Abstract: Residential buildings consume significant amounts of
energy and produce large amount of emissions and waste. However,
there is a substantial potential for energy savings in this sector which
needs to be evaluated over the life cycle of residential buildings. Life
Cycle Assessment (LCA) methodology has been employed to study
the primary energy uses and associated environmental impacts of
different phases (i.e., product, construction, use, end of life, and
beyond building life) for residential buildings. Four different
alternatives of residential buildings in Vancouver (BC, Canada) with
a 50-year lifespan have been evaluated, including High Rise
Apartment (HRA), Low Rise Apartment (LRA), Single family
Attached House (SAH), and Single family Detached House (SDH).
Life cycle performance of the buildings is evaluated for embodied
energy, embodied environmental impacts, operational energy,
operational environmental impacts, total life-cycle energy, and total
life cycle environmental impacts. Estimation of operational energy
and LCA are performed using DesignBuilder software and Athena
Impact estimator software respectively.
The study results revealed that over the life span of the buildings,
the relationship between the energy use and the environmental
impacts are identical. LRA is found to be the best alternative in terms
of embodied energy use and embodied environmental impacts; while,
HRA showed the best life-cycle performance in terms of minimum
energy use and environmental impacts. Sensitivity analysis has also
been carried out to study the influence of building service lifespan
over 50, 75, and 100 years on the relative significance of embodied
energy and total life cycle energy. The life-cycle energy requirements
for SDH are found to be a significant component among the four
types of residential buildings. The overall disclose that the primary
operations of these buildings accounts for 90% of the total life cycle
energy which far outweighs minor differences in embodied effects
between the buildings.
Abstract: This paper proposes a linear model for optimizing
domestic energy consumption in Romania. The particularity of the
model is that it is putting in competition both tangible technologies
and thermal insulation projects with different financing modes.
The model is optimizing the energy system by minimizing the
global discounted cost in household sector, by integrating residential
lighting, space heating, hot water, combined space heating – hot
water, as well as space cooling, in a monolithic model. Another
demand sector included is the passenger transport.
This paper focuses on space heating part, analyzing technical and
economic issues related to investment decisions to envelope and
insulate buildings, in order to minimize energy consumption.
Abstract: This study aims to evaluate the effective size, section
and structural characteristics of circular hollow steel (CHS) damper.
CHS damper is among steel dampers which are used widely for
seismic energy dissipation because they are easy to install, maintain
and are inexpensive. CHS damper dissipates seismic energy through
metallic deformation due to the geometrical elasticity of circular shape
and fatigue resistance around connection part. After calculating the
effective size, which is found to be height to diameter ratio of √3,
nonlinear FE analyses were carried out to evaluate the structural
characteristics and effective section (diameter-to-ratio).
Abstract: Si ion implantation was widely used to synthesize
specimens of SiO2 containing supersaturated Si and subsequent high
temperature annealing induces the formation of embedded
luminescent Si nanocrystals. In this work, the potentialities of excimer
UV-light (172 nm, 7.2 eV) irradiation and rapid thermal annealing
(RTA) to enhance the photoluminescence and to achieve low
temperature formation of Si nanocrystals have been investigated. The
Si ions were introduced at acceleration energy of 180 keV to fluence of
7.5 x 1016 ions/cm2. The implanted samples were subsequently
irradiated with an excimer-UV lamp. After the process, the samples
were rapidly thermal annealed before furnace annealing (FA).
Photoluminescence spectra were measured at various stages at the
process. We found that the luminescence intensity is strongly
enhanced with excimer-UV irradiation and RTA. Moreover, effective
visible photoluminescence is found to be observed even after FA at
900 oC, only for specimens treated with excimer-UV lamp and RTA.
We also prepared specimens of Si nanocrystals embedded in a SiO2 by
reactive pulsed laser deposition (PLD) in an oxygen atmosphere. We
will make clear the similarities and differences with the way of
preparation.
Abstract: An Acoustic Micro-Energy Harvester (AMEH) is
developed to convert wasted acoustical energy into useful electrical
energy. AMEH is mathematically modeled using Lumped Element
Modelling (LEM) and Euler-Bernoulli beam (EBB) modelling. An
experiment is designed to validate the mathematical model and assess
the feasibility of AMEH. Comparison of theoretical and experimental
data on critical parameter value such as Mm, Cms, dm and Ceb showed
the variances are within 1% to 6%, which is reasonably acceptable.
Then, AMEH undergoes bandwidth tuning for performance
optimization. The AMEH successfully produces 0.9V/(m/s^2) and
1.79μW/(m^2/s^4) at 60Hz and 400kΩ resistive load which only
show variances about 7% compared to theoretical data. At 1g and
60Hz resonance frequency, the averaged power output is about
2.2mW which fulfilled a range of wireless sensors and
communication peripherals power requirements. Finally, the design
for AMEH is assessed, validated and deemed as a feasible design.
