Abstract: In this work, thermoelastic damping effect on the hemi- spherical shells is investigated. The material is selected silicon, and heat conduction equation for thermal flow is solved to obtain the temperature profile in which bending approximation with inextensional assumption of the model. Using the temperature profile, eigen-value analysis is performed to get the natural frequencies of hemispherical shells. Effects of mode numbers, radii and radial thicknesses of the model on the natural frequencies are analyzed in detail. Furthermore, the quality factor (Q-factor) is defined, and discussed for the ring and hemispherical shell.
Abstract: In this paper we investigate the electrical
characteristics of a new structure of gate all around strained silicon
nanowire field effect transistors (FETs) with dual dielectrics by
changing the radius (RSiGe) of silicon-germanium (SiGe) wire and
gate dielectric. Indeed the effect of high-κ dielectric on Field Induced
Barrier Lowering (FIBL) has been studied. Due to the higher electron
mobility in tensile strained silicon, the n-type FETs with strained
silicon channel have better drain current compare with the pure Si
one. In this structure gate dielectric divided in two parts, we have
used high-κ dielectric near the source and low-κ dielectric near the
drain to reduce the short channel effects. By this structure short
channel effects such as FIBL will be reduced indeed by increasing
the RSiGe, ID-VD characteristics will be improved. The leakage
current and transfer characteristics, the threshold-voltage (Vt), the
drain induced barrier height lowering (DIBL), are estimated with
respect to, gate bias (VG), RSiGe and different gate dielectrics. For
short channel effects, such as DIBL, gate all around strained silicon
nanowire FET have similar characteristics with the pure Si one while
dual dielectrics can improve short channel effects in this structure.
Abstract: An area-integrating method that uses the technique of total integrated light scatter for evaluating the root mean square height of the surface Sq has been presented in the paper. It is based on the measurement of the scatter power using a flat photodiode integrator rather than an optical sphere or a hemisphere. By this means, one can obtain much less expensive and smaller instruments than traditional ones. Thanks to this, they could find their application for surface control purposes, particularly in small and medium size enterprises. A description of the functioning of the measuring unit as well as the impact caused by different factors on its properties is presented first. Next, results of measurements of the Sq values performed for optical, silicon and metal samples have been shown. It has been also proven that they are in a good agreement with the results obtained using the Ulbricht sphere instrument.
Abstract: The photoluminescence (PL) at 1.55 μm from
semiconducting β-FeSi2 has attracted a noticeable interest for
silicon-based optoelectronic applications. Moreover, its high optical
absorption coefficient (higher than 105 cm-1 above 1.0 eV) allows this
semiconducting material to be used as photovoltanics devices.
A clear PL spectrum for β-FeSi2 was observed by Cu or Au coating
on Si(001). High-crystal-quality β-FeSi2 with a low-level nonradiative
center was formed on a Cu- or Au- reated Si layer. This method of
deposition can be applied to other materials requiring high crystal
quality.
Abstract: Future astronomical projects on large space x-ray
imaging telescopes require novel substrates and technologies for the
construction of their reflecting mirrors. The mirrors must be
lightweight and precisely shaped to achieve large collecting area with
high angular resolution. The new materials and technologies must be
cost-effective. Currently, the most promising materials are glass or
silicon foils. We focused on precise shaping these foils by thermal
forming process. We studied free and forced slumping in the
temperature region of hot plastic deformation and compared the
shapes obtained by the different slumping processes. We measured
the shapes and the surface quality of the foils. In the experiments, we
varied both heat-treatment temperature and time following our
experiment design. The obtained data and relations we can use for
modeling and optimizing the thermal forming procedure.
Abstract: Electron multiplying charge coupled devices (EMCCDs) have revolutionized the world of low light imaging by introducing on-chip multiplication gain based on the impact ionization effect in the silicon. They combine the sub-electron readout noise with high frame rates. Signal-to-noise Ratio (SNR) is an important performance parameter for low-light-level imaging systems. This work investigates the SNR performance of an EMCCD operated in Non-inverted Mode (NIMO) and Inverted Mode (IMO). The theory of noise characteristics and operation modes is presented. The results show that the SNR of is determined by dark current and clock induced charge at high gain level. The optimum SNR performance is provided by an EMCCD operated in NIMO in short exposure and strong cooling applications. In contrast, an IMO EMCCD is preferable.
Abstract: We propose an all optical flip-flop circuit composedof two Silicon-on-insulator microring resonators coupled to straightwaveguides by exploiting the optical bistability behavior due to thenonlinear Kerr effect. We used the transfer matrix analysis toinvestigate continuous wave propagation through microrings, as wellwe considered the nonlinear switching characteristics of an opticaldevice using a double-coupler silicon ring resonator in presence ofthe Kerr nonlinearity, thus obtaining the bistability behavior of theoutput port, the drop port and also inside the silicon microringresonator. It is shown that the bistability behavior depends on thecontrol of the input wavelength.KeywordsAll optical flip-flops, Kerr effect, microringresonator, optical bistability.
