Abstract: Low carbon deep drawing steel DC 01 according to EN 10130-91 was nitrooxidized in dissociated ammonia at 580°C/45 min and consequently oxidised at 380°C/5 min in vapour of distilled water. Material after nitrooxidation had 54 % increase of yield point, 34 % increase of strength and 10-times increased resistance to atmospheric corrosion in comparison to the material before nitrooxidation. The microstructure of treated material consisted of thin ε-phase layer connected to layer containing precipitated massive needle shaped Fe4N - γ' nitrides. This layer passed to a diffusion layer consisting of fine irregular shaped Fe16N2 - α'' nitrides regularly dispersed in ferritic matrix. Fatigue properties were examined under bending load with frequency of 20 kHz and sinusoidal symmetric cycle. The results confirmed positive influence of nitrooxidation on fatigue properties as fatigue limit of treated material was double in comparison to untreated material.
Abstract: In this communication a quantitative modeling
approach is applied to construct model for the exchange of gases
from open sewer channel to the atmosphere. The data for the
exchange of gases of the open sewer channel for the year January
1979 to December 2006 is utilized for the construction of the model.
The study reveals that stream flow of the open sewer channel
exchanges the toxic gases continuously with time varying scale. We
find that the quantitative modeling approach is more parsimonious
model for these exchanges. The usual diagnostic tests are applied for
the model adequacy. This model is beneficial for planner and
managerial bodies for the improvement of implemented policies to
overcome future environmental problems.
Abstract: Dynamic of phytoplankton blooms in the Baltic Sea
has been analyzed applying the numerical ecosystem model 3D
CEMBS. The model consists of the hydrodynamic model (POP,
version 2.1) and the ice model (CICE, version 4.0), which are
imposed by the atmospheric data model (DATM7). The 3D
model has an ecosystem module, activated in 2012 in the operational
mode. The ecosystem model consists of 11 main variables: biomass
of small-size phytoplankton and large-size phytoplankton
and cyanobacteria, zooplankton biomass, dissolved and molecular
detritus, dissolved oxygen concentration, as well as concentrations of
nutrients, including: nitrates, ammonia, phosphates and silicates. The
3D-CEMBS model is an effective tool for solving problems related to
phytoplankton blooms dynamic in the Baltic Sea
Abstract: This paper deals about four items assembly process of
linear drive. This assembly will be realized in flexible assembly cell
on Institute of Manufacturing Systems and Applied Mechanics. There
is defined manufacturing cell, individual actuators created our
flexible cell. Next chapter is about control type, detailed describe a
sequence control type, which will be used in mentioned flexible
assembly cell. All cell control is divided in individual steps
instructions. There instructions illustrate table number III.
Abstract: In this work we present some matrix operators named
circulant operators and their action on square matrices. This study on
square matrices provides new insights into the structure of the space
of square matrices. Moreover it can be useful in various fields as in
agents networking on Grid or large-scale distributed self-organizing
grid systems.
Abstract: In this paper we propose a new approach for flexible document categorization according to the document type or genre instead of topic. Our approach implements two homogenous classifiers: contextual classifier and logical classifier. The contextual classifier is based on the document URL, whereas, the logical classifier use the logical structure of the document to perform the categorization. The final categorization is obtained by combining contextual and logical categorizations. In our approach, each document is assigned to all predefined categories with different membership degrees. Our experiments demonstrate that our approach is best than other genre categorization approaches.
Abstract: Software and applications are subjected to serious and damaging security threats, these threats are increasing as a result of increased number of potential vulnerabilities. Security testing is an indispensable process to validate software security requirements and to identify security related vulnerabilities. In this paper we analyze and compare different available vulnerabilities testing techniques based on a pre defined criteria using analytical hierarchy process (AHP). We have selected five testing techniques which includes Source code analysis, Fault code injection, Robustness, Stress and Penetration testing techniques. These testing techniques have been evaluated against five criteria which include cost, thoroughness, Ease of use, effectiveness and efficiency. The outcome of the study is helpful for researchers, testers and developers to understand effectiveness of each technique in its respective domain. Also the study helps to compare the inner working of testing techniques against a selected criterion to achieve optimum testing results.
