Abstract: In deregulated operating regime power system security is an issue that needs due thoughtfulness from researchers in the horizon of unbundling of generation and transmission. Electric power systems are exposed to various contingencies. Network contingencies often contribute to overloading of branches, violation of voltages and also leading to problems of security/stability. To maintain the security of the systems, it is desirable to estimate the effect of contingencies and pertinent control measurement can be taken on to improve the system security. This paper presents the application of particle swarm optimization algorithm to find the optimal location of multi type FACTS devices in a power system in order to eliminate or alleviate the line over loads. The optimizations are performed on the parameters, namely the location of the devices, their types, their settings and installation cost of FACTS devices for single and multiple contingencies. TCSC, SVC and UPFC are considered and modeled for steady state analysis. The selection of UPFC and TCSC suitable location uses the criteria on the basis of improved system security. The effectiveness of the proposed method is tested for IEEE 6 bus and IEEE 30 bus test systems.
Abstract: This paper presents the voltage regulation scheme of
D-STATCOM under three-phase faults. It consists of the voltage
detection and voltage regulation schemes in the 0dq reference. The
proposed control strategy uses the proportional controller in which
the proportional gain, kp, is appropriately adjusted by using genetic
algorithms. To verify its use, a simplified 4-bus test system is situated
by assuming a three-phase fault at bus 4. As a result, the DSTATCOM
can resume the load voltage to the desired level within
1.8 ms. This confirms that the proposed voltage regulation scheme
performs well under three-phase fault events.
Abstract: This study aims to assess the potential of solar energy technology for improving access to water and hence the livelihood strategies of rural communities in Baja California Sur, Mexico. It focuses on livestock ranches and photovoltaic water-pumptechnology as well as other water extraction methods. The methodology used are the Sustainable Livelihoods and the Appropriate Technology approaches. A household survey was applied in June of 2006 to 32 ranches in the municipality, of which 22 used PV pumps; and semi-structured interviews were conducted. Findings indicate that solar pumps have in fact helped people improve their quality of life by allowing them to pursue a different livelihood strategy and that improved access to water -not necessarily as more water but as less effort to extract and collect it- does not automatically imply overexploitation of the resource; consumption is based on basic needs as well as on storage and pumping capacity. Justification for such systems lies in the avoidance of logistical problems associated to fossil fuels, PV pumps proved to be the most beneficial when substituting gasoline or diesel equipment but of dubious advantage if intended to replace wind or gravity systems. Solar water pumping technology-s main obstacle to dissemination are high investment and repairs costs and it is therefore not suitable for all cases even when insolation rates and water availability are adequate. In cases where affordability is not an obstacle it has become an important asset that contributes –by means of reduced expenses, less effort and saved time- to the improvement of livestock, the main livelihood provider for these ranches.
Abstract: In this paper two different Antilock braking system (ABS) are simulated and compared. One is the ordinary hydraulic ABS system which we call it ABS and the other is Electromagnetic Antilock braking system which is called (EMABS) the basis of performance of an EMABS is based upon Electromagnetic force. In this system there is no need to use servo hydraulic booster which are used in ABS system. In EMABS to generate the desired force we have use a magnetic relay which works with an input voltage through an air gap (g). The generated force will be amplified by the relay arm, and is applied to the brake shoes and thus the braking torque is generated. The braking torque is proportional to the applied electrical voltage E. to adjust the braking torque it is only necessary to regulate the electrical voltage E which is very faster and has a much smaller time constant T than the ABS system. The simulations of these two different ABS systems are done with MATLAB/SIMULINK software and the superiority of the EMABS has been shown.
Abstract: In this study we present the effect of elevated
temperatures from 300K to 400K on the electrical properties of
copper Phthalocyanine (CuPc) based organic field effect transistors
(OFET). Thin films of organic semiconductor CuPc (40nm) and
semitransparent Al (20nm) were deposited in sequence, by vacuum
evaporation on a glass substrate with previously deposited Ag source
and drain electrodes with a gap of 40 μm. Under resistive mode of
operation, where gate was suspended it was observed that drain
current of this organic field effect transistor (OFET) show an
increase with temperature. While in grounded gate condition metal
(aluminum) – semiconductor (Copper Phthalocyanine) Schottky
junction dominated the output characteristics and device showed
switching effect from low to high conduction states like Zener diode
at higher bias voltages. This threshold voltage for switching effect
has been found to be inversely proportional to temperature and shows
an abrupt decrease after knee temperature of 360K. Change in
dynamic resistance (Rd = dV/dI) with respect to temperature was
observed to be -1%/K.
