Abstract: Ethnicity identification of face images is of interest in
many areas of application, but existing methods are few and limited.
This paper presents a fusion scheme that uses block-based uniform
local binary patterns and Haar wavelet transform to combine local
and global features. In particular, the LL subband coefficients of the
whole face are fused with the histograms of uniform local binary
patterns from block partitions of the face. We applied the principal
component analysis on the fused features and managed to reduce the
dimensionality of the feature space from 536 down to around 15
without sacrificing too much accuracy. We have conducted a number
of preliminary experiments using a collection of 746 subject face
images. The test results show good accuracy and demonstrate the
potential of fusing global and local features. The fusion approach is
robust, making it easy to further improve the identification at both
feature and score levels.
Abstract: A SnO2/CdS/CdTe heterojunction was fabricated by
thermal evaporation technique. The fabricated cells were annealed at
573K for periods of 60, 120 and 180 minutes. The structural
properties of the solar cells have been studied by using X-ray
diffraction. Capacitance- voltage measurements were studied for the
as-prepared and annealed cells at a frequency of 102 Hz. The
capacitance- voltage measurements indicated that these cells are
abrupt. The capacitance decreases with increasing annealing time.
The zero bias depletion region width and the carrier concentration
increased with increasing annealing time. The carrier transport
mechanism for the CdS/CdTe heterojunction in dark is tunneling
recombination. The ideality factor is 1.56 and the reverse bias
saturation current is 9.6×10-10A. The energy band lineup for the n-
CdS/p-CdTe heterojunction was investigated using current - voltage
and capacitance - voltage characteristics.
Abstract: In this paper, the significant wave height at the Upper Gulf of Thailand and the changing of wave height at Bangkhuntien shoreline were simulated by using the Simulating WAves Nearshore Model (SWAN) version 40.51. The simulated results indicated that the significant wave height by SWAN model corresponded with the observed data. The results showed that the maximum significant wave height at the Bangkhuntien shoreline were 1.06-2.05 m. and the average significant wave height at the Bangkhuntien shoreline were 0.30-0.47 m. The significant wave height can be used to calculate the erosion through the Bangkhuntien shoreline. The erosion rates at the Bangkhuntien shoreline were prepared by using the aerial photo and they were about 1.80 m/yr. from 1980- 1986, 4.75 m/yr from 1987-1993, 15.28 m/yr from 1994-1996 and 10.03 m/yr from 1997-2002. The relation between the wave energy and the erosion were in good agreement. Therefore, the significant wave height was one of the major factors of the erosion at the Bangkhuntien shoreline.
Abstract: Geopolymer cement was evaluated as wellbore sealing material for carbon dioxide geosequestration application. Curing of cement system in saline water and strength testing in triaxial stress state condition under lateral confinement is relevant to primary cementing in CO2 geosequestration wellbore in saline aquifer. Geopolymer cement was cured in saline water (both at ambient conditions for 28 days and heated (60°C) conditions for 12 hours) and tested for triaxial strength at different levels of lateral confinement. Normal water and few other curing techniques were also studied both for geopolymer and API ‘G’ cement. Results reported were compared to evaluate the suitability of saline water for curing of geopolymer cement. Unconfined compression test results showed higher strength for curing in saline water than normal water. Besides, testing strength under lateral confinement demonstrated the material failure behavior from brittle to plastic.
Abstract: The learning society has currently transformed from 'wired society' to become 'mobile society' which is facilitated by wireless network. To suit to this new paradigm, m-learning was given birth and rapidly building its prospect to be included in the future curriculum. Research and studies on m-learning spruced up in numerous aspects but there is still scarcity in studies on curriculum design of m-learning. This study is a part of an ongoing bigger study probing into the m-learning curriculum for secondary schools. The paper reports on the first phase of the study which aims to probe into the needs of curriculum design for m-learning at the secondary school level and the researcher adopted the needs analysis method. Data accrued from responses on survey questionnaires based on Lickert-point scale were analyzed statistically. The findings from this preliminary study serve as a basis for m-learning curriculum development for secondary schools.
