Abstract: In order to compare the performance of the carbon dioxide and HFC-125 heat pumps for medium-and high-temperature heating, both heat pump cycles were optimized using a simulation method. To fairly compare the performance of the cycles by using different working fluids, each cycle was optimized from the viewpoint of heating COP by two design parameters. The first is the gas cooler exit temperature and the other is the ratio of the overall heat conductance of the gas cooler to the combined overall heat conductance of the gas cooler and the evaporator. The inlet and outlet temperatures of secondary fluid of the gas cooler were fixed at 40/90°C and 40/150°C.The results shows that the HFC-125 heat pump has 6% higher heating COP than carbon dioxide heat pump when the heat sink exit temperature is fixed at 90ºC, while the latter outperforms the former when the heat sink exit temperature is fixed at 150ºC under the simulation conditions considered in the present study.
Abstract: Alternative energy is any energy source that is an alternative to fossil fuel. These alternatives are intended to address concerns about such fossil fuels. Today, because of the variety of energy choices and differing goals of their advocates, defining some energy types as "alternative" is highly controversial. Most of the recent and existing alternative sources of energy are discussed below
Abstract: The paper presents the results of microhardness and
microstructure of low carbon steel surface melted using carbon
dioxide laser with a wavelength of 10.6μm and a maximum output
power of 2000W. The processing parameters such as the laser power,
and the scanning rate were investigated in this study. After surface
melting two distinct regions formed corresponding to the melted zone
MZ, and the heat affected zone HAZ. The laser melted region
displayed a cellular fine structures while the HAZ displayed
martensite or bainite structure. At different processing parameters,
the original microstructure of this steel (Ferrite+Pearlite) has been
transformed to new phases of martensitic and bainitic structures. The
fine structure and the high microhardness are evidence of the high
cooling rates which follow the laser melting. The melting pool and
the transformed microstructure in the laser surface melted region of
carbon steel showed clear dependence on laser power and scanning
rate.
Abstract: Agricultural residue such as oil palm fronds (OPF) is
cheap, widespread and available throughout the year. Hemicelluloses
extracted from OPF can be hydrolyzed to their monomers and used in
production of xylooligosaccharides (XOs). The objective of the
present study was to optimize the enzymatic hydrolysis process of
OPF hemicellulose by varying pH, temperature, enzyme and substrate
concentration for production of XOs. Hemicelluloses was extracted
from OPF by using 3 M potassium hydroxide (KOH) at temperature of
40°C for 4 hrs and stirred at 400 rpm. The hemicellulose was then
hydrolyzed using Trichoderma longibrachiatum xylanase at different
pH, temperature, enzyme and substrate concentration. XOs were
characterized based on reducing sugar determination. The optimum
conditions to produced XOs from OPF hemicellulose was obtained at
pH 4.6, temperature of 40°C , enzyme concentration of 2 U/mL and
2% substrate concentration. The results established the suitability of
oil palm fronds as raw material for production of XOs.
Abstract: The photochemical and photo-Fenton oxidation of 1,3-dichloro-2-propanol was performed in a batch reactor, at room temperature, using UV radiation, H2O2 as oxidant, and Fenton-s reagent. The effect of the oxidative agent-s initial concentration was investigated as well as the effect of the initial concentration of Fe(II) by following the target compound degradation, the total organic carbon removal and the chloride ion production. Also, from the kinetic analysis conducted and proposed reaction scheme it was deduced that the addition of Fe(II) significantly increases the production and the further oxidation of the chlorinated intermediates.
Abstract: In this study, Li4SiO4 powder was successfully
synthesized via sol gel method followed by drying at 150oC. Lithium
oxide, Li2O and silicon oxide, SiO2 were used as the starting
materials with citric acid as the chelating agent. The obtained powder
was then sintered at various temperatures. Crystallographic phase
analysis, morphology and ionic conductivity were investigated
systematically employing X-ray diffraction, Fourier Transform
Infrared, Scanning Electron Microscopy and AC impedance
spectroscopy. XRD result showed the formation of pure monoclinic
Li4SiO4 crystal structure with lattice parameters a = 5.140 Å, b =
6.094 Å, c = 5.293 Å, β = 90o in the sample sintered at 750oC. This
observation was confirmed by FTIR analysis. The bulk conductivity
of this sample at room temperature was 3.35 × 10-6 S cm-1 and the
highest bulk conductivity of 1.16 × 10-4 S cm-1 was obtained at
100°C. The results indicated that, the Li4SiO4 compound has
potential to be used as host for LISICON structured solid electrolyte
for low temperature application.
