Abstract: The automatic discrimination of seismic signals is an important practical goal for earth-science observatories due to the large amount of information that they receive continuously. An essential discrimination task is to allocate the incoming signal to a group associated with the kind of physical phenomena producing it. In this paper, two classes of seismic signals recorded routinely in geophysical laboratory of the National Center for Scientific and Technical Research in Morocco are considered. They correspond to signals associated to local earthquakes and chemical explosions. The approach adopted for the development of an automatic discrimination system is a modular system composed by three blocs: 1) Representation, 2) Dimensionality reduction and 3) Classification. The originality of our work consists in the use of a new wavelet called "modified Mexican hat wavelet" in the representation stage. For the dimensionality reduction, we propose a new algorithm based on the random projection and the principal component analysis.
Abstract: This paper proposes an application of the differential
evolution (DE) algorithm for solving the economic dispatch problem
(ED). Furthermore, the regenerating population procedure added to
the conventional DE in order to improve escaping the local minimum
solution. To test performance of DE algorithm, three thermal
generating units with valve-point loading effects is used for testing.
Moreover, investigating the DE parameters is presented. The
simulation results show that the DE algorithm, which had been
adjusted parameters, is better convergent time than other optimization
methods.
Abstract: The information systems with incomplete attribute
values and fuzzy decisions commonly exist in practical problems. On
the base of the notion of variable precision rough set model for
incomplete information system and the rough set model for
incomplete and fuzzy decision information system, the variable rough
set model for incomplete and fuzzy decision information system is
constructed, which is the generalization of the variable precision
rough set model for incomplete information system and that of rough
set model for incomplete and fuzzy decision information system. The
knowledge reduction and heuristic algorithm, built on the method and
theory of precision reduction, are proposed.
Abstract: The Mahin area is a part of Tarom- Hashtjin zone that
located in west of Qazvin province in northwest of Iran. Many copper
and base metals ore deposits are hosted by this zone. High potential
localities identification in this area is very necessary. The objective of
this research, is finding hydrothermal alteration zones by remote
sensing methods and best processing technique of Advanced
Spaceborne Thermal Emission and Reflection Radiometer (ASTER)
data. Different methods such as band ratio, Principal Component
Analysis (PCA), Minimum Noise Fraction (MNF) and Least Square
Fit (LS-Fit) were used for mapping hydrothermal alteration zones.
Abstract: This research presents the development of simulation
modeling for WIP management in semiconductor fabrication.
Manufacturing simulation modeling is needed for productivity
optimization analysis due to the complex process flows involved
more than 35 percent re-entrance processing steps more than 15 times
at same equipment. Furthermore, semiconductor fabrication required
to produce high product mixed with total processing steps varies from
300 to 800 steps and cycle time between 30 to 70 days. Besides the
complexity, expansive wafer cost that potentially impact the
company profits margin once miss due date is another motivation to
explore options to experiment any analysis using simulation
modeling. In this paper, the simulation model is developed using
existing commercial software platform AutoSched AP, with
customized integration with Manufacturing Execution Systems
(MES) and Advanced Productivity Family (APF) for data collections
used to configure the model parameters and data source. Model
parameters such as processing steps cycle time, equipment
performance, handling time, efficiency of operator are collected
through this customization. Once the parameters are validated, few
customizations are made to ensure the prior model is executed. The
accuracy for the simulation model is validated with the actual output
per day for all equipments. The comparison analysis from result of
the simulation model compared to actual for achieved 95 percent
accuracy for 30 days. This model later was used to perform various
what if analysis to understand impacts on cycle time and overall
output. By using this simulation model, complex manufacturing
environment like semiconductor fabrication (fab) now have
alternative source of validation for any new requirements impact
analysis.
