Abstract: A novel method to produce a fast high voltage solid
states switch using Insulated Gate Bipolar Transistors (IGBTs) is
presented for discharge-pumped gas lasers. The IGBTs are connected
in series to achieve a high voltage rating. An avalanche transistor is
used as the gate driver. The fast pulse generated by the avalanche
transistor quickly charges the large input capacitance of the IGBT,
resulting in a switch out of a fast high-voltage pulse. The switching
characteristic of fast-high voltage solid state switch has been estimated
in the multi-stage series-connected IGBT with the applied voltage of
several tens of kV. Electrical circuit diagram and the mythology of
fast-high voltage solid state switch as well as experimental results
obtained are presented.
Abstract: This paper presents a study on Proportional Resonant
(PR) current control with additional PR harmonic compensators for
Grid Connected Photovoltaic (PV) Inverters. Both simulation and
experimental results will be presented. Testing was carried out on a
3kW Grid-Connected PV Inverter which was designed and
constructed for this research.
Abstract: Distributed Generation (DG) can help in reducing the
cost of electricity to the costumer, relieve network congestion and
provide environmentally friendly energy close to load centers. Its
capacity is also scalable and it provides voltage support at distribution
level. Hence, DG placement and penetration level is an important
problem for both the utility and DG owner. DG allocation and capacity
determination is a nonlinear optimization problem. The objective
function of this problem is the minimization of the total loss of the
distribution system. Also high levels of penetration of DG are a new
challenge for traditional electric power systems. This paper presents a
new methodology for the optimal placement of DG and penetration
level of DG in distribution system based on General Algebraic
Modeling System (GAMS) and Genetic Algorithm (GA).
Abstract: This paper represents performance of particle swarm
optimisation (PSO) algorithm based integral (I) controller and
proportional-integral controller (PI) for interconnected hydro-thermal
automatic generation control (AGC) with generation rate constraint
(GRC) and Thyristor controlled phase shifter (TCPS) in series with
tie line. The control strategy of TCPS provides active control of
system frequency. Conventional objective function integral square
error (ISE) and another objective function considering square of
derivative of change in frequencies of both areas and change in tie
line power are considered. The aim of designing the objective
function is to suppress oscillation in frequency deviations and change
in tie line power oscillation. The controller parameters are searched
by PSO algorithm by minimising the objective functions. The
dynamic performance of the controllers I and PI, for both the
objective functions, are compared with conventionally optimized I
controller.
Abstract: In this paper an isolated wind-diesel hybrid power
system has been considered for reactive power control study having
an induction generator for wind power conversion and synchronous
alternator with automatic voltage regulator (AVR) for diesel unit is
presented. The dynamic voltage stability evaluation is dependent on
small signal analysis considering a Static VAR Compensator (SVC)
and IEEE type -I excitation system. It's shown that the variable
reactive power source like SVC is crucial to meet the varying
demand of reactive power by induction generator and load and to
acquire an excellent voltage regulation of the system with minimum
fluctuations. Integral square error (ISE) criterion can be used to
evaluate the optimum setting of gain parameters. Finally the dynamic
responses of the power systems considered with optimum gain setting
will also be presented.
Abstract: This paper presents the hardware implemented and
validation for a special system to assist the unprofessional users of
car with back trailers. The system consists of two platforms; the front
car platform (C) and the trailer platform (T). The main objective is to
control the Trailer platform using the actuators found in the front
platform (c). The mobility of the platform (C) is investigated and
inverse and forward kinematics model is obtained for both platforms
(C) and (T).The system is simulated using Matlab M-file and the
simulation examples results illustrated the system performance. The
system is constructed with a hardware setup for the front and trailer
platform. The hardware experimental results and the simulated
examples outputs showed the validation of the hardware setup.
Abstract: The electric power supplied by a photovoltaic power
generation systems depends on the solar irradiation and temperature.