Abstract: This was the first document revealing the
investigation of protein hydrolysate production optimization from J.
curcas cake. Proximate analysis of raw material showed 18.98%
protein, 5.31% ash, 8.52% moisture and 12.18% lipid. The
appropriate protein hydrolysate production process began with
grinding the J. curcas cake into small pieces. Then it was suspended
in 2.5% sodium hydroxide solution with ratio between solution/ J.
curcas cake at 80:1 (v/w). The hydrolysis reaction was controlled at
temperature 50 °C in water bath for 45 minutes. After that, the
supernatant (protein hydrolysate) was separated using centrifuge at
8000g for 30 minutes. The maximum yield of resulting protein
hydrolysate was 73.27 % with 7.34% moisture, 71.69% total protein,
7.12% lipid, 2.49% ash. The product was also capable of well
dissolving in water.
Abstract: In the present study Schwertmannite (an iron oxide
hydroxide) is selected as an adsorbent for defluoridation of water.
The adsorbent was prepared by wet chemical process and was
characterized by SEM, XRD and BET. The fluoride adsorption
efficiency of the prepared adsorbent was determined with respect to
contact time, initial fluoride concentration, adsorbent dose and pH of
the solution. The batch adsorption data revealed that the fluoride
adsorption efficiency was highly influenced by the studied factors.
Equilibrium was attained within one hour of contact time indicating
fast kinetics and the adsorption data followed pseudo second order
kinetic model. Equilibrium isotherm data fitted to both Langmuir and
Freundlich isotherm models for a concentration range of 5-30 mg/L.
The adsorption system followed Langmuir isotherm model with
maximum adsorption capacity of 11.3 mg/g. The high adsorption
capacity of Schwertmannite points towards the potential of this
adsorbent for fluoride removal from aqueous medium.
Abstract: This paper reports the results of an experimental work
conducted to investigate the effect of curing conditions on the
compressive strength of self-compacting geopolymer concrete
prepared by using fly ash as base material and combination of sodium
hydroxide and sodium silicate as alkaline activator. The experiments
were conducted by varying the curing time and curing temperature in
the range of 24-96 hours and 60-90°C respectively. The essential
workability properties of freshly prepared Self-compacting
Geopolymer concrete such as filling ability, passing ability and
segregation resistance were evaluated by using Slump flow,
V-funnel, L-box and J-ring test methods. The fundamental
requirements of high flowability and resistance to segregation as
specified by guidelines on Self-compacting Concrete by EFNARC
were satisfied. Test results indicate that longer curing time and curing
the concrete specimens at higher temperatures result in higher
compressive strength. There was increase in compressive strength
with the increase in curing time; however increase in compressive
strength after 48 hours was not significant. Concrete specimens cured
at 70°C produced the highest compressive strength as compared to
specimens cured at 60°C, 80°C and 90°C.
Abstract: There is growing interest in biodiesel (fatty acid
methyl ester or FAME) because of the similarity in its properties
when compared to those of diesel fuels. Diesel engines operated on
biodiesel have lower emissions of carbon monoxide, unburned
hydrocarbons, particulate matter, and air toxics than when operated
on petroleum-based diesel fuel. Production of fatty acid methyl ester
(FAME) from rapeseed (nonedible oil) fatty acid distillate having
high free fatty acids (FFA) was investigated in this work. Conditions
for esterification process of rapeseed oil were 1.8 % H2SO4 as
catalyst, MeOH/oil of molar ratio 2 : 0.1 and reaction temperature
65 °C, for a period of 3h. The yield of methyl ester was > 90 % in 1
h.
The amount of FFA was reduced from 93 wt % to less than 2 wt %
at the end of the esterification process. The FAME was pureed by
neutralization with 1 M sodium hydroxide in water solution at a
reaction temperature of 62 °C. The final FAME product met with the
biodiesel quality standard, and ASTM D 6751.
