Abstract: This paper discusses on the use of Spline Interpolation
and Mean Square Error (MSE) as tools to process data acquired from
the developed simulator that shall replicate sea bed logging environment.
Sea bed logging (SBL) is a new technique that uses marine
controlled source electromagnetic (CSEM) sounding technique and is
proven to be very successful in detecting and characterizing hydrocarbon
reservoirs in deep water area by using resistivity contrasts. It uses
very low frequency of 0.1Hz to 10 Hz to obtain greater wavelength.
In this work the in house built simulator was used and was provided
with predefined parameters and the transmitted frequency was varied
for sediment thickness of 1000m to 4000m for environment with and
without hydrocarbon. From series of simulations, synthetics data were
generated. These data were interpolated using Spline interpolation
technique (degree of three) and mean square error (MSE) were
calculated between original data and interpolated data. Comparisons
were made by studying the trends and relationship between frequency
and sediment thickness based on the MSE calculated. It was found
that the MSE was on increasing trends in the set up that has the
presence of hydrocarbon in the setting than the one without. The MSE
was also on decreasing trends as sediment thickness was increased
and with higher transmitted frequency.
Abstract: Optical 1x12 fused-taper-twisted polymer optical fiber (POF) couplers has been fabricated by a perform technique. Characterization of the coupler which proposed to be used in passive night vision application to tracking a blind sport area was reported. During the development process of fused-taper-twisted POF couplers was carried out, red LED fully utilized to be injected into the couplers to test the quality of fabricated couplers. Some characterization parameters, such as optical output power, POFs attenuation characteristics and power losses on the network were observed. The maximum output power efficiency of the coupler is about 40%, but it can be improved gradually through experience and practice.
Abstract: Shippers are concentrating on the core competency to
stay competitive and outsourcing the logistic activities to the third
party who is expert in this field. This third party logistics (3PL) is
drawing the due attention at government, industrial, academicians
and practitioner-s levels. If the logistics cost in India can be brought
down from the current level of 13% of GDP to 9% (level in the U.S.),
the savings would be around Rs 3 lakh crore approximately per
annum. But the problem with the shippers is to select the suitable
3PL provider. Various criteria for selection of 3PL have been listed
in the literature which are discussed in the present literature review.
Every shipper will select the criteria suitable to its own requirement
which have to be dynamically reviewed time to time so as to fit in the
ever changing environment.
Abstract: Current air conditioning system is using refrigerant as
the cooling medium. The main purpose of this study is to develop an
air conditioning system using chill water as the cooling medium. In
this system, chill water used to replace refrigerant as the cooling
medium. This study is focus on the split type unit air conditioning
system only. It will be involving some renovation on the indoor unit
and freezer. The cooling capability of this system was validate by few
series of testing, which conducted at standard 36m3 office room.
Result of the testing found that 0.1 m3 of chill water is able to
maintain the room temperature within standard up to 4 ~ 8 hours. It
expected able to maintain room temperature up to 10 hour with some
improvement.
Abstract: Ionanofluids are a new and innovative class of heat transfer fluids which exhibit fascinating thermophysical properties compared to their base ionic liquids. This paper deals with the findings of thermal conductivity and specific heat capacity of ionanofluids as a function of a temperature and concentration of nanotubes. Simulation results using ionanofluids as coolants in heat exchanger are also used to access their feasibility and performance in heat transfer devices. Results on thermal conductivity and heat capacity of ionanofluids as well as the estimation of heat transfer areas for ionanofluids and ionic liquids in a model shell and tube heat exchanger reveal that ionanofluids possess superior thermal conductivity and heat capacity and require considerably less heat transfer areas as compared to those of their base ionic liquids. This novel class of fluids shows great potential for advanced heat transfer applications.
Abstract: One of the methods for detecting the target position
error in the laser tracking systems is using Four Quadrant (4Q)
detectors. If the coordinates of the target center is yielded through the
usual relations of the detector outputs, the results will be nonlinear,
dependent on the shape, target size and its position on the detector
screen. In this paper we have designed an algorithm with using
neural network that coordinates of the target center in laser tracking
systems is calculated by using detector outputs obtained from visual
modeling. With this method, the results except from the part related
to the detector intrinsic limitation, are linear and dependent from the
shape and target size.
