Abstract: This paper is focused on the CFD simulation of the radiaxial pump (i.e. mixed flow pump) with the aim to detect the reasons of Y-Q characteristic instability. The main reasons of pressure pulsations were detected by means of the analysis of velocity and pressure fields within the pump combined with the theoretical approach. Consequently, the modifications of spiral case and pump suction area were made based on the knowledge of flow conditions and the shape of dissipation function. The primary design of pump geometry was created as the base model serving for the comparison of individual modification influences. The basic experimental data are available for this geometry. This approach replaced the more complicated and with respect to convergence of all computational tasks more difficult calculation for the compressible liquid flow. The modification of primary pump consisted in inserting the three fins types. Subsequently, the evaluation of pressure pulsations, specific energy curves and visualization of velocity fields were chosen as the criterion for successful design.
Abstract: The use of energy dissipation systems for seismic applications has increased worldwide, thus it is necessary to develop practical and modern criteria for their optimal design. Here, a direct displacement-based seismic design approach for frame buildings with hysteretic energy dissipation systems (HEDS) is applied. The building is constituted by two individual structural systems consisting of: 1) a main elastic structural frame designed for service loads; and 2) a secondary system, corresponding to the HEDS, that controls the effects of lateral loads. The procedure implies to control two design parameters: a) the stiffness ratio (α=Kframe/Ktotal system), and b) the strength ratio (γ=Vdamper/Vtotal system). The proposed damage-controlled approach contributes to the design of a more sustainable and resilient building because the structural damage is concentrated on the HEDS. The reduction of the design displacement spectrum is done by means of a damping factor (recently published) for elastic structural systems with HEDS, located in Mexico City. Two limit states are verified: serviceability and near collapse. Instead of the traditional trial-error approach, a procedure that allows the designer to establish the preliminary sizes of the structural elements of both systems is proposed. The design methodology is applied to an 8-story steel building with buckling restrained braces, located in soft soil of Mexico City. With the aim of choosing the optimal design parameters, a parametric study is developed considering different values of હ and . The simplified methodology is for preliminary sizing, design, and evaluation of the effectiveness of HEDS, and it constitutes a modern and practical tool that enables the structural designer to select the best design parameters.
Abstract: The present work attempts to investigate the
combustion, performance and emission characteristics of an existing
single-cylinder four-stroke compression-ignition engine operated in
dual-fuel mode with hydrogen as an alternative fuel. Environmental
concerns and limited amount of petroleum fuels have caused interests
in the development of alternative fuels like hydrogen for internal
combustion (IC) engines. In this experimental investigation, a diesel
engine is made to run using hydrogen in dual fuel mode with diesel,
where hydrogen is introduced into the intake manifold using an LPGCNG
injector and pilot diesel is injected using diesel injectors. A
Timed Manifold Injection (TMI) system has been developed to vary
the injection strategies. The optimized timing for the injection of
hydrogen was 10^0 CA after top dead center (ATDC). From the study
it was observed that with increasing hydrogen rate, enhancement in
brake thermal efficiency (BTHE) of the engine has been observed
with reduction in brake specific energy consumption (BSEC).
Furthermore, Soot contents decrease with an increase in indicated
specific NOx emissions with the enhancement of hydrogen flow rate.
Abstract: The thermal performance of a solar water heating with
1.00 m2 flat plate collectors in Cascavel - PR, is which presented in
this article, paper presents the solution to leverage the marketing of
solar heating systems through detailed constituent materials of the
solar collector studies, these abundant materials in construction, such
as expanded polyethylene, PVC, aluminum and glass tubes, mixing
them with new materials to minimize loss of efficiency while
decreasing its cost. The system was tested during months and the
collector obtained maximum recorded temperature of outlet fluid of
55°C, while the maximum temperature of the water at the bottom of
the hot water tank was 35°C. The average daily energy collected was
19.6 MJ/d; the energy supplied by the solar plate was 16.2 MJ/d; the
loss in the feed pipe was 3.2 MJ/d; the solar fraction was 32.2%, the
efficiency of the collector was 45.6% and the efficiency of the system
was 37.8%.