Abstract: Elastomeric polymer foam has been used widely in
the automotive industry, especially for isolating unwanted vibrations.
Such material is able to absorb unwanted vibration due to its
combination of elastic and viscous properties. However, the ‘creep
effect’, poor stress distribution and susceptibility to high
temperatures are the main disadvantages of such a system.
In this study, improvements in the performance of elastomeric
foam as a vibration isolator were investigated using the concept of
Foam Filled Fluid (FFFluid). In FFFluid devices, the foam takes the
form of capsule shapes, and is mixed with viscous fluid, while the
mixture is contained in a closed vessel. When the FFFluid isolator is
affected by vibrations, energy is absorbed, due to the elastic strain of
the foam. As the foam is compressed, there is also movement of the
fluid, which contributes to further energy absorption as the fluid
shears. Also, and dependent on the design adopted, the packaging
could also attenuate vibration through energy absorption via friction
and/or elastic strain.
The present study focuses on the advantages of the FFFluid
concept over the dry polymeric foam in the role of vibration isolation.
This comparative study between the performance of dry foam and the
FFFluid was made according to experimental procedures. The paper
concludes by evaluating the performance of the FFFluid isolator in
the suspension system of a light vehicle. One outcome of this
research is that the FFFluid may preferable over elastomer isolators
in certain applications, as it enables a reduction in the effects of high
temperatures and of ‘creep effects’, thereby increasing the reliability
and load distribution. The stiffness coefficient of the system has
increased about 60% by using an FFFluid sample. The technology
represented by the FFFluid is therefore considered by this research
suitable for application in the suspension system of a light vehicle.
Abstract: This work consists of a numerical simulation of
convective heat transfer in a vertical plane channel filled with a heat
generating porous medium, in the absence of local thermal
equilibrium. The walls are maintained to a constant temperature and
the inlet velocity is uniform. The dynamic range is described by the
Darcy-Brinkman model and the thermal field by two energy
equations model. A dimensionless formulation is developed for
performing a parametric study based on certain dimensionless groups
such as, the Biot interstitial number, the thermal conductivity ratio
and the volumetric heat generation, q '''. The governing equations are
solved using the finite volume method, gave rise to a multitude of
results concerning in particular the thermal field in the porous
channel and the existence or not of the local thermal equilibrium.
Abstract: The elastic properties and fracture of two-dimensional
graphene were calculated purely from the atomic bonding (stretching
and bending) based on molecular mechanics method. Considering the
representative unit cell of graphene under various loading conditions,
the deformations of carbon bonds and the variations of the interlayer
distance could be realized numerically under the geometry constraints
and minimum energy assumption. In elastic region, it was found that
graphene was in-plane isotropic. Meanwhile, the in-plane deformation
of the representative unit cell is not uniform along armchair direction
due to the discrete and non-uniform distributions of the atoms. The
fracture of graphene could be predicted using fracture criteria based on
the critical bond length, over which the bond would break. It was
noticed that the fracture behavior were directional dependent, which
was consistent with molecular dynamics simulation results.
Abstract: Amoxicillin is an antibiotic which is widely used to
treat various infections in both human beings and animals. However,
when amoxicillin is released into the environment, it is a major
problem. Amoxicillin causes bacterial resistance to these drugs and
failure of treatment with antibiotics. Liquid membrane is of great
interest as a promising method for the separation and recovery of the
target ions from aqueous solutions due to the use of carriers for the
transport mechanism, resulting in highly selectivity and rapid
transportation of the desired metal ions. The simultaneous processes
of extraction and stripping in a single unit operation of liquid
membrane system are very interesting. Therefore, it is practical to
apply liquid membrane, particularly the HFSLM for industrial
applications as HFSLM is proved to be a separation process with
lower capital and operating costs, low energy and extractant with
long life time, high selectivity and high fluxes compared with solid
membranes. It is a simple design amenable to scaling up for industrial
applications. The extraction and recovery for (Amoxicillin) through
the hollow fiber supported liquid membrane (HFSLM) using
aliquat336 as a carrier were explored with the experimental data. The
important variables affecting on transport of amoxicillin viz.
extractant concentration and operating time were investigated. The
highest AMOX- extraction percentages of 85.35 and Amoxicillin
stripping of 80.04 were achieved with the best condition at 6 mmol/L
[aliquat336] and operating time 100 min. The extraction reaction
order (n) and the extraction reaction rate constant (kf) were found to
be 1.00 and 0.0344 min-1, respectively.