Abstract: More and more natural disasters are happening every
year: floods, earthquakes, volcanic eruptions, etc. In order to reduce
the risk of possible damages, governments all around the world are
investing into development of Early Warning Systems (EWS) for
environmental applications. The most important task of the EWS is
identification of the onset of critical situations affecting environment
and population, early enough to inform the authorities and general
public. This paper describes an approach for monitoring of flood
protections systems based on machine learning methods. An
Artificial Intelligence (AI) component has been developed for
detection of abnormal dike behaviour. The AI module has been
integrated into an EWS platform of the UrbanFlood project (EU
Seventh Framework Programme) and validated on real-time
measurements from the sensors installed in a dike.
Abstract: This study compared socio-economic status attainment between the Muslim and Santal couples in rural Bangladesh. For this we hypothesized that socio-economic status attainment (occupation, education and income) of the Muslim couples was higher than the Santal ones in rural Bangladesh. In order to examine the hypothesis 288 couples (145 couples for Muslim and 143 couples for Santal) selected by cluster random sampling from Kalna village, Bangladesh were individually interviewed with semistructured questionnaire method. The results of Pearson Chi-Squire test suggest that there were significant differences in socio-economic status attainment between the two communities- couples. In addition, Pearson correlation coefficients also suggest that there were significant associations between the socio-economic statuses attained by the two communities- couples in rural Bangladesh. Further crosscultural study should conduct on how inter-community relations in rural social structure of Bangladesh influence the differences among the couples- socio-economic status attainment
Abstract: In this paper, a field oriented control (FOC) induction motor drive is presented. In order to eliminate the speed sensor, an adaptation algorithm for tuning the rotor speed is proposed. Based on the Model Reference Adaptive System (MRAS) scheme, the rotor speed is tuned to obtain an exact FOC induction motor drive. The reference and adjustable models, developed in stationary stator reference frame, are used in the MRAS scheme to estimate induction rotor speed from measured terminal voltages and currents. The Integral Proportional (IP) gains speed controller are tuned by a modern approach that is the Particle Swarm Optimization (PSO) algorithm in order to optimize the parameters of the IP controller. The use of PSO as an optimization algorithm makes the drive robust, with faster dynamic response, higher accuracy and insensitive to load variation. The proposed algorithm has been tested by numerical simulation, showing the capability of driving load.
Abstract: Software Architecture plays a key role in software development but absence of formal description of Software Architecture causes different impede in software development. To cope with these difficulties, ontology has been used as artifact. This paper proposes ontology for Software Architectural design based on IEEE model for architecture description and Kruchten 4+1 model for viewpoints classification. For categorization of style and views, ISO/IEC 42010 has been used. Corpus method has been used to evaluate ontology. The main aim of the proposed ontology is to classify and locate Software Architectural design information.
Abstract: There are many views on how human decision makers behave. In this work, the Justices of the United States Supreme Court will be viewed in terms of constrained maximization and cognitivecybernetic theory. This paper will integrate research in such fields as law, political science, psychology, economics and decision making theory. It will be argued that due to its heavy workload, the Supreme Court is forced to make decisions in a boundedly rational manner. The ideas and theory put forward here will be tested in the area of the Court’s decisions involving religion. Therefore, the cases involving the U.S. Constitution’s Free Exercise Clause and Establishment Clause will be analyzed. Also, variables such as the U.S. government’s involvement in these cases will be considered. The years to be studied will be 1987-2011.
Abstract: Equal Channel Angular Pressing (ECAP) is currently
being widely investigated because of its potential to produce ultrafine
grained microstructures in metals and alloys. A sound
knowledge of the plastic deformation and strain distribution is
necessary for understanding the relationships between strain
inhomogeneity and die geometry. Considerable research has been
reported on finite element analysis of this process, assuming threedimensional
plane strain condition. However, the two-dimensional
models are not suitable due to the geometry of the dies, especially in
cylindrical ones. In the present work, three-dimensional simulation of
ECAP process was carried out for six outer corner radii (sharp to 10
mm in steps of 2 mm), with channel angle 105¶Çü▒, for strain hardening
aluminium alloy (AA 6101) using ABAQUS/Standard software.
Strain inhomogeneity is presented and discussed for all cases. Pattern
of strain variation along selected radial lines in the body of the workpiece
is presented. It is found from the results that the outer corner
has a significant influence on the strain distribution in the body of
work-piece. Based on inhomogeneity and average strain criteria,
there is an optimum outer corner radius.
Abstract: This paper shows the potential system benefits of
simple tracking solar system using a stepper motor and light sensor.
This method is increasing power collection efficiency by developing
a device that tracks the sun to keep the panel at a right angle to its
rays. A solar tracking system is designed, implemented and
experimentally tested. The design details and the experimental results
are shown.