Abstract: We succeeded to produce a high performance and flexible graphene/Manganese dioxide (G/MnO2) electrode coated on flexible polyethylene terephthalate (PET) substrate. The graphene film is initially synthesized by drop-casting the graphene oxide (GO) solution on the PET substrate, followed by simultaneous reduction and patterning of the dried film using carbon dioxide (CO2) laser beam with power of 1.8 W. Potentiostatic Anodic Deposition method was used to deposit thin film of MnO2 with different loading mass 10 – 50 and 100 μg.cm-2 on the pre-prepared graphene film. The electrodes were fully characterized in terms of structure, morphology, and electrochemical performance. A maximum specific capacitance of 973 F.g-1 was attributed when depositing 50μg.cm-2 MnO2 on the laser reduced graphene oxide rGO (or G/50MnO2) and over 92% of its initial capacitance was retained after 1000 cycles. The good electrochemical performance and long-term cycling stability make our proposed approach a promising candidate in the supercapacitor applications.
Abstract: This paper reports the influence of sucrose on the
preservation of CO2 hydrate crystal samples. The particle diameter of
hydrate samples were 1.0 and 5.6-8.0 mm. Mass fraction of sucrose in
the sample was 0.16. The samples were stored at the aerated condition
under atmospheric pressure and at the temperature of 253 or 258 K.
The results indicated that the mass fractions of CO2 hydrate in the
samples with sucrose were 0.10 ± 0.03 at the end of 3-week
preservation, regardless of temperature and particle diameter. Mass
fraction of CO2 hydrate in the samples with sucrose was higher than
that of pure CO2 hydrate for 1.0 mm particle diameter, while was
lower than that of pure CO2 hydrate for 5.6-8.0 mm particle diameter.
Discussion is made on the influence of sucrose on the dissociation of
CO2 hydrate and the resulting formation of ice.
Abstract: Electrochemical-oxidation of Reactive Black-5 (RB- 5) was conducted for degradation using DSA type Ti/RuO2-SnO2- Sb2O5 electrode. In the study, for electro-oxidation, electrode was indigenously fabricated in laboratory using titanium as substrate. This substrate was coated using different metal oxides RuO2, Sb2O5 and SnO2 by thermal decomposition method. Laboratory scale batch reactor was used for degradation and decolorization studies at pH 2, 7 and 11. Current density (50mA/cm2) and distance between electrodes (8mm) were kept constant for all experiments. Under identical conditions, removal of color, COD and TOC at initial pH 2 was 99.40%, 55% and 37% respectively for initial concentration of 100 mg/L RB-5. Surface morphology and composition of the fabricated electrode coatings were characterized using scanning electron microscopy (SEM) and energy dispersive X-ray spectroscopy (EDX) respectively. Coating microstructure was analyzed by X-ray diffraction (XRD). Results of this study further revealed that almost 90% of oxidation occurred within 5-10 minutes.
Abstract: Solid oxide fuel cells have been considered in the last years as one of the most promising technologies for very highefficiency electric energy generation from hydrogen or other hydrocarbons, both with simple fuel cell plants and with integrated gas turbine-fuel cell systems. In the present study, a detailed thermodynamic analysis has been carried out. Mass and exergy balances are performed not only for the whole plant but also for each component in order to evaluate the thermal efficiency of combined cycle. Moreover, different sources of irreversibilities within the SOFC stack have been discussed and a parametric study conducted to evaluate the effect of temperature as well as pressure on SOFC irreversibilities and its performance. In this investigation methane and hydrogen have been used for fueling the SOFC stack and combustion chamber.
Abstract: Carbon dioxide capture process has been simulated
and studied under different process conditions. It has been shown
that several process parameters such as lean amine temperature,
number of adsorber stages, number of stripper stages and stripper
pressure affect different process conditions and outputs such as
carbon dioxide removal and reboiler duty. It may be concluded that
the simulation of carbon dioxide capture process can help to estimate
the best process conditions.
Abstract: The performance of modified Fenton (MF) treatment
to promote PAH oxidation in artificially contaminated soil was
investigated in packed soil column with a hydrogen peroxide (H2O2)
delivery system simulating in situ injection. Soil samples were spiked
with phenanthrene (low molecular weight PAH) and fluoranthene
(high molecular weight PAH) to an initial concentration of 500
mg/kg dried soil each. The effectiveness of process parameters
H2O2/soil, iron/soil, chelating agent/soil weight ratios and reaction
time were studied using a 24 three level factorial design experiments.
