Abstract: This paper presents a new approach for the protection
of Thyristor-Controlled Series Compensator (TCSC) line using
Support Vector Machine (SVM). One SVM is trained for fault
classification and another for section identification. This method use
three phase current measurement that results in better speed and
accuracy than other SVM based methods which used single phase
current measurement. This makes it suitable for real-time protection.
The method was tested on 10,000 data instances with a very wide
variation in system conditions such as compensation level, source
impedance, location of fault, fault inception angle, load angle at
source bus and fault resistance. The proposed method requires only
local current measurement.
Abstract: This paper proposes the method combining artificial neural network with particle swarm optimization (PSO) to implement the maximum power point tracking (MPPT) by controlling the rotor speed of the wind generator. With the measurements of wind speed, rotor speed of wind generator and output power, the artificial neural network can be trained and the wind speed can be estimated. The proposed control system in this paper provides a manner for searching the maximum output power of wind generator even under the conditions of varying wind speed and load impedance.
Abstract: The flow field over a flat roof model building has been numerically investigated in order to determine threedimensional CFD guidelines for the calculation of the turbulent flow over a structure immersed in an atmospheric boundary layer. To this purpose, a complete validation campaign has been performed through a systematic comparison of numerical simulations with wind tunnel experimental data. Wind tunnel measurements and numerical predictions have been compared for five different vertical positions, respectively from the upstream leading edge to the downstream bottom edge of the analyzed model. Flow field characteristics in the neighborhood of the building model have been numerically investigated, allowing a quantification of the capabilities of the CFD code to predict the flow separation and the extension of the recirculation regions. The proposed calculations have allowed the development of a preliminary procedure to be used as guidance in selecting the appropriate grid configuration and corresponding turbulence model for the prediction of the flow field over a three-dimensional roof architecture dominated by flow separation.
Abstract: In this paper, the innovative intelligent fuzzy weighted
input estimation method (FWIEM) can be applied to the inverse heat
transfer conduction problem (IHCP) to estimate the unknown
time-varying heat flux efficiently as presented. The feasibility of this
method can be verified by adopting the temperature measurement
experiment. We would like to focus attention on the heat flux
estimation to three kinds of samples (Copper, Iron and Steel/AISI 304)
with the same 3mm thickness. The temperature measurements are then
regarded as the inputs into the FWIEM to estimate the heat flux. The
experiment results show that the proposed algorithm can estimate the
unknown time-varying heat flux on-line.
Abstract: The aim of this study is to identify the conditions of
implementation for reconfigurability in summarizing past flexible
manufacturing systems (FMS) research by drawing overall
conclusions from many separate High Performance Manufacturing
(HPM) studies. Meta-analysis will be applied to links between HPM
programs and their practices related to FMS and manufacturing
performance with particular reference to responsiveness performance.
More specifically, an application of meta-analysis will be made with
reference to two of the main steps towards the development of an
empirically-tested theory: testing the adequacy of the measurement of
variables and testing the linkages between the variables.
Abstract: This paper focuses on assessment of air pollution in Umm-Alhyman, Kuwait, which is located south to oil refineries, power station, oil field, and highways. The measurements were made over a period of four days in March and July in 2001, 2004, and 2008. The measured pollutants included methanated and nonmethanated hydrocarbons (MHC, NMHC), CO, CO2, SO2, NOX, O3, and PM10. Also, meteorological parameters were measured, which includes temperature, wind speed and direction, and solar radiation. Over the study period, data analysis showed increase in measured SO2, NOX and CO by factors of 1.2, 5.5 and 2, respectively. This is explained in terms of increase in industrial activities, motor vehicle density, and power generation. Predictions of the measured data were made by the ISC-AERMOD software package and by using the ISCST3 model option. Finally, comparison was made between measured data against international standards.
Abstract: Interaction of inorganic water-soluble salts and building stones is studied in the paper. Two types of sandstone and one type of spongillite as representatives of materials used in historical masonry are subjected to experimental testing. Within the performed experiments, measurement of moisture and chloride concentration profiles is done in order to get input data for computational inverse analysis. Using the inverse analysis, moisture diffusivity and chloride diffusion coefficient of investigated materials are accessed. Additionally, the effect of salt presence on water vapor storage is investigated using dynamic vapor sorption device. The obtained data represents valuable information for restoration of historical masonry and give evidence on the performance of studied stones in contact with water soluble salts.
Abstract: Here we report on the utilization of Laser-Induced
Breakdown Spectroscopy (LIBS) for determination of Quantum Dots
(QDs) in liquid solution. The process of optimization of experimental
conditions from choosing the carrier medium to application of colloid
QDs is described. The main goal was to get the best possible signal to
noise ratio.
The results obtained from the measurements confirmed the capability
of LIBS technique for qualitative and afterwards quantitative
determination of QDs in liquid solution.