Abstract: In this research the effect of moisture at three levels
(47, 57, and 67 w.b.%) on the physical properties of the Pofaki pea
variety including, dimensions, geometric mean diameter, volume,
sphericity index and the surface area was determined. The influence
of different moisture levels (47, 57 and 67 w.b.%), in two loading
orientation (longitudinal and transverse) and three loading speed (4,6
and 8 mm min-1) on the mechanical properties of pea such as
maximum deformation, rupture force, rupture energy, toughness and
the power to break the pea was investigated. It was observed in the
physical properties that moisture changes were affective at 1% on,
dimensions, geometric mean diameter, volume, sphericity index and
the surface area. It was observed in the mechanical properties that
moisture changes were effective at 1% on, maximum deformation,
rupture force, rupture energy, toughness and the power to break.
Loading speed was effective on maximum deformation, rupture
force, rupture energy at 1% and it was effective on toughness at 5%.
Loading orientation was effective on maximum deformation, rupture
force, rupture energy, toughness at 1% and it was effective on power
at 5%. The mutual effect of speed and orientation were effective on
rupture energy at 1% and were effective on toughness at 5%
probability. The mutual effect of moisture and speed were effective
on rupture force and rupture energy at 1% and were effective on
toughness 5% probability. The mutual effect of orientation and
moisture on rupture energy and toughness were effective at 1%.
Abstract: This paper is concerned with knowledge representation
and extraction of fuzzy if-then rules using Interval Type-2
Context-based Fuzzy C-Means clustering (IT2-CFCM) with the aid of
fuzzy granulation. This proposed clustering algorithm is based on
information granulation in the form of IT2 based Fuzzy C-Means
(IT2-FCM) clustering and estimates the cluster centers by preserving
the homogeneity between the clustered patterns from the IT2 contexts
produced in the output space. Furthermore, we can obtain the
automatic knowledge representation in the design of Radial Basis
Function Networks (RBFN), Linguistic Model (LM), and Adaptive
Neuro-Fuzzy Networks (ANFN) from the numerical input-output data
pairs. We shall focus on a design of ANFN in this paper. The
experimental results on an estimation problem of energy performance
reveal that the proposed method showed a good knowledge
representation and performance in comparison with the previous
works.
Abstract: We investigate relaxation dynamics of a quantum
dipole emitter (QDE), e.g., a molecule or quantum dot, located near a
metal nanoparticle (MNP) exhibiting a dipolar localized surface
plasmon (LSP) resonance at the frequency of the QDE radiative
transition. It is shown that under the condition of the QDE-MNP
characteristic relaxation time being much shorter than that of the
QDE in free-space but much longer than the LSP lifetime. It is also
shown that energy dissipation in the QDE-MNP system is relatively
weak with the probability of the photon emission being about 0.75, a
number which, rather surprisingly, does not explicitly depend on the
metal absorption characteristics. The degree of entanglement
measured by the concurrency takes the maximum value, while the
distances between the QDEs and metal ball approximately are equal.
Abstract: The capability of exploiting the electronic charge and
spin properties simultaneously in a single material has made diluted
magnetic semiconductors (DMS) remarkable in the field of
spintronics. We report the designing of DMS based on zinc-blend
ZnO doped with Cr impurity. The full potential linearized augmented
plane wave plus local orbital FP-L(APW+lo) method in density
functional theory (DFT) has been adapted to carry out these
investigations. For treatment of exchange and correlation energy,
generalized gradient approximations have been used. Introducing Cr
atoms in the matrix of ZnO has induced strong magnetic moment
with ferromagnetic ordering at stable ground state. Cr:ZnO was found
to favor the short range magnetic interaction that
reflect tendency of Cr clustering. The electronic structure of ZnO is
strongly influenced in the presence of Cr impurity atoms where
impurity bands appear in the band gap.
