Abstract: In this investigation, activity concentration of 226Ra, 232Th, and 40K, of some ceramic tile materials used in the local market of Jordan for interior decoration were determined by making use of High Purity Germanium (HPGe) detector. Twenty samples of different country of origin and sizes used in Jordan were analyzed. The concentration values of the last-mentioned radionuclides ranged from 30 Bq.kg-1 (Sample from Jordan) to 98 Bq.kg-1 (Sample from China) for 226Ra, 31 Bq.kg-1 (Sample from Italy) to 98 Bq.kg-1 (Sample from China) for 232Th, and 129 Bq.kg-1 (Sample from Spain) to 679 Bq.kg-1 (Sample from Italy) for 40K. Based on the calculated activity concentrations, some radiological parameters have been calculated to test the radiation hazards in the ceramic tiles. In this work, the following parameters: Total absorbed dose rate (DR), Annual effective dose rate (HR), Radium equivalent activity (Raeq), Radon emanation coefficient F (%) and Radon mass exhalation rate (Em) were calculated for all ceramic tiles and listed in the body of the work. Fortunately, the average calculated values of all parameters are less than the recommended values for each parameter. Consequently, almost all the examined ceramic materials appear to have low radon emanation coefficients. As a result of that investigation, no problems on people can appear by using those ceramic tiles in Jordan.
Abstract: Percentage of soil-gas radon-222 concentration (222Rn) from soil-depths contributing to outdoor radon atmospheric level depends largely on some physical parameters of the soil. To determine its dependency in soil-depths, survey tests were carried out on soil depths and grain size particles using in-situ measurement method of soil-gas radon-222 concentration at different soil depths. The measurements were carried out with an electronic active radon detector (RAD-7) manufactured by Durridge Company USA. Radon-222 concentrations (222Rn) in soil-gas were measured at four different soil depths of 20, 40, 60 and 100 cm in five feasible locations. At each soil depth, soil samples were collected for grain size particle analysis using soil grasp sampler. The result showed that highest value of radon-222 concentration (24,680 ± 1960 Bqm-3) was measured at 100 cm depth with utmost grain size particle of 17.64% while the lowest concentration (7370 ± 1139 Bqm-3) was measured at 100 cm depth with least grain size particle of 10.75% respectively. A computational model was derived using SPSS regression package. This model could be a yardstick for prediction on soil gas radon concentration reference to soil grain size particle at different soil-depths.
Abstract: In recent years, interest in ecogenetic and biomedical problems related to the effects on the population of radon and its daughter decay products has increased significantly. Of particular interest is the assessment of the consequence of irradiation at hazardous radon areas, which includes the Almaty region due to the large number of tectonic faults that enhance radon emanation. In connection with the foregoing, the purpose of this work was to study the genetic effects of exposure to supernormal radon doses on the alpha-radiation model. Irradiation does not affect the growth of the cell, but rather its ability to differentiate. In addition, irradiation can lead to somatic mutations, morphoses and modifications. These damages most likely occur from changes in the composition of the substances of the cell. Such changes are epigenetic since they affect the regulatory processes of ontogenesis. Variability in the expression of regulatory genes refers to conditional mutations that modify the formation of signs of intraspecific similarity. Characteristic features of these conditional mutations are the dominant type of their manifestation, phenotypic asymmetry and their instability in the generations. Currently, the terms “morphosis” and “modification” are used to describe epigenetic variability, which are maintained in Drosophila melanogaster cultures using linkaged X- chromosomes, and the mutant X-chromosome is transmitted along the paternal line. In this paper, we investigated the epigenetic effects of alpha particles, whose source in nature is mainly radon and its daughter decay products. In the experiment, an isotope of plutonium-238 (Pu238), generating radiation with an energy of about 5500 eV, was used as a source of alpha particles. In an experiment in the first generation (F1), deformities or morphoses were found, which can be called "radiation syndromes" or mutations, the manifestation of which is similar to the pleiotropic action of genes. The proportion of morphoses in the experiment was 1.8%, and in control 0.4%. In this experiment, the morphoses in the flies of the first and second generation looked like black spots, or melanomas on different parts of the imago body; "generalized" melanomas; curled, curved wings; shortened wing; bubble on one wing; absence of one wing, deformation of thorax, interruption and violation of tergite patterns, disruption of distribution of ocular facets and bristles; absence of pigmentation of the second and third legs. Statistical analysis by the Chi-square method showed the reliability of the difference in experiment and control at P ≤ 0.01. On the basis of this, it can be considered that alpha particles, which in the environment are mainly generated by radon and its isotopes, have a mutagenic effect that manifests itself, mainly in the formation of morphoses or deformities.