Abstract: In this study, the use of silicon NAM (Non-Audible
Murmur) microphone in automatic speech recognition is presented.
NAM microphones are special acoustic sensors, which are attached
behind the talker-s ear and can capture not only normal (audible)
speech, but also very quietly uttered speech (non-audible murmur).
As a result, NAM microphones can be applied in automatic speech
recognition systems when privacy is desired in human-machine communication.
Moreover, NAM microphones show robustness against
noise and they might be used in special systems (speech recognition,
speech conversion etc.) for sound-impaired people. Using a small
amount of training data and adaptation approaches, 93.9% word
accuracy was achieved for a 20k Japanese vocabulary dictation
task. Non-audible murmur recognition in noisy environments is also
investigated. In this study, further analysis of the NAM speech has
been made using distance measures between hidden Markov model
(HMM) pairs. It has been shown the reduced spectral space of NAM
speech using a metric distance, however the location of the different
phonemes of NAM are similar to the location of the phonemes
of normal speech, and the NAM sounds are well discriminated.
Promising results in using nonlinear features are also introduced,
especially under noisy conditions.
Abstract: In recent times there has been a growing interest in the
development of quasi-two-dimensional niobium pentoxide (Nb2O5)
as a semiconductor for the potential electronic applications such as
capacitors, filtration, dye-sensitised solar cells and gas sensing
platforms. Therefore once the purpose is established, Nb2O5 can be
prepared in a number of nano- and sub-micron-structural
morphologies that include rods, wires, belts and tubes. In this study
films of Nb2O5 were prepared on gold plated silicon substrate using
spin-coating technique and subsequently by mechanical exfoliation.
The reason this method was employed was to achieve layers of less
than 15nm in thickness. The sintering temperature of the specimen
was 800oC. The morphology and structural characteristics of the
films were analyzed by Atomic Force Microscopy (AFM), Raman
Spectroscopy, X-ray Photoelectron Spectroscopy (XPS).
Abstract: Adjacent Hall microsensors, comprising a silicon
substrate and four contacts, providing simultaneously two supply inputs and two differential outputs, are characterized. The voltage
related sensitivity is in the order of 0.11T-1, and a cancellation method for offset compensation is used, achieving residual offset in
the micro scale which is also compared to a single Hall plate.
Abstract: Silicon nanowire (SiNW) based thermoelectric device (TED) has potential applications in areas such as chip level cooling/ energy harvesting. It is a great challenge however, to assemble an efficient device with these SiNW. The presence of parasitic in the form of interfacial electrical resistance will have a significant impact on the performance of the TED. In this work, we explore the effect of the electrical contact resistance on the performance of a TED. Numerical simulations are performed on SiNW to investigate such effects on its cooling performance. Intrinsically, SiNW individually without the unwanted parasitic effect has excellent cooling power density. However, the cooling effect is undermined with the contribution of the electrical contact resistance.
Abstract: This paper reports the results of an experimental study
conducted to characterise the gas-liquid multiphase flows
experienced within a vertical riser transporting a range of gas-liquid
flow rates. The scale experiments were performed using an
air/silicone oil mixture within a 6 m long riser. The superficial air
velocities studied ranged from 0.047 to 2.836 m/ s, whilst
maintaining a liquid superficial velocity at 0.047 m/ s. Measurements
of the mean cross-sectional and time average radial void fraction
were obtained using a wire mesh sensor (WMS). The data were
recorded at an acquisition frequency of 1000 Hz over an interval of
60 seconds. For the range of flow conditions studied, the average
void fraction was observed to vary between 0.1 and 0.9. An analysis
of the data collected concluded that the observed void fraction was
strongly affected by the superficial gas velocity, whereby the higher
the superficial gas velocity, the higher was the observed average void
fraction. The average void fraction distributions observed were in
good agreement with the results obtained by other researchers. When
the air-silicone oil flows were fully developed reasonably symmetric
profiles were observed, with the shape of the symmetry profile being
strongly dependent on the superficial gas velocity.
Abstract: The paper proposes the novel design of a 3T XOR gate combining complementary CMOS with pass transistor logic. The design has been compared with earlier proposed 4T and 6T XOR gates and a significant improvement in silicon area and power-delay product has been obtained. An eight transistor full adder has been designed using the proposed three-transistor XOR gate and its performance has been investigated using 0.15um and 0.35um technologies. Compared to the earlier designed 10 transistor full adder, the proposed adder shows a significant improvement in silicon area and power delay product. The whole simulation has been carried out using HSPICE.