Abstract: The material selection in the design of the sandwich
structures is very crucial aspect because of the positive or negative
influences of the base materials to the mechanical properties of the
entire panel. In the literature, it was presented that the selection of the
skin and core materials plays very important role on the behavior of
the sandwich. Beside this, the use of the correct adhesive can make
the whole structure to show better mechanical results and behavior.
In the present work, the static three-point bending tests were
performed on the sandwiches having an aluminum alloy foam core,
the skins made of three different types of fabrics and two different
commercial adhesives (flexible polyurethane and toughened epoxy
based) at different values of support span distances by aiming the
analyses of their flexural performance in terms of absorbed energy,
peak force values and collapse mechanisms. The main results of the
flexural loading are: force-displacement curves obtained after the
bending tests, peak force and absorbed energy values, collapse
mechanisms and adhesion quality. The experimental results presented
that the sandwiches with epoxy based toughened adhesive and the
skins made of S-Glass Woven fabrics indicated the best adhesion
quality and mechanical properties. The sandwiches with toughened
adhesive exhibited higher peak force and energy absorption values
compared to the sandwiches with flexible adhesive. The use of these
sandwich structures can lead to a weight reduction of the transport
vehicles, providing an adequate structural strength under operating
conditions.
Abstract: The performance of box-type solar cookers has been
reported by several researchers but little attention was paid to the
effect of the type of insulation material on the energy and exergy
efficiency of these cookers. This research aimed at evaluating the
energy and exergy efficiencies of the box-type cookers containing
different insulation materials. Energy and exergy efficiencies of five
box-type solar cookers insulated with maize cob, air (control), maize
husk, coconut coir and polyurethane foam respectively were obtained
over a period of three years. The cookers were evaluated using water
heating test procedures in determining the energy and exergy
analysis. The results were subjected to statistical analysis using
ANOVA. The result shows that the average energy input for the five
solar cookers were: 245.5, 252.2, 248.7, 241.5 and 245.5J
respectively while their respective average energy losses were: 201.2,
212.7, 208.4, 189.1 and 199.8J. The average exergy input for five
cookers were: 228.2, 234.4, 231.1, 224.4 and 228.2J respectively
while their respective average exergy losses were: 223.4, 230.6,
226.9, 218.9 and 223.0J. The energy and exergy efficiency was
highest in the cooker with coconut coir (37.35 and 3.90%
respectively) in the first year but was lowest for air (11 and 1.07%
respectively) in the third year. Statistical analysis showed significant
difference between the energy and exergy efficiencies over the years.
These results reiterate the importance of a good insulating material
for a box-type solar cooker.
Abstract: Dental porcelain composites reinforced and toughened
by 20 wt.% tetragonal zirconia (3Y-TZP) were processed by hot
pressing at 1000°C. Two types of particles were tested: yttriastabilized
zirconia (ZrO2–3%Y2O3) agglomerates and pre-sintered
yttria-stabilized zirconia (ZrO2–3%Y2O3) particles. The composites
as well as the reinforcing particles were analyzed by the means of
optical and Scanning Electron Microscopy (SEM), Energy Dispersion
Spectroscopy (EDS) and X-Ray Diffraction (XRD). The mechanical
properties were obtained by the transverse rupture strength test. Wear
tests were also performed on the composites and monolithic
porcelain. The best mechanical results were displayed by the
porcelain reinforced with the pre-sintered ZrO2–3%Y2O3
agglomerates.
Abstract: Flexible AC Transmission Systems (FACTS) is
granting a new group of advanced power electronic devices emerging
for enhancement of the power system performance. Unified Power
Flow Controller (UPFC) is a recent version of FACTS devices for
power system applications. The back-up energy supply system
incorporated with UPFC is providing a complete control of real and
reactive power at the same time and hence is competent to improve
the performance of an electrical power system. In this article, backup
energy supply unit such as superconducting magnetic energy storage
(SMES) is integrated with UPFC. In addition, comparative
exploration of UPFC–battery, UPFC–UC and UPFC–SMES
performance is evaluated through the vibrant simulation by using
MATLAB/Simulink software.
