Abstract: This study is concerned with pH solution detection
using 2 × 4 flexible sensor array based on a plastic polyethylene
terephthalate (PET) substrate that is coated a conductive layer and a
ruthenium dioxide (RuO2) sensitive membrane with the technologies
of screen-printing and RF sputtering. For data analysis, we also
prepared a dynamic measurement system for acquiring the response
voltage and analyzing the characteristics of the working electrodes
(WEs), such as sensitivity and linearity. In this condition, an array
measurement system was designed to acquire the original signal from
sensor array, and it is based on the method of digital signal processing
(DSP). The DSP modifies the unstable acquisition data to a direct
current (DC) output using the technique of digital filter. Hence, this
sensor array can obtain a satisfactory yield, 62.5%, through the design
measurement and analysis system in our laboratory.
Abstract: This paper presents a SCR-based ESD protection devices for I/O clamp and power rail clamp, respectably. These devices have a low trigger voltage and high holding voltage characteristics than conventional SCR device. These devices are fabricated by using 0.35um BCD (Bipolar-CMOS-DMOS) processes. These devices were validated using a TLP system. From the experimental results, the device for I/O ESD clamp has a trigger voltage of 5.8V. Also, the device for power rail ESD clamp has a holding voltage of 7.7V.
Abstract: One of the factors to maintain system survivability is
the adequate reactive power support to the system. Lack of reactive
power support may cause undesirable voltage decay leading to total
system instability. Thus, appropriate reactive power support scheme
should be arranged in order to maintain system stability. The strength
of a system capacity is normally denoted as system loadability. This
paper presents the enhancement of system loadability through
optimal reactive power planning technique using a newly developed
optimization technique, termed as Multiagent Immune Evolutionary
Programming (MAIEP). The concept of MAIEP is developed based
on the combination of Multiagent System (MAS), Artificial Immune
System (AIS) and Evolutionary Programming (EP). In realizing the
effectiveness of the proposed technique, validation is conducted on
the IEEE-26-Bus Reliability Test System. The results obtained from
pre-optimization and post-optimization process were compared
which eventually revealed the merit of MAIEP.
Abstract: This paper addresses a novel technique for placement of distributed generation (DG) in electric power systems. A GA based approach for sizing and placement of DG keeping in view of system power loss minimization in different loading conditions is explained. Minimal system power loss is obtained under voltage and line loading constraints. Proposed strategy is applied to power distribution systems and its effectiveness is verified through simulation results on 16, 37-bus and 75-bus test systems.
Abstract: In this paper Lattice Boltzmann simulation of
turbulent natural convection with large-eddy simulations (LES) in a
square cavity which is filled by water has been investigated. The
present results are validated by finds of other investigations which
have been done with different numerical methods. Calculations were
performed for high Rayleigh numbers of Ra=108 and 109. The results
confirm that this method is in acceptable agreement with other
verifications of such a flow. In this investigation is tried to present
Large-eddy turbulence flow model by Lattice Boltzmann Method
(LBM) with a clear and simple statement. Effects of increase in
Rayleigh number are displayed on streamlines, isotherm counters and
average Nusselt number. Result shows that the average Nusselt
number enhances with growth of the Rayleigh numbers.
Abstract: This paper aims to scale up Dye-sensitized Solar Cell
(DSSC) production using a commonly available industrial material –
stainless steel - and industrial plasma equipment. A working DSSC
electrode formed by (1) coating titania nanotube (TiO2 NT) film on
304 stainless steel substrate using a plasma spray technique; then, (2)
filling the nano-pores of the TiO2 NT film using a TiF4 sol-gel method.
A DSSC device consists of an anode absorbed photosensitive dye
(N3), a transparent conductive cathode with platinum (Pt)
nano-catalytic particles adhered to its surface, and an electrolytic
solution sealed between the anode and the transparent conductive
cathode. The photo-current conversion efficiency of the DSSC sample
was tested under an AM 1.5 Solar Simulator. The sample has a short
current (Isc) of 0.83 mA cm-2, open voltage (Voc) of 0.81V, filling
factor (FF) of 0.52, and conversion efficiency (η) of 2.18% on a 0.16
cm2 DSSC work-piece.
Abstract: Sign language recognition has been a topic of research since the first data glove was developed. Many researchers have attempted to recognize sign language through various techniques. However none of them have ventured into the area of Pakistan Sign Language (PSL). The Boltay Haath project aims at recognizing PSL gestures using Statistical Template Matching. The primary input device is the DataGlove5 developed by 5DT. Alternative approaches use camera-based recognition which, being sensitive to environmental changes are not always a good choice.This paper explains the use of Statistical Template Matching for gesture recognition in Boltay Haath. The system recognizes one handed alphabet signs from PSL.
