Abstract: This paper investigates vortex shedding processes
occurring at the end of a stack of parallel plates, due to an oscillating
flow induced by an acoustic standing wave within an acoustic
resonator. Here, Particle Image Velocimetry (PIV) is used to quantify
the vortex shedding processes within an acoustic cycle
phase-by-phase, in particular during the “ejection" of the fluid out of
the stack. Standard hot-wire anemometry measurement is also applied
to detect the velocity fluctuations near the end of the stack.
Combination of these two measurement techniques allowed a detailed
analysis of the vortex shedding phenomena. The results obtained show
that, as the Reynolds number varies (by varying the plate thickness
and drive ratio), different flow patterns of vortex shedding are
observed by the PIV measurement. On the other hand, the
time-dependent hot-wire measurements allow obtaining detailed
frequency spectra of the velocity signal, used for calculating
characteristic Strouhal numbers. The impact of the plate thickness and
the Reynolds number on the vortex shedding pattern has been
discussed. Furthermore, a detailed map of the relationship between the
Strouhal number and Reynolds number has been obtained and
discussed.
Abstract: KSLV-I(Korea Space Launch Vehicle-I) is designed as
a launch vehicle to enter a 100 kg-class satellite to the LEO(Low Earth
Orbit). Attitude angles of the upper-stage, including roll, pitch and
yaw are controlled by the cold gas thruster system using nitrogen gas.
The cold gas thruster is an actuator in the RCS(Reaction Control
System). To design an attitude controller for the upper-stage, thrust
measurement in vacuum condition is required. In this paper, the new
thrust measurement system and calibration mechanism are developed
and measurement errors and signal processing method are presented.
Abstract: This paper presents an experimental investigation of
transformer dielectric response and solid insulation water content.
The dielectric response was carried out on the base of Hybrid
Frequency Dielectric Spectroscopy and Polarization Current
measurements method (FDS &PC). The calculation of the water
content in paper is based on the water content in oil and the obtained
equilibrium curves. A reference measurements were performed at
equilibrium conditions for water content in oil and paper of
transformer at different stable temperatures (25, 50, 60 and 70°C) to
prepare references to evaluate the insulation behavior at the not
equilibrium conditions. Some measurements performed at the
different simulated normal working modes of transformer operation
at the same temperature where the equilibrium conditions. The
obtained results show that when transformer temperature is mach
more than the its ambient temperature, the transformer temperature
decreases immediately after disconnecting the transformer from the
network and this temperature reduction influences the transformer
insulation condition in the measuring process. In addition to the oil
temperature at the near places to the sensors, the temperature
uniformity in transformer which can be changed by a big change in
the load of transformer before the measuring time will influence the
result. The investigations have shown that the extremely influence of
the time between disconnecting the transformer and beginning the
measurements on the results. And the online monitoring for water
content in paper measurements, on the basis of the oil water content
on line monitoring and the obtained equilibrium curves. The
measurements where performed continuously and for about 50 days
without any disconnection in the prepared the adiabatic room.
Abstract: A new analysis of perceptual speech enhancement is
presented. It focuses on the fact that if only noise above the masking
threshold is filtered, then noise below the masking threshold, but
above the absolute threshold of hearing, can become audible after the
masker filtering. This particular drawback of some perceptual filters,
hereafter called the maskee-to-audible-noise (MAN) phenomenon,
favours the emergence of isolated tonals that increase musical noise.
Two filtering techniques that avoid or correct the MAN phenomenon
are proposed to effectively suppress background noise without introducing
much distortion. Experimental results, including objective
and subjective measurements, show that these techniques improve
the enhanced speech quality and the gain they bring emphasizes the
importance of the MAN phenomenon.
Abstract: The modeling of water transfer in the unsaturated zone
uses techniques and methods of the soil physics to solve the
Richards-s equation. However, there is a disaccord between the size
of the measurements provided by the soil physics and the size of the
fields of hydrological modeling problem, to which is added the
strong spatial variability of soil hydraulic properties. The objective of
this work was to develop a methodology to estimate the
hydrodynamic parameters for modeling water transfers at different
hydrological scales in the soil-plant atmosphere systems.
Abstract: The electrolyte stirring method of anodization etching
process for manufacturing porous silicon (PS) is reported in this work.
Two experimental setups of nature air stirring (PS-ASM) and
electrolyte stirring (PS-ESM) are employed to clarify the influence of
stirring mechanisms on electrochemical etching process. Compared to
traditional fabrication without any stirring apparatus (PS-TM), a large
plateau region of PS surface structure is obtained from samples with
both stirring methods by the 3D-profiler measurement. Moreover, the
light emission response is also improved by both proposed electrolyte
stirring methods due to the cycling force in electrolyte could
effectively enhance etch-carrier distribution while the electrochemical
etching process is made. According to the analysis of statistical
calculation of photoluminescence (PL) intensity, lower standard
deviations are obtained from PS-samples with studied stirring methods,
i.e. the uniformity of PL-intensity is effectively improved. The
calculated deviations of PL-intensity are 93.2, 74.5 and 64,
respectively, for PS-TM, PS-ASM and PS-ESM.