Abstract: The production of low cost and environmentally friendly products represents an important step for developing countries. Biomass is one of the largest renewable energy sources, and Serbia is among the top European countries in terms of the amount of available and unused biomass. Substituting cement with the ashes obtained by the combustion of biomass would reduce the negative impact of concrete industry on the environment and would provide a waste valorization by the reuse of this type of by-product in mortars and concretes manufacture. The study contains data on physical properties, chemical characteristics and pozzolanic properties of obtained biomass ashes: wheat straw ash and mixture of wheat and soya straw ash in Serbia, which were, later, used as supplementary cementitious materials in preparation of mortars. Experimental research of influence of biomass ashes on physical and mechanical properties of cement mortars was conducted. The results indicate that the biomass ashes can be successfully used in mortars as substitutes of cement without compromising their physical and mechanical performances.
Abstract: The Ko Samui district of Surat Thani province is located in the high amounts of equivalent uranium in the ground surface that is the source of radon. Our research in the Ko Samui district aimed at comparing the indoor radon concentrations between dwellings and workplaces. Measurements of indoor radon concentrations were carried out in 46 dwellings and 127 workplaces, using CR-39 alpha-track detectors in closed-cup. A total of 173 detectors were distributed in 7 sub-districts. The detectors were placed in bedrooms of dwellings and workrooms of workplaces. All detectors were exposed to airborne radon for 90 days. After exposure, the alpha tracks were made visible by chemical etching before they were manually counted under an optical microscope. The track densities were assumed to be correlated with the radon concentration levels. We found that the radon concentrations could be well described by a log-normal distribution. Most concentrations (37%) were found in the range between 16 and 30 Bq.m-3. The radon concentrations in dwellings and workplaces varied from a minimum of 11 Bq.m-3 to a maximum of 305 Bq.m-3. The minimum (11 Bq.m-3) and maximum (305 Bq.m-3) values of indoor radon concentrations were found in a workplace and a dwelling, respectively. Only for four samples (3%), the indoor radon concentrations were found to be higher than the reference level recommended by the WHO (100 Bq.m-3). The overall geometric mean in the surveyed area was 32.6±1.65 Bq.m-3, which was lower than the worldwide average (39 Bq.m-3). The statistic comparison of the geometric mean indoor radon concentrations between dwellings and workplaces showed that the geometric mean in dwellings (46.0±1.55 Bq.m-3) was significantly higher than in workplaces (28.8±1.58 Bq.m-3) at the 0.05 level. Moreover, our study found that the majority of the bedrooms in dwellings had a closed atmosphere, resulting in poorer ventilation than in most of the workplaces that had access to air flow through open doors and windows at daytime. We consider this to be the main reason for the higher geometric mean indoor radon concentration in dwellings compared to workplaces.
Abstract: The aim of this study is to evaluate the efficacy of radon remedial action in a school on the Ischia island, South Italy, affected by indoor radon concentration higher than the value of 500 Bq/m3. This value is the limit imposed by the Italian legislation, to above which corrective actions in schools are necessary. Before the application of remedial action, indoor radon concentrations were measured in 9 rooms of the school. The measurements were performed with LR-115 passive alpha detectors (SSNTDs) and E-Perm. The remedial action was conducted in one of the office affected by high radon concentration using a Radonstop paint applied after the construction of a concrete slab under the floor. The effect of remedial action was the reduction of the concentration of radon of 41% and moreover it has demonstrated to be durable over time. The chosen method is cheap and easy to apply and it could be designed for various types of building. This method can be applied to new and existing buildings that show high dose values.
