Abstract: Solar thermal cooling system was installed on Mechanical Research Center (MRC) Building that is located in Universitas Indonesia, Depok, Indonesia. It is the first cooling system in Indonesia that utilizes solar energy as energy input combined with natural gas; therefore, the control system must be appropriated with the climates. In order to stabilize the cooling capacity and also to maximize the use of solar energy, the system applies some controllers. Constant flow rate and on/off controller are applied for the hot water, chilled water and cooling water pumps. The hot water circulated by pump when the solar radiation is over than 400W/m2, and the chilled water is continually circulated by pump and its temperature is kept constant 7 °C by absorption chiller. The cooling water is also continually circulated until the outlet temperature of cooling tower below than 27 oC. Furthermore, the three-way valve is used to control the hot water for generate vapor on absorption chiller. The system performance using that control system is shown in this study results.
Abstract: The problem under research is that of unpredictable modes occurring in two-stage centrifugal hydraulic pump as a result of hydraulic processes caused by vibrations of structural components. Numerical, analytical and experimental approaches are considered. A hypothesis was developed that the problem of unpredictable pressure decrease at the second stage of centrifugal pumps is caused by cavitation effects occurring upon vibration. The problem has been studied experimentally and theoretically as of today. The theoretical study was conducted numerically and analytically. Hydroelastic processes in dynamic “liquid – deformed structure” system were numerically modelled and analysed. Using ANSYS CFX program engineering analysis complex and computing capacity of a supercomputer the cavitation parameters were established to depend on vibration parameters. An influence domain of amplitudes and vibration frequencies on concentration of cavitation bubbles was formulated. The obtained numerical solution was verified using CFM program package developed in PNRPU. The package is based on a differential equation system in hyperbolic and elliptic partial derivatives. The system is solved by using one of finite-difference method options – the particle-in-cell method. The method defines the problem solution algorithm. The obtained numerical solution was verified analytically by model problem calculations with the use of known analytical solutions of in-pipe piston movement and cantilever rod end face impact. An infrastructure consisting of an experimental fast hydro-dynamic processes research installation and a supercomputer connected by a high-speed network, was created to verify the obtained numerical solutions. Physical experiments included measurement, record, processing and analysis of data for fast processes research by using National Instrument signals measurement system and Lab View software. The model chamber end face oscillated during physical experiments and, thus, loaded the hydraulic volume. The loading frequency varied from 0 to 5 kHz. The length of the operating chamber varied from 0.4 to 1.0 m. Additional loads weighed from 2 to 10 kg. The liquid column varied from 0.4 to 1 m high. Liquid pressure history was registered. The experiment showed dependence of forced system oscillation amplitude on loading frequency at various values: operating chamber geometrical dimensions, liquid column height and structure weight. Maximum pressure oscillation (in the basic variant) amplitudes were discovered at loading frequencies of approximately 1,5 kHz. These results match the analytical and numerical solutions in ANSYS and CFM.
Abstract: Quality Function Deployment (QFD) was developed in 1960 in Japan and introduced in 1983 in America and Europe. The paper presents a real application of this technique in a way that the method of applying QFD in design and production aero fuel pumps has been considered. While designing a product and in order to apply system engineering process, the first step is identification customer needs then its transition to engineering parameters. Since each change in deign after production process leads to extra human costs and also increase in products quality risk, QFD can make benefits in sale by meeting customer expectations. Since the needs identified as well, the use of QFD tool can lead to increase in communications and less deviation in design and production phases, finally it leads to produce the products with defined technical attributes.
Abstract: This paper describes two methods for the reduction of
the peak input current during the boosting of Dickson charge pumps.
Both methods are implemented in the fully integrated Dickson charge
pumps of a high-voltage display driver chip for smart-card
applications. Experimental results reveal good correspondence with
Spice simulations and show a reduction of the peak input current by a
factor of 6 during boosting.
Abstract: An Energetic and exergetic analysis is conducted on a
Steam Turbine Power Plant of an existing Phosphoric Acid Factory.
The heat recovery systems used in different parts of the plant are also
considered in the analysis. Mass, thermal and exergy balances are
established on the main compounds of the factory. A numerical code
is established using EES software to perform the calculations
required for the thermal and exergy plant analysis. The effects of the
key operating parameters such as steam pressure and temperature,
mass flow rate as well as seawater temperature, on the cycle
performances are investigated. A maximum Exergy Loss Rate of about 72% is obtained for the
melters, followed by the condensers, heat exchangers and the pumps.