Abstract: The design philosophy of building structure has been
changing time to time. The reason for this is because of an increase of
human inertest, an improved building materials and technology that
will impact how we live, to speed up construction period and natural
effect which includes earthquake disasters and environmental effect.
One technique which takes in to account the above case is using a
prefabricable structural system. In which each and every structural
element is designed and prefabricated and assembled on a site so that
the construction speed is increased and the environmental impact is
also enhanced. This system has an immense advantage such as: reduce
construction cost, reusable, recyclable, speed up construction period
and less environmental effect. In this study, it is tried to present some
of the developed and evaluated structural elements of building
structures.
Abstract: The biodegradable family of polymers
polyhydroxyalkanoates is an interesting substitute for convectional
fossil-based plastics. However, the manufacturing and environmental
impacts associated with their production via intracellular bacterial
fermentation are strongly dependent on the raw material used and on
energy consumption during the extraction process, limiting their
potential for commercialization. Industrial wastewater is studied in
this paper as a promising alternative feedstock for waste valorization.
Based on results from laboratory and pilot-scale experiments, a
conceptual process design, techno-economic analysis and life cycle
assessment are developed for the large-scale production of the most
common type of polyhydroxyalkanoate, polyhydroxbutyrate.
Intracellular polyhydroxybutyrate is obtained via fermentation of
microbial community present in industrial wastewater and the
downstream processing is based on chemical digestion with
surfactant and hypochlorite. The economic potential and
environmental performance results help identifying bottlenecks and
best opportunities to scale-up the process prior to industrial
implementation. The outcome of this research indicates that the
fermentation of wastewater towards PHB presents advantages
compared to traditional PHAs production from sugars because the
null environmental burdens and financial costs of the raw material in
the bioplastic production process. Nevertheless, process optimization
is still required to compete with the petrochemicals counterparts.
Abstract: Problems insulation of building structures is often
closely connected with the problem of moisture remediation. In the
case of historic buildings or if only part of the redevelopment of
envelope of structures, it is not possible to apply the classical external
thermal insulation composite systems. This application is mostly
effective thermal insulation plasters with high porosity and controlled
capillary properties which assures improvement of thermal properties
construction, its diffusion openness towards the external environment
and suitable treatment capillary properties of preventing the
penetration of liquid moisture and salts thereof toward the outer
surface of the structure.
With respect to the current trend of reducing the energy
consumption of building structures and reduce the production of CO2
is necessary to develop capillary-active materials characterized by
their low density, low thermal conductivity while maintaining good
mechanical properties. The aim of researchers at the Faculty of Civil
Engineering, Brno University of Technology is the development and
study of hygrothermal behaviour of optimal materials for thermal
insulation and rehabilitation of building structures with the possible
use of alternative, less energy demanding binders in comparison with
conventional, frequently used binder, which represents cement.
The paper describes the evaluation of research activities aimed at
the development of thermal insulation and repair materials using
lightweight aggregate and alternative binders such as metakaolin and
finely ground fly ash.
Abstract: Significant quota of Municipal Electrical Energy
consumption is related to Decentralized Air Conditioning which is
mostly provided by evaporative coolers. So the aim is to optimize
design of air conditioners to increase their efficiencies. To achieve
this goal, results of practical standardized tests for 40 evaporative
coolers in different types collected and simultaneously results for
same coolers based on one of EER (Energy Efficiency Ratio)
modeling styles are figured out. By comparing experimental results
of different coolers standardized tests with modeling results,
preciseness of used model is assessed and after comparing gained
preciseness with international standards based on EER for cooling
capacity, aeration, and also electrical energy consumption, energy
label from A (most effective) to G (less effective) is classified; finally
needed methods to optimize energy consumption and coolers’
classification are provided.
