Abstract: This paper presents a study of laminar to turbulent transition on a profile specifically designed for wind turbine blades, the DU91-W2-250, which belongs to a class of wind turbine dedicated airfoils, developed by Delft University of Technology. A comparison between the experimental behavior of the airfoil studied at Delft wind tunnel and the numerical predictions of the commercial CFD solver ANSYS FLUENT® has been performed. The prediction capabilities of the Spalart-Allmaras turbulence model and of the γ-θ Transitional model have been tested. A sensitivity analysis of the numerical results to the spatial domain discretization has also been performed using four different computational grids, which have been created using the mesher GAMBIT®. The comparison between experimental measurements and CFD results have allowed to determine the importance of the numerical prediction of the laminar to turbulent transition, in order not to overestimate airfoil friction drag due to a fully turbulent-regime flow computation.
Abstract: The flow field over a flat roof model building has been numerically investigated in order to determine threedimensional CFD guidelines for the calculation of the turbulent flow over a structure immersed in an atmospheric boundary layer. To this purpose, a complete validation campaign has been performed through a systematic comparison of numerical simulations with wind tunnel experimental data. Wind tunnel measurements and numerical predictions have been compared for five different vertical positions, respectively from the upstream leading edge to the downstream bottom edge of the analyzed model. Flow field characteristics in the neighborhood of the building model have been numerically investigated, allowing a quantification of the capabilities of the CFD code to predict the flow separation and the extension of the recirculation regions. The proposed calculations have allowed the development of a preliminary procedure to be used as guidance in selecting the appropriate grid configuration and corresponding turbulence model for the prediction of the flow field over a three-dimensional roof architecture dominated by flow separation.
Abstract: A boundary layer wind tunnel facility has been
adopted in order to conduct experimental measurements of the flow field around a model of the Panorama Giustinelli Building, Trieste
(Italy). Information on the main flow structures has been obtained by means of flow visualization techniques and has been compared to the
numerical predictions of the vortical structures spread on top of the roof, in order to investigate the optimal positioning for a vertical-axis
wind energy conversion system, registering a good agreement between experimental measurements and numerical predictions.
Abstract: The flow filed around a flatted-roof compound has
been investigated by means of 2D and 3D numerical simulations. A
constant wind velocity profile, based both on the maximum reference
wind speed in the building site (peak gust speed worked out for a 50-
year return period) and on the local roughness coefficient, has been
simulated in order to determine the wind-induced loads on top of the
roof. After determining the influence of the incoming wind directions
on the induced roof loads, a 2D analysis of the most severe load
condition has been performed, achieving a numerical quantification
of the expected wind-induced forces on the PV panels on top of the
roof.
Abstract: The flow field around a flat plate of infinite span has
been investigated for several values of the angle of attack. Numerical
predictions have been compared to experimental measurements, in
order to examine the effect of turbulence model and grid resolution
on the resultant aerodynamic forces acting on the plate. Also the
influence of the free-stream turbulence intensity, at the entrance of
the computational domain, has been investigated. A full campaign of
simulations has been conducted for three inclination angles (9°, 15°
and 30°), in order to obtain some practical guidelines to be used for
the simulation of the flow field around inclined plates and discs.
Abstract: The present study aims to evaluating the effect of
rotor solidity - in terms of chord length for a given rotor diameter - on
the performances of a small vertical axis Darrieus wind turbine. The
proposed work focuses on both power production and rotor power
coefficient, considering also the structural constraints deriving from
the centrifugal forces due to rotor angular velocity. Also the
smoothness of the resulting power curves have been investigated, in
order to evaluate the controllability of the corresponding rotor
architectures.
Abstract: This paper presents a numerical analysis of the
performance of a three-bladed Darrieus vertical-axis wind turbine
based on the DU91-W2-250 airfoil. A complete campaign of 2-D
simulations, performed for several values of tip speed ratio and based
on RANS unsteady calculations, has been performed to obtain the
rotor torque and power curves. Rotor performances have been
compared with the results of a previous work based on the use of the
NACA 0021 airfoil. Both the power coefficient and the torque
coefficient have been determined as a function of the tip speed ratio.
The flow field around rotor blades has also been analyzed. As a final
result, the performance of the DU airfoil based rotor appears to be
lower than the one based on the NACA 0021 blade section. This
behavior could be due to the higher stall characteristics of the NACA
profile, being the separation zone at the trailing edge more extended
for the DU airfoil.
Abstract: A multiple-option analytical model for the evaluation of the energy performance and distribution of aerodynamic forces acting on a vertical-axis Darrieus wind turbine depending on both rotor architecture and operating conditions is presented. For this purpose, a numerical algorithm, capable of generating the desired rotor conformation depending on design geometric parameters, is coupled to a Single/Double-Disk Multiple-Streamtube Blade Element – Momentum code. Both single and double-disk configurations are analyzed and model predictions are compared to literature experimental data in order to test the capability of the code for predicting rotor performance. Effective airfoil characteristics based on local blade Reynolds number are obtained through interpolation of literature low-Reynolds airfoil databases. Some corrections are introduced inside the original model with the aim of simulating also the effects of blade dynamic stall, rotor streamtube expansion and blade finite aspect ratio, for which a new empirical relationship to better fit the experimental data is proposed. In order to predict also open field rotor operation, a freestream wind shear profile is implemented, reproducing the effect of atmospheric boundary layer.