Abstract: Traffic flow in adverse weather conditions have been investigated in this study for general traffic, week day and week end traffic. The empirical evidence is strong in support of the view that rainfall affects macroscopic traffic flow parameters. Data generated from a basic highway section along J5 in Johor Bahru, Malaysia was synchronized with 161 rain events over a period of three months. This revealed a 4.90%, 6.60% and 11.32% reduction in speed for light rain, moderate rain and heavy rain conditions respectively. The corresponding capacity reductions in the three rainfall regimes are 1.08% for light rain, 6.27% for moderate rain and 29.25% for heavy rain. In the week day traffic, speed drops of 8.1% and 16.05% were observed for light and heavy conditions. The moderate rain condition speed increased by 12.6%. The capacity drops for week day traffic are 4.40% for light rain, 9.77% for moderate rain and 45.90% for heavy rain. The weekend traffic indicated speed difference between the dry condition and the three rainy conditions as 6.70% for light rain, 8.90% for moderate rain and 13.10% for heavy rain. The capacity changes computed for the weekend traffic were 0.20% in light rain, 13.90% in moderate rain and 16.70% in heavy rain. No traffic instabilities were observed throughout the observation period and the capacities reported for each rain condition were below the norain condition capacity. Rainfall has tremendous impact on traffic flow and this may have implications for shock wave propagation.
Abstract: In this study, the kinetic of biogas production was studied by performing a series laboratory experiment using rumen fluid of animal ruminant as inoculums. Cattle manure as substrate was inoculated by rumen fluid to the anaerobic biodigester. Laboratory experiments using 400 ml biodigester were performed in batch operation mode. Given 100 grams of fresh cattle manure was fed to each biodigester and mixed with rumen fluid by manure : rumen weight ratio of 1:1 (MR11). The operating temperatures were varied at room temperature and 38.5 oC. The cumulative volume of biogas produced was used to measure the biodigester performance. The research showed that the rumen fluid inoculated to biodigester gave significant effect to biogas production (P
Abstract: Ant colony optimization (ACO) and its variants are
applied extensively to resolve various continuous optimization
problems. As per the various diversification and intensification
schemes of ACO for continuous function optimization, researchers
generally consider components of multidimensional state space to
generate the new search point(s). However, diversifying to a new
search space by updating only components of the multidimensional
vector may not ensure that the new point is at a significant distance
from the current solution. If a minimum distance is not ensured
during diversification, then there is always a possibility that the
search will end up with reaching only local optimum. Therefore, to
overcome such situations, a Mahalanobis distance-based
diversification with Nelder-Mead simplex-based search scheme for
each ant is proposed for the ACO strategy. A comparative
computational run results, based on nine nonlinear standard test
problems, confirms that the performance of ACO is improved
significantly with the integration of the proposed schemes in the
ACO.
Abstract: Fractional Fourier Transform, which is a
generalization of the classical Fourier Transform, is a powerful tool
for the analysis of transient signals. The discrete Fractional Fourier
Transform Hamiltonians have been proposed in the past with varying
degrees of correlation between their eigenvectors and Hermite
Gaussian functions. In this paper, we propose a new Hamiltonian for
the discrete Fractional Fourier Transform and show that the
eigenvectors of the proposed matrix has a higher degree of
correlation with the Hermite Gaussian functions. Also, the proposed
matrix is shown to give better Fractional Fourier responses with
various transform orders for different signals.
Abstract: Corporate social responsibility (CSR) viewpoint have challenged the traditional perception to understand corporations position. Production- and managerial-centred views are expanding towards reference group-centred policies. Consequently, the significance of new kind of knowledge has emerged. In addition to management of the organisation, the idea of CSR emphasises the importance to recognise the value-expectations of operational environment. It is know that management is often well-aware of corporate social responsibilities, but it is less clear how well these high level goals are understood in practical product design and development work. In this study, the apprehension above proved to be real to some degree. While management was very aware of CSR it was less familiar to designers. The outcome shows that it is essential to raise ethical values and issues higher in corporate communication, if it is wished that they materialize also in products.
