response surface methodology was
verified through confirmatory experiments. Leudeking-piret model
was used to study the product formation kinetics for the production
of ethanol and the model parameters were evaluated using
experimental data.
Abstract: The conventional production of biodiesel from crude
palm oil which contains large amounts of free fatty acids in the
presence of a homogeneous base catalyst confronts the problems of
soap formation and very low yield of biodiesel. To overcome these
problems, free fatty acids must be esterified to their esters in the
presence of an acid catalyst prior to alkaline-catalyzed
transesterification. Sulfated metal oxides are a promising group of
catalysts due to their very high acidity. In this research, aluminadoped
sulfated tin oxide (SO4
2-/Al2O3-SnO2) catalysts were prepared
and used for esterification of free fatty acids in crude palm oil in a
batch reactor. The SO4
2-/Al2O3-SnO2 catalysts were prepared from
different Al precursors. The results showed that different Al
precursors gave different activities of the SO4
2-/Al2O3-SnO2 catalysts.
The esterification of free fatty acids in crude palm oil with methanol
in the presence of SO4
2-/Al2O3-SnO2 catalysts followed first-order
kinetics.
Abstract: A laboratory set-up was designed to survey the
effectiveness of UV/O3 advanced oxidation process (AOP) for the
removal of Carbaryl from polluted water in batch reactor. The study
was carried out by UV/O3 process for water samples containing 1 to
20 mg/L of Carbaryl in distilled water. Also the range of drinking
water resources adjusted in synthetic water and effects of contact
time, pH and Carbaryl concentration were studied. The residual
pesticide concentration was determined by applying high
performance liquid chromatography (HPLC). The results indicated
that increasing of retention time and pH, enhances pesticide removal
efficiency. The removal efficiency has been affected by pesticide
initial concentration. Samples with low pesticide concentration
showed a remarkable removal efficiency compared to the samples
with high pesticide concentration. AOP method showed the removal
efficiencies of 80% to 100%. Although process showed high
performance for removal of pesticide from water samples, this
process has different disadvantages including complication,
intolerability, difficulty of maintenance and equipmental and
structural requirements.