Abstract: A preliminary evaluation of the feasibility of installing small wind turbines on offshore oil and gas extraction platforms is presented. Some aerodynamic considerations are developed in order to determine the best rotor architecture to exploit the wind potential on such installations, assuming that wind conditions over the platforms are similar to those registered on the roofs of urban buildings. Economical considerations about both advantages and disadvantages of the exploitation of wind energy on offshore extraction platforms with respect to conventional offshore wind plants, is also presented. Finally, wind charts of European offshore winds are presented together with a map of the major offshore installations.
Abstract: Nuclear energy sources have been widely used in the
past decades in order to power spacecraft subsystems. Nevertheless,
their use has attracted controversy because of the risk of harmful
material released into the atmosphere if an accident were to occur
during the launch phase of the mission, leading to the general
adoption of photovoltaic systems.
As compared to solar cells, wind turbines have a great advantage
on Mars, as they can continuously produce power both during dust
storms and at night-time: this paper focuses on the potential of a wind
energy conversion system (WECS) considering the atmospheric
conditions on Mars. Wind potential on Martian surface has been
estimated, as well as the average energy requirements of a Martian
probe or surface rover. Finally, the expected daily energy output of
the WECS has been computed on the basis of both the swept area of
the rotor and the equivalent wind speed at the landing site.
Abstract: This paper presents a CFD analysis of the flow around
a 30° inclined flat plate of infinite span. Numerical predictions have
been compared to experimental measurements, in order to assess the
potential of the finite volume code of determining the aerodynamic
forces acting on a flat plate invested by a fluid stream of infinite
extent.
Several turbulence models and spatial node distributions have
been tested and flow field characteristics in the neighborhood of the
flat plate have been numerically investigated, allowing the
development of a preliminary procedure to be used as guidance in
selecting the appropriate grid configuration and the corresponding
turbulence model for the prediction of the flow field over a twodimensional
inclined plate.
Abstract: This paper presents a numerical investigation of the
unsteady flow around an American 19th century vertical-axis
windmill: the Stevens & Jolly rotor, patented on April 16, 1895. The
computational approach used is based on solving the complete
transient Reynolds-Averaged Navier-Stokes (t-RANS) equations: a
full campaign of numerical simulation has been performed using the
k-ω SST turbulence model. Flow field characteristics have been
investigated for several values of tip speed ratio and for a constant
unperturbed free-stream wind velocity of 6 m/s, enabling the study of
some unsteady flow phenomena in the rotor wake. Finally, the global
power generated from the windmill has been determined for each
simulated angular velocity, allowing the calculation of the rotor
power-curve.
Abstract: The optimal grid spacing and turbulence model for the
2D numerical analysis of a vertical-axis water turbine (VAWaterT)
operating in a 2 m/s freestream current has been investigated. The
results of five different spatial domain discretizations and two
turbulence models (k-ω SST and k-ε RNG) have been compared, in
order to gain the optimal y+ parameter distribution along the blade
walls during a full rotor revolution. The resulting optimal mesh has
appeared to be quite similar to that obtained for the numerical
analysis of a vertical-axis wind turbine.
Abstract: This paper presents an evaluation of the wind potential in the area of the Lagoon of Venice (Italy). A full anemometric campaign of 2 year measurements, performed by the "Osservatorio Bioclimatologico dell'Ospedale al Mare di Venezia" has been analyzed to obtain the Weibull wind speed distribution and the main wind directions. The annual energy outputs of two candidate horizontal-axis wind turbines (“Aventa AV-7 LoWind" and “Gaia Wind 133-11kW") have been estimated on the basis of the computed Weibull wind distribution, registering a better performance of the former turbine, due to a higher ratio between rotor swept area and rated power of the electric generator, determining a lower cut-in wind speed.
Abstract: This paper presents a numerical analysis of the
performance of a five-bladed Darrieus vertical-axis water turbine,
based on the NACA 0025 blade profile, for both bare and shrouded
configurations. A complete campaign of 2-D simulations, performed
for several values of tip speed ratio and based on RANS unsteady
calculations, has been performed to obtain the rotor torque and power
curves. Also the effect of a NACA-shaped central hydrofoil has been
investigated, with the aim of evaluating the impact of a solid
blockage on the performance of the shrouded rotor configuration.
The beneficial effect of the shroud on rotor overall performances
has clearly been evidenced, while the adoption of the central
hydrofoil has proved to be detrimental, being the resulting flow slow
down (due to the presence of the obstacle) much higher with respect
to the flow acceleration (due to the solid blockage effect).
Abstract: This paper presents a means for reducing the torque
variation during the revolution of a vertical-axis water turbine
(VAWaterT) by increasing the blade number. For this purpose, twodimensional
CFD analyses have been performed on a straight-bladed
Darrieus-type rotor. After describing the computational model and
the relative validation procedure, a complete campaign of
simulations, based on full RANS unsteady calculations, is proposed
for a three, four and five-bladed rotor architectures, characterized by
a NACA 0025 airfoil. For each proposed rotor configuration, flow
field characteristics are investigated at several values of tip speed
ratio, allowing a quantification of the influence of blade number on
flow geometric features and dynamic quantities, such as rotor torque
and power. Finally, torque and power curves are compared for the
three analyzed architectures, achieving a quantification of the effect
of blade number on overall rotor performance.
Abstract: The wind resource in the Italian site of Lendinara
(RO) is analyzed through a systematic anemometric campaign
performed on the top of the bell tower, at an altitude of over 100 m
above the ground. Both the average wind speed and the Weibull
distribution are computed. The resulting average wind velocity is in
accordance with the numerical predictions of the Italian Wind Atlas,
confirming the accuracy of the extrapolation of wind data adopted for
the evaluation of wind potential at higher altitudes with respect to the
commonly placed measurement stations.