Abstract: This paper presents effects of the mean operating
pressure on the optimal operating frequency based on temperature
differences across stack ends in a thermoacoustic refrigerator. In
addition to the length of the resonance tube, components of the
thermoacoustic refrigerator have an influence on the operating
frequency due to their acoustic properties, i.e., absorptivity,
reflectivity and transmissivity. The interference of waves incurs and
distorts the original frequency generated by the driver so that the
optimal operating frequency differs from the designs. These acoustic
properties are not parameters in the designs and be very complicated
to infer their responses. A prototype thermoacoustic refrigerator is
constructed and used to investigate its optimal operating frequency
compared to the design at various operating pressures. Helium and air
are used as working fluids during the experiments. The results
indicate that the optimal operating frequency of the prototype
thermoacoustic refrigerator using helium is at 6 bar and 490Hz or
approximately 20% away from the design frequency. The optimal
operating frequency at other mean pressures differs from the design
in an unpredictable manner, however, the optimal operating
frequency and pressure can be identified by testing.
Abstract: Honeys are produced by Apis mellifera and stingless
bees (Meliponini) in Ecuador. We studied honey produced in
beeswax combs by Apis mellifera, and honey produced in pots by
Geotrigona and Scaptotrigona bees. Chloroform extracts of honey
were obtained for fast NMR spectra. The 1D spectra were acquired at
298 K, with a 600 MHz NMR Bruker instrument, using a modified
double pulsed field gradient spin echoes (DPFGSE) sequence.
Signals of 1H NMR spectra were integrated and used as inputs for
PCA, PLS-DA analysis, and labelled sets of classes were successfully
identified, enhancing the separation between the three groups of
honey according to the entomological origin: A. mellifera,
Geotrigona and Scaptotrigona. This procedure is therefore
recommended for authenticity test of honey in Ecuador.
Abstract: This paper deals with the theoretical and numerical
investigation of magneto hydrodynamic boundary layer flow of a
nanofluid past a wedge shaped wick in heat pipe used for the cooling
of electronic components and different type of machines. To
incorporate the effect of nanoparticle diameter, concentration of
nanoparticles in the pure fluid, nanothermal layer formed around the
nanoparticle and Brownian motion of nanoparticles etc., appropriate
models are used for the effective thermal and physical properties of
nanofluids. To model the rotation of nanoparticles inside the base
fluid, microfluidics theory is used. In this investigation ethylene
glycol (EG) based nanofluids, are taken into account. The non-linear
equations governing the flow and heat transfer are solved by using a
very effective particle swarm optimization technique along with
Runge-Kutta method. The values of heat transfer coefficient are
found for different parameters involved in the formulation viz.
nanoparticle concentration, nanoparticle size, magnetic field and
wedge angle etc. It is found that, the wedge angle, presence of
magnetic field, nanoparticle size and nanoparticle concentration etc.
have prominent effects on fluid flow and heat transfer characteristics
for the considered configuration.
Abstract: In emerging economies, recycling is an opportunity
for the cities to increase the lifespan of sanitary landfills, reduce the
costs of the solid waste management, decrease the environmental
problems of the waste treatment through reincorporate waste in the
productive cycle and protect and develop people’s livelihoods of
informal waste pickers. However, few studies have analysed the
possibilities and strategies to integrate formal and informal sectors in
the solid waste management for the benefit of both. This study seek
to make a strength, weakness, opportunity, and threat (SWOT)
analysis in three recycling associations of Bogotá with the aim to
understand and determine the situation of recycling from perspective
of informal sector in its transition to enter as authorized waste
providers. Data used in the analysis are derived from multiple
strategies such as literature review, the Bogota’s recycling database,
focus group meetings, governmental reports, national laws and
regulations and specific interviews with key stakeholders. Results of
this study show as the main stakeholders of formal and informal
sector of waste management can identify the internal and internal
conditions of recycling in Bogotá. Several strategies were designed
based on the SWOTs determined, could be useful for Bogotá to
advance and promote recycling as a key strategy for integrated
sustainable waste management in the city.
