Abstract: Biodiesel, as an alternative renewable fuel, has been
receiving increasing attention due to the limited supply of fossil fuels
and the increasing need for energy. Microalgae are promising source
for lipids, which can be converted to biodiesel. The biodiesel
production from microalgae lipids using lipase catalyzed reaction in
supercritical CO2 medium has several advantages over conventional
production processes. However, identifying the optimum microalgae
lipid extraction and transesterification conditions is still a challenge.
In this study, the quality of biodiesel produced from lipids extracted
from Scenedesmus sp. and their enzymatic transesterification using
supercritical carbon dioxide have been investigated. At the optimum
conditions, the highest biodiesel production yield was found to be
82%. The fuel properties of the produced biodiesel, without any
separation step, at optimum reaction condition, were determined and
compared to ASTM standards. The properties were found to comply
with the limits, and showed a low glycerol content, without any
separation step.
Abstract: This paper represents the results of experimental work to investigate the suitability of a waste material (WM) for soft soil stabilisation. In addition, the effect of particle size distribution (PSD) of the waste material on its performance as a soil stabiliser was investigated. The WM used in this study is produced from the incineration processes in domestic energy power plant and it is available in two different grades of fineness (coarse waste material (CWM) and fine waste material (FWM)). An intermediate plasticity silty clayey soil with medium organic matter content has been used in this study. The suitability of the CWM and FWM to improve the physical and engineering properties of the selected soil was evaluated dependant on the results obtained from the consistency limits, compaction characteristics (optimum moisture content (OMC) and maximum dry density (MDD)); along with the unconfined compressive strength test (UCS). Different percentages of CWM were added to the soft soil (3, 6, 9, 12 and 15%) to produce various admixtures. Then the UCS test was carried out on specimens under different curing periods (zero, 7, 14, and 28 days) to find the optimum percentage of CWM. The optimum and other two percentages (either side of the optimum content) were used for FWM to evaluate the effect of the fineness of the WM on UCS of the stabilised soil. Results indicated that both types of the WM used in this study improved the physical properties of the soft soil where the index of plasticity (IP) was decreased significantly. IP was decreased from 21 to 13.64 and 13.10 with 12% of CWM and 15% of FWM respectively. The results of the unconfined compressive strength test indicated that 12% of CWM was the optimum and this percentage developed the UCS value from 202kPa to 500kPa for 28 days cured samples, which is equal, approximately 2.5 times the UCS value for untreated soil. Moreover, this percentage provided 1.4 times the value of UCS for stabilized soil-CWA by using FWM which recorded just under 700kPa after 28 days curing.
Abstract: We report herein the development and preliminary mechanical characterization of fully-dense multi-wall carbon nanotube (MWCNT)-reinforced ceramics and glasses based on a completely new methodology termed High Shear Compaction (HSC). The tubes are introduced and bound to the matrix grains by aid of polymeric binders to form flexible green bodies which are sintered and densified by spark plasma sintering to unprecedentedly high densities of 100% of the pure-matrix value. The strategy was validated across a PyrexTM glass / MWCNT composite while no identifiable factors limit application to other types of matrices. Nondestructive evaluation, based on ultrasonics, of the dynamic mechanical properties of the materials including elastic, shear and bulk modulus as well as Poisson’s ratio showed optimum property improvement at 0.5 %wt tube loading while evidence of nanoscalespecific energy dissipative characteristics acting complementary to nanotube bridging and pull-out indicate a high potential in a wide range of reinforcing and multifunctional applications.
Abstract: Experimental investigations of the DC electric field effect on thermal decomposition of biomass, formation of the axial flow of volatiles (CO, H2, CxHy), mixing of volatiles with swirling airflow at low swirl intensity (S ≈ 0.2-0.35), their ignition and on formation of combustion dynamics are carried out with the aim to understand the mechanism of electric field influence on biomass gasification, combustion of volatiles and heat energy production. The DC electric field effect on combustion dynamics was studied by varying the positive bias voltage of the central electrode from 0.6 kV to 3 kV, whereas the ion current was limited to 2 mA. The results of experimental investigations confirm the field-enhanced biomass gasification with enhanced release of volatiles and the development of endothermic processes at the primary stage of thermochemical conversion of biomass determining the field-enhanced heat energy consumption with the correlating decrease of the flame temperature and heat energy production at this stage of flame formation. Further, the field-enhanced radial expansion of the flame reaction zone correlates with a more complete combustion of volatiles increasing the combustion efficiency by 3% and decreasing the mass fraction of CO, H2 and CxHy in the products, whereas by 10% increases the average volume fraction of CO2 and the heat energy production downstream the combustor increases by 5-10%
Abstract: This paper focuses on a critical component of the
situational awareness (SA), the control of autonomous vertical flight
for vectored thrust aerial vehicle (VTAV). With the SA strategy, we
proposed a neural network motion control procedure to address the
dynamics variation and performance requirement difference of flight
trajectory for a VTAV. This control strategy with using of NARMAL2
neurocontroller for chosen model of VTAV has been verified by
simulation of take-off and forward maneuvers using software
package Simulink and demonstrated good performance for fast
stabilization of motors, consequently, fast SA with economy in
energy can be asserted during search-and-rescue operations.
