Abstract: Depositional environment and source potential of the
different organic-rich levels of Devonian age (up to 990m thick) from
the onshore EC-1 well (Southern Tunisia) were investigated based on
the analysis of more than 130 cutting samples by different
geochemical techniques (Rock-Eval pyrolysis, GC-MS). The
obtained results including Rock Eval Pyrolysis data and biomarker
distribution (terpanes, steranes and aromatics) have been used to
describe the depositional environment and to assess the thermal
maturity of the Devonian organic matter. These results show that the
Emsian deposits exhibit poor to fair TOC contents. The associated
organic matter is composed of mixed kerogen (type II/III), as
indicated by the predominance of C29 steranes over C27 and C28
homologous, that was deposited in a slightly reduced environment
favoring organic matter preservation. Thermal maturity assessed from
Tmax, TNR and MPI-1 values shows a mature stage of organic
matter. The Middle Devonian (Eifelian) shales are rich in type II
organic matter that was deposited in an open marine depositional
environment. The TOC values are high and vary between 2 and 7%
indicating good to excellent source rock. The relatively high HI
values (reaching 547 mg HC/g TOC) and the low values of t19/t23
tricyclic terpane ratio (< 0.2) confirm the marine origin of the organic
matter (type II). During the Upper Devonian, the organic matter was
deposited under variable redox conditions, oxic to suboxic which is
clearly indicated by the low C35/C34 hopanes ratio, immature to
marginally mature with the vitrinite reflectance ranging from 0.5 to
0.7 Ro and Tmax value of 426°C-436 °C and the TOC values range
between 0.8% to 4%.
Abstract: The objective of this work is to study the effect of two
key factors - external magnetic field and applied current density
during template-based electrodeposition of nickel nanowires using an
electrode distance of 20 mm. Morphology, length, crystallite size and
crystallographic characterization of the grown nickel nanowires at an
electrode distance of 20mm are presented. For this electrode distance
of 20 mm, these two key electrodeposition factors when coupled was
found to reduce crystallite size with a higher growth length and
preferred orientation of Ni crystals. These observed changes can be
inferred to be due to coupled interaction forces induced by the
intensity of applied electric field (current density) and external
magnetic field known as magnetohydrodynamic (MHD) effect during
the electrodeposition process.
Abstract: In the present work, the dielectric properties of
Epoxy/MWCNT-muscovite HYBRID and MIXED composites based
on a ratio 30:70 were studied. The multi-wall carbon nanotubes
(MWCNT) were prepared using two methods: (a) MWCNTmuscovite
hybrids were synthesised by chemical vapour deposition
(CVD) and (b) physically mixing muscovite with MWCNT. The
effects of different preparation of the composites and filler loading
were evaluated. It was revealed that the dielectric constants of
HYBRID epoxy composites are slightly higher than MIXED epoxy
composites. It was also indicated that the dielectric constant increased
by increasing the MWCNT filler loading.
Abstract: The Al-MoO3-P-CdTe-Al MOS sandwich structures
were fabricated by vacuum deposition method on cleaned glass
substrates. Capacitance versus voltage measurements were performed
at different frequencies and sweep rates of applied voltages for oxide
and semiconductor films of different thicknesses. In the negative
voltage region of the C-V curve a high differential capacitance of the
semiconductor was observed and at high frequencies (
Abstract: Chemical vapor deposition (CVD) diamond coated
cutting tool has excellent cutting performance, it is the most ideal tool
for the processing of nonferrous metals and alloys, composites,
nonmetallic materials and other difficult-to-machine materials
efficiently and accurately. Depositing CVD diamond coating on the
cemented carbide with high cobalt content can improve its toughness
and strength, therefore, it is very important to research on the
preparation technology and cutting properties of CVD diamond coated
cemented carbide cutting tool with high cobalt content. The
preparation technology of boron-doped diamond (BDD) coating has
been studied and the coated drills were prepared. BDD coating were
deposited on the drills by using the optimized parameters and the SEM
results show that there are no cracks or collapses in the coating.
