Abstract: The exhaustion of oil and the environmental pollution from the use of fossil fuel are increasing. Tidal current power (TCP) has been proposed as an alternative energy source because of its predictability and reliability. By applying a duct and single point mooring (SPM) system, a TCP device can amplify the generating power and keep its position properly. Because the generating power is proportional to cube of the current stream velocity, amplifying the current speed by applying a duct to a TCP system is an effective way to improve the efficiency of the power device. An SPM system can be applied at any water depth and is highly cost effective. Simple installation and maintenance procedures are also merits of an SPM system. In this study, we designed an SPM system for a duct-type TCP device for use in shallow water. Motions of the duct are investigated to obtain the response amplitude operator (RAO) as the magnitude of the transfer function. Parameters affecting the stability of the SPM system such as the fairlead departure angle, current velocity, and the number of clamp weights are analyzed and/or optimized. Wadam and OrcaFlex commercial software is used to design the mooring line.
Abstract: Cavities are frequently found beneath conduits on pile
foundations in old embankments. Cavity reduces seepage length
significantly and consequently causes piping failure of embankments.
Case studies of embankment failures indicate that the relative
settlement between ground and pile supported-concrete conduit was
the main reason of the cavity. In this paper, an attempt to simulate the
cavity-induced piping failure mechanism was made using finite
element numerical method. Piping potential is examined by carrying
out parametric study for influencing factors such as cavity length,
water level, and flow conditions. The concentration of hydraulic
gradient adjacent to cavity was found. It is found that the hydraulic
gradient close to the cavity exceeds considerably the critical hydraulic
gradient causing piping. Piping failure potential due to the existence of
cavity is evaluated and contour map for the potential risk of an
embankment for piping failure is proposed.
Abstract: People’s tendency towards living in apartment houses is increasing in a densely populated country. However, some residents living in apartment houses are bothered by noise coming from the houses above. In order to reduce noise pollution, the communities are increasingly imposing a bylaw, including the limitation of floor impact sound, minimum thickness of floors, and floor soundproofing solutions. This research effort focused on the specific long-time deflection of resilient materials in the floor sound insulation systems of apartment houses. The experimental program consisted of testing nine floor sound insulation specimens subjected to sustained load for 45 days. Two main parameters were considered in the experimental investigation: three types of resilient materials and magnitudes of loads. The test results indicated that the structural behavior of the floor sound insulation systems under long-time load was quite different from that the systems under short-time load. The loading period increased the deflection of floor sound insulation systems and the increasing rate of the long-time deflection of the systems with ethylene vinyl acetate was smaller than that of the systems with low density ethylene polystyrene.
Abstract: The international society focuses on the environment
protection and natural energy sources control for the global
cooperation against weather change and sustainable growth. The study
presents the overview of the water shortage status and the necessity of wastewater reuse facility in military facilities and for the possibility of
the introduction, compares the economics by means of cost-benefit
analysis. The military features such as the number of users of military barracks and the water use were surveyed by the design principles by
facility types, the application method of wastewater reuse facility was selected, the feed water, its application and the volume of reuse volume were defined and the expectation was estimated, confirming
the possibility of introducing a wastewater reuse possibility by means of cost-benefit analysis.
Abstract: In this paper, a nonlinear acoustic echo cancellation
(AEC) system is proposed, whereby 3rd order Volterra filtering is
utilized along with a variable step-size Gauss-Seidel pseudo affine
projection (VSSGS-PAP) algorithm. In particular, the proposed
nonlinear AEC system is developed by considering a double-talk
situation with near-end signal variation. Simulation results
demonstrate that the proposed approach yields better nonlinear AEC
performance than conventional approaches.