Abstract: Usually, phosphate deposits contain 238U and 232Th in addition to their decay products. Due to their different pathways in the environment, the 238U/232Th activity concentration ratio usually found to be greater than unity in phosphate sediments. The presence of these radionuclides creates a potential need to control exposure of workers in the mining and processing activities of the phosphate minerals in accordance with IAEA safety standards. The greatest dose to workers comes from exposure to radon, especially 222Rn from the uranium series, and has to be controlled. In this regard, radon (222Rn) was measured in the atmosphere (indoor and outdoor) of Al-Jalamid phosphate-mines working area using a portable radon-measurement instrument RAD7, in a purpose of radiation protection. Radon was measured in 61 sites inside the open phosphate mines, the phosphate upgrading facility (offices and rooms of the workers, and in some open-air sites) and in the dwellings of the workers residence-village that lies at about 3 km from the mines working area. The obtained results indicated that the average indoor radon concentration was about 48.4 Bq/m3. Inside the upgrading facility, the average outdoor concentrations were 10.8 and 9.7 Bq/m3 in the concentrate piles and crushing areas, respectively. It was 12.3 Bq/m3 in the atmosphere of the open mines. These values are comparable with the global average values. Based on the average values, the annual effective dose due to radon inhalation was calculated and risk estimates have been done. The average annual effective dose to workers due to the radon inhalation was estimated by 1.32 mSv. The potential excess risk of lung cancer mortality that could be attributed to radon, when considering the lifetime exposure, was estimated by 53.0x10-4. The results have been discussed in detail.
Abstract: Radon is a radioactive gas emitted from radium, a daughter product of uranium that occurs naturally in rocks and soil. Radon, together with its decay products, emits alpha particles that can damage lung tissue. The activity concentration of 222Ra has been analyzed in water samples collected from borewells and rivers in and around Hassan city, Karnataka State, India. The measurements were performed by Emanometry technique. The concentration of 222Rn in borewell waters varies from 18.49±1.89 to 397.26±12.3 Bql-1 with geometric mean 120.48±12.87 Bql-1 and in river waters it varies from 92.63±9.31 to 93.98±9.51 Bql-1 with geometric mean of 93.16±9.33 Bql-1. In the present study, the radon concentrations are higher in Adarshanagar and Viveka Nagar which are found to be 397.26±12.3 Bql-1 and 325.78±32.56 Bql-1. Most of the analysed samples show a 222Rn concentration more than 100 Bql-1 and this can be attributed to the geology of the area where the ground waters are located, which is predominantly of granitic characteristic. The average inhalation dose and ingestion dose in the borewell water are found to be 0.405 and 0.033 µSvy-1; and in river water it is found to be 0.234 and 0.019 µSvy-1, respectively. The average total effective dose rate in borewell waters and river waters are found to be 0.433 and 0.253 µSvy-1, which does not cause any health risk to the population of Hassan region.
Abstract: Design criteria for achieving an acceptable indoor radon concentration are presented in this paper. The paper suggests three design criteria. These criteria have to be considered at the early stage of the building design phase to meet the latest recommendations from the World Health Organization in most countries. The three design criteria are; first, establishing a radon barrier facing the ground; second, lowering the air pressure in the lower zone of the slab on ground facing downwards; third, diluting the indoor air with outdoor air. The first two criteria can prevent radon from infiltrating from the ground, and the third criteria can dilute the indoor air. By combining these three criteria, the indoor radon concentration can be lowered achieving an acceptable level. In addition, a cheap and reliable method for measuring the radon concentration in the indoor air is described. The provision on radon in the Danish Building Regulations complies with the latest recommendations from the World Health Organization. Radon can cause lung cancer and it is not known whether there is a lower limit for when it is not harmful to human beings. Therefore, it is important to reduce the radon concentration as much as possible in buildings. Airtightness is an important factor when dealing with buildings. It is important to avoid air leakages in the building envelope both facing the atmosphere, e.g. in compliance with energy requirements, but also facing the ground, to meet the requirements to ensure and control the indoor environment. Infiltration of air from the ground underneath a building is the main providing source of radon to the indoor air.
Abstract: Coal is an important non-renewable energy source of
and can be associated with radioactive elements. In Figueira city,
Paraná state, Brazil, it was recorded high uranium activity near the
coal mine that supplies a local thermoelectric power plant. In this
context, the radon activity (Rn-222, produced by the Ra-226 decay in
the U-238 natural series) was evaluated in groundwater, river water
and effluents produced from the acid mine drainage in the coal reject
dumps. The samples were collected in August 2013 and in February
2014 and analyzed at LABIDRO (Laboratory of Isotope and
Hydrochemistry), UNESP, Rio Claro city, Brazil, using an alpha
spectrometer (AlphaGuard) adjusted to evaluate the mean radon
activity concentration in five cycles of 10 minutes. No radon activity
concentration above 100 Bq.L-1, which was a previous critic value
established by the World Health Organization. The average radon
activity concentration in groundwater was higher than in surface
water and in effluent samples, possibly due to the accumulation of
uranium and radium in the aquifer layers that favors the radon
trapping. The lower value in the river waters can indicate dilution and
the intermediate value in the effluents may indicate radon absorption
in the coal particles of the reject dumps. The results also indicate that
the radon activities in the effluents increase with the sample
acidification, possibly due to the higher radium leaching and the
subsequent radon transport to the drainage flow. The water samples
of Laranjinha River and Ribeirão das Pedras stream, which,
respectively, supply Figueira city and receive the mining effluent,
exhibited higher pH values upstream the mine, reflecting the acid
mine drainage discharge. The radionuclides transport indicates the
importance of monitoring their activity concentration in natural
waters due to the risks that the radioactivity can represent to human
health.