Cutting tests with the prepared drills against the silumin and aluminum
base printed circuit board (PCB) have been studied. The results show
that the wear amount of the coated drill is small and the machined
surface has a better precision. The coating does not come off during
the test, which shows good adhesion and cutting performance of the
drill.
Abstract: Thin-walled elements with a matrix set on a base of
high-valuable Portland cement with dispersed reinforcement from
alkali-resistant glass fibres are used in a range of applications as
claddings of buildings and infrastructure constructions as well as
various architectural elements of residential buildings.
Even though their elementary thickness and therefore total weight
is quite low, architects and building companies demand on even
further decreasing of the bulk density of these fibre-cement elements
for the reason of loading elimination of connected superstructures
and easier assembling in demand conditions.
By the means of various kinds of light-weight aggregates it is
possible to achieve light-weighing of these composite elements.
From the range of possible fillers with different material properties
granulated expanded glass worked the best.
By the means of laboratory testing an effect of two fillers based on
expanded glass on the fibre reinforced cement composite was
verified.
Practical applicability was tested in the production of commonly
manufactured glass fibre reinforced concrete elements, such as
channels for electrical cable deposition, products for urban equipment
and especially various cladding elements.
Even though these are not structural elements, it is necessary to
evaluate also strength characteristics and resistance to environment
for their durability in certain applications.
Abstract: Skin aging is a slow multifactorial process influenced
by both internal as well as external factors. Ultra-violet radiations
(UV), diet, smoking and personal habits are the most common
environmental factors that affect skin aging. Fat contents and fibrous
proteins as collagen and elastin are core internal structural
components. The direct influence of UV on elastin integrity and
health is central on aging of skin especially by time. The deposition
of abnormal elastic material is a major marker in a photo-aged skin.
Searching for compounds that may protect against cutaneous photodamage
is exceedingly valued. Retinoids and alpha hydroxy acids
have been endorsed by some researchers as possible candidates for
protecting and or repairing the effect of UV damaged skin. For
consolidating a better system of anti- and protective effects of such
anti-aging agents, we evaluated the combinatory effects of various
dosages of lactic acid and retinol on the dermal fibroblast’s elastin
levels exposed to UV. The UV exposed cells showed significant
reduction in the elastin levels. A combination of drugs with a higher
concentration of lactic acid (30 -35 mM) and a lower concentration of
retinol (10-15mg/mL) showed to work better in maintaining elastin
concentration in UV exposed cells. We assume this preservation
could be the result of increased tropo-elastin gene expression
stimulated by retinol whereas lactic acid probably repaired the UV
irradiated damage by enhancing the amount and integrity of the
elastin fibers.
Abstract: Carbon Deposits are often occurred inside the
industrial coke oven during coking process. Accumulation of carbon
deposits may cause a big issue, which seriously influences the coking
operation. The carbon is burning off by injecting fresh air through
pipes into coke oven which is an efficient way practically operated in
industries. The burning off carbon deposition in coke oven performed
by Computational Fluid Dynamics (CFD) method has provided an
evaluation of the feasibility study. A three dimensional, transient,
turbulent reacting flow simulation has performed with three different
injecting air flow rate and another kind of injecting configuration. The
result shows that injection higher air flow rate would effectively
reduce the carbon deposits. In the meantime, the opened charging
holes would suck extra oxygen from atmosphere to participate in
reactions. In term of coke oven operating limits, the wall temperatures
are monitored to prevent over-heating of the adiabatic walls during
burn-off process.
