Abstract: We have measured the pressure drop and convective
heat transfer coefficient of water – based AL(25nm),AL2O3(30nm)
and CuO(50nm) Nanofluids flowing through a uniform heated
circular tube in the fully developed laminar flow regime. The
experimental results show that the data for Nanofluids friction factor
show a good agreement with analytical prediction from the Darcy's
equation for single-phase flow. After reducing the experimental
results to the form of Reynolds, Rayleigh and Nusselt numbers. The
results show the local Nusselt number and temperature have
distribution with the non-dimensional axial distance from the tube
entry. Study decided that thenNanofluid as Newtonian fluids through
the design of the linear relationship between shear stress and the rate
of stress has been the study of three chains of the Nanofluid with
different concentrations and where the AL, AL2O3 and CuO – water
ranging from (0.25 - 2.5 vol %). In addition to measuring the four
properties of the Nanofluid in practice so as to ensure the validity of
equations of properties developed by the researchers in this area and
these properties is viscosity, specific heat, and density and found that
the difference does not exceed 3.5% for the experimental equations
between them and the practical. The study also demonstrated that the
amount of the increase in heat transfer coefficient for three types of
Nano fluid is AL, AL2O3, and CuO – Water and these ratios are
respectively (45%, 32%, 25%) with insulation and without insulation
(36%, 23%, 19%), and the statement of any of the cases the best
increase in heat transfer has been proven that using insulation is
better than not using it. I have been using three types of Nano
particles and one metallic Nanoparticle and two oxide Nanoparticle
and a statement, whichever gives the best increase in heat transfer.
Abstract: All around the world pulp and paper industries are the
biggest plant production with the environmental pollution as the
biggest challenge facing the pulp manufacturing operations. The
concern among these industries is to produce a high volume of papers
with the high quality standard and of low cost without affecting the
environment. This result obtained from this bleaching study show
that the activation of peroxide was an effective method of reducing
the total applied charge of chlorine dioxide which is harmful to our
environment and also show that softwood and hardwood Kraft pulps
responded linearly to the peroxide treatments. During the bleaching
process the production plant produce chlorines. Under the trial stages
chloride dioxide has been reduced by 3 kg/ton to reduce the
brightness from 65% ISO to 60% ISO of pulp and the dosing point
returned to the E stage charges by pre-treating Kraft pulps with
hydrogen peroxide. The pulp and paper industry has developed
elemental chlorine free (ECF) and totally chlorine free (TCF)
bleaching, in their quest for being environmental friendly, they have
been looking at ways to turn their ECF process into a TCF process
while still being competitive. This prompted the research to
investigate the capability of the hydrogen peroxide as catalyst to
reduce chloride dioxide.
Abstract: Enzymatic saccharification of biomass for reducing
sugar production is one of the crucial processes in biofuel production
through biochemical conversion. In this study, enzymatic
saccharification of dilute potassium hydroxide (KOH) pre-treated
Tetraselmis suecica biomass was carried out by using cellulase
enzyme obtained from Trichoderma longibrachiatum. Initially, the
pre-treatment conditions were optimised by changing alkali reagent
concentration, retention time for reaction, and temperature. The T.
suecica biomass after pre-treatment was also characterized using
Fourier Transform Infrared Spectra and Scanning Electron
Microscope. These analyses revealed that the functional group such
as acetyl and hydroxyl groups, structure and surface of T. suecica
biomass were changed through pre-treatment, which is favourable for
enzymatic saccharification process. Comparison of enzymatic
saccharification of untreated and pre-treated microalgal biomass
indicated that higher level of reducing sugar can be obtained from
pre-treated T. suecica. Enzymatic saccharification of pre-treated T.
suecica biomass was optimised by changing temperature, pH, and
enzyme concentration to solid ratio ([E]/[S]). Highest conversion of
carbohydrate into reducing sugar of 95% amounted to reducing sugar
yield of 20 (wt%) from pre-treated T. suecica was obtained from
saccharification, at temperature: 40°C, pH: 4.5 and [E]/[S] of 0.1
after 72 h of incubation. Hydrolysate obtained from enzymatic
saccharification of pretreated T. suecica biomass was further
fermented into biobutanol using Clostridium saccharoperbutyliticum
as biocatalyst. The results from this study demonstrate a positive
prospect of application of dilute alkaline pre-treatment to enhance
enzymatic saccharification and biobutanol production from
microalgal biomass.
Abstract: Nanophotocatalysts such as titanium (TiO2), zinc (ZnO), and iron (Fe2O3) oxides can be used in organic pollutants oxidation, and in many other applications. But among the challenges for technological application (scale-up) of the nanotechnology scientific developments two aspects are still little explored: research on environmental risk of the nanomaterials preparation methods, and the study of nanomaterials properties and/or performance variability. The environmental analysis was performed for six different methods of ZnO nanoparticles synthesis, and showed that it is possible to identify the more environmentally compatible process even at laboratory scale research. The obtained ZnO nanoparticles were tested as photocatalysts, and increased the degradation rate of the Rhodamine B dye up to 30 times.