Abstract: A novel application of neural network approach to
fault classification and fault location of Medium voltage cables is
demonstrated in this paper. Different faults on a protected cable
should be classified and located correctly. This paper presents the use
of neural networks as a pattern classifier algorithm to perform these
tasks. The proposed scheme is insensitive to variation of different
parameters such as fault type, fault resistance, and fault inception
angle. Studies show that the proposed technique is able to offer high
accuracy in both of the fault classification and fault location tasks.
Abstract: Rotor Flux based Model Reference Adaptive System
(RF-MRAS) is the most popularly used conventional speed
estimation scheme for sensor-less IM drives. In this scheme, the
voltage model equations are used for the reference model. This
encounters major drawbacks at low frequencies/speed which leads to
the poor performance of RF-MRAS. Replacing the reference model
using Neural Network (NN) based flux estimator provides an
alternate solution and addresses such drawbacks. This paper
identifies an NN based flux estimator using Single Neuron Cascaded
(SNC) Architecture. The proposed SNC-NN model replaces the
conventional voltage model in RF-MRAS to form a novel MRAS
scheme named as SNC-NN-MRAS. Through simulation the proposed
SNC-NN-MRAS is shown to be promising in terms of all major
issues and robustness to parameter variation. The suitability of the
proposed SNC-NN-MRAS based speed estimator and its advantages
over RF-MRAS for sensor-less induction motor drives is
comprehensively presented through extensive simulations.
Abstract: This work is devoted to the calculation of the
undulatory parameters and the study of the influence of te number
parallel path of a winding on overvoltage compared to the frame and
between turns (sections) in a multiturn random winding of an
asynchronous motors supplied with PWM- converters.
Abstract: Power line channel is proposed as an alternative for broadband data transmission especially in developing countries like Tanzania [1]. However the channel is affected by stochastic attenuation and deep notches which can lead to the limitation of channel capacity and achievable data rate. Various studies have characterized the channel without giving exactly the maximum performance and limitation in data transfer rate may be this is due to complexity of channel modeling being used. In this paper the channel performance of medium voltage, low voltage and indoor power line channel is presented. In the investigations orthogonal frequency division multiplexing (OFDM) with phase shift keying (PSK) as carrier modulation schemes is considered, for indoor, medium and low voltage channels with typical ten branches and also Golay coding is applied for medium voltage channel. From channels, frequency response deep notches are observed in various frequencies which can lead to reduce the achievable data rate. However, is observed that data rate up to 240Mbps is realized for a signal to noise ratio of about 50dB for indoor and low voltage channels, however for medium voltage a typical link with ten branches is affected by strong multipath and coding is required for feasible broadband data transfer.
Abstract: In this paper effects of inclination angle on natural
convection flow in an open cavity has been analyzed with Lattice
Boltzmann Method (LBM).The angle of inclination varied from θ= -
45° to 45° with 15° intervals. Study has been conducted for Rayleigh
numbers (Ra) 104 to 106. The comparisons show that the average
Nusselt number increases with growth of Rayleigh number and the
average Nusselt number increase as inclination angles increases at
Ra=104.At Ra=105 and Ra=106 the average Nusselt number enhance
as inclination angels varied from θ= -45° to θ= 0° and decrease as
inclination angels increase in θ= 0° to θ= 45°.
Abstract: A high-linearity and high-speed current-mode sampleand-
hold circuit is designed and simulated using a 0.25μm CMOS
technology. This circuit design is based on low voltage and it utilizes
a fully differential circuit. Due to the use of only two switches the
switch related noise has been reduced. Signal - dependent -error is
completely eliminated by a new zero voltage switching technique.
The circuit has a linearity error equal to ±0.05μa, i.e. 12-bit
accuracy with a ±160 μa differential output - input signal frequency
of 5MHZ, and sampling frequency of 100 MHZ. Third
harmonic is equal to –78dB.
Abstract: A new design approach for three-stage operational
amplifiers (op-amps) is proposed. It allows to actually implement a
symmetrical push-pull class-AB amplifier output stage for wellestablished
three-stage amplifiers using a feedforward
transconductance stage. Compared with the conventional design
practice, the proposed approach leads to a significant
improvement of the symmetry between the positive and the
negative op-amp step response, resulting in similar values of the
positive/negative settling time. The new approach proves to be very
useful in order to fully exploit the potentiality allowed by the op-amp
in terms of speed performances. Design examples in a commercial
0.35-μm CMOS prove the effectiveness of theproposed strategy.
Abstract: Hybrid photovoltaic thermal (PV/T) solar system comprises a solar collector which is disposed on photovoltaic solar cells. The disadvantage of a conventional photovoltaic cell is that its performance decreases as the temperature increases. Indeed, part of the solar radiation is converted into electricity and is dissipated as heat, increasing the temperature of the photovoltaic cell with respect to the ambient temperature. The objective of this work is to study experimentally and implement a hybrid prototype to evaluate electrical and thermal performance. In this paper, an experimental study of two new configurations of hybrid collectors is exposed. The results are given and interpreted. The two configurations of absorber studied are a new combination with tubes and galvanized tank, the other is a tubes and sheet.