The heat exchangers used in the phosphoric acid unit present
exergetic efficiencies around 33% while 60% to 72% are obtained for
steam turbines and blower. For the explored ranges of HP steam
temperature and pressure, the exergy efficiencies of steam turbine
generators STGI and STGII increase of about 2.5% and 5.4%
respectively. In the same way optimum HP steam flow rate values,
leading to the maximum exergy efficiencies are defined.
Abstract: Excessive vibration means increased wear, increased
repair efforts, bad product selection & quality and high energy
consumption. This may be sometimes experienced by cavitation or
suction/discharge recirculation which could occur only when net
positive suction head available NPSHA drops below the net positive
suction head required NPSHR. Cavitation can cause axial surging, if it
is excessive, will damage mechanical seals, bearings, possibly other
pump components frequently, and shorten the life of the impeller.
Efforts have been made to explain Suction Energy (SE), Specific
Speed (Ns), Suction Specific Speed (Nss), NPSHA, NPSHR & their
significance, possible reasons of cavitation /internal recirculation, its
diagnostics and remedial measures to arrest and prevent cavitation in
this paper. A case study is presented by the author highlighting that
the root cause of unwanted noise and vibration is due to cavitation,
caused by high specific speeds or inadequate net- positive suction
head available which results in damages to material surfaces of
impeller & suction bells and degradation of machine performance, its
capacity and efficiency too. Author strongly recommends revisiting
the technical specifications of CW pumps to provide sufficient NPSH
margin ratios >1.5, for future projects and Nss be limited to 8500 -
9000 for cavitation free operation.
Abstract: Cryosorption pumps are considered safe, quiet, and
ultra-high vacuum production pumps which have their application
from Semiconductor industries to ITER [International Thermonuclear
Experimental Reactor] units. The principle of physisorption of gases
over highly porous materials like activated charcoal at cryogenic
temperatures (below -1500°C) is involved in determining the
pumping speed of gases like Helium, Hydrogen, Argon, and
Nitrogen. This paper aims at providing detailed overview of
development of Cryosorption pump and characterization of different
activated charcoal materials that optimizes the performance of the
pump. Different grades of charcoal were tested in order to determine
the pumping speed of the pump and were compared with
commercially available Varian cryopanel. The results for bare panel,
bare panel with adhesive, cryopanel with pellets, and cryopanel with
granules were obtained and compared. The comparison showed that
cryopanel adhered with small granules gave better pumping speeds
than large sized pellets.
Abstract: In recent years, new techniques for solving complex
problems in engineering are proposed. One of these techniques is
JPSO algorithm. With innovative changes in the nature of the jump
algorithm JPSO, it is possible to construct a graph-based solution
with a new algorithm called G-JPSO. In this paper, a new algorithm
to solve the optimal control problem Fletcher-Powell and optimal
control of pumps in water distribution network was evaluated.
Optimal control of pumps comprise of optimum timetable operation
(status on and off) for each of the pumps at the desired time interval.
Maximum number of status on and off for each pumps imposed to the
objective function as another constraint. To determine the optimal
operation of pumps, a model-based optimization-simulation
algorithm was developed based on G-JPSO and JPSO algorithms.
The proposed algorithm results were compared well with the ant
colony algorithm, genetic and JPSO results. This shows the
robustness of proposed algorithm in finding near optimum solutions
with reasonable computational cost.
Abstract: Carefully scheduling the operations of pumps can be
resulted to significant energy savings. Schedules can be defined
either implicit, in terms of other elements of the network such as tank
levels, or explicit by specifying the time during which each pump is
on/off. In this study, two new explicit representations based on timecontrolled
triggers were analyzed, where the maximum number of
pump switches was established beforehand, and the schedule may
contain fewer switches than the maximum. The optimal operation of
pumping stations was determined using a Jumping Particle Swarm
Optimization (JPSO) algorithm to achieve the minimum energy cost.
The model integrates JPSO optimizer and EPANET hydraulic
network solver. The optimal pump operation schedule of VanZyl
water distribution system was determined using the proposed model
and compared with those from Genetic and Ant Colony algorithms.
The results indicate that the proposed model utilizing the JPSO
algorithm is a versatile management model for the operation of realworld
water distribution system.
Abstract: This paper presents the design process of a high
performance 3-phase 3.7 kW 2-pole line start permanent magnet
synchronous motor for pumping system. A method was proposed to
study the starting torque characteristics considering line start with
high inertia load. A d-q model including cage was built to study the
synchronization capability. Time-stepping finite element method
analysis was utilized to accurately predict the dynamic and transient
performance, efficiency, starting current, speed curve and etc.