Abstract: Power transformers are among the most important and
expensive equipments in the electric power systems. Consequently
the transformer protection is an essential part of the system
protection. This paper presents a new method for locating
transformer winding faults such as turn-to-turn, turn-to-core, turn-totransformer
body, turn-to-earth, and high voltage winding to low
voltage winding. In this study the current and voltage signals of input
and output terminals of the transformer are measured, which the
Fourier transform of measured signals and harmonic analysis
determine the fault's location.
Abstract: Series of experimental tests were conducted on a
section of a 660 kW wind turbine blade to measure the pressure
distribution of this model oscillating in plunging motion. In order to
minimize the amount of data required to predict aerodynamic loads
of the airfoil, a General Regression Neural Network, GRNN, was
trained using the measured experimental data. The network once
proved to be accurate enough, was used to predict the flow behavior
of the airfoil for the desired conditions.
Results showed that with using a few of the acquired data, the
trained neural network was able to predict accurate results with
minimal errors when compared with the corresponding measured
values. Therefore with employing this trained network the
aerodynamic coefficients of the plunging airfoil, are predicted
accurately at different oscillation frequencies, amplitudes, and angles
of attack; hence reducing the cost of tests while achieving acceptable
accuracy.
Abstract: This paper investigates the application of Particle Swarm Optimization (PSO) technique for coordinated design of a Power System Stabilizer (PSS) and a Thyristor Controlled Series Compensator (TCSC)-based controller to enhance the power system stability. The design problem of PSS and TCSC-based controllers is formulated as a time domain based optimization problem. PSO algorithm is employed to search for optimal controller parameters. By minimizing the time-domain based objective function, in which the deviation in the oscillatory rotor speed of the generator is involved; stability performance of the system is improved. To compare the capability of PSS and TCSC-based controller, both are designed independently first and then in a coordinated manner for individual and coordinated application. The proposed controllers are tested on a weakly connected power system. The eigenvalue analysis and non-linear simulation results are presented to show the effectiveness of the coordinated design approach over individual design. The simulation results show that the proposed controllers are effective in damping low frequency oscillations resulting from various small disturbances like change in mechanical power input and reference voltage setting.
Abstract: One of the most important power quality issues is voltage flicker. Nowadays this issue also impacts the power system all over the world. The fact of the matter is that the more and the larger capacity of wind generator has been installed. Under unstable wind power situation, the variation of output current and voltage have caused trouble to voltage flicker. Hence, the major purpose of this study is to analyze the impact of wind generator on voltage flicker of power system. First of all, digital simulation and analysis are carried out based on wind generator operating under various system short circuit capacity, impedance angle, loading, and power factor of load. The simulation results have been confirmed by field measurements.
Abstract: The paper presents a space-vector pulse width modulation (SVPWM) inverter feeding a permanent-magnet synchronous motor (PMSM). The SVPWM inverter enables to feed the motor with a higher voltage with low harmonic distortions than the conventional sinusoidal PWM inverter. The control strategy of the inverter is the voltage / frequency control method, which is based on the space-vector modulation technique. The proposed PMSM drive system involving the field-oriented control scheme not only decouples the torque and flux which provides faster response but also makes the control task easy. The performance of the proposed drive is simulated. The advantages of the proposed drive are confirmed by the simulation results.
Abstract: The switching lag-time and the voltage drop across
the power devices cause serious waveform distortions and
fundamental voltage drop in pulse width-modulated inverter output.
These phenomenons are conspicuous when both the output frequency
and voltage are low. To estimate the output voltage from the PWM
reference signal it is essential to take account of these imperfections
and to correct them. In this paper, on-line compensation method is
presented. It needs three simple blocs to add at the ideal reference
voltages. This method does not require any additional hardware
circuit and off- line experimental measurement. The paper includes
experimental results to demonstrate the validity of the proposed
method. It is applied, finally, in case of indirect vector controlled
induction machine and implemented using dSpace card.
Abstract: At present, it is very common to find renewable
energy resources, especially wind power, connected to distribution
systems. The impact of this wind power on voltage distribution levels
has been addressed in the literature. The majority of this works deals
with the determination of the maximum active and reactive power
that is possible to be connected on a system load bus, until the
voltage at that bus reaches the voltage collapse point. It is done by the
traditional methods of PV curves reported in many references.
Theoretical expression of maximum power limited by voltage
stability transfer through a grid is formulated using an exact
representation of distribution line with ABCD parameters. The
expression is used to plot PV curves at various power factors of a
radial system. Limited values of reactive power can be obtained. This
paper presents a method to study the relationship between the active
power and voltage (PV) at the load bus to identify the voltage
stability limit. It is a foundation to build a permitted working
operation region in complying with the voltage stability limit at the
point of common coupling (PCC) connected wind farm.