Abstract: The paper deals with the analysis of hazards and sensitivity of potential resource of emergency water supply of population in a selected region of the Czech Republic. The procedure of identification and analysis of hazards and sensitivity is carried out on the basis of a unique methodology of classifying the drinking water resources earmarked for emergency supply of population. The hazard identification is based on a general register of hazards for individual parts of hydrological structure and the elements of technological equipment. It is followed by a semi-quantitative point indexation for the activation of each identified hazard, i.e. fires of anthropogenic origin, flood and the increased radioactive background accompanied by the leak of radon. Point indexation of sensitivity has been carried out at the same time. The analysis is the basis for a risk assessment of potential resource of emergency supply of population and the subsequent classification of such resource within the system of crisis planning.
Abstract: Image compression can improve the performance of
the digital systems by reducing time and cost in image storage
and transmission without significant reduction of the image quality.
Furthermore, the discrete cosine transform has emerged as the new
state-of-the art standard for image compression. In this paper, a
hybrid image compression technique based on reversible blockade
transform coding is proposed. The technique, implemented over
regions of interest (ROIs), is based on selection of the coefficients
that belong to different transforms, depending on the coefficients is
proposed. This method allows: (1) codification of multiple kernals
at various degrees of interest, (2) arbitrary shaped spectrum,and (3)
flexible adjustment of the compression quality of the image and the
background. No standard modification for JPEG2000 decoder was
required. The method was applied over different types of images.
Results show a better performance for the selected regions, when
image coding methods were employed for the whole set of images.
We believe that this method is an excellent tool for future image
compression research, mainly on images where image coding can
be of interest, such as the medical imaging modalities and several
multimedia applications. Finally VLSI implementation of proposed
method is shown. It is also shown that the kernal of Hartley and
Cosine transform gives the better performance than any other model.
Abstract: Circular knitting machine makes the fabric with more than two knitting tools. Variation of yarn tension between different knitting tools causes different loop length of stitches duration knitting process. In this research, a new intelligent method is applied to control loop length of stitches in various tools based on ideal shape of stitches and real angle of stitches direction while different loop length of stitches causes stitches deformation and deviation those of angle. To measure deviation of stitch direction against variation of tensions, image processing technique was applied to pictures of different fabrics with constant front light. After that, the rate of deformation is translated to needed compensation of loop length cam degree to cure stitches deformation. A fuzzy control algorithm was applied to loop length modification in knitting tools. The presented method was experienced for different knitted fabrics of various structures and yarns. The results show that presented method is useable for control of loop length variation between different knitting tools based on stitch deformation for various knitted fabrics with different fabric structures, densities and yarn types.
Abstract: This study aims to assess the environmental hazards
from radon exhalation rate in the soil samples in selected locations in
Iraqi Kurdistan, using passive (CR-39NTDs) and active (RAD7)
detecting method. Radon concentration, effective radium content and
radon exhalation rate were estimated in soil samples that collected at
the depth level of 30 cm inside 124 houses. The results show that the
emanation rate for radon gas was variation from location to other,
depending on the geological formation. Most health risks come from
emanation of radon and its daughter due to its contribution for indoor
radon, so the results showed that there is a linear relationship
between the ratio of soil and indoor radon concentration (CSoil Rn222/
Cindoor Rn222) and the effective radium content in soil samples. The
results show that radon concentration has high and low values in
Hajyawa city and Er. Tyrawa Qr, respectively. A comparison
between our results with that mentioned in international reports was
done.