The PV system can supply the maximum power to the load at a
particular operating point which is generally called as maximum
power point (MPP), at which the entire PV system operates with
maximum efficiency and produces its maximum power. Hence, a
Maximum power point tracking (MPPT) methods are used to
maximize the PV array output power by tracking continuously the
maximum power point. The proposed MPPT controller is designed
for 10kW solar PV system installed at Cape Institute of Technology.
This paper presents the fuzzy logic based MPPT algorithm. However,
instead of one type of membership function, different structures of
fuzzy membership functions are used in the FLC design. The
proposed controller is combined with the system and the results are
obtained for each membership functions in Matlab/Simulink
environment. Simulation results are decided that which membership
function is more suitable for this system.
Abstract: This paper proposes a backward/forward sweep
method to analyze the power flow in radial distribution systems. The
distribution system has radial structure and high R/X ratios. So the
newton-raphson and fast decoupled methods are failed with
distribution system. The proposed method presents a load flow study
using backward/forward sweep method, which is one of the most
effective methods for the load-flow analysis of the radial distribution
system. By using this method, power losses for each bus branch and
voltage magnitudes for each bus node are determined. This method
has been tested on IEEE 33-bus radial distribution system and
effective results are obtained using MATLAB.
Abstract: This paper proposes a new technique to design a
fixed-structure robust loop shaping controller for the pneumatic
servosystem. In this paper, a new method based on a particle swarm
optimization (PSO) algorithm for tuning the weighting function
parameters to design an H∞ controller is presented. The PSO
algorithm is used to minimize the infinity norm of the transfer
function of the nominal closed loop system to obtain the optimal
parameters of the weighting functions. The optimal stability margin is
used as an objective in PSO for selecting the optimal weighting
parameters; it is shown that the proposed method can simplify the
design procedure of H∞ control to obtain optimal robust controller for
pneumatic servosystem. In addition, the order of the proposed
controller is much lower than that of the conventional robust loop
shaping controller, making it easy to implement in practical works.
Also two-degree-of-freedom (2DOF) control design procedure is
proposed to improve tracking performance in the face of noise and
disturbance. Result of simulations demonstrates the advantages of the
proposed controller in terms of simple structure and robustness
against plant perturbations and disturbances.
Abstract: Now-a-days autonomous mobile robots have found
applications in diverse fields. An autonomous robot system must be
able to behave in an intelligent manner to deal with complex and
changing environment. This work proposes the performance of path
planning and navigation of autonomous mobile robot using
Gravitational Search Algorithm (GSA), Simulated Annealing (SA)
and Particle Swarm optimization (PSO) based intelligent controllers
in an unstructured environment. The approach not only finds a valid
collision free path but also optimal one. The main aim of the work is
to minimize the length of the path and duration of travel from a
starting point to a target while moving in an unknown environment
with obstacles without collision. Finally, a comparison is made
between the three controllers, it is found that the path length and time
duration made by the robot using GSA is better than SA and PSO
based controllers for the same work.
Abstract: Several of the practical industrial control processes are
multivariable processes. Due to the relation amid the variables
(interaction), delay in the loops, it is very intricate to design a
controller directly for these processes. So first, the interaction of the
variables is analyzed using Relative Normalized Gain Array
(RNGA), which considers the time constant, static gain and delay
time of the processes. Based on the effect of RNGA, relative gain
array (RGA) and NI, the pair (control configuration) of variables to
be controlled by decentralized control is selected. The equivalent
transfer function (ETF) of the process model is estimated as first
order process with delay using the corresponding elements in the
Relative gain array and Relative average residence time array
(RARTA) of the processes. Secondly, a decentralized Proportional-
Integral (PI) controller is designed for each ETF simply using
frequency response specifications. Finally, the performance and
robustness of the algorithm is comparing with existing related
approaches to validate the effectiveness of the projected algorithm.
Abstract: This paper designs the four-phase Boost Converter
which overcomes the problem of high input ripple current and output
ripple voltage. Digital control is more convenient for such a topology
on basis of synchronization, phase shift operation, etc. Simulation
results are presented for open-loop and closed-loop for four phase
boost converter. This control scheme is applicable for PFC rectifiers
as well. Thus a comparative analysis based on the obtained results is
performed.