Abstract: This paper presents the characterization and design of a capacitive pressure sensor with LC-based 0.35 µm CMOS readout circuit. SPICE is employed to evaluate the characteristics of the readout circuit and COMSOL multiphysics structural analysis is used to simulate the behavior of the pressure sensor. The readout circuit converts the capacitance variation of the pressure sensor into the frequency output. Simulation results show that the proposed pressure sensor has output frequency from 2.50 to 2.28 GHz in a pressure range from 0.1 to 2 MPa almost linearly. The sensitivity of the frequency shift with respect to the applied pressure load is 0.11 GHz/MPa.
Abstract: Polyurethane foam (PUF) is formed by a chemical
reaction of polyol and isocyanate. The aim is to understand the
impact of Silicone on synthesizing polyurethane in differentiate
volume of molding. The method used was one step process, which is
simultaneously caried out a blending polyol (petroleum polyol and
soybean polyol), a TDI (2,4):MDI (4,4-) (80:20), a distilled water,
and a silicone. The properties of the material were measured via a
number of parameters, which are polymer density, compressive
strength, and cellular structures. It is found that density of
polyurethane using silicone with volume of molding either 250 ml or
500 ml is lower than without using silicone.
Abstract: Paper presents knowledge about types of test in area
of materials properties of selected methods of rapid prototyping
technologies. In today used rapid prototyping technologies for
production of models and final parts are used materials in initial state
as solid, liquid or powder material structure. In solid state are used
various forms such as pellets, wire or laminates. Basic range
materials include paper, nylon, wax, resins, metals and ceramics. In
Fused Deposition Modeling (FDM) rapid prototyping technology are
mainly used as basic materials ABS (Acrylonitrile Butadiene
Styrene), polyamide, polycarbonate, polyethylene and polypropylene.
For advanced FDM applications are used special materials as silicon
nitrate, PZT (Piezoceramic Material - Lead Zirconate Titanate),
aluminium oxide, hydroxypatite and stainless steel.
Abstract: We present a label-free biosensor based on
electrochemical impedance spectroscopy for the detection of proinflammatory
cytokine Tumor Necrosis Factor (TNF-α). Secretion of
TNF-α has been correlated to the onset of various diseases including
rheumatoid arthritis, Crohn-s disease etc. Gold electrodes were
patterned on a silicon substrate and self assembled monolayer of
dithiobis-succinimidyl propionate was used to develop the biosensor
which achieved a detection limit of ~57fM. A linear relationship was
also observed between increasing TNF-α concentrations and chargetransfer
resistance within a dynamic range of 1pg/ml – 1ng/ml.
Abstract: Bionanotechnology deals with nanoscopic interactions between nanostructured materials and biological systems. Polymer nanocomposites with optimized biological activity have attracted great attention. Nanoclay is considered as reinforcing nanofiller in manufacturing of high performance nanocomposites. In current study, organomodified-nanoclay with negatively charged silicate layers was incorporated into biomedical grade silicone rubber. Nanoparticle loading has been tailored to enhance cell behavior. Addition of nanoparticles led to improved mechanical properties of substrate with enhanced strength and stiffness while no toxic effects was observed. Results indicated improved viability and proliferation of cells by addition of nanofillers. The improved mechanical properties of the matrix result in proper cell response through adjustment and arrangement of cytoskeletal fibers. Results can be applied in tissue engineering when enhanced substrates are required for improvement of cell behavior for in vivo applications.
Abstract: The aim of this study was to investigate ammonium
exchange capacity of natural and activated clinoptilolite from
Kwazulu-Natal Province, South Africa. X – ray fluorescence (XRF)
analysis showed that the clinoptilolite contained exchangeable ions
of sodium, potassium, calcium and magnesium. This analysis also
confirmed that the zeolite sample had a high silicon composition
compared to aluminium. Batch equilibrium studies were performed
in an orbital shaker and the data fitted the Langmuir isotherm very
well. The ammonium exchange capacity was found to increase with
pH and temperature. Clinoptilolite functionalization with
hydrochloric acid increased its ammonia uptake ability.
Abstract: Silicon is a beneficial element for plant growth. It
helps plants to overcome multiple stresses, alleviates metal toxicity
and improves nutrient imbalance. Field experiment was conducted as
split-split plot arranged in a randomized complete block design with
four replications. Irrigation system include continues flooding and
deficit as main plots and nitrogen rates N0, N46, N92, and N138 kg/ha
as sub plots and silicon rates Si0 & Si500 kg/ha as sub-subplots.
Results indicate that grain yield had not significant difference
between irrigation systems. Flooding irrigation had higher biological
yield than deficit irrigation whereas, no significant difference in grain
and straw yield. Nitrogen application increased grain, biological and
straw yield. Silicon application increased grain, biological and straw
yield but, decreased harvest index. Flooding irrigation had higher
number of total tillers / hill than deficit irrigation, but deficit
irrigation had higher number of fertile tillers / hill than flooding
irrigation. Silicon increased number of filled spikelet and decreased
blank spikelet. With high nitrogen application decreased 1000-grain
weight. It can be concluded that if the nitrogen application was high
and water supplied was available we could have silicon application
until increase grain yield.