Abstract: The problem of controlling a two link robotic manipulator, consisting of a rotating and a prismatic links, is addressed. The actuations of both links are assumed to have unknown dead zone nonlinearities and friction torques modeled by LuGre friction model. Because of the existence of the unknown dead zone and friction torque at the actuations, unknown parameters and unmeasured states would appear to be part of the overall system dynamics that need for estimation. Unmeasured states observer, unknown parameters estimators, and robust adaptive control laws have been derived such that closed loop global stability is achieved. Simulation results have been performed to show the efficacy of the suggested approach.
Abstract: This paper presents an automatic feature recognition
method based on center-surround difference detecting and fuzzy logic
that can be applied in ground-penetrating radar (GPR) image
processing. Adopted center-surround difference method, the salient
local image regions are extracted from the GPR images as features of
detected objects. And fuzzy logic strategy is used to match the
detected features and features in template database. This way, the
problem of objects detecting, which is the key problem in GPR image
processing, can be converted into two steps, feature extracting and
matching. The contributions of these skills make the system have the
ability to deal with changes in scale, antenna and noises. The results of
experiments also prove that the system has higher ratio of features
sensing in using GPR to image the subsurface structures.
Abstract: Supplier selection, in real situation, is affected by
several qualitative and quantitative factors and is one of the most
important activities of purchasing department. Since at the time of
evaluating suppliers against the criteria or factors, decision makers
(DMS) do not have precise, exact and complete information, supplier
selection becomes more difficult. In this case, Grey theory helps us
to deal with this problem of uncertainty. Here, we apply Technique
for Order Preference by Similarity to Ideal Solution (TOPSIS)
method to evaluate and select the best supplier by using interval
fuzzy numbers. Through this article, we compare TOPSIS with some
other approaches and afterward demonstrate that the concept of
TOPSIS is very important for ranking and selecting right supplier.
Abstract: The purpose of this paper is to analyze the case of the
U.S. Pivot and to suggest an appropriate model including entry
strategies and success factors for QPS of Cable TV. The
telecommunication companies have been operating QPS including
IPTV service, which enables them to cross over broadcasting areas.
Due to this circumstance, the Cable TV operators are now concerned
and are planning to add QPS with the mobile service. Based on the
Porter's five forces model, an analytical framework has been proposed
to MVNO in Cable TV industry in the United States. As a result of this
study, MVNO in Cable TV industry has to have a clear killer
application with their sufficient contents. Subsequently, the direction
of the future Cable TV industry is proposed.
Abstract: Single nucleotide polymorphisms (SNPs) hold much promise as a basis for disease-gene association. However, research is limited by the cost of genotyping the tremendous number of SNPs. Therefore, it is important to identify a small subset of informative SNPs, the so-called tag SNPs. This subset consists of selected SNPs of the genotypes, and accurately represents the rest of the SNPs. Furthermore, an effective evaluation method is needed to evaluate prediction accuracy of a set of tag SNPs. In this paper, a genetic algorithm (GA) is applied to tag SNP problems, and the K-nearest neighbor (K-NN) serves as a prediction method of tag SNP selection. The experimental data used was taken from the HapMap project; it consists of genotype data rather than haplotype data. The proposed method consistently identified tag SNPs with considerably better prediction accuracy than methods from the literature. At the same time, the number of tag SNPs identified was smaller than the number of tag SNPs in the other methods. The run time of the proposed method was much shorter than the run time of the SVM/STSA method when the same accuracy was reached.
Abstract: The electrolyte stirring method of anodization etching
process for manufacturing porous silicon (PS) is reported in this work.