Abstract: A sensory network consists of multiple detection
locations called sensor nodes, each of which is tiny, featherweight
and portable. A single path routing protocols in wireless sensor
network can lead to holes in the network, since only the nodes
present in the single path is used for the data transmission. Apart
from the advantages like reduced computation, complexity and
resource utilization, there are some drawbacks like throughput,
increased traffic load and delay in data delivery. Therefore, multipath
routing protocols are preferred for WSN. Distributing the traffic
among multiple paths increases the network lifetime. We propose a
scheme, for the data to be transmitted through a dominant path to
save energy. In order to obtain a high delivery ratio, a basic route
reconstruction protocol is utilized to reconstruct the path whenever a
failure is detected. A basic reconstruction routing (BRR) algorithm is
proposed, in which a node can leap over path failure by using the
already existing routing information from its neighbourhood while
the composed data is transmitted from the source to the sink. In order
to save the energy and attain high data delivery ratio, data is
transmitted along a multiple path, which is achieved by BRR
algorithm whenever a failure is detected. Further, the analysis of
how the proposed protocol overcomes the drawback of the existing
protocols is presented. The performance of our protocol is compared
to AOMDV and energy efficient node-disjoint multipath routing
protocol (EENDMRP). The system is implemented using NS-2.34.
The simulation results show that the proposed protocol has high
delivery ratio with low energy consumption.
Abstract: Nowadays, the use of renewable energy sources has been increasingly great because of the cost increase and public demand for clean energy sources. One of the fastest growing sources is wind energy. In this paper, Wind Diesel Hybrid System (WDHS) comprising a Diesel Generator (DG), a Wind Turbine Generator (WTG), the Consumer Load, a Battery-based Energy Storage System (BESS), and a Dump Load (DL) is used. Voltage is controlled by Diesel Generator; the frequency is controlled by BESS and DL. The BESS elimination is an efficient way to reduce maintenance cost and increase the dynamic response. Simulation results with graphs for the frequency of Power System, active power, and the battery power are presented for load changes. The controlling parameters are optimized by using Imperialist Competitive Algorithm (ICA). The simulation results for the BESS/no BESS cases are compared. Results show that in no BESS case, the frequency control is more optimal than the BESS case by using ICA.
Abstract: This study was conducted to determine that carrot powder obtain by different drying methods (oven and vacuum-freeze dryer) of carrot unfit for human consumption that whether feed additives in animal nutrition or not. Carrots randomly divided 2 groups. First group was dried by using oven, second group was by using vacuum freeze dryer methods. Dried carrot prepared from fresh carrot was analysed nutrient matter (energy, crude protein, crude oil, crude ash, beta carotene, mineral concentration and colour). The differences between groups in terms of energy, crude protein, ash, Ca and Mg was not significant (P>0,05). Crude oil, P, beta carotene content and colour values (L, a, b) with vacuum-freeze dryer group was greater than oven group (P
Abstract: This study addresses a concept of the Sustainable Building Environmental Model (SBEM) developed to optimize energy consumption in air conditioning and ventilation (ACV) systems without any deterioration of indoor environmental quality (IEQ). The SBEM incorporates two main components: an adaptive comfort temperature control module (ACT) and a new carbon dioxide demand control module (nDCV). These two modules take an innovative approach to maintain satisfaction of the Indoor Environmental Quality (IEQ) with optimum energy consumption; they provide a rational basis of effective control. A total of 2133 sets of measurement data of indoor air temperature (Ta), relative humidity (Rh) and carbon dioxide concentration (CO2) were conducted in some Hong Kong offices to investigate the potential of integrating the SBEM. A simulation was used to evaluate the dynamic performance of the energy and air conditioning system with the integration of the SBEM in an air-conditioned building. It allows us make a clear picture of the control strategies and performed any pre-tuned of controllers before utilized in real systems. With the integration of SBEM, it was able to save up to 12.3% in simulation of overall electricity consumption, and maintain the average carbon dioxide concentration within 1000ppm and occupant dissatisfaction in 20%.