Abstract: Scrubbing by a liquid spraying is one of the most
effective processes used for removal of fine particles and soluble
gas pollutants (such as SO2, HCl, HF) from the flue gas. There are
many configurations of scrubbers designed to provide contact
between the liquid and gas stream for effectively capturing
particles or soluble gas pollutants, such as spray plates, packed bed
towers, jet scrubbers, cyclones, vortex and venturi scrubbers. The
primary function of venturi scrubber is the capture of fine particles
as well as HCl, HF or SO2 removal with effect of the flue gas
temperature decrease before input to the absorption column. In this
paper, sulfur dioxide (SO2) from flue gas was captured using new
design replacing venturi scrubber (1st degree of wet scrubbing).
The flue gas was prepared by the combustion of the carbon
disulfide solution in toluene (1:1 vol.) in the flame in the reactor.
Such prepared flue gas with temperature around 150°C was
processed in designed laboratory O-element scrubber. Water was
used as absorbent liquid. The efficiency of SO2 removal, pressure
drop and temperature drop were measured on our experimental
device. The dependence of these variables on liquid-gas ratio was
observed. The average temperature drop was in the range from
150°C to 40°C. The pressure drop was increased with increasing of
a liquid-gas ratio, but no too much as for the common venturi
scrubber designs. The efficiency of SO2 removal was up to 70 %.
The pressure drop of our new designed wet scrubber is similar to
commonly used venturi scrubbers; nevertheless the influence of
amount of the liquid on pressure drop is not so significant.
Abstract: This paper is concerned with knowledge representation
and extraction of fuzzy if-then rules using Interval Type-2
Context-based Fuzzy C-Means clustering (IT2-CFCM) with the aid of
fuzzy granulation. This proposed clustering algorithm is based on
information granulation in the form of IT2 based Fuzzy C-Means
(IT2-FCM) clustering and estimates the cluster centers by preserving
the homogeneity between the clustered patterns from the IT2 contexts
produced in the output space. Furthermore, we can obtain the
automatic knowledge representation in the design of Radial Basis
Function Networks (RBFN), Linguistic Model (LM), and Adaptive
Neuro-Fuzzy Networks (ANFN) from the numerical input-output data
pairs. We shall focus on a design of ANFN in this paper. The
experimental results on an estimation problem of energy performance
reveal that the proposed method showed a good knowledge
representation and performance in comparison with the previous
works.
Abstract: We have conducted the optimal synthesis of rootmean-
squared objective filter to estimate the state vector in the case if
within the observation channel with memory the anomalous noises
with unknown mathematical expectation are complement in the
function of the regular noises. The synthesis has been carried out for
linear stochastic systems of continuous - time.
Abstract: We investigate relaxation dynamics of a quantum
dipole emitter (QDE), e.g., a molecule or quantum dot, located near a
metal nanoparticle (MNP) exhibiting a dipolar localized surface
plasmon (LSP) resonance at the frequency of the QDE radiative
transition. It is shown that under the condition of the QDE-MNP
characteristic relaxation time being much shorter than that of the
QDE in free-space but much longer than the LSP lifetime. It is also
shown that energy dissipation in the QDE-MNP system is relatively
weak with the probability of the photon emission being about 0.75, a
number which, rather surprisingly, does not explicitly depend on the
metal absorption characteristics. The degree of entanglement
measured by the concurrency takes the maximum value, while the
distances between the QDEs and metal ball approximately are equal.
Abstract: Propylene self-metathesis to ethylene and butene was
studied over WOx/SiO2 catalysts at 450oC and atmospheric pressure.
The WOx/SiO2 catalysts were prepared by incipient wetness
impregnation of ammonium metatungstate aqueous solution. It was
found that, adding nano-sized extra supports (SiO2 and TiO2) by
physical mixing with the WOx/SiO2 enhanced propylene conversion.