Two experimental setups of nature air stirring (PS-ASM) and
electrolyte stirring (PS-ESM) are employed to clarify the influence of
stirring mechanisms on electrochemical etching process. Compared to
traditional fabrication without any stirring apparatus (PS-TM), a large
plateau region of PS surface structure is obtained from samples with
both stirring methods by the 3D-profiler measurement. Moreover, the
light emission response is also improved by both proposed electrolyte
stirring methods due to the cycling force in electrolyte could
effectively enhance etch-carrier distribution while the electrochemical
etching process is made. According to the analysis of statistical
calculation of photoluminescence (PL) intensity, lower standard
deviations are obtained from PS-samples with studied stirring methods,
i.e. the uniformity of PL-intensity is effectively improved. The
calculated deviations of PL-intensity are 93.2, 74.5 and 64,
respectively, for PS-TM, PS-ASM and PS-ESM.
Abstract: The potential of economically cheaper cellulose
containing natural materials like rice husk was assessed for nickel
adsorption from aqueous solutions. The effects of pH, contact time,
sorbent dose, initial metal ion concentration and temperature on the
uptake of nickel were studied in batch process. The removal of nickel
was dependent on the physico-chemical characteristics of the
adsorbent, adsorbate concentration and other studied process
parameters. The sorption data has been correlated with Langmuir,
Freundlich and Dubinin-Radush kevich (D-R) adsorption models. It
was found that Freundlich and Langmuir isotherms fitted well to the
data. Maximum nickel removal was observed at pH 6.0. The
efficiency of rice husk for nickel removal was 51.8% for dilute
solutions at 20 g L-1 adsorbent dose. FTIR, SEM and EDAX were
recorded before and after adsorption to explore the number and
position of the functional groups available for nickel binding on to
the studied adsorbent and changes in surface morphology and
elemental constitution of the adsorbent. Pseudo-second order model
explains the nickel kinetics more effectively. Reusability of the
adsorbent was examined by desorption in which HCl eluted 78.93%
nickel. The results revealed that nickel is considerably adsorbed on
rice husk and it could be and economic method for the removal of
nickel from aqueous solutions.
Abstract: In this paper, a novel deinterlacing algorithm is
proposed. The proposed algorithm approximates the distribution of the
luminance into a polynomial function. Instead of using one
polynomial function for all pixels, different polynomial functions are
used for the uniform, texture, and directional edge regions. The
function coefficients for each region are computed by matrix
multiplications. Experimental results demonstrate that the proposed
method performs better than the conventional algorithms.
Abstract: In this article, using finite element analysis (FEA)
and an X-ray diffractometer (XRD), cold-sprayed titanium particles
on a steel substrate is investigated in term of cooling time and the
development of residual strains. Three cooling-down models of
sprayed particles after deposition stage are simulated and discussed:
the first model (m1) considers conduction effect to the substrate only,
the second model (m2) considers both conduction as well as
convection effect to the environment, and the third model (m3) which
is the same as the second model but with the substrate heated to a
near particle temperature before spraying. Thereafter, residual strains
developed in the third model is compared with the experimental
measurement of residual strains, which involved a Bruker D8
Advance Diffractometer using CuKa radiation (40kV, 40mA)
monochromatised with a graphite sample monochromator. For
deposition conditions of this study, a good correlation was found to
exist between the FEA results and XRD measurements of residual
strains.
Abstract: Since polymerase chain reaction (PCR) has been
invented, it has emerged as a powerful tool in genetic analysis. The
PCR products are closely linked with thermal cycles. Therefore, to
reduce the reaction time and make temperature distribution uniform in
the reaction chamber, a novel oscillatory thermal cycler is designed.
The sample is placed in a fixed chamber, and three constant isothermal
zones are established and lined in the system. The sample is oscillated
and contacted with three different isothermal zones to complete
thermal cycles. This study presents the design of the geometric
characteristics of the chamber. The commercial software
CFD-ACE+TM is utilized to investigate the influences of various
materials, heating times, chamber volumes, and moving speed of the
chamber on the temperature distributions inside the chamber. The
chamber moves at a specific velocity and the boundary conditions
with time variations are related to the moving speed. Whereas the
chamber moves, the boundary is specified at the conditions of the
convection or the uniform temperature. The user subroutines compiled
by the FORTRAN language are used to make the numerical results
realistically. Results show that the reaction chamber with a rectangular
prism is heated on six faces; the effects of various moving speeds of
the chamber on the temperature distributions are examined. Regarding
to the temperature profiles and the standard deviation of the
temperature at the Y-cut cross section, the non-uniform temperature
inside chamber is found as the moving speed is larger than 0.01 m/s.