Abstract: This study analyzes characteristics determining
member’s willingness to invest in cooperatives using ordered logit
model. The data were collected in a field survey among 122
cooperative members in north-central China. The descriptive analysis
of survey evidence suggests that cooperatives in China generally
having poor ability to deliver the processing services related to
product package, grading, and storage, performing worse in
profitability, inability of providing returns to capital and obtaining
agricultural loan. The regression results demonstrate that members’
farm size, their satisfaction with cooperative price preferential
services, attitudes toward cooperative operational scale and
development potential have statistically significant impact on
willingness to invest.
Abstract: The current paper presents the findings of a research
study on learners- barriers and motivators engaged into blended
programs in a workplace context. In this study, the participants were
randomly assigned to one of four parallel e-learning courses, each of
which was delivered using a different learning strategy. Data were
collected through web-based and telephone surveys developed by the
researchers. The results showed that vague instruction, time
management, and insufficient feedback were the top-most barriers to
blended learning. The major motivators for blended learning included
content relevance, flexibility in time, and the ability to work at own
pace.
Abstract: The study aimed to verify a hypothesis that a sense of
fulfillment in student life and perceived stress in training in the
facilities could affect vocational identity among social welfare
university students, in order to acquire implications for enhancing the
vocational consciousness. A questionnaire survey was conducted with
388 third- and fourth-year students of training course for certified
social workers in three universities in A prefecture in Japan. The
questionnaire was returned by 338 students, and 288 responses
(85.2%) were valid and used for the analysis. As a SEM result, the
hypothesized model proved to be fit to the data. Path coefficient of
sense of fulfillment of student life to vocational identity was
statistically positive. Path coefficient of training stress to vocational
identity was statistically negative.
Abstract: A prototype of an anomaly detection system was
developed to automate process of recognizing an anomaly of
roentgen image by utilizing fuzzy histogram hyperbolization image
enhancement and back propagation artificial neural network.
The system consists of image acquisition, pre-processor, feature
extractor, response selector and output. Fuzzy Histogram
Hyperbolization is chosen to improve the quality of the roentgen
image. The fuzzy histogram hyperbolization steps consist of
fuzzyfication, modification of values of membership functions and
defuzzyfication. Image features are extracted after the the quality of
the image is improved. The extracted image features are input to the
artificial neural network for detecting anomaly. The number of nodes
in the proposed ANN layers was made small.
Experimental results indicate that the fuzzy histogram
hyperbolization method can be used to improve the quality of the
image. The system is capable to detect the anomaly in the roentgen
image.
Abstract: Random Access Memory (RAM) is an important
device in computer system. It can represent the snapshot on how the
computer has been used by the user. With the growth of its
importance, the computer memory has been an issue that has been
discussed in digital forensics. A number of tools have been developed
to retrieve the information from the memory. However, most of the
tools have their limitation in the ability of retrieving the important
information from the computer memory. Hence, this paper is aimed
to discuss the limitation and the setback for two main techniques such
as process signature search and process enumeration. Then, a new
hybrid approach will be presented to minimize the setback in both
individual techniques. This new approach combines both techniques
with the purpose to retrieve the information from the process block
and other objects in the computer memory. Nevertheless, the basic
theory in address translation for x86 platforms will be demonstrated
in this paper.
Abstract: In this paper back-propagation artificial neural network
(BPANN )with Levenberg–Marquardt algorithm is employed to
predict the deformation of the upsetting process. To prepare a
training set for BPANN, some finite element simulations were
carried out. The input data for the artificial neural network are a set
of parameters generated randomly (aspect ratio d/h, material
properties, temperature and coefficient of friction). The output data
are the coefficient of polynomial that fitted on barreling curves.