Abstract: In this paper, extract of papaya leaves are used as a
natural dye and combined by variations of solvent concentration
applied on DSSC (Dye-Sensitized Solar Cell). Indonesian geographic
located on the equator line occasions the magnitude of the potential
to develop organic solar cells made from extracts of chlorophyll as a
substitute for inorganic materials or synthetic dye on DSSC material.
Dye serves as absorbing photons which are then converted into
electrical energy. A conductive coated glass layer called TCO
(Transparent Conductive Oxide) is used as a substrate of electrode.
TiO2 nanoparticles as binding dye molecules, redox couple iodide/
tri-iodide as the electrolyte and carbon as the counter electrode in the
DSSC are used. TiO2 nanoparticles, organic dyes, electrolytes, and
counter electrode are arranged and combined with the layered
structure of the photo-catalyst absorption layer. Dye absorption
measurements using a spectrophotometer at 400-800 nm light
spectrum produces a total amount of chlorophyll 80.076 mg/l. The
test cell at 7 watt LED light with 5000 lux luminescence was
obtained Voc and Isc of 235.5 mV and 14 μA, respectively.
Abstract: The Simulation based VLSI Implementation of
FELICS (Fast Efficient Lossless Image Compression System)
Algorithm is proposed to provide the lossless image compression and
is implemented in simulation oriented VLSI (Very Large Scale
Integrated). To analysis the performance of Lossless image
compression and to reduce the image without losing image quality
and then implemented in VLSI based FELICS algorithm. In FELICS
algorithm, which consists of simplified adjusted binary code for
Image compression and these compression image is converted in
pixel and then implemented in VLSI domain. This parameter is used
to achieve high processing speed and minimize the area and power.
The simplified adjusted binary code reduces the number of arithmetic
operation and achieved high processing speed. The color difference
preprocessing is also proposed to improve coding efficiency with
simple arithmetic operation. Although VLSI based FELICS
Algorithm provides effective solution for hardware architecture
design for regular pipelining data flow parallelism with four stages.
With two level parallelisms, consecutive pixels can be classified into
even and odd samples and the individual hardware engine is
dedicated for each one. This method can be further enhanced by
multilevel parallelisms.
Abstract: One of the major difficulties introduced with wind
power penetration is the inherent uncertainty in production originating
from uncertain wind conditions. This uncertainty impacts many
different aspects of power system operation, especially the balancing
power requirements. For this reason, in power system development
planing, it is necessary to evaluate the potential uncertainty in future
wind power generation. For this purpose, simulation models are
required, reproducing the performance of wind power forecasts.
This paper presents a wind power forecast error simulation models
which are based on the stochastic process simulation. Proposed
models capture the most important statistical parameters recognized
in wind power forecast error time series. Furthermore, two distinct
models are presented based on data availability. First model uses
wind speed measurements on potential or existing wind power plant
locations, while the seconds model uses statistical distribution of wind
speeds.
Abstract: In-memory database systems are becoming popular
due to the availability and affordability of sufficiently large RAM and
processors in modern high-end servers with the capacity to manage
large in-memory database transactions. While fast and reliable inmemory
systems are still being developed to overcome cache misses,
CPU/IO bottlenecks and distributed transaction costs, disk-based data
stores still serve as the primary persistence. In addition, with the
recent growth in multi-tenancy cloud applications and associated
security concerns, many organisations consider the trade-offs and
continue to require fast and reliable transaction processing of diskbased
database systems as an available choice. For these
organizations, the only way of increasing throughput is by improving
the performance of disk-based concurrency control. This warrants a
hybrid database system with the ability to selectively apply an
enhanced disk-based data management within the context of inmemory
systems that would help improve overall throughput.