Abstract: There are a many of needs for the development of
SiC-based hydrogen sensor for harsh environment applications. We
fabricated and investigated Pd/Ta2O5/SiC-based hydrogen sensors
with MOS capacitor structure for high temperature process monitoring
and leak detection applications in such automotive, chemical and
petroleum industries as well as direct monitoring of combustion
processes. In this work, we used silicon carbide (SiC) as a substrate to
replace silicon which operating temperatures are limited to below
200°C. Tantalum oxide was investigated as dielectric layer which has
high permeability for hydrogen gas and high dielectric permittivity,
compared with silicon dioxide or silicon nitride. Then, electrical
response properties, such as I-V curve and dependence of capacitance
on hydrogen concentrations were analyzed in the temperature ranges
of room temperature to 500°C for performance evaluation of the
sensor.
Abstract: KSLV-I(Korea Space Launch Vehicle-I) is designed as
a launch vehicle to enter a 100 kg-class satellite to the LEO(Low Earth
Orbit). Attitude angles of the upper-stage, including roll, pitch and
yaw are controlled by the cold gas thruster system using nitrogen gas.
The cold gas thruster is an actuator in the RCS(Reaction Control
System). To design an attitude controller for the upper-stage, thrust
measurement in vacuum condition is required. In this paper, the new
thrust measurement system and calibration mechanism are developed
and measurement errors and signal processing method are presented.
Abstract: An advanced composite flywheel rotor consisting of
intra and inter hybrid rims was designed to optimally increase the energy capacity, and was manufactured using filament winding with
in-situ curing. The flywheel has recently attracted considerable attention from many investigators since it possesses great potential in
many energy storage applications, including electric utilities, hybrid or
electric automobiles, and space vehicles. In this investigation, a comprehensive study was conducted with the intent to implement
composites in high performance flywheel applications.The inner two
intra-hybrid rims (rims 1 and 2) were manufactured as a whole part
through continuous filament winding under in-situ curing conditions,
and so were the outer two rims (rims 3 and 4). The outer surface of rim
2 and the inner surface of rim 3 were CNC-tapered for press-fitting. Machined rims were finally press-fitted using a hydraulic press with a
maximum compressive force of approximately 1000 ton.
Abstract: This study proposes a materials procurement contracts
model to which the zero-cost collar option is applied for heading price
fluctuation risks in construction.The material contract model based on
the collar option that consists of the call option striking zone of the
construction company(the buyer) following the materials price
increase andthe put option striking zone of the material vendor(the
supplier) following a materials price decrease. This study first
determined the call option strike price Xc of the construction company
by a simple approach: it uses the predicted profit at the project starting
point and then determines the strike price of put option Xp that has an
identical option value, which completes the zero-cost material
contract.The analysis results indicate that the cost saving of the
construction company increased as Xc decreased. This was because the
critical level of the steel materials price increasewas set at a low level.
However, as Xc decreased, Xpof a put option that had an identical
option value gradually increased. Cost saving increased as Xc
decreased. However, as Xp gradually increased, the risk of loss from a
construction company increased as the steel materials price decreased.
Meanwhile, cost saving did not occur for the construction company,
because of volatility. This result originated in the zero-cost features of
the two-way contract of the collar option. In the case of the regular
one-way option, the transaction cost had to be subtracted from the cost
saving. The transaction cost originated from an option value that
fluctuated with the volatility. That is, the cost saving of the one-way
option was affected by the volatility. Meanwhile, even though the
collar option with zero transaction cost cut the connection between
volatility and cost saving, there was a risk of exercising the put option.
Abstract: Spent petroleum catalyst from Korean petrochemical
industry contains trace amount of metals such as Ni, V and Mo.
Therefore an attempt was made to recover those trace metal using
bioleaching process. Different leaching parameters such as Fe(II)
concentration, pulp density, pH, temperature and particle size of
spent catalyst particle were studied to evaluate their effects on the
leaching efficiency. All the three metal ions like Ni, V and Mo
followed dual kinetics, i.e., initial faster followed by slower rate. The
percentage of leaching efficiency of Ni and V were higher than Mo.
The leaching process followed a diffusion controlled model and the
product layer was observed to be impervious due to formation of
ammonium jarosite (NH4)Fe3(SO4)2(OH)6. In addition, the lower
leaching efficiency of Mo was observed due to a hydrophobic coating
of elemental sulfur over Mo matrix in the spent catalyst.