By reducing the heating faces to four, the standard deviation of the
temperature of the reaction chamber is under 1.4×10-3K with the range
of velocities between 0.0001 m/s and 1 m/s. The nature convective
boundary conditions are set at all boundaries while the chamber moves
between two heaters, the effects of various moving velocities of the
chamber on the temperature distributions are negligible at the assigned
time duration.
Abstract: The autonomic nervous system has a regulatory
structure that helps people adapt to changes in their environment by
adjusting or modifying some functions in response to stress, and regulating involuntary function of human organs. The purpose of this
study was to investigate the effect of combined stimulation, both
far-infrared heating and chiropractic, on the autonomic nervous system
activities using thermal image and heart rate variability. Six healthy subjects participated in this test. We compared the before and after
autonomic nervous system activities through obtaining thermal image
and photoplethysmogram signal. The thermal images showed that the
combined stimulation changed subject-s body temperature more
highly and widely than before. The result of heart rate variability
indicated that LF/HF ratio decreased. We concluded that combined
stimulation activates autonomic nervous system, and expected other
possibilities of this combined stimulation.
Abstract: This paper presents a solution for ceramic cutting tools availability in interrupted machining. Experiments were performed on a special fixture – the interrupted cut simulator. This fixture was constructed at our Department of Machining and Assembly within the scope of a project by the Czech Science Foundation. The goals of the tests were to contribute to the wider usage of these cutting materials in machining, especially in interrupted machining. Through the centuries, producers of ceramic cutting tools have taken big steps forward. Namely, increasing durability in maintaining high levels of strength and hardness lends an advantage. Some producers of these materials advise cutting inserts for interrupted machining at the present time [1, 2].
Abstract: Twenty seven tektites from the Wenchang area, Hainan
province (south China) and five tektites from the Khon Kaen area
(northeast Thailand) were analyzed for major and trace element
contents and Rb-Sr isotopic compositions. All the samples studied are
splash-form tektites. Tektites of this study are characterized by high
SiO2 contents ranging from 71.95 to 74.07 wt% which is consistent
with previously published analyses of Australasian tektites. The trace
element ratios Ba/Rb (avg. 3.89), Th/Sm (avg. 2.40), Sm/Sc (avg.
0.45), Th/Sc (avg. 0.99) and the rare earth elements (REE) contents of
tektites of this study are similar to the average upper continental crust.
Based on the chemical composition, it is suggested that tektites in this
study are derived from similar parental material and are similar to the
post-Archean upper crustal rocks. The major and trace element
abundances of tektites analyzed indicate that the parental material of
tektites may be a terrestrial sedimentary deposit. The tektites from the
Wenchang area, Hainan Island have high positive εSr(0)
values-ranging from 184.5~196.5 which indicate that the parental
material for these tektites have similar Sr isotopic compositions to old
terrestrial sedimentary rocks and they were not dominantly derived
from recent young sediments (such as soil or loess). Based on Rb-Sr
isotopic data, it has been suggested by Blum (1992) [1]that the
depositional age of sedimentary target materials is close to 170Ma
(Jurassic). According to the model suggested by Ho and Chen
(1996)[2], mixing calculations for various amounts and combinations
of target rocks have been carried out. We consider that the best fit for
tektites from the Wenchang area is a mixture of 47% shale, 23%
sandstone, 25% greywacke and 5% quartzite, and the other tektites
from Khon Kaen area is a mixture of 46% shale, 2% sandstone, 20%
greywacke and 32% quartzite.