Abstract: The introduction of degradable plastic materials into
agricultural sectors has represented a promising alternative to
promote green agriculture and environmental friendly of modern
farming practices. Major challenges of developing degradable
agricultural films are to identify the most feasible types of
degradation mechanisms, composition of degradable polymers and
related processing techniques. The incorrect choice of degradable
mechanisms to be applied during the degradation process will cause
premature losses of mechanical performance and strength. In order to
achieve controlled process of agricultural film degradation, the
compositions of degradable agricultural film also important in order
to stimulate degradation reaction at required interval of time and to
achieve sustainability of the modern agricultural practices. A set of
photodegradable polyethylene based agricultural film was developed
and produced, following the selective optimization of processing
parameters of the agricultural film manufacturing system. Example of
agricultural films application for oil palm seedlings cultivation is
presented.
Abstract: Phelipanche ramosa is the most damaging obligate
flowering parasitic weed on wide species of cultivated plants. The
semi-arid regions of the world are considered the main centers of this
parasitic plant that causes heavy infestation. This is due to its
production of high numbers of seeds (up to 200,000) that remain
viable for extended periods (up to 20 years). In this study, 13
treatments for the control of Phelipanche were carried out, which
included agronomic, chemical, and biological treatments and the use
of resistant plant methods. In 2014, a trial was performed at the
Department of Agriculture, Food and Environment, University of
Foggia (southern Italy), on processing tomato (cv ‘Docet’) grown in
pots filled with soil taken from a field that was heavily infested by P.
ramosa). The tomato seedlings were transplanted on May 8, 2014,
into a sandy-clay soil (USDA). A randomized block design with 3
replicates (pots) was adopted. During the growing cycle of the
tomato, at 70, 75, 81 and 88 days after transplantation, the number of
P. ramosa shoots emerged in each pot was determined. The tomato
fruit were harvested on August 8, 2014, and the quantitative and
qualitative parameters were determined. All of the data were
subjected to analysis of variance (ANOVA) using the JMP software
(SAS Institute Inc. Cary, NC, USA), and for comparisons of means
(Tukey's tests). The data show that each treatment studied did not
provide complete control against P. ramosa. However, the virulence
of the attacks was mitigated by some of the treatments tried: radicon
biostimulant, compost activated with Fusarium, mineral fertilizer
nitrogen, sulfur, enzone, and the resistant tomato genotype. It is
assumed that these effects can be improved by combining some of
these treatments with each other, especially for a gradual and
continuing reduction of the “seed bank” of the parasite in the soil.
Abstract: The hydrodynamics and heat transfer characteristics
of a vaporized elongated bubble in a rectangular microchannel have
been simulated based on Cahn-Hilliard phase-field method. In the
simulations, the initially nucleated bubble starts growing as it comes
in contact with superheated water. The growing shape of the bubble
compared well with the available experimental data in the literature.
Abstract: The paper deals with possibilities of interpretation of
iron ore reducibility tests. It presents a mathematical model
developed at Centre ENET, VŠB – Technical University of Ostrava,
Czech Republic for an evaluation of metallurgical material of blast
furnace feedstock such as iron ore, sinter or pellets. According to the
data from the test, the model predicts its usage in blast furnace
technology and its effects on production parameters of shaft
aggregate. At the beginning, the paper sums up the general concept
and experience in mathematical modelling of iron ore reduction. It
presents basic equation for the calculation and the main parts of the
developed model. In the experimental part, there is an example of
usage of the mathematical model. The paper describes the usage of
data for some predictive calculation. There are presented material,
method of carried test of iron ore reducibility. Then there are
graphically interpreted effects of used material on carbon
consumption, rate of direct reduction and the whole reduction
process.
Abstract: The problem of toughening in brittle materials
reinforced by fibers is complex, involving all of the mechanical
properties of fibers, matrix and the fiber/matrix interface, as well as
the geometry of the fiber. Development of new numerical methods
appropriate to toughening simulation and analysis is necessary. In
this work, we have performed simulations and analysis of toughening
in brittle matrix reinforced by randomly distributed fibers by means
of the discrete elements method. At first, we put forward a
mechanical model of toughening contributed by random fibers. Then
with a numerical program, we investigated the stress, damage and
bridging force in the composite material when a crack appeared in the
brittle matrix. From the results obtained, we conclude that: (i) fibers
of high strength and low elasticity modulus are beneficial to
toughening; (ii) fibers of relatively high elastic modulus compared to
the matrix may result in substantial matrix damage due to spalling
effect; (iii) employment of high-strength synthetic fibers is a good
option for toughening. We expect that the combination of the discrete
element method (DEM) with the finite element method (FEM) can
increase the versatility and efficiency of the software developed. The
present work can guide the design of ceramic composites of high
performance through the optimization of the parameters.
