Abstract: Different services based on different switching
techniques in wireless networks leads to drastic changes in the
properties of network traffic. Because of these diversities in services,
network traffic is expected to undergo qualitative and quantitative
variations. Hence, assumption of traffic characteristics and the
prediction of network events become more complex for the wireless
networks. In this paper, the traffic characteristics have been studied
by collecting traces from the mobile switching centre (MSC). The
traces include initiation and termination time, originating node, home
station id, foreign station id. Traffic parameters namely, call interarrival
and holding times were estimated statistically. The results
show that call inter-arrival and distribution time in this wireless
network is heavy-tailed and follow gamma distributions. They are
asymptotically long-range dependent. It is also found that the call
holding times are best fitted with lognormal distribution. Based on
these observations, an analytical model for performance estimation is
also proposed.
Abstract: In this paper a scheme is proposed for generating
a programmable current reference which can be implemented
in the CMOS technology. The current can be varied over a
wide range by changing an external voltage applied to one
of the control gates of FGMOS (Floating Gate MOSFET).
For a range of supply voltages and temperature, CMOS
current reference is found to be dependent, this dependence
is compensated by subtracting two current outputs with the
same dependencies on the supply voltage and temperature.
The system performance is found to improve with the
use of FGMOS. Mathematical analysis of the proposed
circuit is done to establish supply voltage and temperature
independence. Simulation and performance evaluation of the
proposed current reference circuit is done using TANNER
EDA Tools. The current reference shows the supply and
temperature dependencies of 520 ppm/V and 312 ppm/oC,
respectively. The proposed current reference can operate down
to 0.9 V supply.
Abstract: In this paper, numerical solution of system of
Fredholm and Volterra integral equations by means of the Spline
collocation method is considered. This approximation reduces the
system of integral equations to an explicit system of algebraic
equations. The solution is collocated by cubic B-spline and the
integrand is approximated by the Newton-Cotes formula. The error
analysis of proposed numerical method is studied theoretically. The
results are compared with the results obtained by other methods to
illustrate the accuracy and the implementation of our method.
Abstract: The objective of this study is to analyze the
prophylactic usage of low molecular weight heparin (LMWH) along
pregnancy and the correlation between their usage and month/week
of pregnancy, in the Department of Gynecology and Obstetrics, at
Clinical Hospital in Tetovo. A retrospective study was undertaken
during 01 January – 31 December 2012. Over of one year, the total
number of patients was 4636. Among the 1447 (32.21%) pregnant
women, 298 (20.59%) of them were prescribed LMWH. The majority
of patients given LMWH, 119 (39.93%) were diagnosed
hypercoagulable. The age group with the highest attendance was 25-
35, 141 patients (47.32%). For 195 (65.44%) patients, this was their
first pregnancy. Earliest stage of using LMWH was the second month
of pregnancy 4 (1.34%) cases. The most common patients were 70
women along the seventh month (23.49%), followed by 68 in the
ninth month of pregnancy (22.81%). Women in the 28th gestational
week, were found to be the most affected, a total of 55 (78.57%) were
in that week. Clexane 2000 and Fraxiparine 0.3 were the most
common for which low molecular weight heparin was prescribed.
The number of patients which received Clexane 2000 was 84
(28.19%), followed by those with Fraxiparine 0.3 81 (27.18%). The
administration of LMWH is associated with long hospitalization
(median 14,6 days).
Abstract: Since the emergence of e-Commerce, the world of
business has witnessed a radical shift in the way business activities
are conducted. However, the emergence of m-Commerce has further
pushed the boundaries of virtual commerce revolution. As a result,
there seems to be a growing blur in the distinction between e-
Commerce and m-Commerce. In addition, existing definitions for
both forms of commerce highlight characteristics (e.g. type of device
and activity conducted) that may be applicable to both concepts. The
aim of this paper is to identify the characteristics that help define and
delineate between e- and m- Commerce. The paper concludes that
characteristics of mobility, ubiquity and immediacy provide a clearer
and simpler template to distinguish between e-Commerce and m-
Commerce.