Considering the load torque of pumps during starting stage, the rotor
bar was designed with minimum demagnetization of permanent
magnet caused by huge starting current.
Abstract: This paper presents the design and fabrication of a
novel piezoelectric actuator for a gas micro pump with check valve
having the advantages of miniature size, light weight and low power
consumption. The micro pump is designed to have eight major
components, namely a stainless steel upper cover layer, a piezoelectric
actuator, a stainless steel diaphragm, a PDMS chamber layer, two
stainless steel channel layers with two valve seats, a PDMS check
valve layer with two cantilever-type check valves and an acrylic
substrate. A prototype of the gas micro pump, with a size of 52 mm ×
50 mm × 5.0 mm, is fabricated by precise manufacturing. This device
is designed to pump gases with the capability of performing the
self-priming and bubble-tolerant work mode by maximizing the stroke
volume of the membrane as well as the compression ratio via
minimization of the dead volume of the micro pump chamber and
channel. By experiment apparatus setup, we can get the real-time
values of the flow rate of micro pump and the displacement of the
piezoelectric actuator, simultaneously. The gas micro pump obtained
higher output performance under the sinusoidal waveform of 250 Vpp.
The micro pump achieved the maximum pumping rates of 1185
ml/min and back pressure of 7.14 kPa at the corresponding frequency
of 120 and 50 Hz.
Abstract: In wastewater treatment processes, aeration introduces
air into a liquid. In these systems, air is introduced by different
devices submerged in the wastewater. Smaller bubbles result in more
bubble surface area per unit of volume and higher oxygen transfer
efficiency. Jet pumps are devices that use air bubbles and are widely
used in wastewater treatment processes. The principle of jet pumps is
their ability to transfer energy of one fluid, called primary or motive,
into a secondary fluid or gas. These pumps have no moving parts and
are able to work in remote areas under extreme conditions. The
objective of this work is to study experimentally the characteristics of
the jet pump and the size of air bubbles in the laboratory water tank.
The effect of flow rate ratio on pump performance is investigated in
order to have a better understanding about pump behavior under
various conditions, in order to determine the efficiency of receiving
air bubbles different sizes. The experiments show that we should take
care when increasing the flow rate ratio while seeking to decrease
bubble size in the outlet flow. This study will help improve and
extend the use of the jet pump in many practical applications.
Abstract: The effects of the pumping wavelength and their power
on the gain flattening of a fiber Raman amplifier (FRA) are
investigated. The multi-wavelength pumping scheme is utilized to
achieve gain flatness in FRA. It is proposed that gain flatness
becomes better with increase in number of pumping wavelengths
applied. We have achieved flat gain with 0.27 dB fluctuation in a
spectral range of 1475-1600 nm for a Raman fiber length of 10 km by
using six pumps with wavelengths with in the 1385-1495 nm interval.
The effect of multi-wavelength pumping scheme on gain saturation in
FRA is also studied. It is proposed that gain saturation condition gets
improved by using this scheme and this scheme is more useful for
higher spans of Raman fiber length.
Abstract: Advances in the use of health care technology have
resulted in increased adverse events (AEs) related to the use of
medical devices. The study focused on the existing reporting systems.
This study was conducted in a tertiary care public sector hospital.
Devices included Syringe infusion pumps, Cardiac monitors, Pulse
oximeters, Ventilators and Defibrillators. A total of 211 respondents
were recruited. Interviews were held with 30 key informants. Medical
records were scrutinized. Relevant statistical tests were used.
Resident doctors reported maximum frequency of AEs, followed
by nurses; and least by consultants. A significant association was
found between the cadre of health care personnel and awareness that
the patients and bystanders have a risk of sustaining AE. Awareness
regarding reporting of AEs was low, and it was generally done
verbally. Other critical findings are discussed in the light of the
barriers to reporting, reasons for non-compliance, recording system,
and so on.
Abstract: Presently, engine cooling pump is driven by toothed
belt. Therefore, the pump speed is dependent on engine speed which
varies their output. At normal engine operating conditions (Higher
RPM and low load, Higher RPM and high load), mechanical water
pumps in existing engines are inevitably oversized and so the use of
an electric water pump together with state-of-the-art thermal
management of the combustion engine has measurable advantages.