Abstract: In this article, using finite element analysis (FEA)
and an X-ray diffractometer (XRD), cold-sprayed titanium particles
on a steel substrate is investigated in term of cooling time and the
development of residual strains. Three cooling-down models of
sprayed particles after deposition stage are simulated and discussed:
the first model (m1) considers conduction effect to the substrate only,
the second model (m2) considers both conduction as well as
convection effect to the environment, and the third model (m3) which
is the same as the second model but with the substrate heated to a
near particle temperature before spraying. Thereafter, residual strains
developed in the third model is compared with the experimental
measurement of residual strains, which involved a Bruker D8
Advance Diffractometer using CuKa radiation (40kV, 40mA)
monochromatised with a graphite sample monochromator. For
deposition conditions of this study, a good correlation was found to
exist between the FEA results and XRD measurements of residual
strains.
Abstract: The distance protection mainly the impedance relay which is considered as the main protection for transmission lines can be subjected to impedance measurement error which is, mainly, due to the fault resistance and to the power fluctuation. Thus, the impedance relay may not operate for a short circuit at the far end of the protected line (case of the under reach) or operates for a fault beyond its protected zone (case of overreach). In this paper, an approach to fault detection by a distance protection, which distinguishes between the faulty conditions and the effect of overload operation mode, has been developed. This approach is based on the symmetrical components; mainly the negative sequence, and it is taking into account both the effect of fault resistance and the overload situation which both have an effect upon the reliability of the protection in terms of dependability for the former and security for the latter.
Abstract: In this paper we study different similarity based approaches for the development of QSAR model devoted to the prediction of activity of antiobesity drugs. Classical similarity approaches are compared regarding to dissimilarity models based on the consideration of the calculation of Euclidean distances between the nonisomorphic fragments extracted in the matching process. Combining the classical similarity and dissimilarity approaches into a new similarity measure, the Approximate Similarity was also studied, and better results were obtained. The application of the proposed method to the development of quantitative structure-activity relationships (QSAR) has provided reliable tools for predicting of inhibitory activity of drugs. Acceptable results were obtained for the models presented here.
Abstract: In this paper an extensive verification of the extraction
method (published earlier) that consistently accounts for self-heating
and Early effect to accurately extract both base and thermal resistance
of bipolar junction transistors is presented. The method verification is
demonstrated on advanced RF SiGe HBTs were the extracted results
for the thermal resistance are compared with those from another
published method that ignores the effect of Early effect on internal
base-emitter voltage and the extracted results of the base resistance
are compared with those determined from noise measurements. A
self-consistency of our method in the extracted base resistance and
thermal resistance using compact model simulation results is also
carried out in order to study the level of accuracy of the method.
Abstract: Regarding previous research studies it was concluded
that thin-walled fiber-cement composites are able to conduct electric
current under specific conditions. This property is ensured by using
of various kinds of carbon materials. Though carbon fibers are less
conductive than metal fibers, composites with carbon fibers were
evaluated as better current conductors than the composites with metal
fibers. The level of electric conductivity is monitored by the means of
impedance measurement of designed samples. These composites
could be used for a range of applications such as heating of
trafficable surfaces or shielding of electro-magnetic fields.
The aim of the present research was to design an element with the
ability to monitor internal processes in building structures and
prevent them from collapsing. As a typical element for laboratory
testing there was chosen a concrete column, which was repeatedly
subjected to load by simple pressure with continual monitoring of
changes in electrical properties.
Abstract: Elastic light single-scattering spectroscopy system
with a single optical fiber probe was employed to differentiate cancerous prostate tissue from non-cancerous prostate tissue ex-vivo just after radical prostatectomy. First, ELSSS spectra were acquired
from cancerous prostate tissue to define its spectral features. Then,
spectra were acquired from normal prostate tissue to define difference in spectral features between the cancerous and normal
prostate tissues. Of the total 66 tissue samples were evaluated from
nine patients by ELSSS system. Comparing of histopathology results
and ELSSS measurements revealed that sign of the spectral slopes of
cancerous prostate tissue is negative and non-cancerous tissue is positive in the wavelength range from 450 to 750 nm. Based on the
correlation between histopathology results and sign of the spectral
slopes, ELSSS system differentiates cancerous prostate tissue from
non- cancerous with a sensitivity of 0.95 and a specificity of 0.94.
Abstract: More and more natural disasters are happening every
year: floods, earthquakes, volcanic eruptions, etc. In order to reduce
the risk of possible damages, governments all around the world are
investing into development of Early Warning Systems (EWS) for
environmental applications. The most important task of the EWS is
identification of the onset of critical situations affecting environment
and population, early enough to inform the authorities and general
public. This paper describes an approach for monitoring of flood
protections systems based on machine learning methods. An
Artificial Intelligence (AI) component has been developed for
detection of abnormal dike behaviour. The AI module has been
integrated into an EWS platform of the UrbanFlood project (EU
Seventh Framework Programme) and validated on real-time
measurements from the sensors installed in a dike.