Abstract: The measurements of 226Ra, 232Th and 40K using
gamma spectrometry and radon concentration and exhalation rates
measurements using solid state nuclear track (LR-115, Type-II
plastic) detectors are used to asses a first order exposure risk for the
persons residing in Fatehbad and Hissar districts of Western Haryana,
India. The concentration of Radium, Thorium and Potassium in the
soil samples varies from 13.37 Bq m-3 to 24.67 Bq m-3, 34.67 Bq m-3
to 67.34 Bq m-3 and 298.78 Bq m-3 to 405.67 Bq m-3 respectively
with average values of 18.78, 47.35 and 361.57 Bq m-3 respectively.
The radium equivalent activity (Raeq) calculated for the same soil
samples varies from 92.72 Bq m-3 to 140.6 Bq m-3 with an average
value of 111.80 Bq m-3. The values of absorbed dose and annual
effective dose (indoors and outdoors) are found to vary from 44.18
nGy h-1 to 65.23 nGy h-1, 0.22 mSv y-1 to 0.32 mSv y-1 and 0.05 mSv
y-1 to 0.08 mSv y-1 respectively. The radon concentration and
exhalation rates have also been reported. The radium equivalent
activities in all the soil samples were found to be lower than the limit
(370 Bq kg-1) set in the Organization for Economic Cooperation and
Development (OECD) report and the value of Hex in all the samples
is less than unity.
Abstract: Ability of accurate and reliable location estimation in
indoor environment is the key issue in developing great number of
context aware applications and Location Based Services (LBS).
Today, the most viable solution for localization is the Received
Signal Strength (RSS) fingerprinting based approach using wireless
local area network (WLAN). This paper presents two RSS
fingerprinting based approaches – first we employ widely used
WLAN based positioning as a reference system and then investigate
the possibility of using GSM signals for positioning. To compare
them, we developed a positioning system in real world environment,
where realistic RSS measurements were collected. Multi-Layer
Perceptron (MLP) neural network was used as the approximation
function that maps RSS fingerprints and locations. Experimental
results indicate advantage of WLAN based approach in the sense of
lower localization error compared to GSM based approach, but GSM
signal coverage by far outreaches WLAN coverage and for some
LBS services requiring less precise accuracy our results indicate that
GSM positioning can also be a viable solution.
Abstract: This paper describes WiPoD (Wireless Position
Detector) which is a pure software based location determination and
tracking (positioning) system. It uses empirical signal strength measurements from different wireless access points for mobile user
positioning. It is designed to determine the location of users having
802.11 enabled mobile devices in an 802.11 WLAN infrastructure
and track them in real time. WiPoD is the first main module in our
LBS (Location Based Services) framework. We tested K-Nearest
Neighbor and Triangulation algorithms to estimate the position of a
mobile user. We also give the analysis results of these algorithms for
real time operations. In this paper, we propose a supportable, i.e.
understandable, maintainable, scalable and portable wireless
positioning system architecture for an LBS framework. The WiPoD
software has a multithreaded structure and was designed and implemented with paying attention to supportability features and real-time constraints and using object oriented design principles. We also describe the real-time software design issues of a wireless positioning system which will be part of an LBS framework.
Abstract: An investigation of noise in a micro stepping motor is
considered to study in this article. Because of the trend towards higher
precision and more and more small 3C (including Computer,
Communication and Consumer Electronics) products, the micro
stepping motor is frequently used to drive the micro system or the
other 3C products. Unfortunately, noise in a micro stepped motor is
too large to accept by the customs. To depress the noise of a micro
stepped motor, the dynamic characteristics in this system must be
studied. In this article, a Visual Basic (VB) computer program speed
controlled micro stepped motor in a digital camera is investigated.
Karman KD2300-2S non-contract eddy current displacement sensor,
probe microphone, and HP 35670A analyzer are employed to analyze
the dynamic characteristics of vibration and noise in a motor. The
vibration and noise measurement of different type of bearings and
different treatment of coils are compared. The rotating components,
bearings, coil, etc. of the motor play the important roles in producing
vibration and noise. It is found that the noise will be depressed about
3~4 dB and 6~7 dB, when substitutes the copper bearing with plastic
one and coats the motor coil with paraffin wax, respectively.
Abstract: In this paper, algorithm estimating the blood pressure
was proposed using the pulse transit time (PTT) as a more convenient
method of measuring the blood pressure. After measuring ECG and
pressure pulse, and photoplethysmography, the PTT was calculated
from the acquired signals. Thereafter, the system to indirectly measure
the systolic pressure and the diastolic pressure was composed using
the statistic method. In comparison between the blood pressure
indirectly measured by proposed algorithm estimating the blood
pressure and real blood pressure measured by conventional
sphygmomanometer, the systolic pressure indicates the mean error of
±3.24mmHg and the standard deviation of 2.53mmHg, while the
diastolic pressure indicates the satisfactory result, that is, the mean
error of ±1.80mmHg and the standard deviation of 1.39mmHg. These
results are satisfied with the regulation of ANSI/AAMI for
certification of sphygmomanometer that real measurement error value
should be within the mean error of ±5mmHg and the standard
deviation of 8mmHg. These results are suggest the possibility of
applying to portable and long time blood pressure monitoring system
hereafter.