Abstract: Fixed-geometry hydrodynamic journal bearings are
one of the best supporting systems for several applications of rotating
machinery. Cylindrical journal bearings present excellent loadcarrying
capacity and low manufacturing costs, but they are subjected
to the oil-film instability at high speeds. An attempt of overcoming
this instability problem has been the development of non-circular
journal bearings. This work deals with an analysis of oil-lubricated
elliptical journal bearings using the finite element method. Steadystate
and dynamic performance characteristics of elliptical bearings
are rendered by zeroth- and first-order lubrication equations obtained
through a linearized perturbation method applied on the classical
Reynolds equation. Four-node isoparametric rectangular finite
elements are employed to model the bearing thin film flow. Curves of
elliptical bearing load capacity and dynamic force coefficients are
rendered at several operating conditions. The results presented in this
work demonstrate the influence of the bearing ellipticity on its
performance at different loading conditions.
Abstract: The aim of the present study was to examine whether
increasing molybdenum (Mo) concentration affects the growth and
Mo concentration of maize (Zea mays L. cv Norma SC) and
sunflower (Helianthus annuus L. cv Arena PR) seedlings within
laboratory conditions.
In this experiment, calcareous chernozem soil was used and Mo
was supplemented into the soil as ammonium molybdate
[(NH4)6Mo7O24.4H2O] in four different concentrations as follow: 0
(control), 30, 90 and 270 mg·kg-1.
In this study, we found that molybdenum in small amount (30
mg·kg-1) affects positively on growth of maize and sunflower
seedlings, however, higher concentration of Mo reduces the dry
weights of shoots and roots. In the case of maize the highest Mo
treatment (270 mg·kg-1) and in sunflower 90 mg·kg-1 treatment
caused significant reduction in plant growth.
In addition, we observed that molybdenum contents in the roots
and shoots were very low in case of control soil but were
significantly elevated with increasing concentration of Mo treatment.
Only in case of sunflower the highest 270 mg·kg-1 Mo treatment
caused decrease in Mo concentration.
Abstract: The construction industry has been demonstrating
increased growth and importance in Brazil’s national economic
development. This study aims to evaluate the financial performance
of the leading companies in the construction sector in Brazil in the
period from 2009 to 2012. An analysis is made of the capital
structure, liquidity, and profitability of the six largest companies in
the construction sector in Brazil: Brookfield, Cyrela, Gafisa, MRV,
PDG and Rossi. The results are then compared with standard industry
ratios. It was found that among the companies analyzed, MRV and
Cyrela showed the best relative performance in the period under
consideration.
Abstract: This paper discusses the value theory in cultural
heritage and the value theory in environmental economics. Two
economic views of the value theory are compared, within the field of
cultural heritage maintenance and within the field of the environment.
The main aims are to find common features in these two differently
structured theories under the layer of differently defined terms as well
as really differing features of these two approaches; to clear the
confusion which stems from different terminology as in fact these
terms capture the same aspects of reality; and to show possible
inspiration these two perspectives can offer one another. Another aim
is to present these two value systems in one value framework. First,
important moments of the value theory from the economic
perspective are presented, leading to the marginal revolution of (not
only) the Austrian School. Then the theory of value within cultural
heritage and environmental economics are explored. Finally,
individual approaches are compared and their potential mutual
inspiration searched for.
Abstract: Significant quota of Municipal Electrical Energy
consumption is related to Decentralized Air Conditioning which is
mostly provided by evaporative coolers. So the aim is to optimize
design of air conditioners to increase their efficiencies. To achieve
this goal, results of practical standardized tests for 40 evaporative
coolers in different types collected and simultaneously results for
same coolers based on one of EER (Energy Efficiency Ratio)
modeling styles are figured out. By comparing experimental results
of different coolers standardized tests with modeling results,
preciseness of used model is assessed and after comparing gained
preciseness with international standards based on EER for cooling
capacity, aeration, and also electrical energy consumption, energy
label from A (most effective) to G (less effective) is classified; finally
needed methods to optimize energy consumption and coolers’
classification are provided.
Abstract: In this paper, we will give a cryptographic application
over the integral closure O_Lof sextic extension L, namely L is an
extension of Q of degree 6 in the form Q(a,b), which is a rational
quadratic and monogenic extension over a pure monogenic cubic
subfield K generated by a who is a root of monic irreducible
polynomial of degree 2 andb is a root of irreducible polynomial of
degree 3.