Neural network was trained using barreling curves generated by
finite element simulations of the upsetting and the corresponding
material parameters. This technique was tested for three different
specimens and can be successfully employed to predict the
deformation of the upsetting process
Abstract: We have fabricated a-IGZO TFT and investigated the
stability under positive DC and AC bias stress. The threshold voltage
of a-IGZO TFT shifts positively under those biases, and that reduces
on-current. For this reason, conventional shift-register circuit
employing TFTs which stressed by positive bias will be unstable, may
do not work properly. We have designed a new 6-transistor
shift-register, which has less transistors than prior circuits. The TFTs
of the proposed shift-register are not suffering from positive DC or AC
stress, mainly kept unbiased. Despite the compact design, the stable
output signal was verified through the SPICE simulation even under
RC delay of clock signal.
Abstract: Tomato nutrition value, color, flavor of their fruits and products depends mainly on lycopene, β-carotene, ascorbic acid, sugars and their ratio. The two most important carotenoids in fruits of tomato are lycopene, which determined fruits red color, and β- carotene, which accounts for approximately 7% of the tomato carotenoids. Therefore, tomato products and their quality can be well characterized by the content of these elements.Maturity at harvest is very important to composition and quality of tomatoes. This is especially a problem with tomatoes picked green since it is difficult to differentiate between mature and immature-green fruits. Typical and advanced mature-green tomatoes will usually attain a much better flavor than those picked at the immature or partially mature stages.To better understand the synthesis of biochemical compounds, their concentration should be compared not only at the last stage of maturity, but also during all fruit ripening period in different varieties.
Abstract: Today, incorrect use of lands and land use changes,
excessive grazing, no suitable using of agricultural farms, plowing on
steep slopes, road construct, building construct, mine excavation etc
have been caused increasing of soil erosion and sediment yield. For
erosion and sediment estimation one can use statistical and empirical
methods. This needs to identify land unit map and the map of
effective factors. However, these empirical methods are usually time
consuming and do not give accurate estimation of erosion. In this
study, we applied GIS techniques to estimate erosion and sediment of
Menderjan watershed at upstream Zayandehrud river in center of
Iran. Erosion faces at each land unit were defined on the basis of land
use, geology and land unit map using GIS. The UTM coordinates of
each erosion type that showed more erosion amounts such as rills and
gullies were inserted in GIS using GPS data. The frequency of
erosion indicators at each land unit, land use and their sediment yield
of these indices were calculated. Also using tendency analysis of
sediment yield changes in watershed outlet (Menderjan hydrometric
gauge station), was calculated related parameters and estimation
errors. The results of this study according to implemented watershed
management projects can be used for more rapid and more accurate
estimation of erosion than traditional methods. These results can also
be used for regional erosion assessment and can be used for remote
sensing image processing.
Abstract: This paper investigates vortex shedding processes
occurring at the end of a stack of parallel plates, due to an oscillating
flow induced by an acoustic standing wave within an acoustic
resonator. Here, Particle Image Velocimetry (PIV) is used to quantify
the vortex shedding processes within an acoustic cycle
phase-by-phase, in particular during the “ejection" of the fluid out of
the stack. Standard hot-wire anemometry measurement is also applied
to detect the velocity fluctuations near the end of the stack.
Combination of these two measurement techniques allowed a detailed
analysis of the vortex shedding phenomena. The results obtained show
that, as the Reynolds number varies (by varying the plate thickness
and drive ratio), different flow patterns of vortex shedding are
observed by the PIV measurement. On the other hand, the
time-dependent hot-wire measurements allow obtaining detailed
frequency spectra of the velocity signal, used for calculating
characteristic Strouhal numbers. The impact of the plate thickness and
the Reynolds number on the vortex shedding pattern has been
discussed. Furthermore, a detailed map of the relationship between the
Strouhal number and Reynolds number has been obtained and
discussed.