Abstract: Landfill gas, particularly methane is one of the
greenhouse gases which contributes to global warming. This paper presents the findings of a study on methane gas production from
simulated landfill reactor under saturated conditions. A reactor was constructed to represent a landfill cell of 2.5 m thickness on sandy
soil. The reactor was 0.2 m in diameter and 4 m in height. One meter of sand and pebble layer was packed at the bottom of the reactor
followed by 2.5 m of solid waste layer and 0.4 m of sand layer as the cover soil. Degradation of waste in the solid waste layer was at
acidification stage as indicated by the leachate quality with COD as
high as 55,511 mg/L and pH as low as 5.1. However, methanogenic
environment was established at the bottom sand layer after one year of operation indicated by pH of 7.2 and methane gas generation.
Leachate degradation took place as the leachate moved through the
sand layer at an infiltration of rate 0.7 cm/day. This resulted in landfill gas production of 77 mL/day/kg containing 55 to 65% methane. The application of sand layer contributed to the gas
production from landfill by an in-situ degradation of leachate in the
sand at the bottom of the landfill.
Abstract: This study presents an active vibration control
technique to reduce the earthquake responses of a retained structural
system. The proposed technique is a synthesis of the adaptive input
estimation method (AIEM) and linear quadratic Gaussian (LQG)
controller. The AIEM can estimate an unknown system input online.
The LQG controller offers optimal control forces to suppress
wall-structural system vibration. The numerical results show robust
performance in the active vibration control technique.
Abstract: Due to heightened concerns over environmental and economic issues the growing important of air pollution, and the importance of conserving fossil fuel resources in the world, the automotive industry is now forced to produce more fuel efficient, low emission vehicles and new drive system technologies. One of the most promising technologies to receive attention is the hybrid electric vehicle (HEV), which consists of two or more energy sources that supply energy to electric traction motors that in turn drive the wheels. This paper presents the various structures of HEV systems, the basic theoretical knowledge for describing their operation and the general behaviour of the HEV in acceleration, cruise and deceleration phases. The conventional design and sizing of a series HEV is studied. A conventional bus and its series configuration are defined and evaluated using the ADVISOR. In this section the simulation of a standard driving cycle and prediction of its fuel consumption and emissions of the HEV are discussed. Finally the bus performance is investigated to establish whether it can satisfy the performance, fuel consumption and emissions requested. The validity of the simulation has been established by the close conformity between the fuel consumption of the conventional bus reported by the manufacturer to what has achieved from the simulation.
Abstract: In literature, there are metrics for identifying the
quality of reusable components but the framework that makes use of
these metrics to precisely predict reusability of software components
is still need to be worked out. These reusability metrics if identified
in the design phase or even in the coding phase can help us to reduce
the rework by improving quality of reuse of the software component
and hence improve the productivity due to probabilistic increase in
the reuse level. As CK metric suit is most widely used metrics for
extraction of structural features of an object oriented (OO) software;
So, in this study, tuned CK metric suit i.e. WMC, DIT, NOC, CBO
and LCOM, is used to obtain the structural analysis of OO-based
software components. An algorithm has been proposed in which the
inputs can be given to K-Means Clustering system in form of
tuned values of the OO software component and decision tree is
formed for the 10-fold cross validation of data to evaluate the in
terms of linguistic reusability value of the component. The developed
reusability model has produced high precision results as desired.
Abstract: In this study, the Scots pine (Pinus sylvestris L.) C
needles (i.e. the current-year-needles) were used as bioindicators in
determining the aerial distribution pattern of sulphur emissions
around industrial point sources at Kemi, Northern Finland. The
average sulphur concentration in the C needles was 897 mg/kg
(d.w.), with a standard deviation of 118 mg/kg (d.w.) and range 740 –
1350 mg/kg (d.w.). According to results in this study, Scots pine
needles (Pinus sylvestris L.) appear to be an ideal bioindicators for
identifying atmospheric sulphur pollution derived from industrial
plants and can complement the information provided by plant
mapping studies around industrial plants.
Abstract: Multicarrier transmission system such as Orthogonal
Frequency Division Multiplexing (OFDM) is a promising technique
for high bit rate transmission in wireless communication system.