Abstract: Gypsum (CaSO4.2H2O) is a mineral that is found in
large quantities in the Turkey and in the World. In this study, the
dissolution of this mineral in the diammonium hydrogen phosphate
solutions has been studied. The dissolution and dissolution kinetics of
gypsum in diammonium hydrogen phosphate solutions will be useful
for evaluating of solid wastes containing gypsum. Parameters such as
diammonium hydrogen phosphate concentration, temperature and
stirring speed affecting on the dissolution rate of the gypsum in
diammonium hydrogen phosphate solutions were investigated. In
experimental studies have researched effectiveness of the selected
parameters. The dissolution of gypsum were examined in two parts at
low and high temperatures. The experimental results were
successfully correlated by linear regression using Statistica program.
Dissolution curves were evaluated shrinking core models for solidfluid
systems. The activation energy was found to be 34.58 kJ/mol
and 44.45 kJ/mol for the low and the high temperatures. The
dissolution of gypsum was controlled by chemical reaction both low
temperatures and high temperatures.
Abstract: Incineration of municipal solid waste (MSW) is one of
the key scopes in the global clean energy strategy. A computational
fluid dynamics (CFD) model was established in order to reveal these
features of the combustion process in a fixed porous bed of MSW.
Transporting equations and process rate equations of the waste bed
were modeled and set up to describe the incineration process,
according to the local thermal conditions and waste property
characters. Gas phase turbulence was modeled using k-ε turbulent
model and the particle phase was modeled using the kinetic theory of
granular flow. The heterogeneous reaction rates were determined
using Arrhenius eddy dissipation and the Arrhenius-diffusion
reaction rates. The effects of primary air flow rate and temperature in
the burning process of simulated MSW are investigated
experimentally and numerically. The simulation results in bed are
accordant with experimental data well. The model provides detailed
information on burning processes in the fixed bed, which is otherwise
very difficult to obtain by conventional experimental techniques.
Abstract: A model was constructed to predict the amount of
solar radiation that will make contact with the surface of the earth in
a given location an hour into the future. This project was supported
by the Southern Company to determine at what specific times during
a given day of the year solar panels could be relied upon to produce
energy in sufficient quantities. Due to their ability as universal
function approximators, an artificial neural network was used to
estimate the nonlinear pattern of solar radiation, which utilized
measurements of weather conditions collected at the Griffin, Georgia
weather station as inputs. A number of network configurations and
training strategies were utilized, though a multilayer perceptron with
a variety of hidden nodes trained with the resilient propagation
algorithm consistently yielded the most accurate predictions. In
addition, a modeled direct normal irradiance field and adjacent
weather station data were used to bolster prediction accuracy. In later
trials, the solar radiation field was preprocessed with a discrete
wavelet transform with the aim of removing noise from the
measurements. The current model provides predictions of solar
radiation with a mean square error of 0.0042, though ongoing efforts
are being made to further improve the model’s accuracy.
Abstract: Parabolic solar trough systems have seen limited
deployments in cold northern climates as they are more suitable for
electricity production in southern latitudes. A numerical dynamic
model is developed to simulate troughs installed in cold climates and
validated using a parabolic solar trough facility in Winnipeg. The
model is developed in Simulink and will be utilized to simulate a trigeneration
system for heating, cooling and electricity generation in
remote northern communities. The main objective of this simulation
is to obtain operational data of solar troughs in cold climates and use
the model to determine ways to improve the economics and address
cold weather issues.
In this paper the validated Simulink model is applied to simulate a
solar assisted absorption cooling system along with electricity
generation using Organic Rankine Cycle (ORC) and thermal storage.
A control strategy is employed to distribute the heated oil from solar
collectors among the above three systems considering the
temperature requirements. This modelling provides dynamic
performance results using measured meteorological data recorded
every minute at the solar facility location. The purpose of this
modeling approach is to accurately predict system performance at
each time step considering the solar radiation fluctuations due to
passing clouds. Optimization of the controller in cold temperatures is
another goal of the simulation to for example minimize heat losses in
winter when energy demand is high and solar resources are low.
The solar absorption cooling is modeled to use the generated heat
from the solar trough system and provide cooling in summer for a
greenhouse which is located next to the solar field.
The results of the simulation are presented for a summer day in
Winnipeg which includes comparison of performance parameters of
the absorption cooling and ORC systems at different heat transfer
fluid (HTF) temperatures.