Abstract: To explore how the brain may recognise objects in its
general,accurate and energy-efficient manner, this paper proposes the
use of a neuromorphic hardware system formed from a Dynamic
Video Sensor (DVS) silicon retina in concert with the SpiNNaker
real-time Spiking Neural Network (SNN) simulator. As a first step
in the exploration on this platform a recognition system for dynamic
hand postures is developed, enabling the study of the methods used
in the visual pathways of the brain. Inspired by the behaviours of
the primary visual cortex, Convolutional Neural Networks (CNNs)
are modelled using both linear perceptrons and spiking Leaky
Integrate-and-Fire (LIF) neurons.
In this study’s largest configuration using these approaches, a
network of 74,210 neurons and 15,216,512 synapses is created and
operated in real-time using 290 SpiNNaker processor cores in parallel
and with 93.0% accuracy. A smaller network using only 1/10th of the
resources is also created, again operating in real-time, and it is able
to recognise the postures with an accuracy of around 86.4% - only
6.6% lower than the much larger system. The recognition rate of the
smaller network developed on this neuromorphic system is sufficient
for a successful hand posture recognition system, and demonstrates
a much improved cost to performance trade-off in its approach.
Abstract: Hybrid electric vehicles can reduce pollution and
improve fuel economy. Power-split hybrid electric vehicles (HEVs)
provide two power paths between the internal combustion engine
(ICE) and energy storage system (ESS) through the gears of an
electrically variable transmission (EVT). EVT allows ICE to operate
independently from vehicle speed all the time. Therefore, the ICE can
operate in the efficient region of its characteristic brake specific fuel
consumption (BSFC) map. The two-mode powertrain can operate in
input-split or compound-split EVT modes and in four different fixed
gear configurations. Power-split architecture is advantageous because
it combines conventional series and parallel power paths. This
research focuses on input-split and compound-split modes in the
two-mode power-split powertrain. Fuzzy Logic Control (FLC) for an
internal combustion engine (ICE) and PI control for electric machines
(EMs) are derived for the urban driving cycle simulation. These
control algorithms reduce vehicle fuel consumption and improve ICE
efficiency while maintaining the state of charge (SOC) of the energy
storage system in an efficient range.
Abstract: Biomass briquette gasification is regarded as a
promising route for efficient briquette use in energy generation, fuels
and other useful chemicals. However, previous research has been
focused on briquette gasification in fixed bed gasifiers such as
updraft and downdraft gasifiers. Fluidised bed gasifier has the
potential to be effectively sized to medium or large scale. This study
investigated the use of fuel briquettes produced from blends of rice
husks and corn cobs biomass, in a bubbling fluidised bed gasifier.
The study adopted a combination of numerical equations and Aspen
Plus simulation software, to predict the product gas (syngas)
composition base on briquette density and biomass composition
(blend ratio of rice husks to corn cobs). The Aspen Plus model was
based on an experimentally validated model from the literature. The
results based on a briquette size 32 mm diameter and relaxed density
range of 500 to 650kg/m3, indicated that fluidisation air required in
the gasifier increased with increase in briquette density, and the
fluidisation air showed to be the controlling factor compared with the
actual air required for gasification of the biomass briquettes. The
mass flowrate of CO2 in the predicted syngas composition increased
with an increase in air flow, in the gasifier, while CO decreased and
H2 was almost constant. The ratio of H2 to CO for various blends of
rice husks and corn cobs did not significantly change at the designed
process air, but a significant difference of 1.0 was observed between
10/90 and 90/10 % blend of rice husks and corn cobs.
Abstract: Whey is the lactose rich by-product of the dairy
industry, having good amount of nutrient reservoir. Most abundant
nutrients are lactose, soluble proteins, lipids and mineral salts.