The general view is that in-memory systems substantially
outperform disk-based systems. We question this assumption and
examine how a modified variation of access invariance that we call
enhanced memory access, (EMA) can be used to allow very high
levels of concurrency in the pre-fetching of data in disk-based
systems. We demonstrate how this prefetching in disk-based systems
can yield close to in-memory performance, which paves the way for
improved hybrid database systems. This paper proposes a novel EMA
technique and presents a comparative study between disk-based EMA
systems and in-memory systems running on hardware configurations
of equivalent power in terms of the number of processors and their
speeds. The results of the experiments conducted clearly substantiate
that when used in conjunction with all concurrency control
mechanisms, EMA can increase the throughput of disk-based systems
to levels quite close to those achieved by in-memory system. The
promising results of this work show that enhanced disk-based
systems facilitate in improving hybrid data management within the
broader context of in-memory systems.
Abstract: A mixed method by combining modified pole
clustering technique and modified cauer continued fraction is
proposed for reducing the order of the large-scale dynamic systems.
The denominator polynomial of the reduced order model is obtained
by using modified pole clustering technique while the coefficients of
the numerator are obtained by modified cauer continued fraction.
This method generated 'k' number of reduced order models for kth
order reduction. The superiority of the proposed method has been
elaborated through numerical example taken from the literature and
compared with few existing order reduction methods.
Abstract: As the current status and growth of Indian automobile
industry is remarkable, transportation sectors are the main concern in
terms of energy security and climate change. Due to rising demand of
fuel and its dependency on foreign countries that affects the GDP of
nation, suggests that penetration of electrical vehicle will increase in
near future. So in this context analysis is done if the 10 percent of
conventional vehicles including cars, three wheelers and two
wheelers becomes electrical vehicles in near future which is also a
part of Nations Electric Mobility Mission Plan then the saving which
improves the nation’s economy is analyzed in detail. Whether the
Indian electricity grid is capable of taking this load with current
generation and demand all over the country is also analyzed in detail.
Current situation of Indian grid is analyzed and how the gap between
generation and demand can be reduced is discussed in terms of
increasing generation capacity and energy conservation measures.
Electrical energy conservation measures in Industry and especially in
rural areas have been analyzed to improve performance of Indian
electricity grid in context of electrical vehicle penetration in near
future. Author was a part of Vishvakarma yojna in which energy
losses were measured in 255 villages of Gujarat and solutions were
suggested to mitigate them and corresponding reports was submitted
to the authorities of Gujarat government.
Abstract: This paper presents a novel statistical description of
the counterpoise effective length due to lightning surges, where the
(impulse) effective length had been obtained by means of regressive
formulas applied to the transient simulation results. The effective
length is described in terms of a statistical distribution function, from
which median, mean, variance, and other parameters of interest could
be readily obtained. The influence of lightning current amplitude,
lightning front duration, and soil resistivity on the effective length has
been accounted for, assuming statistical nature of these parameters. A
method for determining the optimal counterpoise length, in terms of
the statistical impulse effective length, is also presented. It is based on
estimating the number of dangerous events associated with lightning
strikes. Proposed statistical description and the associated method
provide valuable information which could aid the design engineer in
optimising physical lengths of counterpoises in different grounding
arrangements and soil resistivity situations.
Abstract: The present work aims to throw light on the effects of
arcing in air on the surface state of contact pastilles made of silvernickel
Ag-Ni (60/40). Also, the photoelectric emission from these
electrical contacts has been investigated in the spectral range of 196-
256 nm. In order to study the effects of arcing on the EWF, the
metallic samples were subjected to electrical arcs in air, at
atmospheric pressure and room temperature, after that, they have
been introduced into the vacuum chamber of an experimental UHV
set-up for EWF measurements. Both Fowler method of isothermal
curves and linearized Fowler plots were used for the measurement of
the EWF by the photoelectric effect.
It has been found that the EWF varies with the number of applied
arcs. Thus, after 500 arcs in air, the observed EWF increasing is
probably due to progressive inclusion of oxide on alloy surface.
Microscopic examination is necessary to get better understandings on
EWF of silver alloys, for both virgin and arced electrical contacts.