Abstract: In this paper family of multilevel inverter topology
with reduced number of power switches is presented. The proposed
inverter can generate both even and odd level. The proposed topology
is suitable for symmetric structure. The proposed symmetric inverter
results in reduction of power switches, power diode and gate driver
circuits and also it may further minimize the installation area and
cost. To prove the superiority of proposed topology is compared with
conventional topologies. The performance of this symmetric
multilevel inverter has been tested by computer based simulation and
prototype based experimental setup for nine-level inverter is
developed and results are verified.
Abstract: The asynchronous discussion forum is one of the most
widely used activities in learning management system environment.
Online forum allows participants to interact, construct knowledge,
and can be used to complement face to face sessions in blended
learning courses. However, to what extent do the students perceive
the benefits or advantages of forum remain to be seen. Through
content and social network analyses, instructors will be able to gauge
the students’ engagement and knowledge construction level. Thus,
this study aims to analyze the students’ level of knowledge
construction and their participation level that occur through online
discussion. It also attempts to investigate the relationship between the
level of knowledge construction and their social interaction patterns.
The sample involves 23 students undertaking a master course in one
public university in Malaysia. The asynchronous discussion forum
was conducted for three weeks as part of the course requirement. The
finding indicates that the level of knowledge construction is quite
low. Also, the density value of 0.11 indicating the overall
communication among the participants in the forum is low. This
study reveals that strong and significant correlations between SNA
measures (in-degree centrality, out-degree centrality) and level of
knowledge construction. Thus, allocating these active students in
different group aids the interactive discussion takes place. Finally,
based upon the findings, some recommendations to increase students’
level of knowledge construction and also for further research are
proposed.
Abstract: Lately, asynchronous discussion forum is integrated in
higher educational institutions as it may increase learning process,
learners’ understanding, achievement and knowledge construction.
The asynchronous discussion forum is used to complement the
traditional, face-to-face learning session in hybrid learning courses.
However, studies have proven that students’ engagement in online
forums is still unconvincing. Thus, the aim of this study is to
investigate the motivating factors and obstacles that affect the
learners’ engagement in asynchronous discussion forum. This study
is carried out in one of the public higher educational institutions in
Malaysia with 18 postgraduate students as samples. The authors have
developed a 40-items questionnaire based on literature review. The
results indicate several factors that have encouraged or limited
students’ engagement in asynchronous discussion forum: (a) the
practices or behaviors of peers, or instructors, (b) the needs for the
discussions, (c) the learners’ personalities, (d) constraints in
continuing the discussion forum, (e) lack of ideas, (f) the level of
thoughts, (g) the level of knowledge construction, (h) technical
problems, (i) time constraints and (j) misunderstanding. This study
suggests some recommendations to increase the students’
engagement in online forums. Finally, based upon the findings, some
implications are proposed for further research.
Abstract: Cloud service brokering is a new service paradigm that
provides interoperability and portability of application across multiple
Cloud providers. In this paper, we designed Cloud service brokerage
system, anyBroker, supporting integrated service provisioning and
SLA based service lifecycle management. For the system design, we
introduce the system concept and whole architecture, details of main
components and use cases of primary operations in the system. These
features ease the Cloud service provider and customer’s concern and
support new Cloud service open market to increase Cloud service
profit and prompt Cloud service echo system in Cloud computing
related area.
Abstract: This paper presents the design analysis of saddle
support of a horizontal pressure vessel. Since saddle have the vital
role to support the pressure vessel and to maintain its stability, it
should be designed in such a way that it can afford the vessel load
and internal pressure of the vessel due to liquid contained in the
vessel. A model of horizontal pressure vessel and saddle support is
created in ANSYS. Stresses are calculated using mathematical
approach and ANSYS software. The analysis reveals the zone of high
localized stress at the junction part of the pressure vessel and saddle
support due to operating conditions. The results obtained by both the
methods are compared with allowable stress value for safe designing.