Demand-driven cooling, particularly in the cold-start phase, saves
fuel (approx 3 percent) and leads to a corresponding reduction in
emissions. The lack of dependence on a mechanical drive also results
in considerable flexibility in component packaging within the engine
compartment. This paper describes the testing and comparison of
existing mechanical water pump with that of the electric water pump.
When the existing mechanical water pump is replaced with the new
electric water pump the percentage gain in system efficiency is also
discussed.
Abstract: The crude oil in an oil well exists in various phases
such as gas, seawater, and sand, as well as oil. Therefore, a phase
separator is needed at the front of a single-phase pump for
pressurization and transfer. On the other hand, the application of a
multiphase pump can provide such advantages as simplification of the
equipment structure and cost savings, because there is no need for a
phase separation process. Therefore, the crude oil transfer method
using a multiphase pump is being applied to recently developed oil
wells. Due to this increase in demand, technical demands for the
development of multiphase pumps are sharply increasing, but the
progress of research into related technologies is insufficient, due to the
nature of multiphase pumps that require high levels of skills. This
study was conducted to verify the reliability of pump performance
evaluation using numerical analysis, which is the basis of the
development of a multiphase pump. For this study, a model was
designed by selecting the specifications of this study. The performance
of the designed model was evaluated through numerical analysis and
experiment. The results of the performance evaluation were compared
to verify the reliability of the result using numerical analysis.
Abstract: Surplus electricity can be converted into potential energy via pumped hydroelectric storage for future usage. Similarly, thermo-electric energy storage (TEES) uses heat pumps equipped with thermal storage to convert electrical energy into thermal energy; the stored energy is then converted back into electrical energy when necessary using a heat engine. The greatest advantage of this method is that, unlike pumped hydroelectric storage and compressed air energy storage, TEES is not restricted by geographical constraints. In this study, performance variation of the TEES according to the changes in cold-side storage temperature was investigated by simulation method.
Abstract: The subject of this paper is the design analysis of a single well power production unit from low enthalpy geothermal resources. A complexity of the project is defined by a low temperature heat source that usually makes such projects economically disadvantageous using the conventional binary power plant approach. A proposed new compact design is numerically analyzed. This paper describes a thermodynamic analysis, a working fluid choice, downhole heat exchanger (DHE) and turbine calculation results. The unit is able to produce 321 kW of electric power from a low enthalpy underground heat source utilizing n-Pentane as a working fluid. A geo-pressured reservoir located in Vermilion Parish, Louisiana, USA is selected as a prototype for the field application. With a brine temperature of 126 , the optimal length of DHE is determined as 304.8 m (1000ft). All units (pipes, turbine, and pumps) are chosen from commercially available parts to bring this project closer to the industry requirements. Numerical calculations are based on petroleum industry standards. The project is sponsored by the Department of Energy of the US.
Abstract: Ground Coupled Heat Pumps (GCHPs) exploit effectively the heat capacity of the ground, with the use of Ground Heat Exchangers (GHE). Depending on the mode of operation of the GCHPs, GHEs dissipate or absorb heat from the ground. For sizing the GHE the thermal properties of the ground need to be known. This paper gives information about the density, thermal conductivity, specific heat and thermal diffusivity of various lithologies encountered in Cyprus with various relations between these properties being examined through comparison and modeling. The results show that the most important correlation is the one encountered between thermal conductivity and thermal diffusivity with both properties showing similar response to the inlet and outlet flow temperature of vertical and horizontal heat exchangers.
Abstract: Cavitation is one of the most well-known process faults that may occur in different industrial equipment especially centrifugal pumps. Cavitation also may happen in water pumps and turbines. Sometimes cavitation has been severe enough to wear holes in the impeller and damage the vanes to such a degree that the impeller becomes very ineffective. More commonly, the pump efficiency will decrease significantly during cavitation and continue to decrease as damage to the impeller increases. Typically, when cavitation occurs, an audible sound similar to ‘marbles’ or ‘crackling’ is reported to be emitted from the pump. In this paper, the most effective monitoring items and techniques in detecting cavitation discussed in details. Besides, some successful solutions for solving this problem for sea water vertical Centrifugal lift Pump discussed through a case history related to Iran oil industry. Furthermore, balance line modification, strainer choking and random resonance in sea water pumps discussed. In addition, a new Method for diagnosing mechanical conditions of sea water vertical Centrifugal lift Pumps introduced. This method involves disaggregating bus current by device into disaggregated currents having correspondences with operating currents in response to measured bus current. Moreover, some new patents and innovations in mechanical sea water pumping and cooling systems discussed in this paper.