Abstract: Natural hydrocarbon seepage has helped petroleum
exploration as a direct indicator of gas and/or oil subsurface
accumulations. Surface macro-seeps are generally an indication of a
fault in an active Petroleum Seepage System belonging to a Total
Petroleum System. This paper describes a case study in which
multiple analytical techniques were used to identify and characterize
trace petroleum-related hydrocarbons and other volatile organic
compounds in groundwater samples collected from Sousse aquifer
(Central Tunisia). The analytical techniques used for analyses of
water samples included gas chromatography-mass spectrometry (GCMS),
capillary GC with flame-ionization detection, Compound
Specific Isotope Analysis, Rock Eval Pyrolysis. The objective of the
study was to confirm the presence of gasoline and other petroleum
products or other volatile organic pollutants in those samples in order
to assess the respective implication of each of the potentially
responsible parties to the contamination of the aquifer. In addition,
the degree of contamination at different depths in the aquifer was also
of interest. The oil and gas seeps have been investigated using
biomarker and stable carbon isotope analyses to perform oil-oil and
oil-source rock correlations. The seepage gases are characterized by
high CH4 content, very low δ13CCH4 values (-71,9 ‰) and high
C1/C1–5 ratios (0.95–1.0), light deuterium–hydrogen isotope ratios (-
198 ‰) and light δ13CC2 and δ13CCO2 values (-23,8‰ and-23,8‰
respectively) indicating a thermogenic origin with the contribution of
the biogenic gas. An organic geochemistry study was carried out on
the more ten oil seep samples. This study includes light hydrocarbon
and biomarkers analyses (hopanes, steranes, n-alkanes, acyclic
isoprenoids, and aromatic steroids) using GC and GC-MS. The
studied samples show at least two distinct families, suggesting two
different types of crude oil origins: the first oil seeps appears to be
highly mature, showing evidence of chemical and/or biological
degradation and was derived from a clay-rich source rock deposited
in suboxic conditions. It has been sourced mainly by the lower
Fahdene (Albian) source rocks. The second oil seeps was derived
from a carbonate-rich source rock deposited in anoxic conditions,
well correlated with the Bahloul (Cenomanian-Turonian) source rock.
Abstract: A nanocrystalline thin film of ZnSe was successfully
electrodeposited on copper substrate using a non-aqueous solution
and subsequently annealed in air at 400°C. XRD analysis indicates
the polycrystalline deposit of (111) plane in both the cases. The
sharpness of the peak increases due to annealing of the film and
average grain size increases to 20 nm to 27nm. SEM photograph
indicate that grains are uniform and densely distributed over the
surface. Annealing increases the average grain size by 20%. The EDS
spectroscopy shows the ratio of Zn & Se is 1.1 in case of annealed
film. AFM analysis indicates the average roughness of the film
reduces from 181nm to 165nm due to annealing of the film. The
bandgap also decreases from 2.71eV to 2.62eV.
Abstract: Remote sensing plays a vital role in mapping of
resources and monitoring of environments of the earth. In the present
research study, mapping and monitoring of clay siltations occurred in
the Alkhod Dam of Muscat, Sultanate of Oman are carried out using
low-cost multispectral Landsat and ASTER data. The dam is
constructed across the Wadi Samail catchment for ground water
recharge. The occurrence and spatial distribution of siltations in the
dam are studied with five years of interval from the year 1987 of
construction to 2014. The deposits are mainly due to the clay, sand
and silt occurrences derived from the weathering rocks of ophiolite
sequences occurred in the Wadi Samail catchment. The occurrences
of clays are confirmed by minerals identification using ASTER
VNIR-SWIR spectral bands and Spectral Angle Mapper supervised
image processing method. The presence of clays and their spatial
distribution are verified in the field. The study recommends the
technique and the low-cost satellite data to similar region of the
world.
Abstract: A computational fluid dynamics (CFD) model is
developed for rechargeable non-aqueous electrolyte lithium-air
batteries with a partial opening for oxygen supply to the cathode.
Multi-phase transport phenomena occurred in the battery are
considered, including dissolved lithium ions and oxygen gas in the
liquid electrolyte, solid-phase electron transfer in the porous
functional materials and liquid-phase charge transport in the
electrolyte. These transport processes are coupled with the
electrochemical reactions at the active surfaces, and effects of
discharge reaction-generated solid Li2O2 on the transport properties
and the electrochemical reaction rate are evaluated and implemented
in the model. The predicted results are discussed and analyzed in terms
of the spatial and transient distribution of various parameters, such as
local oxygen concentration, reaction rate, variable solid Li2O2 volume
fraction and porosity, as well as the effective diffusion coefficients. It
is found that the effect of the solid Li2O2 product deposited at the solid
active surfaces is significant on the transport phenomena and the
overall battery performance.