The UV-Vis and FT-Raman results revealed that WOx could migrate
from the original silica support to the extra support, leading to a
better dispersion of WOx. The ICP-OES results also indicate that
WOx existed on the extra support. Coke formation was investigated
on the catalysts after 10 h time-on-stream by TPO. However, adding
nano-sized extra supports led to higher coke formation which may be
related to acidity as characterized by NH3-TPD.
Abstract: This paper presents the design and fabrication of an
optical window for an optical modulator toward image sensing
applications. An optical window consists of micrometer-order SiO2
capillaries (porous solid) that can modulate transmission light
intensity by moving the liquid in and out of porous solid. A high
optical transmittance of the optical window can be achieved due to
refractive index matching when the liquid is penetrated into the
porous solid. Otherwise, its light transmittance is lower because of
light reflection and scattering by air holes and capillary walls. Silicon
capillaries fabricated by deep reactive ion etching (DRIE) process are
completely oxidized to form the SiO2 capillaries. Therefore, high
aspect ratio SiO2 capillaries can be achieved based on silicon
capillaries formed by DRIE technique. Large compressive stress of
the oxide causes bending of the capillary structure, which is reduced
by optimizing the design of device structure. The large stress of the
optical window can be released via thin supporting beams. A 7.2 mm
x 9.6 mm optical window area toward a fully integrated with the
image sensor format is successfully fabricated and its optical
transmittance is evaluated with and without inserting liquids (ethanol
and matching oil). The achieved modulation range is approximately
20% to 35% with and without liquid penetration in visible region
(wavelength range from 450 nm to 650 nm).
Abstract: A cyclostationary Gaussian linearization method is
formulated for investigating the time average response of nonlinear
system under sinusoidal signal and white noise excitation. The
quantitative measure of cyclostationary mean, variance, spectrum of
mean amplitude, and mean power spectral density of noise are
analyzed. The qualitative response behavior of stochastic jump and
bifurcation are investigated. The validity of the present approach in
predicting the quantitative and qualitative statistical responses is
supported by utilizing Monte Carlo simulations. The present analysis
without imposing restrictive analytical conditions can be directly
derived by solving non-linear algebraic equations. The analytical
solution gives reliable quantitative and qualitative prediction of mean
and noise response for the Duffing system subjected to both sinusoidal
signal and white noise excitation.
Abstract: This paper presents a model for a modified T-junction
device for microspheres generation. The numerical model is
developed using a commercial software package: COMSOL
Multiphysics. In order to test the accuracy of the numerical model,
multiple variables, such as the flow rate of cross-flow, fluid properties,
structure, and geometry of the microdevice are applied. The results
from the model are compared with the experimental results in the
diameter of the microsphere generated. The comparison shows a good
agreement. Therefore the model is useful in further optimization of the
device and feedback control of microsphere generation if any.
Abstract: Although, lanthanum carbonate has not been approved
by the FDA for treatment of hyperphosphatemia, we prospectively
evaluated the efficacy of the combination of Calcium hydroxyapatite
(CHAp) and Lanthanum Carbonate (LaC) for the treatment of
hyperphosphatemia on mice. CHAp was prepared by co-precipitation
method using Ca(OH)2, H3PO4, NH4OH with calcination at 1200ºC.
Lanthanum carbonate was prepared by chemical method using
NaHCO3 and LaCl3 at low pH environment, below 4.0. The
structures were characterized by FTIR spectra and SEM -EDX
analysis. The study group included 16 subjects-mice divided into four
groups according to the administered substance: lanthanum carbonate
(group A), CHAp (group B), lanthanum carbonate + CHAp (group C)
and salt water (group D). The results indicate a phosphate decrease
when subjects (mice) were treated with CHAp and lanthanum
carbonate (0.5% CMC), in a single dose of 1500 mg/kg. Serum
phosphate concentration decreased [(from 4.5 ± 0.8 mg/dL) to
4.05 ± 0.2 mg/dL), P < 0.01] in group A and in group C (to 3.6
± 0.2 mg/dL) at 12 hours from the administration. The combination
of CHAp and lanthanum carbonate is a suitable regimen for
hyperphosphatemia treatment because it avoids both the
hypercalcemia of CaCO3 and the adverse effects of CHAp.