Abstract: Most quality models have defined usability as a
significant factor that leads to improving product acceptability,
increasing user satisfaction, improving product reliability, and also
financially benefitting companies. Usability is also the best factor that
balances both the technical and human aspects of a software product,
which is an important aspect in defining quality during software
development process. A usability risk consist risk factors that could
impact the usability of a software product thereby contributing to
negative user experiences and causing a possible software product
failure. Hence, it is important to mitigate and reduce usability risks in
the software development process itself. By managing possible
usability risks in software development process, failure of software
product could be reduced. Therefore, this research uses the Delphi
method to identify mitigation plans for reducing potential usability
risks. The Delphi method is conducted with seven experts from the
field of risk management and software development.
Abstract: The purpose of this project is to carry out an analysis
and determine the profile of actual lean manufacturing processes in
the Metropolitan Area of Bucaramanga. Through the analysis of
qualitative and quantitative variables it was possible to establish how
these manufacturers develop production practices that ensure their
competitiveness and productivity in the market.
In this study, a random sample of metallurgic and wrought iron
companies was applied, following which a quantitative focus and
analysis was used to formulate a qualitative methodology for
measuring the level of lean manufacturing procedures in the industry.
A qualitative evaluation was also carried out through a multivariate
analysis using the Numerical Taxonomy System (NTSYS) program
which should allow for the determination of Lean Manufacturing
profiles.
Through the results it was possible to observe how the companies
in the sector are doing with respect to Lean Manufacturing Practices,
as well as identify the level of management that these companies
practice with respect to this topic. In addition, it was possible to
ascertain that there is no one dominant profile in the sector when it
comes to Lean Manufacturing.
It was established that the companies in the metallurgic and
wrought iron industry show low levels of Lean Manufacturing
implementation. Each one carries out diverse actions that are
insufficient to consolidate a sectoral strategy for developing a
competitive advantage which enables them to tie together a
production strategy.
Abstract: Stress Corrosion Crack (SCC) in pipeline is a type of
environmentally assisted cracking (EAC), since its discovery in 1965
as a possible cause of failure in pipeline, SCC has caused, on
average, one of two failures per year in the U.S, According to the
NACE SCC DA a pipe line segment is considered susceptible to SCC
if all of the following factors are met: The operating stress exceeds
60% of specified minimum yield strength (SMYS), the operating
temperature exceeds 38°C, the segment is less than 32 km
downstream from a compressor station, the age of the pipeline is
greater than 10 years and the coating type is other than Fusion
Bonded Epoxy(FBE). In this paper as a practical experience in
NISOC, Direct Assessment (DA) Method is used for identification
SCC defect in unpiggable pipeline located downstream of
compressor station.
Abstract: Kuosheng nuclear power plant (NPP) is a BWR/6 type
NPP and located on the northern coast of Taiwan. First, Kuosheng
NPP TRACE model were developed in this research. In order to assess
the system response of Kuosheng NPP TRACE model, startup tests
data were used to evaluate Kuosheng NPP TRACE model. Second, the
overpressurization transient analysis of Kuosheng NPP TRACE model
was performed. Besides, in order to confirm the mechanical property
and integrity of fuel rods, FRAPTRAN analysis was also performed in
this study.
Abstract: Bone properties and response behavior after static or
dynamic activation (loading) are still interesting topics in many fields
of the science especially in the biomechanical problems such as bone
loss of astronauts in space, osteoporosis, bone remodeling after
fracture or remodeling after surgery (endoprosthesis and implants)
and in osteointegration. This contribution deals with the relation
between physiological, demineralized and deproteinized state of the
turkey long bone – tibia. Three methods for comparison were used: 1)
densitometry, 2) three point bending and 3) frequency analysis. The
main goal of this work was to describe the decrease of the protein
(collagen) or mineral of the bone with relation to the fracture in three
point bending. The comparison is linked to the problem of different
bone mechanical behavior in physiological and osteoporotic state.