Abstract: The objective of the research was to evaluate the
hardness stability of milk pomade sweets packed in several
packaging materials (OPP, Multibarrier 60 HFP, BIALON 65
HFP, BIALON 50 HFP, ECOLEAN) by several packaging
technologies – modified atmosphere (MAP) (consisting of
30% CO2+70% N2; 30% N2+70% CO2 and 100% CO2) and
control – in air ambiance. Samples were stored at the room
temperature +21±1 °C. The studies of the samples were
carried out before packaging and after 2, 4, 6, 8, and 10
storage weeks.
Abstract: KSLV-I(Korea Space Launch Vehicle-I) is designed as
a launch vehicle to enter a 100 kg-class satellite to the LEO(Low Earth
Orbit). Attitude angles of the upper-stage, including roll, pitch and
yaw are controlled by the cold gas thruster system using nitrogen gas.
The cold gas thruster is an actuator in the RCS(Reaction Control
System). To design an attitude controller for the upper-stage, thrust
measurement in vacuum condition is required. In this paper, the new
thrust measurement system and calibration mechanism are developed
and measurement errors and signal processing method are presented.
Abstract: The leaching rate of 137Cs from spent mix bead (anion and cation) exchange resins in a cement-bentonite matrix has been studied. Transport phenomena involved in the leaching of a radioactive material from a cement-bentonite matrix are investigated using three methods based on theoretical equations. These are: the diffusion equation for a plane source an equation for diffusion coupled to a firstorder equation and an empirical method employing a polynomial equation. The results presented in this paper are from a 25-year mortar and concrete testing project that will influence the design choices for radioactive waste packaging for a future Serbian radioactive waste disposal center.
Abstract: Cluster analysis divides data into groups that are
meaningful, useful, or both. Analysis of biological data is creating a
new generation of epidemiologic, prognostic, diagnostic and
treatment modalities. Clustering of protein sequences is one of the
current research topics in the field of computer science. Linear
relation is valuable in rule discovery for a given data, such as if value
X goes up 1, value Y will go down 3", etc. The classical linear
regression models the linear relation of two sequences perfectly.
However, if we need to cluster a large repository of protein sequences
into groups where sequences have strong linear relationship with
each other, it is prohibitively expensive to compare sequences one by
one. In this paper, we propose a new technique named General
Regression Model Technique Clustering Algorithm (GRMTCA) to
benignly handle the problem of linear sequences clustering. GRMT
gives a measure, GR*, to tell the degree of linearity of multiple
sequences without having to compare each pair of them.
Abstract: This paper presents an experimental investigation of
transformer dielectric response and solid insulation water content.
The dielectric response was carried out on the base of Hybrid
Frequency Dielectric Spectroscopy and Polarization Current
measurements method (FDS &PC). The calculation of the water
content in paper is based on the water content in oil and the obtained
equilibrium curves. A reference measurements were performed at
equilibrium conditions for water content in oil and paper of
transformer at different stable temperatures (25, 50, 60 and 70°C) to
prepare references to evaluate the insulation behavior at the not
equilibrium conditions. Some measurements performed at the
different simulated normal working modes of transformer operation
at the same temperature where the equilibrium conditions. The
obtained results show that when transformer temperature is mach
more than the its ambient temperature, the transformer temperature
decreases immediately after disconnecting the transformer from the
network and this temperature reduction influences the transformer
insulation condition in the measuring process. In addition to the oil
temperature at the near places to the sensors, the temperature
uniformity in transformer which can be changed by a big change in
the load of transformer before the measuring time will influence the
result. The investigations have shown that the extremely influence of
the time between disconnecting the transformer and beginning the
measurements on the results. And the online monitoring for water
content in paper measurements, on the basis of the oil water content
on line monitoring and the obtained equilibrium curves. The
measurements where performed continuously and for about 50 days
without any disconnection in the prepared the adiabatic room.