Abstract: Earthquakes are natural phenomena that occur with influence of a lot of parameters such as seismic activity, changing in the ground waters' motion, changing in the water-s temperature, etc. On the other hand, the radon gas concentrations in soil vary as nonlinear generally with earthquakes. Continuous measurement of the soil radon gas is very important for determination of characteristic of the seismic activity. The radon gas changes as continuous with strain occurring within the Earth-s surface during an earthquake and effects from the physical and the chemical processes such as soil structure, soil permeability, soil temperature, the barometric pressure, etc. Therefore, at the modeling researches are notsufficient to knowthe concentration ofradon gas. In this research, we determined relationships between radon emissions based on the environmental parameters and earthquakes occurring along the East Anatolian Fault Zone (EAFZ), Turkiye and predicted magnitudes of some earthquakes with the artificial neural network (ANN) model.
Abstract: The measurements of 226Ra, 232Th and 40K using
gamma spectrometry and radon concentration and exhalation rates
measurements using solid state nuclear track (LR-115, Type-II
plastic) detectors are used to asses a first order exposure risk for the
persons residing in Fatehbad and Hissar districts of Western Haryana,
India. The concentration of Radium, Thorium and Potassium in the
soil samples varies from 13.37 Bq m-3 to 24.67 Bq m-3, 34.67 Bq m-3
to 67.34 Bq m-3 and 298.78 Bq m-3 to 405.67 Bq m-3 respectively
with average values of 18.78, 47.35 and 361.57 Bq m-3 respectively.
The radium equivalent activity (Raeq) calculated for the same soil
samples varies from 92.72 Bq m-3 to 140.6 Bq m-3 with an average
value of 111.80 Bq m-3. The values of absorbed dose and annual
effective dose (indoors and outdoors) are found to vary from 44.18
nGy h-1 to 65.23 nGy h-1, 0.22 mSv y-1 to 0.32 mSv y-1 and 0.05 mSv
y-1 to 0.08 mSv y-1 respectively. The radon concentration and
exhalation rates have also been reported. The radium equivalent
activities in all the soil samples were found to be lower than the limit
(370 Bq kg-1) set in the Organization for Economic Cooperation and
Development (OECD) report and the value of Hex in all the samples
is less than unity.
Abstract: Nowadays, hand vein recognition has attracted more attentions in identification biometrics systems. Generally, hand vein image is acquired with low contrast and irregular illumination. Accordingly, if you have a good preprocessing of hand vein image, we can easy extracted the feature extraction even with simple binarization. In this paper, a proposed approach is processed to improve the quality of hand vein image. First, a brief survey on existing methods of enhancement is investigated. Then a Radon Like features method is applied to preprocessing hand vein image. Finally, experiments results show that the proposed method give the better effective and reliable in improving hand vein images.
Abstract: In this work a new offline signature recognition system
based on Radon Transform, Fractal Dimension (FD) and Support Vector Machine (SVM) is presented. In the first step, projections of
original signatures along four specified directions have been performed using radon transform. Then, FDs of four obtained
vectors are calculated to construct a feature vector for each
signature. These vectors are then fed into SVM classifier for recognition of signatures. In order to evaluate the effectiveness of
the system several experiments are carried out. Offline signature
database from signature verification competition (SVC) 2004 is used
during all of the tests. Experimental result indicates that the proposed method achieved high accuracy rate in signature recognition.
Abstract: Exposure to radon occurs when breathing airborne
radon while using water: showering, washing dishes, cooking, and
drinking water that contain radon. The results of radon activity
measurements in water from public drinking fountain in city of Novi
Sad, Serbia is presented in this paper. Radon level in some samples
exceeded EPA (Environmental Protection Agency) recommendation
for maximum contaminant level (MCL) for radon in drinking water
of 11.1 Bq/l.
Abstract: The aim of the study was to investigate whether there
is the promotion of product ecodesign measures as a result of
adopting ISO 14001 certification in manufacturing companies in the
Republic of Slovenia. Companies gave the most of their product
development attention to waste and energy reduction during
manufacturing process and reduction of material consumption per
unit of product. Regarding the importance of different ecodesign
criteria reduction of material consumption per unit of product was
reported as the most important criterion. Less attention is paid to endof-
life issues considering recycling or packaging. Most
manufacturing enterprises considered ISO 14001 standard as a very
useful tool or at least a useful tool helping them to accelerate and
establish product ecodesign activities. Two most frequently
considered ecodesign drivers are increased competitive advantage
and legal requirements and two most important barriers are high
development costs and insufficient market demand.