Abstract: In this paper, we introduced a gradient-based inverse
solver to obtain the missing boundary conditions based on the
readings of internal thermocouples. The results show that the method
is very sensitive to measurement errors, and becomes unstable when
small time steps are used. The artificial neural networks are shown to
be capable of capturing the whole thermal history on the run-out
table, but are not very effective in restoring the detailed behavior of
the boundary conditions. Also, they behave poorly in nonlinear cases
and where the boundary condition profile is different.
GA and PSO are more effective in finding a detailed
representation of the time-varying boundary conditions, as well as in
nonlinear cases. However, their convergence takes longer. A
variation of the basic PSO, called CRPSO, showed the best
performance among the three versions. Also, PSO proved to be
effective in handling noisy data, especially when its performance
parameters were tuned. An increase in the self-confidence parameter
was also found to be effective, as it increased the global search
capabilities of the algorithm. RPSO was the most effective variation
in dealing with noise, closely followed by CRPSO. The latter
variation is recommended for inverse heat conduction problems, as it
combines the efficiency and effectiveness required by these
problems.
Abstract: In this paper, the problem of steady laminar boundary
layer flow and heat transfer over a permeable exponentially
stretching/shrinking sheet with generalized slip velocity is
considered. The similarity transformations are used to transform the
governing nonlinear partial differential equations to a system of
nonlinear ordinary differential equations. The transformed equations
are then solved numerically using the bvp4c function in MATLAB.
Dual solutions are found for a certain range of the suction and
stretching/shrinking parameters. The effects of the suction parameter,
stretching/shrinking parameter, velocity slip parameter, critical shear
rate and Prandtl number on the skin friction and heat transfer
coefficients as well as the velocity and temperature profiles are
presented and discussed.
Abstract: Long Distance Truck Drivers (LDTDs) have been
found to be a high risk group in the spread of HIV/AIDS globally;
perhaps, due to their high Sexual Risk Behaviours (SRBs).
Interventions for reducing SRBs in trucking population have not been
fully exploited. A quasi-experimental control group pretest-posttest
design was used to assess the efficacy of psycho-education and
behavioural skills training in reducing SRBs among LDTDs. Sixteen
drivers rivers were randomly assigned into either experimental or
control groups using balloting technique. Questionnaire was used as
an instrument for data collection. Repeated measures t-test and
independent t-test were used to test hypotheses. Intervention had
significant effect on the SRBs among LDTDs at post-test (t{7}=
6.01, p
Abstract: Co-crystal is believed to improve the solubility and
dissolution rates and thus, enhanced the bioavailability of poor water
soluble drugs particularly during the oral route of administration.
With the existing of poorly soluble drugs in pharmaceutical industry,
the screening of co-crystal formation using carbamazepine (CBZ) as
a model drug compound with dicarboxylic acids co-crystal formers
(CCF) namely fumaric (FA) and succinic (SA) acids in ethanol has
been studied. The co-crystal formations were studied by varying the
mol ratio values of CCF to CBZ to access the effect of CCF
concentration on the formation of the co-crystal. Solvent evaporation,
slurry and cooling crystallization which representing the solution
based method co-crystal screening were used. Based on the
differential scanning calorimetry (DSC) analysis, the melting point of
CBZ-SA in different ratio was in the range between 188oC-189oC.
For CBZ-FA form A and CBZ-FA form B the melting point in
different ratio were in the range of 174oC-175oC and 185oC-186oC
respectively. The product crystal from the screening was also
characterized using X-ray powder diffraction (XRPD). The XRPD
pattern profile analysis has shown that the CBZ co-crystals with FA
and SA were successfully formed for all ratios studied. The findings
revealed that CBZ-FA co-crystal were formed in two different
polymorphs. It was found that CBZ-FA form A and form B were
formed from evaporation and slurry crystallization methods
respectively. On the other hand, in cooling crystallization method,
CBZ-FA form A was formed at lower mol ratio of CCF to CBZ and
vice versa. This study disclosed that different methods and mol ratios
during the co-crystal screening can affect the outcome of co-crystal
produced such as polymorphic forms of co-crystal and thereof. Thus,
it was suggested that careful attentions is needed during the screening
since the co-crystal formation is currently one of the promising
approach to be considered in research and development for
pharmaceutical industry to improve the poorly soluble drugs.