Abstract: Iron oxide nanoparticle was synthesized by reactive-precipitation method followed by high speed centrifuge and phase transfer in order to stabilized nanoparticles in the solvent. Particle size of SPIO was 8.2 nm by SEM, and the hydraulic radius was 17.5 nm by dynamic light scattering method. Coercivity and saturated magnetism were determined by VSM (vibrating sample magnetometer), coercivity of nanoparticle was lower than 10 Hc, and the saturated magnetism was higher than 65 emu/g. Stabilized SPIO was then transferred to aqueous phase by reacted with excess amount of poly (ethylene glycol) (PEG) silane. After filtration and dialysis, the SPIO T2 contrast agent was ready to use. The hydraulic radius of final product was about 70~100 nm, the relaxation rates R2 (1/T2) measured by magnetic resonance imaging (MRI) was larger than 200(sec-1).
Abstract: The hydrogen peroxide treatment was able to
remediate chlorophenols, polycyclic aromatic hydrocarbons, diesel
and transformer oil contaminated soil. Chemical treatment of
contaminants adsorbed in peat resulted in lower contaminants-
removal and required higher addition of chemicals than the treatment
of contaminants in sand. The hydrogen peroxide treatment was found
to be feasible for soil remediation at natural soil pH. Contaminants in
soil could degrade with the addition of hydrogen peroxide only
indicating the ability of transition metals ions and minerals of these
metals presented in soil to catalyse the reaction of hydrogen peroxide
decomposition.
Abstract: Transesterification of candlenut (aleurites moluccana)
oil with methanol using potassium hydroxide as catalyst was
studied. The objective of the present investigation was to produce
the methyl ester for use as biodiesel. The operation variables
employed were methanol to oil molar ratio (3:1 – 9:1), catalyst
concentration (0.50 – 1.5 %) and temperature (303 – 343K). Oil
volume of 150 mL, reaction time of 75 min were fixed as common
parameters in all the experiments. The concentration of methyl ester
was evaluated by mass balance of free glycerol formed which was
analyzed by using periodic acid. The optimal triglyceride conversion
was attained by using methanol to oil ratio of 6:1, potassium
hydroxide as catalyst was of 1%, at room temperature. Methyl ester
formed was characterized by its density, viscosity, cloud and pour
points. The biodiesel properties had properties similar to those of
diesel oil, except for the viscosity that was higher.
Abstract: This study was to investigate the performance of
hybrid solvents blended between primary, secondary, or tertiary
amines and piperazine (PZ) for CO2 removal from flue gas in terms
of CO2 absorption capacity and regeneration efficiency at 90 oC.
Alkanolamines used in this work were monoethanolamine (MEA),
diethanolamine (DEA), and triethanolamine (TEA). The CO2
absorption was experimentally examined under atmospheric pressure
and room temperature. The results show that MEA blend with PZ
provided the maximum CO2 absorption capacity of 0.50 mol
CO2/mol amine while TEA provided the minimum CO2 absorption
capacity of 0.30 mol CO2/mol amine. TEA was easier to regenerate
for both first cycle and second cycle with less loss of absorption
capacity. The regeneration efficiency of TEA was 95.09 and 92.89 %,
for the first and second generation cycles, respectively.
Abstract: In the other to Study of drought stress and Selenium
spraying effect on superoxide dismotase (SOD) activity of rapeseed
(Brassica napus L.) cultivars in Shahr-e-Rey region, an experiment
carried out in Split factorial design in the basis of randomized
complete blocks with 4 replications in 2006. Irrigation in two levels:
Normal irrigation and irrigation with drought stress when the soil
electrical conductivity reached to 60 as main factor and rapeseed
cultivars in 3 levels Zarfam, Okapi, Opera and selenium spraying at
the beginning of flowering stage in 3 levels: 0, 16 and 21 g/ha as sub
factor.
The results showed that the simple and interaction effect of
irrigation, selenium and cultivars on SOD activity had significant
difference. In this case Zarfam cultivar with 2010 u.mg-1 protein and
Opera with 1454 u.mg-1 protein produced maximum and minimum
amounts of SOD activitiy. Interaction effect of irrigation and variety
showed that, normal irrigation in Opera with 1115 u.mg-1 protein
and drought stress in Zarfam with 2784 u.mg-1 protein conducted to
and minimum and maximum amounts of SOD activity.
Interaction effect of irrigation, cultivar and selenium on SOD
indicated that drought stress condition and 21 gr/ha selenium
spraying in Zarfam variety with 3146 u.mg-1 protein gained to
highest activities of SOD.