Abstract: This paper presents the effectiveness of artificial
intelligent technique to apply for pattern recognition and
classification of Partial Discharge (PD). Characteristics of PD signal
for pattern recognition and classification are computed from the
relation of the voltage phase angle, the discharge magnitude and the
repeated existing of partial discharges by using statistical and fractal
methods. The simplified fuzzy ARTMAP (SFAM) is used for pattern
recognition and classification as artificial intelligent technique. PDs
quantities, 13 parameters from statistical method and fractal method
results, are inputted to Simplified Fuzzy ARTMAP to train system
for pattern recognition and classification. The results confirm the
effectiveness of purpose technique.
Abstract: This paper deals with the effect of a power transformer’s vector group on the basic voltage sag characteristics during unbalanced faults at a meshed or radial power network. Specifically, the propagation of voltage sags through a power transformer is studied with advanced short-circuit analysis. A smart method to incorporate this effect on analytical mathematical expressions is proposed. Based on this methodology, the positive effect of transformers of certain vector groups on the mitigation of the expected number of voltage sags per year (sag frequency) at the terminals of critical industrial customers can be estimated.
Abstract: Photo-BJMOSFET (Bipolar Junction Metal-Oxide-
Semiconductor Field Effect Transistor) fabricated on SOI film was proposed. ITO film is adopted in the device as gate electrode to reduce
light absorption. Depletion region but not inversion region is formed
in film by applying gate voltage (but low reverse voltage) to achieve
high photo-to-dark-current ratio. Comparisons of photoelectriccharacteristics
executed among VGK=0V, 0.3V, 0.6V, 0.9V and 1.0V
(reverse voltage VAK is equal to 1.0V for total area of 10×10μm2). The
results indicate that the greatest improvement in photo-to-dark-current
ratio is achieved up to 2.38 at VGK=0.6V. In addition,
photo-BJMOSFET is compatible with CMOS integration due to big
input resistance
Abstract: The hard clam (meretrix lusoria) cultivated industry
has been developed vigorously for recent years in Taiwan, and
seawater quality determines the cultivated environment. The pH
concentration variation affects survival rate of meretrix lusoria
immediately. In order to monitor seawater quality, solid-state sensing
electrode of ruthenium-doped titanium dioxide (TiO2:Ru) is developed
to measure hydrogen ion concentration in different cultivated
solutions. Because the TiO2:Ru sensing electrode has high chemical
stability and superior sensing characteristics, thus it is applied as a pH
sensor. Response voltages of TiO2:Ru sensing electrode are readout by
instrument amplifier in different sample solutions. Mean sensitivity
and linearity of TiO2:Ru sensing electrode are 55.20 mV/pH and 0.999
from pH1 to pH13, respectively. We expect that the TiO2:Ru sensing
electrode can be applied to real environment measurement, therefore
we collect two sample solutions by different meretrix lusoria
cultivated ponds in the Yunlin, Taiwan. The two sample solutions are
both measured for 200 seconds after calibration of standard pH buffer
solutions (pH7, pH8 and pH 9). Mean response voltages of sample 1
and sample 2 are -178.758 mV (Standard deviation=0.427 mV) and
-180.206 mV (Standard deviation =0.399 mV), respectively. Response
voltages of the two sample solutions are between pH 8 and pH 9 which
conform to weak alkali range and suitable meretrix lusoria growth. For
long-term monitoring, drift of cultivated solutions (sample 1 and
sample 2) are 1.16 mV/hour and 1.03 mV/hour, respectively.
Abstract: Customer-supplier collaboration enables firms to
achieve greater success than acting independently. Nevertheless, not
many firms have fully utilized the potential of collaboration. This
paper presents organizational and human related success factors for
collaboration in manufacturing supply chains in casting industry. Our
research approach was a case study including multiple cases. Data
was gathered by interviews and group discussions in two different
research projects. In the first research project we studied seven firms
and in the second five. It was found that the success factors are
interrelated, in other words, organizational and human factors
together enable success but not any of them alone. Some of the found
success factors are a culture of following agreements, and a speed of
informing the partner about changes affecting to the product or the
delivery chain.
Abstract: Using strength Pulse Electrical Field (PEF) in food
industries is a non-thermal process that can deactivate
microorganisms and increase penetration in plant and animals tissues
without serious impact on food taste and quality. In this paper designing and fabricating of a PEF generator has been presented. Pulse generation methods have been surveyed and the best of them
selected. The equipment by controller set can generate square pulse with adjustable parameters such as amplitude 1-5kV, frequency 0.1-10Hz, pulse width 10-100s, and duty cycle 0-100%. Setting the number of pulses, and presenting the output voltage and current
waveforms on the oscilloscope screen are another advantages of this
equipment. Finally, some food samples were tested that yielded the satisfactory results. PEF applying had considerable effects on potato, banana and purple cabbage. It caused increase Brix factor from 0.05
to 0.15 in potato solution. It is also so effective in extraction color material from purple cabbage. In the last experiment effects of PEF
voltages on color extraction of saffron scum were surveyed (about 6% increasing yield).