Abstract: The convective heat and mass transfer in nanofluid
flow through a porous media due to a permeable stretching sheet with
magnetic field, viscous dissipation, chemical reaction and Soret
effects are numerically investigated. Two types of nanofluids, namely
Cu-water and Ag-water were studied. The governing boundary layer
equations are formulated and reduced to a set of ordinary differential
equations using similarity transformations and then solved
numerically using the Keller box method. Numerical results are
obtained for the skin friction coefficient, Nusselt number and
Sherwood number as well as for the velocity, temperature and
concentration profiles for selected values of the governing
parameters. Excellent validation of the present numerical results has
been achieved with the earlier linearly stretching sheet problems in
the literature.
Abstract: Rice husk and kenaf filled with calcium carbonate
(CaCO3) and high density polyethylene (HDPE) composite were
prepared separately using twin-screw extruder at 50rpm. Different
filler loading up to 30 parts of rice husk particulate and kenaf fiber
were mixed with the fixed 30% amount of CaCO3 mineral filler to
produce rice husk/CaCO3/HDPE and kenaf/CaCO3/HDPE hybrid
composites. In this study, the effects of natural fiber for both rice
husk and kenaf in CaCO3/HDPE composite on physical, mechanical
and morphology properties were investigated. Field Emission
Scanning Microscope (FeSEM) was used to investigate the impact
fracture surfaces of the hybrid composite. The property analyses
showed that water absorption increased with the presence of kenaf
and rice husk fillers. Natural fibers in composite significantly
influence water absorption properties due to natural characters of
fibers which contain cellulose, hemicellulose and lignin structures.
The result showed that 10% of additional natural fibers into hybrid
composite had caused decreased flexural strength, however additional
of high natural fiber (>10%) filler loading has proved to increase its
flexural strength.
Abstract: A model was constructed to predict the amount of
solar radiation that will make contact with the surface of the earth in
a given location an hour into the future. This project was supported
by the Southern Company to determine at what specific times during
a given day of the year solar panels could be relied upon to produce
energy in sufficient quantities. Due to their ability as universal
function approximators, an artificial neural network was used to
estimate the nonlinear pattern of solar radiation, which utilized
measurements of weather conditions collected at the Griffin, Georgia
weather station as inputs. A number of network configurations and
training strategies were utilized, though a multilayer perceptron with
a variety of hidden nodes trained with the resilient propagation
algorithm consistently yielded the most accurate predictions. In
addition, a modeled direct normal irradiance field and adjacent
weather station data were used to bolster prediction accuracy. In later
trials, the solar radiation field was preprocessed with a discrete
wavelet transform with the aim of removing noise from the
measurements. The current model provides predictions of solar
radiation with a mean square error of 0.0042, though ongoing efforts
are being made to further improve the model’s accuracy.
Abstract: In this paper, a direct power control (DPC)
strategies have been investigated in order to control a high
power AC/DC converter with time variable load. This converter
is composed of a three level three phase neutral point clamped
(NPC) converter as rectifier and an H-bridge four quadrant
current control converter. In the high power application,
controller not only must adjust the desire outputs but also
decrease the level of distortions which are injected to the network
from the converter. Regarding to this reason and nonlinearity
of the power electronic converter, the conventional controllers
cannot achieve appropriate responses. In this research, the
precise mathematical analysis has been employed to design the
appropriate controller in order to control the time variable
load. A DPC controller has been proposed and simulated using
Matlab/ Simulink. In order to verify the simulation result, a real
time simulator- OPAL-RT- has been employed. In this paper,
the dynamic response and stability of the high power NPC
with variable load has been investigated and compared with
conventional types using a real time simulator. The results proved
that the DPC controller is more stable and has more precise
outputs in comparison with conventional controller.
Abstract: In this study, a computational fluid dynamics (CFD)
model has been developed for studying the effect of surface
roughness profile on the EHL problem. The cylinders contact
geometry, meshing and calculation of the conservation of mass and
momentum equations are carried out using the commercial software
packages ICEMCFD and ANSYS Fluent. The user defined functions
(UDFs) for density, viscosity and elastic deformation of the cylinders
as the functions of pressure and temperature are defined for the CFD
model. Three different surface roughness profiles are created and
incorporated into the CFD model. It is found that the developed CFD
model can predict the characteristics of fluid flow and heat transfer in
the EHL problem, including the main parameters such as pressure
distribution, minimal film thickness, viscosity, and density changes.
The results obtained show that the pressure profile at the center of the
contact area directly relates to the roughness amplitude. A rough
surface with kurtosis value of more than 3 has greater influence over
the fluctuated shape of pressure distribution than in other cases.