Abstract: In this work new macroporous Ni electrodes modified
with Au nanoparticles for hydrogen production have been developed.
The supporting macroporous Ni electrodes have been obtained by
means of the electrodeposition at high current densities. Then, the Au
nanoparticles were synthesized and added to the electrode surface.
The electrocatalytic behaviour of the developed electrocatalysts was
studied by means of pseudo-steady-state polarization curves,
electrochemical impedance spectroscopy (EIS) and hydrogen
discharge curves. The size of the Au synthetized nanoparticles shows
a monomodal distribution, with a very sharp band between 10 and 50
nm. The characteristic parameters d10, d50 and d90 were 14, 20 and
31 nm respectively. From Tafel polarization data has been concluded
that the Au nanoparticles improve the catalytic activity of the
developed electrodes towards the HER respect to the macroporous Ni
electrodes. EIS permits to obtain the electrochemically active area by
means of the roughness factor value. All the developed electrodes
show roughness factor values in the same order of magnitude. From
the activation energy results it can be concluded that the Au
nanoparticles improve the intrinsic catalytic activity of the
macroporous Ni electrodes.
Abstract: In this paper, the energy saving and human thermal
comfort in a typical office room are investigated. The impact of a
combined system of exhaust inlet air with light slots located at the
ceiling level in a room served by displacement ventilation system is
numerically modelled. Previous experimental data are used to
validate the Computational Fluid Dynamic (CFD) model. A case
study of simulated office room includes two seating occupants, two
computers, two data loggers and four lamps. The combined system is
located at the ceiling level above the heat sources. A new method of
calculation for the cooling coil load in Stratified Air Distribution
(STRAD) system is used in this study. The results show that 47.4%
energy saving of space cooling load can be achieved by combing the
exhaust inlet air with light slots at the ceiling level above the heat
sources.
Abstract: The Chair of Thermal Engineering at Poznan
University of Technology has been conducted research works on the
possibilities of using carbon nanostructures in energy and mechanics
applications for a couple of years. Those studies have provided results in a form of co-operation with foreign research centres, numerous publications and patent
applications.
Authors of this paper have studied the influence of multi-walled
carbon nanostructures on changes in static friction arising when steel
surfaces were moved. Tests were made using the original test stand
consisting of automatically controlled inclined plane driven by
precise stepper motors. Computer program created in the LabView
environment was responsible for monitoring of the stand operation,
accuracy of measurements and archiving the obtained results. Such a
solution enabled to obtain high accuracy and repeatability of all
conducted experiments.
Tests and analysis of the obtained results allowed us to determine
how additional layers of carbon nanostructures influenced on changes
of static friction coefficients. At the same time, we analyzed the
potential possibilities of applying nanostructures under consideration
in mechanics.
Abstract: Remote arid areas of the vast expanses of the African
deserts hold huge subterranean reserves of brackish water resources
waiting for economic development. This work presents design
guidelines as well as initial performance data of new autonomous
solar desalination equipment which could help local communities
produce their own fresh water using solar energy only and, why not,
contribute to transforming desert lands into lush gardens. The output
of solar distillation equipments are typically low and in the range of 3
l/m2/day on the average. This new design with an integrated, water
based, environmentally-friendly solar heat storage system produced 5
l/m2/day in early spring weather. Equipment output during summer
exceeded 9 liters per m2 per day.
Abstract: Let us consider that the entire universe is composed of
a single hydrogen atom within which the electron is moving around
the proton. In this case, according to classical theories of physics,
radiation, photons respectively, should be absorbed by the electron.
Depending on the number of photons absorbed, the electron radius of
rotation around the proton is established. Until now, the principle of
photons absorption by electrons and the electron transition to a new
energy level, namely to a higher radius of rotation around the proton,
is not clarified in physics. This paper aims to demonstrate that
radiation, photons respectively, have mass and negative electrostatic
charge similar to electrons but infinitely smaller. The experiments
which demonstrate this theory are simple: thermal expansion,
photoelectric effect and thermonuclear reaction.
Abstract: Mobil Producing Nigeria Unlimited (MPNU), a
subsidiary of ExxonMobil and the highest crude oil & condensate
producer in Nigeria has its operational base and an oil terminal, the
Qua Iboe terminal (QIT) located at Ibeno, Nigeria. Other oil
companies like Network Exploration and Production Nigeria Ltd,
Frontier Oil Ltd; Shell Petroleum Development Company Ltd; Elf
Petroleum Nigeria Ltd and Nigerian Agip Energy, a subsidiary of the
Italian ENI E&P operate onshore, on the continental shelf and in deep
offshore of the Atlantic Ocean, respectively with the coastal waters of
Ibeno, Nigeria as the nearest shoreline. This study was designed to
delineate the oil-polluted sites in Ibeno, Nigeria using
microbiological and physico-chemical characterization of soils,
sediments and ground and surface water samples from the study area.