Abstract: Thin ZnO films are deposited on glass substrates via
sol–gel method and dip-coating. The films are prepared from zinc
acetate dehydrate as a starting reagent. After that the as-prepared
ZnO sol is aged for different periods (0, 1, 3, 5, 10, 15 and 30 days).
Nanocrystalline thin films are deposited from various sols. The
effect ZnO sols aging time on the structural and photocatalytic
properties of the films is studied. The films surface is studied by
Scanning Electron Microscopy. The effect of the aging time of the
starting solution is studied in the photocatalytic degradation of
Reactive Black 5 (RB5) by UV-vis spectroscopy. The experiments
are conducted upon UV-light illumination and in complete darkness.
The variation of the absorption spectra shows the degradation of RB5
dissolved in water, as a result of the reaction, occurring on the surface
of the films and promoted by UV irradiation. The initial
concentrations of dye (5, 10 and 20 ppm) and the effect of the aging
time are varied during the experiments. The results show, that the
increasing aging time of starting solution with respect to ZnO
generally promotes photocatalytic activity. The thin films obtained
from ZnO sol, which is aged 30 days have best photocatalytic
degradation of the dye (97,22%) in comparison with the freshly
prepared ones (65,92%). The samples and photocatalytic
experimental results are reproducible. Nevertheless, all films exhibit
a substantial activity in both UV light and darkness, which is
promising for the development of new ZnO photocatalysts by sol-gel
method.
Abstract: In this paper, two options of anodic alumina barrier
layer thinning have been demonstrated. The approaches varied with
the duration of the voltage step. It was found that too long step of the
barrier layer thinning process leads to chemical etching of the
nanopores on their top. At the bottoms pores are not fully opened
what is disadvantageous for further applications in nanofabrication.
On the other hand, while the duration of the voltage step is controlled
by the current density (value of the current density cannot exceed
75% of the value recorded during previous voltage step) the pores are
fully opened. However, pores at the bottom obtained with this
procedure have smaller diameter, nevertheless this procedure
provides electric contact between the bare aluminum (substrate) and
electrolyte, what is suitable for template assisted electrodeposition,
one of the most cost-efficient synthesis method in nanotechnology.
Abstract: In this paper, effect of marginal quality groundwater
on yield of cotton crop and soil salinity was studied. In this
connection, three irrigation treatments each with four replications
were applied. These treatments were i) use of canal water (T1), ii) use
of marginal quality groundwater from tubewell (T2), and iii)
conjunctive use by mixing with the ratio of 1:1 of canal water and
marginal quality tubewell water (T3).
Water was applied to the crop cultivated in Kharif season 2011; its
quantity has been measured using cut-throat flume. Total 11 watering
each of 50 mm depth have been applied from 20th April to 20th July,
2011. Further, irrigations were stopped due to monsoon rainfall up to
crop harvesting.
Maximum crop yield (seed cotton) was observed under T1 which
was 1,517 kg/ha followed by T3 (mixed canal and tubewell water)
having 1009 kg/ha and T2 i.e. marginal quality groundwater having
709 kg/ha. This concludes that crop yield in T2 and T3 in comparison
to T1was reduced by about 53 and 30% respectively.
It has been observed that yield of cotton crop is below potential
limit for three treatments due to unexpected rainfall at the time of full
flowering season; thus the yield was adversely affected.
However, salt deposition in soil profiles was not observed that is
due to leaching effect of heavy rainfall occurred during monsoon
season.
Abstract: Carbon nanotube is one of the most attractive materials
for the potential applications of nanotechnology due to its excellent
mechanical, thermal, electrical and optical properties. In this paper we
report a supercapacitor made of nickel foil electrodes, coated with
multiwall carbon nanotubes (MWCNTs) thin film using
electrophoretic deposition (EPD) method. Chemical vapor deposition
method was used for the growth of MWCNTs and ethanol was used as
a hydrocarbon source. High graphitic multiwall carbon nanotube was
found at 750oC analyzing by Raman spectroscopy. We observed the
electrochemical performance of supercapacitor by cyclic
voltammetry. The electrodes of supercapacitor fabricated from
MWCNTs exhibit considerably small equivalent series resistance
(ESR), and a high specific power density. Electrophoretic deposition
is an easy method in fabricating MWCNT electrodes for high
performance supercapacitor.