Abstract: Mining tailings represent a generating source of rich heavy metal material with a potential danger the public health and the environment, since these metals, under certain conditions, can leach and contaminate aqueous systems that serve like supplying potable water sources. The strategy for this work is based on the observation, experimentation and the simulation that can be obtained by binding real answers of the hydrodynamic behavior of metals leached from mining tailings, and the applied mathematics that provides the logical structure to decipher the individual effects of the general physicochemical phenomenon. The case of study presented herein focuses on mining tailings deposits located in Monte San Nicolas, Guanajuato, Mexico, an abandoned mine. This was considered the contamination source that under certain physicochemical conditions can favor the metal leaching, and its transport towards aqueous systems. In addition, the cartography, meteorology, geology and the hydrodynamics and hydrological characteristics of the place, will be helpful in determining the way and the time in which these systems can interact. Preliminary results demonstrated that arsenic presents a great mobility, since this one was identified in several superficial aqueous systems of the micro watershed, as well as in sediments in concentrations that exceed the established maximum limits in the official norms. Also variations in pH and potential oxide-reduction were registered, conditions that favor the presence of different species from this element its solubility and therefore its mobility.
Abstract: The mixed oxide nuclear fuel (MOX) of U and Pu contains several percent of fission products and minor actinides, such as neptunium, americium and curium. It is important to determine accurately the decay heat from Curium isotopes as they contribute significantly in the MOX fuel. This heat generation can cause samples to melt very quickly if excessive quantities of curium are present. In the present paper, we introduce a new approach that can predict the decay heat from curium isotopes. This work is a part of the project funded by King Abdulaziz City of Science and Technology (KASCT), Long-Term Comprehensive National Plan for Science, Technology and Innovations, and take place in King Abdulaziz University (KAU), Saudi Arabia. The approach is based on the numerical solution of coupled linear differential equations that describe decays and buildups of many nuclides to calculate the decay heat produced after shutdown. Results show the consistency and reliability of the approach applied.
Abstract: ZnO-SnO2 i.e. Zinc-Tin-Oxide (ZTO) thin films were
deposited on glass substrate with varying concentrations (ZnO:SnO2
- 100:0, 90:10, 70:30 and 50:50 wt.%) at room temperature by flash
evaporation technique. These deposited ZTO film were annealed at
450 0C in vacuum. These films were characterized to study the effect
of annealing on the structural, electrical, and optical properties.
Atomic force microscopy (AFM) and Scanning electron microscopy
(SEM) images manifest the surface morphology of these ZTO thin
films. The apparent growth of surface features revealed the formation
of nanostructure ZTO thin films. The small value of surface
roughness (root mean square RRMS) ensures the usefulness in
optical coatings. The sheet resistance was also found to be decreased
for both types of films with increasing concentration of SnO2. The
optical transmittance found to be decreased however blue shift has
been observed after annealing.
Abstract: The nickel and gold nanoclusters as supported
catalysts were analyzed by XAS, XRD and XPS in order to
determine their local, global and electronic structure. The present
study has pointed out a strong deformation of the local structure of
the metal, due to its interaction with oxide supports. The average
particle size, the mean squares of the microstrain, the particle size
distribution and microstrain functions of the supported Ni and Au
catalysts were determined by XRD method using Generalized Fermi
Function for the X-ray line profiles approximation. Based on EXAFS
analysis we consider that the local structure of the investigated
systems is strongly distorted concerning the atomic number pairs.
Metal-support interaction is confirmed by the shape changes of the
probability densities of electron transitions: Ni K edge (1s →
continuum and 2p), Au LIII-edge (2p3/2 → continuum, 6s, 6d5/2 and
6d3/2). XPS investigations confirm the metal-support interaction at
their interface.
Abstract: In this paper, the solubility of CO2 in AMP solution
have been measured at temperature range of ( 293, 303 ,313,323)
K.The amine concentration ranges studied are (2.0, 2.8, and 3.4) M.
A solubility apparatus was used to measure the solubility of CO2 in
AMP solution on samples of flue gases from Thermal and Central
Power Plants of Esfahan Steel Company. The modified Kent
Eisenberg model was used to correlate and predict the vapor-liquid
equilibria of the (CO2 + AMP + H2O) system. The model predicted
results are in good agreement with the experimental vapor-liquid
equilibrium measurements.
Abstract: Powder of La0.6Sr0.4CoO3-α (LSCO) was synthesized
by a combined citrate-EDTA method. The as-synthesized LSCO
powder was calcined, respectively at temperatures of 800, 900 and
1000 °C with different heating/cooling rates which are 2, 5, 10 and
15 °C min-1. The effects of heat treatments on the phase formation of
perovskite phase of LSCO were investigated by powder X-ray
diffraction (XRD). The XRD patterns revealed that the rate of
5 °C min-1 is the optimum heating/cooling rate to obtain a single
perovskite phase of LSCO with calcination temperature of 800 °C.