Results obtained revealed that there have been significant recent
hydrocarbon inputs into this environment as observed from the high
counts of hydrocarbonoclastic microorganisms in excess of 1% at all
the stations sampled. Moreover, high concentrations of THC, BTEX
and heavy metals contents in all the samples analyzed corroborate the
high recent crude oil input into the study area. The results also
showed that the pollution of the different environmental media
sampled were of varying degrees, following the trend: ground water
> surface water > sediments > soils.
Abstract: Evapotranspiration is one of the most important
components of the hydrological cycle. Evapotranspiration (ETo) is an
important variable in water and energy balances on the earth’s
surface, and knowledge of the distribution of ET is a key factor in
hydrology, climatology, agronomy and ecology studies. Many
researchers have a valid relationship, which is a function of climate
factors, to estimate the potential evapotranspiration presented to the
plant water stress or water loss, prevent. The FAO-Penman method
(PM) had been recommended as a standard method. This method
requires many data and these data are not available in every area of
world. So, other methods should be evaluated for these conditions.
When sufficient or reliable data to solve the PM equation are not
available then Hargreaves equation can be used. The Hargreaves
equation (HG) requires only daily mean, maximum and minimum air
temperature extraterrestrial radiation .In this study, Hargreaves
method (HG) were evaluated in 12 stations in the North West region
of Iran. Results of HG and M.HG methods were compared with
results of PM method. Statistical analysis of this comparison showed
that calibration process has had significant effect on efficiency of
Hargreaves method.
Abstract: The use of hydroelectric pump-storage system at large
scale, MW-size systems, is already widespread around the world.
Designed for large scale applications, pump-storage station can be
scaled-down for small, remote residential applications. Given the cost
and complexity associated with installing a substation further than
100 miles from the main transmission lines, a remote, independent
and self-sufficient system is by far the most feasible solution. This
article is aiming at the design of wind and solar power generating
system, by means of pumped-storage to replace the wind and /or solar
power systems with a battery bank energy storage. Wind and solar
pumped-storage power generating system can reduce the cost of
power generation system, according to the user's electricity load and
resource condition and also can ensure system reliability of power
supply. Wind and solar pumped-storage power generation system is
well suited for remote residential applications with intermittent wind
and/or solar energy. This type of power systems, installed in these
locations, could be a very good alternative, with economic benefits
and positive social effects. The advantage of pumped storage power
system, where wind power regulation is calculated, shows that a
significant smoothing of the produced power is obtained, resulting in
a power-on-demand system’s capability, concomitant to extra
economic benefits.
Abstract: The sea waves carry thousands of GWs of power
globally. Although there are a number of different approaches to
harness offshore energy, they are likely to be expensive, practically
challenging, and vulnerable to storms. Therefore, this paper considers
using the near shore waves for generating mechanical and electrical
power. It introduces two new approaches, the wave manipulation and
using a variable duct turbine, for intercepting very wide wave fronts
and coping with the fluctuations of the wave height and the sea level,
respectively. The first approach effectively allows capturing much
more energy yet with a much narrower turbine rotor. The second
approach allows using a rotor with a smaller radius but captures
energy of higher wave fronts at higher sea levels yet preventing it
from totally submerging. To illustrate the effectiveness of the first
approach, the paper contains a description and the simulation results
of a scale model of a wave manipulator. Then, it includes the results
of testing a physical model of the manipulator and a single duct, axial
flow turbine in a wave flume in the laboratory. The paper also
includes comparisons of theoretical predictions, simulation results,
and wave flume tests with respect to the incident energy, loss in wave
manipulation, minimal loss, brake torque, and the angular velocity.
Abstract: This paper presents the performance of Integrated
Bacterial Foraging Optimization and Particle Swarm Optimization
(IBFO_PSO) technique in MANET routing. The BFO is a bio-inspired
algorithm, which simulates the foraging behavior of bacteria.
It is effectively applied in improving the routing performance in
MANET. In results, it is proved that the PSO integrated with BFO
reduces routing delay, energy consumption and communication
overhead.
Abstract: A novel method is presented for obtaining the stress
field induced by an edge dislocation in a multilayered composite. To
demonstrate the applications of the obtained solution, we consider the
problem of an interfacial crack in a periodically layered bimaterial
medium. The crack is modelled as a continuous distribution of edge
dislocations and the Distributed Dislocation Technique (DDT) is
utilized to obtain numerical results for the energy release rate (ERR).
The numerical implementation of the dislocation solution in
MATLAB is also provided.