Abstract: The use of neural networks is popular in various
building applications such as prediction of heating load, ventilation
rate and indoor temperature. Significant is, that only few papers deal
with indoor carbon dioxide (CO2) prediction which is a very good
indicator of indoor air quality (IAQ). In this study, a data-driven
modelling method based on multilayer perceptron network for indoor
air carbon dioxide in an apartment building is developed.
Temperature and humidity measurements are used as input variables
to the network. Motivation for this study derives from the following
issues. First, measuring carbon dioxide is expensive and sensors
power consumptions is high and secondly, this leads to short
operating times of battery-powered sensors. The results show that
predicting CO2 concentration based on relative humidity and
temperature measurements, is difficult. Therefore, more additional
information is needed.
Abstract: Linear stochastic estimation and quadratic stochastic
estimation techniques were applied to estimate the entire velocity
flow-field of an open cavity with a length to depth ratio of 2. The
estimations were done through the use of instantaneous velocity
magnitude as estimators. These measurements were obtained by
Particle Image Velocimetry. The predicted flow was compared
against the original flow-field in terms of the Reynolds stresses and
turbulent kinetic energy. Quadratic stochastic estimation proved to be
more superior than linear stochastic estimation in resolving the shear
layer flow. When the velocity fluctuations were scaled up in the
quadratic estimate, both the time-averaged quantities and the
instantaneous cavity flow can be predicted to a rather accurate extent.
Abstract: A boundary layer wind tunnel facility has been
adopted in order to conduct experimental measurements of the flow field around a model of the Panorama Giustinelli Building, Trieste
(Italy). Information on the main flow structures has been obtained by means of flow visualization techniques and has been compared to the
numerical predictions of the vortical structures spread on top of the roof, in order to investigate the optimal positioning for a vertical-axis
wind energy conversion system, registering a good agreement between experimental measurements and numerical predictions.
Abstract: In a competitive production environment, critical
decision making are based on data resulted by random sampling of
product units. Efficiency of these decisions depends on data quality
and also their reliability scale. This point leads to the necessity of a
reliable measurement system. Therefore, the conjecture process and
analysing the errors contributes to a measurement system known as
Measurement System Analysis (MSA). The aim of this research is on
determining the necessity and assurance of extensive development in
analysing measurement systems, particularly with the use of
Repeatability and Reproducibility Gages (GR&R) to improve
physical measurements. Nowadays in productive industries,
repeatability and reproducibility gages released so well but they are
not applicable as well as other measurement system analysis
methods. To get familiar with this method and gain a feedback in
improving measurement systems, this survey would be on
“ANOVA" method as the most widespread way of calculating
Repeatability and Reproducibility (R&R).
Abstract: Many methods exist for either measuring or estimating
evaporation from free water surfaces. Evaporation pans provide one
of the simplest, inexpensive, and most widely used methods of
estimating evaporative losses. In this study, the rate of evaporation
starting from a water surface was calculated by modeling with
application to dams in wet, arid and semi arid areas in Algeria.
We calculate the evaporation rate from the pan using the energy
budget equation, which offers the advantage of an ease of use, but
our results do not agree completely with the measurements taken by
the National Agency of areas carried out using dams located in areas
of different climates. For that, we develop a mathematical model to
simulate evaporation. This simulation uses an energy budget on the
level of a vat of measurement and a Computational Fluid Dynamics
(Fluent). Our calculation of evaporation rate is compared then by the
two methods and with the measures of areas in situ.
Abstract: The acidity of different raw Jordanian clays
containing zeolite, bentonite, red and white kaolinite and diatomite
was characterized by means of temperature programmed desorption
(TPD) of ammonia, conversion of 2-methyl-3-butyn-2-ol (MBOH),
FTIR and BET-measurements. FTIR spectra proved presence of
silanol and bridged hydroxyls on the clay surface. The number of
acidic sites was calculated from experimental TPD-profiles. We
observed the decrease of surface acidity correlates with the decrease
of Si/Al ratio except for diatomite. On the TPD-plot for zeolite two
maxima were registered due to different strength of surface acidic
sites. Values of MBOH conversion, product yields and selectivity
were calculated for the catalysis on Jordanian clays. We obtained that
all clay samples are able to convert MBOH into a major product
which is 3-methyl-3-buten-1-yne (MBYNE) catalyzed by acid
surface sites with the selectivity close to 70%. There was found a
correlation between MBOH conversion and acidity of clays
determined by TPD-NH3, i.e. the higher the acidity the higher the
conversion of MBOH. However, diatomite provided the lowest
conversion of MBOH as result of poor polarization of silanol groups.
Comparison of surface areas and conversions revealed the highest
density of active sites for red kaolinite and the lowest for zeolite and
diatomite.
Abstract: The feasibility of applying a simple and cost effective sliding friction testing apparatus to study the friction behaviour of a clutch facing material, effected by the variation of temperature and contact pressure, was investigated. It was found that the method used in this work was able to give a convenient and cost effective measurement of friction coefficients and their transitions of a clutch facing material. The obtained results will be useful for the development process of new facing materials.