Disposing of whey by most of milk plants which do not have proper
pre-treatment system is the major issue. As a result of which, there
can be significant loss of potential food and energy source. Thus,
whey has been explored as the substrate for the synthesis of different
value added products such as enzymes. β-galactosidase is one of the
important enzymes and has become the major focus of research due
to its ability to catalyze both hydrolytic as well as
transgalactosylation reaction simultaneously. The enzyme is widely
used in dairy industry as it catalyzes the transformation of lactose to
glucose and galactose, making it suitable for the lactose intolerant
people. The enzyme is intracellular in both bacteria and yeast,
whereas for molds, it has an extracellular location. The present work
was carried to utilize the whey for the production of β-galactosidase
enzyme using both yeast and fungal cultures. The yeast isolate
Kluyveromyces marxianus WIG2 and various fungal strains have
been used in the present study. Different disruption techniques have
also been investigated for the extraction of the enzyme produced
intracellularly from yeast cells. Among the different methods tested
for the disruption of yeast cells, SDS-chloroform showed the
maximum β-galactosidase activity. In case of the tested fungal
cultures, Aureobasidium pullulans NCIM 1050 was observed to be
the maximum extracellular enzyme producer.
Abstract: This study examines the feasibility of indirect solar
desalination in oil producing countries in the Middle East and North
Africa (MENA) region. It relies on value engineering (VE) and costbenefit
with sensitivity analyses to identify optimal coupling
configurations of desalination and solar energy technologies. A
comparative return on investment was assessed as a function of water
costs for varied plant capacities (25,000 to 75,000 m3/day), project
lifetimes (15 to 25 years), and discount rates (5 to 15%) taking into
consideration water and energy subsidies, land cost as well as
environmental externalities in the form of carbon credit related to
greenhouse gas (GHG) emissions reduction. The results showed
reverse osmosis (RO) coupled with photovoltaic technologies (PVs)
as the most promising configuration, robust across different prices for
Brent oil, discount rates, as well as different project lifetimes.
Environmental externalities and subsidies analysis revealed that a
16% reduction in existing subsidy on water tariffs would ensure
economic viability. Additionally, while land costs affect investment
attractiveness, the viability of RO coupled with PV remains possible
for a land purchase cost
Abstract: Current research is targeting new molecular
mechanisms that underlie non-alcoholic fatty liver disease (NAFLD)
and associated metabolic disorders like non-alcoholic steatohepatitis
(NASH). Forty New Zealand White rabbits have been used and fed a
high protein (HP) and energy diet based on grains and containing
11.76 MJ/kg. Boron added to 3 experimental groups’ drinking waters
(30 mg boron/L) as boron compounds. Biochemical analysis
including boron levels, and nuclear magnetic resonance (NMR) based
metabolomics evaluation, and mRNA expression of peroxisome
proliferator-activated receptor (PPAR) family was performed. LDLcholesterol
concentrations alone were decreased in all the
experimental groups. Boron levels in serum and feces were increased.
Content of acetate was in about 2x higher for anhydrous borax group,
at least 3x higher for boric acid group. PPARα mRNA expression
was significantly decreased in boric acid group. Anhydrous borax
attenuated mRNA levels of PPARγ, which was further suppressed by
boric acid. Boron supplementation decreased the degenerative
alterations in hepatocytes. Except borax group other boron groups did
not have a pronounced change in tubular epithels of kidney. In
conclusion, high protein and energy diet leads hepatocytes’
degenerative changes which can be prevented by boron
supplementation. Boric acid seems to be more effective in this
situation.
Abstract: Optimal feeding, including optimal micronutrient
intake, becomes one of the ways to overcome the long-term
consequences of undernutrition. Macronutrient and micronutrient
intake were important to a rapid growth and development of young
children. The study objective was to assess macro and micronutrient
intake and its adequacy in children aged 12-23 months. This survey
was a cross-sectional study, involving 83 caregivers with children
aged 12-23 months old in Senen Sub-district, Central Jakarta selected
through simple random sampling. Data on nutrient intake was
obtained through interview using single 24-hour recall. Repeated 24-
hour recall to sub-sample was done to estimate the proportion of
nutrient inadequacy. The highest prevalence of nutrient inadequacy
was iron (52.4%), followed by vitamin C (30.9%) and zinc (28.8%).
Almost 12% children had inadequate energy intake. More than half
of children (62.6%) were anemic (25.3% were severely anemic).
Micronutrient inadequacy, especially iron, was more problematic
than macronutrient inadequacy in the study area.