Abstract: This study investigates the suitability of using plastic,
such as polyethylene terephthalate (PET), as a partial replacement of
natural coarse and fine aggregates (for example, brick chips and
natural sand) to produce lightweight concrete for load bearing
structural members. The plastic coarse aggregate (PCA) and plastic
fine aggregate (PFA) were produced from melted polyethylene
terephthalate (PET) bottles. Tests were conducted using three
different water–cement (w/c) ratios, such as 0.42, 0.48, and 0.57,
where PCA and PFA were used as 50% replacement of coarse and
fine aggregate respectively. Fresh and hardened properties of
concrete have been compared for natural aggregate concrete (NAC),
PCA concrete (PCC) and PFA concrete (PFC). The compressive
strength of concrete at 28 days varied with the water–cement ratio for
both the PCC and PFC. Between PCC and PFC, PFA concrete
showed the highest compressive strength (23.7 MPa) at 0.42 w/c ratio
and also the lowest compressive strength (13.7 MPa) at 0.57 w/c
ratio. Significant reduction in concrete density was mostly observed
for PCC samples, ranging between 1977–1924 kg/m³. With the
increase in water–cement ratio PCC achieved higher workability
compare to both NAC and PFC. It was found that both the PCA and
PFA contained concrete achieved the required compressive strength
to be used for structural purpose as partial replacement of the natural
aggregate; but to obtain the desired lower density as lightweight
concrete the PCA is most suited.
Abstract: The quality and condition of perishable products
delivered to the market and their subsequent selling prices are
directly affected by the care taken during harvesting and handling.
Mechanical injury, in fact, occurs at all stages, from pre-harvest
operations through post-harvest handling, packing and transport to
the market. The main implications of this damage are the reduction of
the product’s quality and economical losses related to the shelf life
diminution. For most perishable products, the shelf life is relatively
short and it is typically dictated by microbial growth related to the
application of dynamic and static loads during transportation. This
paper presents the correlation between vibration levels and
microbiological growth on strawberries and woodland strawberries
and detects the presence of volatile organic compounds (VOC) in
order to develop an intelligent logistic unit capable of monitoring
VOCs using a specific sensor system. Fresh fruits were exposed to
vibrations by means of a vibrating table in a temperature-controlled
environment. Microbiological analyses were conducted on samples,
taken at different positions along the column of the crates. The values
obtained were compared with control samples not exposed to
vibrations and the results show that different positions along the
column influence the development of bacteria, yeasts and filamentous
fungi.
Abstract: Alone with fast urbanization in world, traffic control
became a big issue in urban construction. Having an efficient and
reliable traffic control system is crucial to macro-traffic control.
Traffic signal is used to manage conflicting requirement by allocating
different sets of mutually compatible traffic movement during distinct
time interval. Many approaches have been made proposed to solve
this discrete stochastic problem. Recognizing the need to minimize
right-of-way impacts while efficiently handling the anticipated high
traffic volumes, the proposed alternative system gives effective
design. This model allows for increased traffic capacity and reduces
delays by eliminating a step in maneuvering through the freeway
interchange. The concept proposed in this paper involves
construction of bridges and ramps at intersection of four roads to
control the vehicular congestion and to prevent traffic breakdown.
Abstract: Microalgae Meyerella planktonica is a potential
biofuel source because it can grow in bulk in either autotrophic or
heterotrophic condition. However, the quantitative growth of this
algal type is still low as it tends to precipitates on the bottom.
Besides, the lipid concentration is still low when grown in
autotrophic condition. In contrast, heterotrophic condition can
enhance the lipid concentration. The combination of autotrophic
condition and agitation treatment was conducted to increase the
density of the culture. On the other hand, a heterotrophic condition
was set up to raise the lipid production. A two-stage experiment
was applied to increase the density at the first step and to increase
the lipid concentration in the next step. The autotrophic condition
resulted higher density but lower lipid concentration compared to
heterotrophic one. The agitation treatment produced higher density
in both autotrophic and heterotrophic conditions. The two-stage
experiment managed to enhance the density during the autotrophic
stage and the lipid concentration during the heterotrophic stage.