Abstract: Two geometrically nonlinear plate theories, based either on first- or third-order transverse shear deformation theory are used for finite element modeling and simulation of the transient response of smart structures incorporating piezoelectric layers. In particular the time histories of nonlinear vibrations and sensor voltage output of a thin beam with a piezoelectric patch bonded to the surface due to an applied step force are studied.
Abstract: In this treatise we will study the capability of static
compensator for reactive power to stabilize sheen voltage with motor
loading on power networks system. We also explain the structure and main function of STATCOM and the method to control it using STATCOM transformer current to simultaneously predict after
telling about the necessity of FACTS tools to compensate in power networks. Then we study topology and controlling system to stabilize
voltage during start of inductive motor. The outcome of stimulat by MATLAB software supports presented controlling idea and
system in the treatise.
Abstract: Charge Simulation Method (CSM) is one of the very widely used numerical field computation technique in High Voltage (HV) engineering. The high voltage fields of varying non uniformities are encountered in practice. CSM programs being case specific, the simulation accuracies heavily depend on the user (programmers) experience. Here is an effort to understand CSM errors and evolve some guidelines to setup accurate CSM models, relating non uniformities with assignment factors. The results are for the six-point-charge model of sphere-plane gap geometry. Using genetic algorithm (GA) as tool, optimum assignment factors at different non uniformity factors for this model have been evaluated and analyzed. It is shown that the symmetrically placed six-point-charge models can be good enough to set up CSM programs with potential errors less than 0.1% when the field non uniformity factor is greater than 2.64 (field utilization factor less than 52.76%).
Abstract: This paper presents a simple method for estimation of
additional load as a factor of the existing load that may be drawn
before reaching the point of line maximum loadability of radial
distribution system (RDS) with different realistic load models at
different substation voltages. The proposed method involves a simple
line loadability index (LLI) that gives a measure of the proximity of
the present state of a line in the distribution system. The LLI can use
to assess voltage instability and the line loading margin. The
proposed method also compares with the existing method of
maximum loadability index [10]. The simulation results show that the
LLI can identify not only the weakest line/branch causing system
instability but also the system voltage collapse point when it is near
one. This feature enables us to set an index threshold to monitor and
predict system stability on-line so that a proper action can be taken to
prevent the system from collapse. To demonstrate the validity of the
proposed algorithm, computer simulations are carried out on two bus
and 69 bus RDS.
Abstract: This paper presents design, analysis and comparison of the different rotor type permanent magnet machines. The presented machines are designed as having same geometrical dimensions and same materials for comparison. The main machine parameters of interior and exterior rotor type machines including eddy current effect, torque-speed characteristics and magnetic analysis are investigated using MAXWELL program. With this program, the components of the permanent magnet machines can be calculated with high accuracy. Six types of Permanent machines are compared with respect to their topology, size, magnetic field, air gap flux, voltage, torque, loss and efficiency. The analysis results demonstrate the effectiveness of the proposed machines design methodology. We believe that, this study will be a helpful resource in terms of examination and comparison of the basic structure and magnetic features of the PM (Permanent magnet) machines which have different rotor structure.
Abstract: Deep Brain Stimulation or DBS is a surgical treatment for Parkinson-s Disease with three stimulation parameters: frequency, pulse width, and voltage. The parameters should be selected appropriately to achieve effective treatment. This selection now, performs clinically. The aim of this research is to study chaotic behavior of recorded tremor of patients under DBS in order to present a computational method to recognize stimulation optimum voltage. We obtained some chaotic features of tremor signal, and discovered embedding space of it has an attractor, and its largest Lyapunov exponent is positive, which show tremor signal has chaotic behavior, also we found out, in optimal voltage, entropy and embedding space variance of tremor signal have minimum values in comparison with other voltages. These differences can help neurologists recognize optimal voltage numerically, which leads to reduce patients' role and discomfort in optimizing stimulation parameters and to do treatment with high accuracy.
Abstract: This paper presents an efficient approach to feeder
reconfiguration for power loss reduction and voltage profile
imprvement in unbalanced radial distribution systems (URDS). In
this paper Genetic Algorithm (GA) is used to obtain solution for
reconfiguration of radial distribution systems to minimize the losses.
A forward and backward algorithm is used to calculate load flows in
unbalanced distribution systems. By simulating the survival of the
fittest among the strings, the optimum string is searched by
randomized information exchange between strings by performing
crossover and mutation. Results have shown that proposed algorithm
has advantages over previous algorithms The proposed method is
effectively tested on 19 node and 25 node unbalanced radial
distribution systems.