Abstract: This study presents a cost-effective approach for rapid
fabricating modeling platforms utilized in fused deposition modeling
system. A small-batch production of modeling platforms about 20
pieces can be obtained economically through silicone rubber mold
using vacuum casting without applying the plastic injection molding.
The air venting systems is crucial for fabricating modeling platform
using vacuum casting. Modeling platforms fabricated can be used for
building rapid prototyping model after sandblasting. This study offers
industrial value because it has both time-effectiveness and
cost-effectiveness.
Abstract: Yttrium oxide (Y2O3) films have been successfully
deposited with yttrium-ethylenediamine tetraacetic acid (EDTA·Y·H)
complexes prepared by various milling techniques. The effects of the
properties of the EDTA·Y·H complex on the properties of the
deposited Y2O3 films have been analyzed. Seven different types of the
raw EDTA·Y·H complexes were prepared by various commercial
milling techniques such as ball milling, hammer milling, commercial
milling, and mortar milling. The milled EDTA·Y·H complexes
exhibited various particle sizes and distributions, depending on the
milling method. Furthermore, we analyzed the crystal structure,
morphology and elemental distribution profile of the metal oxide films
deposited on stainless steel substrate with the milled EDTA·Y·H
complexes. Depending on the milling technique, the flow properties of
the raw powders differed. The X-ray diffraction pattern of all the
samples revealed the formation of Y2O3 crystalline phase, irrespective
of the milling technique. Of all the different milling techniques, the
hammer milling technique is considered suitable for fabricating dense
Y2O3 films.
Abstract: The hydrogenated amorphous carbon films (α-C:H)
were deposited on p-type Si (100) substrates at different thicknesses by
radio frequency plasma enhanced chemical vapor deposition
technique (rf-PECVD). Raman spectra display asymmetric
diamond-like carbon (DLC) peaks, representative of the α-C:H films.
The decrease of intensity ID/IG ratios revealed the sp3 content arise at
different thicknesses of the α-C:H films. In terms of mechanical
properties, the high hardness and elastic modulus values showed the
elastic and plastic deformation behaviors related to sp3 content in
amorphous carbon films. Electrochemical properties showed that the
α-C:H films exhibited excellent corrosion resistance in air-saturated
3.5 wt.% NaCl solution for pH 2 at room temperature. Thickness
increasing affected the small sp2 clusters in matrix, restricting the
velocity transfer and exchange of electrons. The deposited α-C:H films
exhibited excellent mechanical properties and corrosion resistance.
Abstract: Hydrogenated amorphous carbon (a-C:H) films have
been synthesized by a radio frequency plasma enhanced chemical
vapor deposition (rf-PECVD) technique with different bias voltage
from 0.0 to -0.5 kV. The Raman spectra displayed the polymer-like
hydrogenated amorphous carbon (PLCH) film with 0.0 to -0.1 and
a-C:H films with -0.2 to -0.5 kV of bias voltages. The surface chemical
information of all films were studied by X-ray photoelectron
spectroscopy (XPS) technique, presented to C-C (sp2 and sp3) and C-O
bonds, and relative carbon (C) and oxygen (O) atomics contents. The
O contamination had affected on structure and optical properties. The
true density of PLCH and a-C:H films were characterized by X-ray
refractivity (XRR) method, showed the result as in the range of
1.16-1.73 g/cm3 that depending on an increasing of bias voltage. The
hardness was proportional to the true density of films. In addition, the
optical properties i.e. refractive index (n) and extinction coefficient (k)
of these films were determined by a spectroscopic ellipsometry (SE)
method that give formation to in 1.62-2.10 (n) and 0.04-0.15 (k)
respectively. These results indicated that the optical properties
confirmed the Raman results as presenting the structure changed with
applied bias voltage increased.