Abstract: The global solved problem is the calculation of the
parameters of ceramic material from a set of destruction tests of
ceramic heads of total hip joint endoprosthesis. The standard way of
calculation of the material parameters consists in carrying out a set of
3 or 4 point bending tests of specimens cut out from parts of the
ceramic material to be analysed. In case of ceramic heads, it is not
possible to cut out specimens of required dimensions because the
heads are too small (if the cut out specimens were smaller than the
normalised ones, the material parameters derived from them would
exhibit higher strength values than those which the given ceramic
material really has). A special destruction device for heads
destruction was designed and the solved local problem is the
modification of this destructive device based on the analysis of
tensile stress in the head for two different values of the depth of the
conical hole in the head. The goal of device modification is a shift of
the location with extreme value of σ1max from the region of head’s
hole bottom to its opening. This modification will increase the
credibility of the obtained material properties of bioceramics, which
will be determined from a set of head destructions using the Weibull
weakest link theory.
Abstract: A noble low NOx combustion technology, based on
partial oxidation combustion concept in a fuel rich combustion zone, is
successfully applied in this research. The burner is designed such that
a portion of fuel is heated and pre-vaporized in the furnace then
injected into a fuel rich combustion zone so that a partial oxidation
reaction occurs. The effects of equivalence ratio, thermal load, and
fuel distribution ratio on the emissions of NOx and CO are
experimentally investigated. This newly developed combustion
technology showed very low NOx emission level, about 12 ppm, when
light oil is used as a fuel.
Abstract: Folic acid (FA) is known to be an important
supplement to prevent neural tube defect (NTD) in pregnant women.
Similar to some commercial formulations, sodium bicarbonate
solution is used as a solvent for FA. This work uses the antisolvent
vapour precipitation (AVP), incorporating ethanol vapour as the
convective drying medium in place of air to produce branch-like
micro-structure FA particles. Interestingly, the dissolution rate of the
resultant particle is 2-3 times better than the particle produce from
conventional air drying due to the higher surface area of particles
produced. The higher dissolution rate could possibly improve the
delivery and absorption of FA in human body. This application could
potentially be extended to other commercial products, particularly in
less soluble drugs to improve its solubility.
Abstract: The North-eastern part of India, which receives
heavier rainfall than other parts of the subcontinent, is of great
concern now-a-days with regard to climate change. High intensity
rainfall for short duration and longer dry spell, occurring due to
impact of climate change, affects river morphology too. In the present
study, an attempt is made to delineate the North-eastern region of
India into some homogeneous clusters based on the Fuzzy Clustering
concept and to compare the resulting clusters obtained by using
conventional methods and nonconventional methods of clustering.
The concept of clustering is adapted in view of the fact that, impact
of climate change can be studied in a homogeneous region without
much variation, which can be helpful in studies related to water
resources planning and management. 10 IMD (Indian Meteorological
Department) stations, situated in various regions of the North-east,
have been selected for making the clusters. The results of the Fuzzy
C-Means (FCM) analysis show different clustering patterns for
different conditions. From the analysis and comparison it can be
concluded that nonconventional method of using GCM data is
somehow giving better results than the others. However, further
analysis can be done by taking daily data instead of monthly means to
reduce the effect of standardization.
Abstract: In the present work, hydrogen gas sensor of modest
sensitivity utilizing functionalized multiwalled carbon nanotubes
partially decorated with tin oxide nanoparticles (F-MWCNTs/SnO2)
has been fabricated. This sensing material was characterized by
scanning electron microscopy (SEM). In addition, a remarkable
finding was that the F-MWCNTs/SnO2 sensor shows good sensitivity
as compared to F-MWCNTs for low concentration (0.05-1% by
volume) of H2 gas. The fabricated sensors show complete resistance
recovery and good repeatability when exposed to H2 gas at the room
temperature conditions.