This result was confirmed by a thermogravimetric analysis (TGA) as
it showed a complete decomposition of intermediate compounds to
form oxide material was also observed at 800 °C.
Abstract: The nature of adsorbed species on catalytic surface
over an industrial precipitated iron-based high temperature catalyst
during FTS was investigated by in-situ DRIFTS and chemical
trapping. The formulation of the mechanism of oxygenates formation
and key intermediates were also discussed. Numerous oxygenated
precursors and crucial intermediates were found by in-situ DRIFTS,
such as surface acetate, acetyl and methoxide. The results showed that
adsorbed molecules on surface such as methanol or acetaldehyde
could react with basic sites such as lattice oxygen or free surface
hydroxyls. Adsorbed molecules also had reactivity of oxidizing.
Moreover, acetyl as a key intermediate for oxygenates was observed
by investigation of CH3OH + CO and CH3I + CO + H2. Based on the
nature of surface properties, the mechanism of oxygenates formation
on precipitated iron-based high temperature catalyst was discussed.
Abstract: The main purpose of this research is the calculation of implicit prices of the environmental level of air quality in the city of Moscow on the basis of housing property prices. The database used contains records of approximately 20 thousand apartments and has been provided by a leading real estate agency operating in Russia. The explanatory variables include physical characteristics of the houses, environmental (industry emissions), neighbourhood sociodemographic and geographic data: GPS coordinates of each house. The hedonic regression results for ecological variables show «negative» prices while increasing the level of air contamination from such substances as carbon monoxide, nitrogen dioxide, sulphur dioxide, and particles (CO, NO2, SO2, TSP). The marginal willingness to pay for higher environmental quality is presented for linear and log-log models.
Abstract: The paper relates to a catalyst, comprising copperchromium
spinel, coated on carrier γ-Al2O3. The effect of preparation
conditions on the active component composition and activity
behavior of the catalysts is discussed. It was found that the activity of
carbon monoxide, DME, formaldehyde and methanol oxidation
reaches a maximum at an active component content of 20 – 30 wt. %.
Temperature calcination at 500oC seems to be optimal for the γ–
alumina supported CuO-Cr2O3 catalysts for CO, DME, formaldehyde
and methanol oxidation. A three months industrial experiment was
carried out to elucidate the changes in the catalyst composition
during industrial exploitation of the catalyst and the main reasons for
catalyst deactivation.
It was concluded that the CuO–Cr2O3/γ–alumina supported
catalysts have enhanced activity toward CO, DME, formaldehyde
and methanol oxidation and that these catalysts are suitable for
industrial application. The main reason for catalyst deactivation
seems to be the deposition of iron and molybdenum, coming from the
main reactor, on the active component surface.
Abstract: In this study, a nickel film with nano-crystalline grains,
high hardness and smooth surface was electrodeposited using a post
supercritical carbon dioxide (CO2) mixed Watts electrolyte. Although
the hardness was not as high as its Sc-CO2 counterpart, the thin coating
contained significantly less number of nano-sized pinholes. By
measuring the escape concentration of the dissolved CO2 in post
Sc-CO2 mixed electrolyte with the elapsed time, it was believed that
the residue of dissolved CO2 bubbles should closely relate to the
improvement in hardness and surface roughness over its conventional
plating counterpart. Therefore, shortening the duration of
electroplating with the raise of current density up to 0.5 A/cm2 could
effectively retain more post Sc-CO2 mixing effect. This study not only
confirms the roles of dissolved CO2 bubbles in electrolyte but also
provides a potential process to overcome most issues associated with
the cost in building high-pressure chamber for large size products and
continuous plating using supercritical method.
Abstract: Fire disaster is the major factor to endanger the public
and environmental safety. People lost their life during fire disaster
mainly be attributed to the dense smoke and toxic gas under
combustion, which hinder the escape of people and the rescue of
firefighters under fire disaster. The smoke suppression effect of
several transitional metals oxide on the epoxy resin treated with
intumescent flame retardant and titanate couple agent
(EP/IFR/Titanate) system have been investigated. The results showed
manganese dioxide has great effect on reducing the smoke density rate
(SDR) of EP/IFR/Titanate system; however it has little effect to reduce
the maximum smoke density (MSD) of EP/IFR/Titanate system.
Copper oxide can decrease the maximum smoke density (MSD) and
smoke density rate of EP/IFR/Titanate system substantially. The MSD
and SDR of EP/IFR/Titanate system can reduce 20.3% and 39.1%
respectively when 2% of copper oxide is introduced.