OFDM is a spectrally efficient modulation technique that can achieve
high speed data transmission over multipath fading channels without
the need for powerful equalization techniques. However the price
paid for this high spectral efficiency and less intensive equalization
is low power efficiency. OFDM signals are very sensitive to nonlinear
effects due to the high Peak-to-Average Power Ratio (PAPR),
which leads to the power inefficiency in the RF section of the
transmitter. This paper investigates the effect of PAPR reduction on
the performance parameter of multicarrier communication system.
Performance parameters considered are power consumption of Power
Amplifier (PA) and Digital-to-Analog Converter (DAC), power amplifier
efficiency, SNR of DAC and BER performance of the system.
From our analysis it is found that irrespective of PAPR reduction
technique being employed, the power consumption of PA and DAC
reduces and power amplifier efficiency increases due to reduction in
PAPR. Moreover, it has been shown that for a given BER performance
the requirement of Input-Backoff (IBO) reduces with reduction in
PAPR.
Abstract: A measurement system for pH array sensors is
introduced to increase accuracy, and decrease non-ideal effects
successfully. An array readout circuit reads eight potentiometric
signals at the same time, and obtains an average value. The deviation
value or the extreme value is counteracted and the output voltage is a
relatively stable value. The errors of measuring pH buffer solutions are
decreased obviously with this measurement system, and the non-ideal
effects, drift and hysteresis, are lowered to 1.638mV/hr and 1.118mV,
respectively. The efficiency and stability are better than single sensor.
The whole sensing characteristics are improved.
Abstract: In this paper, the construction of a detailed spine
model is presented using the LifeMOD Biomechanics Modeler. The
detailed spine model is obtained by refining spine segments in
cervical, thoracic and lumbar regions into individual vertebra
segments, using bushing elements representing the intervertebral
discs, and building various ligamentous soft tissues between
vertebrae. In the sagittal plane of the spine, constant force will be
applied from the posterior to anterior during simulation to determine
dynamic characteristics of the spine. The force magnitude is
gradually increased in subsequent simulations. Based on these
recorded dynamic properties, graphs of displacement-force
relationships will be established in terms of polynomial functions by
using the least-squares method and imported into a haptic integrated
graphic environment. A thoracolumbar spine model with complex
geometry of vertebrae, which is digitized from a resin spine
prototype, will be utilized in this environment. By using the haptic
technique, surgeons can touch as well as apply forces to the spine
model through haptic devices to observe the locomotion of the spine
which is computed from the displacement-force relationship graphs.
This current study provides a preliminary picture of our ongoing
work towards building and simulating bio-fidelity scoliotic spine
models in a haptic integrated graphic environment whose dynamic
properties are obtained from LifeMOD. These models can be helpful
for surgeons to examine kinematic behaviors of scoliotic spines and
to propose possible surgical plans before spine correction operations.
Abstract: Safety Critical hard Real-Time Systems are ever
present in the avionics industry. The Model Driven Architecture
(MDA) offers different levels of model abstraction and generation.
This paper discusses our concerns relating to model development and
generation when using the MDA approach in the avionics industry.
These concerns are based on our experience when looking into
adopting the MDA as part of avionics systems development. We
place emphasis on transformations between model types and discuss
possible benefits of adopting an MDA approach as part of the
software development life cycle.
Abstract: This paper presents a procedure of forming the
mathematical model of radial electric power systems for simulation
of both transient and steady-state conditions. The research idea has
been based on nodal voltages technique and on differentiation of
Kirchhoff's current law (KCL) applied to each non-reference node of
the radial system, the result of which the nodal voltages has been
calculated by solving a system of algebraic equations. Currents of the
electric power system components have been determined by solving
their respective differential equations. Transforming the three-phase
coordinate system into Cartesian coordinate system in the model
decreased the overall number of equations by one third. The use of
Cartesian coordinate system does not ignore the DC component
during transient conditions, but restricts the model's implementation
for symmetrical modes of operation only. An example of the input
data for a four-bus radial electric power system has been calculated.