Statistically significant quadratic models were developed using
Response Surface Methodology (RSM) for degrading PAHs from the
soil samples. Optimum operating condition was achieved at mild
range of H2O2/soil, iron/soil and chelating agent/soil weight ratios,
indicating cost efficient method for treating highly contaminated
lands.
Abstract: The Ni/α-Al2O3 catalysts with different amounts of La
as promoter from 0 to 4 wt % were prepared, characterized and their
catalytic activity was investigated in syngas methanation reaction.
Effects of reaction temperature and lanthanum loading on carbon
oxides conversion and methane selectivity were also studied. Adding
certain amount of lanthanum to 10Ni /α-Al2O3 catalysts can decrease
the average NiO crystallite diameter which leads to higher activity and
stability while excessive addition would cause deactivation quickly.
Stability on stream towards deactivation was observed up to 800 min
at 500 °C, 0.1MPa and 600000 mL·g-1·h-1.
Abstract: A study concerning the photocatalytic decolourization
of Congo red (CR) dye, over artificial UV irradiation is presented.
Photocatalysts based on a commercial titanium dioxide (TiO2)
modified with transition metals (Ni, Cu and Zn) were used. The
dopage method used was wet impregnation. A TiO2 sample without
salt was subjected to the same hydrothermal treatment to be used as
reference. Congo red solutions to several pH conditions (natural and
basic) were used to evaluate photocatalytic performance of each
doped catalysts. Photodecolourization percentage was measured
spectrofotrometically after 3 h of treatment to 499 nm as response
variable. Kinetics investigations of photodegradation indicated that
reactions obey to Langmuir-Hinshelwood model and pseudo–first
order law. The rate constant studies of photocatalytic decolourization
reactions for Zn–TiO2 and Cu–TiO2 photocatalysts indicated that in
all cases the rate constant of the reaction was higher than that of TiO2
undoped. These results show that nature of the metal modifying the
TiO2 influence on the efficiency of the photocatalyst evaluated in
process. Ni does not present an additional effect compared with TiO2,
while Zn enhances the photoactivity due to its electronic properties.
Abstract: Nowadays, the focus on renewable energy and alternative fuels has increased due to increasing oil prices, environment pollution, and also concern on preserving the nature. Biodiesel has been known as an attractive alternative fuel although biodiesel produced from edible oil is very expensive than conventional diesel. Therefore, the uses of biodiesel produced from non-edible oils are much better option. Currently Jatropha biodiesel (JBD) is receiving attention as an alternative fuel for diesel engine. Biodiesel is non-toxic, biodegradable, high lubricant ability, highly renewable, and its use therefore produces real reduction in petroleum consumption and carbon dioxide (CO2) emissions. Although biodiesel has many advantages, but it still has several properties need to improve, such as lower calorific value, lower effective engine power, higher emission of nitrogen oxides (NOX) and greater sensitivity to low temperature. Exhaust gas recirculation (EGR) is effective technique to reduce NOX emission from diesel engines because it enables lower flame temperature and oxygen concentration in the combustion chamber. Some studies succeeded to reduce the NOX emission from biodiesel by EGR but they observed increasing soot emission. The aim of this study was to investigate the engine performance and soot emission by using blended Jatropha biodiesel with different EGR rates. A CI engine that is water-cooled, turbocharged, using indirect injection system was used for the investigation. Soot emission, NOX, CO2, carbon monoxide (CO) were recorded and various engine performance parameters were also evaluated.
Abstract: Cobalt was acid nitric leached from a mixed cobaltcopper
oxide with variable acid concentration. Resulting
experimental data were used to analyze effects of increase in acid
concentration, based on a shrinking core model of the process. The
mathematical simulation demonstrated that the time rate of the
dissolution mechanism is an increasing function of acid
concentration. It was also shown that the magnitude of the acid
concentration effect is time dependent and the increase in acid
concentration is more effective at earlier stage of the dissolution than
at later stage. The remaining process parameters are comprehensively
affected by acid concentration and their interaction is synergetic.