Abstract: This study offers a new simple method for assessing
an axial part-through crack in a pipe wall. The method utilizes simple
approximate expressions for determining the fracture parameters K,
J, and employs these parameters to determine critical dimensions of a
crack on the basis of equality between the J-integral and the J-based
fracture toughness of the pipe steel. The crack tip constraint is taken
into account by the so-called plastic constraint factor C, by which the
uniaxial yield stress in the J-integral equation is multiplied. The
results of the prediction of the fracture condition are verified by burst
tests on test pipes.
Abstract: An algorithm for learning an overcomplete dictionary
using a Cauchy mixture model for sparse decomposition of an underdetermined
mixing system is introduced. The mixture density
function is derived from a ratio sample of the observed mixture
signals where 1) there are at least two but not necessarily more
mixture signals observed, 2) the source signals are statistically
independent and 3) the sources are sparse. The basis vectors of the
dictionary are learned via the optimization of the location parameters
of the Cauchy mixture components, which is shown to be more
accurate and robust than the conventional data mining methods
usually employed for this task. Using a well known sparse
decomposition algorithm, we extract three speech signals from two
mixtures based on the estimated dictionary. Further tests with
additive Gaussian noise are used to demonstrate the proposed
algorithm-s robustness to outliers.
Abstract: Performance management seems to be essential in
business area and is also an exciting topic. Despite significant and
myriads of research efforts, performance management guide today as a
rigorous approach is still in an immature state and metrics are often
selected based on intuitive and heuristic approach. In R&D side, the
difficulty to guide the proper performance management is even more
increasing due to the natural characteristics of R&D such as unique or
domain-specific problems. In our approach, we present R&D
performance management guide considering various characteristics of
R&D side: performance evaluation objectives, dimensions, metrics,
and uncertainties of R&D sector.
Abstract: A renewable energy system discussed in this paper is
a stand-alone wind-hydrogen system for a remote island in Australia.
The analysis of an existing wind-diesel power system was performed.
Simulation technique was used to model the power system currently
employed on the island, and simulated different configurations of
additional hydrogen energy system. This study aims to determine the
suitable hydrogen integrated configuration to setting up the prototype
system for the island, which helps to reduce the diesel consumption
on the island. A set of configurations for the hydrogen system and
associated parameters that consists of wind turbines, electrolysers,
hydrogen internal combustion engines, and storage tanks has been
purposed. The simulation analyses various configurations that
perfectly balances the system to meet the demand on the island.
Abstract: Optical networks are high capacity networks that meet
the rapidly growing demand for bandwidth in the terrestrial
telecommunications industry. This paper studies and evaluates singlemode
and multimode fiber transmission by varying the distance. It
focuses on their performance in LAN environment. This is achieved
by observing the pulse spreading and attenuation in optical spectrum
and eye-diagram that are obtained using OptSim simulator. The
behaviors of two modes with different distance of data transmission
are studied, evaluated and compared.
Abstract: This paper aims to fabricated high quality anodic
aluminum oxide (AAO) film by anodization method. AAO pore size,
pore density, and film thickness can be controlled in 10~500 nm,
108~1011 pore．cm-2, and 1~100 μm. AAO volume and surface area can
be computed based on structural parameters such as thickness, pore
size, pore density, and sample size. Base on the thetorical calculation,
AAO has 100 μm thickness with 15 nm, 60 nm, and 500 nm pore
diameters AAO surface areas are 1225.2 cm2, 3204.4 cm2, and 549.7
cm2, respectively. The large unit surface area which is useful for
adsorption application. When AAO adsorbed pH indictor of
bromphenol blue presented a sensitive pH detection of solution
change. This testing method can further be used for the precise
measurement of biotechnology, convenience measurement of
industrial engineering.
Abstract: A business case is a proposal for an investment
initiative to satisfy business and functional requirements. The
business case provides the foundation for tactical decision making
and technology risk management. It helps to clarify how the
organization will use its resources in the best way by providing
justification for investment of resources. This paper describes how
simulation was used for business case benefits and return on
investment for the procurement of 8 production machines. With
investment costs of about 4.7 million dollars and annual operating
costs of about 1.3 million, we needed to determine if the machines
would provide enough cost savings and cost avoidance. We
constructed a model of the existing factory environment consisting of
8 machines and subsequently, we conducted average day simulations
with light and heavy volumes to facilitate planning decisions
required to be documented and substantiated in the business case.