Abstract: Computational fluid dynamics analysis of the burning
of syngas fuels derived from biomass and plastic solid waste mixture
through gasification process is presented in this paper. The syngas
fuel is burned in gas turbine can combustor. Gas turbine can
combustor with swirl is designed to burn the fuel efficiently and
reduce the emissions. The main objective is to test the impact of the
alternative syngas fuel compositions and lower heating value on the
combustion performance and emissions. The syngas fuel is produced
by blending palm kernel shell (PKS) with polyethylene (PE) waste
via catalytic steam gasification (fluidized bed reactor). High
hydrogen content syngas fuel was obtained by mixing 30% PE waste
with PKS. The syngas composition obtained through the gasification
process is 76.2% H2, 8.53% CO, 4.39% CO2 and 10.90% CH4. The
lower heating value of the syngas fuel is LHV = 15.98 MJ/m3. Three
fuels were tested in this study natural gas (100%CH4), syngas fuel
and pure hydrogen (100% H2). The power from the combustor was
kept constant for all the fuels tested in this study. The effect of syngas
fuel composition and lower heating value on the flame shape, gas
temperature, mass of carbon dioxide (CO2) and nitrogen oxides
(NOX) per unit of energy generation is presented in this paper. The
results show an increase of the peak flame temperature and NO mass
fractions for the syngas and hydrogen fuels compared to natural gas
fuel combustion. Lower average CO2 emissions at the exit of the
combustor are obtained for the syngas compared to the natural gas
fuel.
Abstract: New design of three dimensional (3D) flywheel system
based on gimbal and gyro mechanics is proposed. The 3D flywheel
device utilizes the rotational motion of three spherical shells and the
conservation of angular momentum to achieve planar locomotion.
Actuators mounted to the ring-shape frames are installed within the
system to drive the spherical shells to rotate, for the purpose of steering
and stabilization. Similar to the design of 2D flywheel system, it is
expected that the spherical shells may function like a “flyball” to store
and supply mechanical energy; additionally, in comparison with
typical single-wheel and spherical robots, the 3D flywheel can be used
for developing omnidirectional robotic systems with better mobility.
The Lagrangian method is applied to derive the equation of motion of
the 3D flywheel system, and simulation studies are presented to verify
the proposed design.
Abstract: This paper presents a novel algorithm for secure,
reliable and flexible transmission of big data in two hop wireless
networks using cooperative jamming scheme. Two hop wireless
networks consist of source, relay and destination nodes. Big data has
to transmit from source to relay and from relay to destination by
deploying security in physical layer. Cooperative jamming scheme
determines transmission of big data in more secure manner by
protecting it from eavesdroppers and malicious nodes of unknown
location. The novel algorithm that ensures secure and energy balance
transmission of big data, includes selection of data transmitting
region, segmenting the selected region, determining probability ratio
for each node (capture node, non-capture and eavesdropper node) in
every segment, evaluating the probability using binary based
evaluation. If it is secure transmission resume with the two- hop
transmission of big data, otherwise prevent the attackers by
cooperative jamming scheme and transmit the data in two-hop
transmission.
Abstract: This paper addresses the design of hospital Intensive
Care Unit windows for the achievement of visual comfort and energy
savings. The aim was to identify the window size and shading system
configurations that could fulfill daylighting adequacy, avoid glare
and reduce energy consumption. The study focused on addressing the
effect of utilizing different shading systems in association with a
range of Window-to-Wall Ratios (WWR) in different orientations
under the desert clear-sky of Cairo, Egypt.
The results of this study demonstrated that solar penetration is a
critical concern affecting the design of ICU windows in desert
locations, as in Cairo, Egypt. Use of shading systems was found to be
essential in providing acceptable daylight performance and energy
saving. Careful positioning of the ICU window towards a proper
orientation can dramatically improve performance. It was observed
that ICU windows facing the north direction enjoyed the widest range
of successful window configuration possibilities at different WWRs.
ICU windows facing south enjoyed a reasonable number of
configuration options as well. By contrast, the ICU windows facing
the east orientation had a very limited number of options that provide
acceptable performance. These require additional local shading
measures at certain times due to glare incidence. Moreover, use of
horizontal sun breakers and solar screens to protect the ICU windows
proved to be more successful than the other alternatives in a wide
range of Window to Wall Ratios. By contrast, the use of light shelves
and vertical shading devices seemed questionable.