Abstract: This paper presents numerical flow and slope stability simulations in three typical sections of earth dams built in tropical regions, two homogeneous with different slope inclinations, and the other one heterogeneous with impermeable core. The geotechnical material parameters used in this work were obtained from a lab testing of physical characterization, compaction, consolidation, variable load permeability and saturated triaxial type CD for compacted soil samples with standard proctor energy at optimum moisture content (23%), optimum moisture content + 2% and optimum moisture content +5%. The objective is to analyze the general behavior of earth dams built in rainy regions where optimum moisture is exceeded. The factor of safety is satisfactory for the three sections compacted in all moisture content during the stages of operation and end of construction. On The other hand, the rapid drawdown condition is the critical phase for homogeneus dams configuration, the factor of safety obtained were unsatisfactory. In general, the heterogeneous dam behavior is more efficient due to the fact that the slopes are made up of gravel, which favors the dissipation of pore pressures during the rapid drawdown. For the critical phase, the slopes should have lower inclinations of the upstream and downstream slopes to guarantee stability, although it increases the costs.
Abstract: In this paper, an attempt has been made to study the
effect of thermal gradation on the steady-state creep behavior of
rotating isotropic disc made of functionally graded material using
threshold stress based Sherby’s creep law. The composite discs made
of aluminum matrix reinforced with silicon carbide particulate have
been taken for analysis. The stress and strain rate distributions have
been calculated for the discs rotating at elevated temperatures having
thermal gradation. The material parameters of creep vary radially and
have been estimated by regression fit of the available experimental
data. Investigations for discs made up of linearly increasing particle
content operating under linearly decreasing temperature from inner
to outer radii have been done using von Mises’ yield criterion. The
results are displayed and compared graphically in designer friendly
format for the above said disc profile with the disc made of particle
reinforced composite operating under uniform temperature profile. It
is observed that radial and tangential stresses show minor variation
and the strain rates vary significantly in the presence of thermal
gradation as compared to disc having uniform temperature.
Abstract: The present paper investigates the effect of linear
thermal gradient on the steady-state creep behavior of rotating
isotropic disc using threshold stress based Sherby’s creep law.
The composite discs made of aluminum matrix reinforced with
silicon carbide particulate has been taken for analysis. The stress
and strain rate distributions have been calculated for discs rotating
at linear thermal gradation using von Mises’ yield criterion. The
material parameters have been estimated by regression fit of the
available experimental data. The results are displayed and compared
graphically in designer friendly format for the above said temperature
profile with the disc operating under uniform temperature profile. It is
observed that radial and tangential stresses show minor variation and
the strain rates vary significantly in the presence of thermal gradation
as compared to disc having uniform temperature.
Abstract: In this paper, we investigate theoretically the waves propagation in a lossless double-negative grounded slab (DNG). This study is performed by the Transverse Resonance Method (TRM). The proper or improper nature of real and complex modes is observed. They are highly dependent on metamaterial parameters, i.e. ɛr-negative, µr-negative, or both. Numerical results provided that only the proper complex modes (i.e., leaky modes) exist in DNG slab, and only the improper complex modes exist in single-negative grounded slab.
Abstract: The global solved problem is the calculation of the
parameters of ceramic material from a set of destruction tests of
ceramic heads of total hip joint endoprosthesis. The standard way of
calculation of the material parameters consists in carrying out a set of
3 or 4 point bending tests of specimens cut out from parts of the
ceramic material to be analysed. In case of ceramic heads, it is not
possible to cut out specimens of required dimensions because the
heads are too small (if the cut out specimens were smaller than the
normalised ones, the material parameters derived from them would
exhibit higher strength values than those which the given ceramic
material really has). A special destruction device for heads
destruction was designed and the solved local problem is the
modification of this destructive device based on the analysis of
tensile stress in the head for two different values of the depth of the
conical hole in the head. The goal of device modification is a shift of
the location with extreme value of σ1max from the region of head’s
hole bottom to its opening. This modification will increase the
credibility of the obtained material properties of bioceramics, which
will be determined from a set of head destructions using the Weibull
weakest link theory.
Abstract: In this paper, thick walled Cylindrical tanks or tubes
made of functionally graded material under internal pressure and
temperature gradient are studied. Material parameters have been
considered as power functions. They play important role in the
elastoplastic behavior of these materials. To clarify their role,
different materials with different parameters have been used under
temperature gradient. Finally, their effect and loading effect have
been determined in first yield point. Also, the important role of
temperature gradient was also shown. At the end the study has been
results obtained from changes in the elastic modulus and yield stress.
Also special attention is also given to the effects of this internal
pressure and temperature gradient in the creation of tensile and
compressive stresses.
Abstract: Well-designed composite steel and concrete structures
highlight the good material properties and lower the deficiencies of
steel and concrete, in particular they make use of high tensile strength
of steel and high stiffness of concrete. The most common composite
steel and concrete structure is a simply supported beam, which
concrete slab transferring the slab load to a beam is connected to the
steel cross-section. The aim of this paper is to find the most adequate
numerical model of a simply supported composite beam with the
cross-sectional and material parameters based on the results of a
processed parametric study and numerical analysis. The paper also
evaluates the suitability of using compact concrete with the
lightweight aggregates for composite steel and concrete beams. The
most adequate numerical model will be used in the resent future to
compare the results of laboratory tests.