Abstract: This paper aims to fabricated high quality anodic
aluminum oxide (AAO) film by anodization method. AAO pore size,
pore density, and film thickness can be controlled in 10~500 nm,
108~1011 pore．cm-2, and 1~100 μm. AAO volume and surface area can
be computed based on structural parameters such as thickness, pore
size, pore density, and sample size. Base on the thetorical calculation,
AAO has 100 μm thickness with 15 nm, 60 nm, and 500 nm pore
diameters AAO surface areas are 1225.2 cm2, 3204.4 cm2, and 549.7
cm2, respectively. The large unit surface area which is useful for
adsorption application. When AAO adsorbed pH indictor of
bromphenol blue presented a sensitive pH detection of solution
change. This testing method can further be used for the precise
measurement of biotechnology, convenience measurement of
industrial engineering.
Abstract: The after–sales activities are nowadays acknowledged
as a relevant source of revenue, profit and competitive advantage in
most manufacturing industries. Top and middle management,
therefore, should focus on the definition of a structured business
performance measurement system for the after-sales business. The
paper aims at filling this gap, and presents an integrated methodology
for the after-sales network performance measurement, and provides
an empirical application to automotive case companies and their
official service network. This is the first study that presents an
integrated multivariate approach for total assessment and
improvement of after-sale services.
Abstract: This study reports the preparation of soft magnetic
ribbons of Fe-based amorphous alloys using the single-roller melt-spinning technique. Ribbon width varied from 142 mm to 213
mm and, with a thickness of approximately 22 μm ± 2 μm. The microstructure and magnetic properties of the ribbons were
characterized by differential scanning calorimeter (DSC), X-ray diffraction (XRD), vibrating sample magnetometer (VSM), and electrical resistivity measurements (ERM). The amorphous material
properties dependence of the cooling rate and nozzle pressure have uneven surface in ribbon thicknesses are investigated. Magnetic
measurement results indicate that some region of the ribbon exhibits good magnetic properties, higher saturation induction and lower coercivity. However, due to the uneven surface of 213 mm wide
ribbon, the magnetic responses are not uniformly distributed. To
understand the transformer magnetic performances, this study analyzes the measurements of a three-phase 2 MVA amorphous-cored transformer. Experimental results confirm that the transformer with a
ribbon width of 142 mm has better magnetic properties in terms of lower core loss, exciting power, and audible noise.
Abstract: Usually, the solid-fuel flow of an iron ore sinter plant
consists of different types of the solid-fuels, which differ from each
other. Information about the composition of the solid-fuel flow
usually comes every 8-24 hours. It can be clearly seen that this
information cannot be used to control the sintering process in real
time. Due to this, we propose an expert system which uses indirect
measurements from the process in order to obtain the composition of
the solid-fuel flow by solving an optimization task. Then this
information can be used to control the sintering process. The
proposed technique can be successfully used to improve sinter
quality and reduce the amount of solid-fuel used by the process.
Abstract: Power system state estimation is the process of
calculating a reliable estimate of the power system state vector
composed of bus voltages' angles and magnitudes from telemetered
measurements on the system. This estimate of the state vector
provides the description of the system necessary for the operation
and security monitoring. Many methods are described in the
literature for solving the state estimation problem, the most important
of which are the classical weighted least squares method and the nondeterministic
genetic based method; however both showed
drawbacks. In this paper a modified version of the genetic
algorithm power system state estimation is introduced, Sensitivity of
the proposed algorithm to genetic operators is discussed, the
algorithm is applied to case studies and finally it is compared with
the classical weighted least squares method formulation.
Abstract: In our recent study, we have used ZnO nanoparticles assisted with UV light irradiation to investigate the photocatalytic degradation of Phenol Red (PR). The ZnO photocatalyst was characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM), specific surface area analysis (BET) and UVvisible spectroscopy. X-ray diffractometry result for the ZnO nanoparticles exhibit normal crystalline phase features. All observed peaks can be indexed to the pure hexagonal wurtzite crystal structures, with the space group of P63mc. There are no other impurities in the diffraction peak. In addition, TEM measurement shows that most of the nanoparticles are rod-like and spherical in shape and fairly monodispersed. A significant degradation of the PR was observed when the catalyst was added into the solution even without the UV light exposure. In addition, the photodegradation increases with the photocatalyst loading. The surface area of the ZnO nanomaterials from the BET measurement was 11.9 m2/g. Besides the photocatalyst loading, the effect of some parameters on the photodegradation efficiency such as initial PR concentration and pH were also studied.
Abstract: Transport and logistics are the lifeblood of societies.
There is a strong correlation between overall growth in economic
activity and growth of transport. The movement of people and goods
has the potential for creating wealth and prosperity, therefore the
state of transportation infrastructure and especially the condition of
road networks is often a governmental priority. The design, building
and maintenance of national roads constitute a substantial share of
government budgets. Taking into account the magnitude and
importance of these investments, the expedience, efficiency and
sustainability of these projects are of great public interest. This paper
provides an overview of supply chain management principles applied
to road construction. In addition, road construction performance
measurement systems and ICT solutions are discussed. Road
construction in Estonia is analyzed. The authors propose the
development of a national performance measurement system for road
construction.