The highest yield was performed by using 0.4% v/v glycerol as a
carbon source (2.9±0.016 x 10^6 cells w/w) attained 7 days after the
heterotrophic stage began. The lipid concentration was stable
starting from day 7.
Abstract: In this article, the antibiogram and heavy metal
resistance profile of the bacteria isolated from total 34 studied
animals (Pelophylax ridibundus = 12; Mauremys rivulata = 14;
Natrix natrix = 8) captured around the Biga Stream, are described.
There was no database information on antibiogram and heavy metal
resistance profile of bacteria from these area’s amphibians and
reptiles.
A total of 200 bacteria were successfully isolated from cloaca and
oral samples of the aquatic amphibians and reptiles as well as from
the water sample. According to Jaccard’s similarity index, the degree
of similarity in the bacterial flora was quite high among the
amphibian and reptile species under examination, whereas it was
different from the bacterial diversity in the water sample. The most
frequent isolates were A. hydrophila (31.5%), B. pseudomallei
(8.5%), and C. freundii (7%). The total numbers of bacteria obtained
were as follows: 45 in P. ridibundus, 45 in N. natrix 30 in M.
rivulata, and 80 in the water sample. The result showed that
cefmetazole was the most effective antibiotic to control the bacteria
isolated in this study and that approximately 93.33% of the bacterial
isolates were sensitive to this antibiotic. The multiple antibiotic
resistances (MAR) index indicated that P. ridibundus (0.95) > N.
natrix (0.89) > M. rivulata (0.39). Furthermore, all the tested heavy
metals (Pb+2, Cu+2, Cr+3, and Mn+2) inhibit the growth of the bacterial
isolates at different rates. Therefore, it indicated that the water source
of the animals was contaminated with both antibiotic residues and
heavy metals.
Abstract: In our research we aimed to test a managerial
approach for the fuzzy front end (FFE) of innovation by creating
controlled experiment/ business case in a breakthrough innovation
development. The experiment was in the sport industry and covered
all aspects of the customer discovery stage from ideation to
prototyping followed by patent application. In the paper we describe
and analyze mile stones, tasks, management challenges, decisions
made to create the break through innovation, evaluate overall
managerial efficiency that was at the considered FFE stage.
We set managerial outcome of the FFE stage as a valid product
concept in hand. In our paper we introduce hypothetical construct
“Q-factor” that helps us in the experiment to distinguish quality of
FFE outcomes.
The experiment simulated for entrepreneur the FFE of innovation
and put on his shoulders responsibility for the outcome of valid
product concept. While developing managerial approach to reach the
outcome there was a decision to look on product concept from the
cognitive psychology and cognitive science point of view. This view
helped us to develop the profile of a person whose projection (mental
representation) of a new product could optimize for a manager or
entrepreneur FFE activities. In the experiment this profile was tested
to develop breakthrough innovation for swimmers. Following the
managerial approach the product concept was created to help
swimmers to feel/sense water. The working prototype was developed
to estimate the product concept validity and value added effect for
customers.
Based on feedback from coachers and swimmers there were strong
positive effect that gave high value for customers, and for the
experiment – the valid product concept being developed by proposed
managerial approach for the FFE.
In conclusions there is a suggestion of managerial approach that
was derived from experiment.
Abstract: Typically, virtual communities exhibit the well-known
phenomenon of participation inequality, which means that only a
small percentage of users is responsible of the majority of
contributions. However, the sustainability of the community requires
that the group of active users must be continuously nurtured with new
users that gain expertise through a participation process. This paper
analyzes the time evolution of Open Source Software (OSS)
communities, considering users that join/abandon the community
over time and several topological properties of the network when
modeled as a social network. More specifically, the paper analyzes
the role of those users rejoining the community and their influence in
the global characteristics of the network.