Abstract: In this paper, we investigate the generalized Stokes’ problems for an incompressible couple stress fluid. Analytical solution of the governing equations is obtained in Laplace transform domain for each problem. A standard numerical inversion technique
is used to invert the Laplace transform of the velocity in each case. The effect of various material parameters on velocity is discussed and the results are presented through graphs. It is observed that, the results are in tune with the observation of V.K.Stokes in connection with the variation of velocity in the flow between two parallel plates when the top one is moving with constant velocity and the bottom one is at rest.
Abstract: Shear testing is one of the most complex testing areas where available methods and specimen geometries are different from each other. Therefore, a modified shear test specimen (MSTS) combining the simple uniaxial test with a zone of interest (ZOI) is tested which gives almost the pure shear. In this study, material parameters of polypropylene (PP) and high density polyethylene (HDPE) are first measured by tensile tests with a dogbone shaped specimen. These parameters are then used as an input for the finite element analysis. Secondly, a specially designed specimen (MSTS) is used to perform the shear stress tests in a tensile testing machine to get the results in terms of forces and extension, crack initiation etc. Scanning Electron Microscopy (SEM) is also performed on the shear fracture surface to find material behavior. These experiments are then simulated by finite element method and compared with the experimental results in order to confirm the simulation model. Shear stress state is inspected to find the usability of the proposed shear specimen. Finally, a geometry correction factor can be established for these two materials in this specific loading and geometry with notch using Linear Elastic Fracture Mechanics (LEFM). By these results, strain energy of shear failure and stress intensity factor (SIF) of shear of these two polymers are discussed in the special application of the screw cap opening of the medical or food packages with a temper evidence safety solution.
Abstract: In this paper back-propagation artificial neural network
(BPANN )with Levenberg–Marquardt algorithm is employed to
predict the deformation of the upsetting process. To prepare a
training set for BPANN, some finite element simulations were
carried out. The input data for the artificial neural network are a set
of parameters generated randomly (aspect ratio d/h, material
properties, temperature and coefficient of friction). The output data
are the coefficient of polynomial that fitted on barreling curves.
Neural network was trained using barreling curves generated by
finite element simulations of the upsetting and the corresponding
material parameters. This technique was tested for three different
specimens and can be successfully employed to predict the
deformation of the upsetting process
Abstract: In this paper, a study on the modes of collapse of
compress- expand members are presented. Compress- expand member
is a compact, multiple-combined cylinders, to be proposed as energy
absorbers. Previous studies on the compress- expand member have
clarified its energy absorption efficiency, proposed an approximate
equation to describe its deformation characteristics and also
highlighted the improvement that it has brought. However, for the
member to be practical, the actual range of geometrical dimension that
it can maintain its applicability must be investigated. In this study,
using a virtualized materials that comply the bilinear hardening law,
Finite element Method (FEM) analysis on the collapse modes of
compress- expand member have been conducted. Deformation maps
that plotted the member's collapse modes with regards to the member's
geometric and material parameters were then presented in order to
determine the dimensional range of each collapse modes.
Abstract: The paper deals with calculation of the parameters of
ceramic material from a set of destruction tests of ceramic heads of
total hip joint endoprosthesis. The standard way of calculation of the
material parameters consists in carrying out a set of 3 or 4 point
bending tests of specimens cut out from parts of the ceramic material
to be analysed. In case of ceramic heads, it is not possible to cut out
specimens of required dimensions because the heads are too small (if
the cut out specimens were smaller than the normalised ones, the
material parameters derived from them would exhibit higher strength
values than those which the given ceramic material really has). On
that score, a special testing jig was made, in which 40 heads were
destructed. From the measured values of circumferential strains of the
head-s external spherical surface under destruction, the state of stress
in the head under destruction was established using the final elements
method (FEM). From the values obtained, the sought for parameters
of the ceramic material were calculated using Weibull-s weakest-link
theory.
Abstract: Water vapour transport properties of gypsum block
are studied in dependence on relative humidity using inverse analysis
based on genetic algorithm. The computational inverse analysis is
performed for the relative humidity profiles measured along the
longitudinal axis of a rod sample. Within the performed transient
experiment, the studied sample is exposed to two environments with
different relative humidity, whereas the temperature is kept constant.
For the basic gypsum characterisation and for the assessment of input
material parameters necessary for computational application of
genetic algorithm, the basic material properties of gypsum are
measured as well as its thermal and water vapour storage parameters.
On the basis of application of genetic algorithm, the relative
humidity dependent water vapour diffusion coefficient and water
vapour diffusion resistance factor are calculated.
Abstract: In this paper back-propagation artificial neural network
(BPANN) is employed to predict the deformation of the upsetting
process. To prepare a training set for BPANN, some finite element
simulations were carried out. The input data for the artificial neural
network are a set of parameters generated randomly (aspect ratio d/h,
material properties, temperature and coefficient of friction). The
output data are the coefficient of polynomial that fitted on barreling
curves. Neural network was trained using barreling curves generated
by finite element simulations of the upsetting and the corresponding
material parameters. This technique was tested for three different
specimens and can be successfully employed to predict the
deformation of the upsetting process
Abstract: Coronary artery bypass grafts (CABG) are widely
studied with respect to hemodynamic conditions which play
important role in presence of a restenosis. However, papers which
concern with constitutive modeling of CABG are lacking in the
literature. The purpose of this study is to find a constitutive model for
CABG tissue. A sample of the CABG obtained within an autopsy
underwent an inflation–extension test. Displacements were
recoredered by CCD cameras and subsequently evaluated by digital
image correlation. Pressure – radius and axial force – elongation
data were used to fit material model. The tissue was modeled as onelayered
composite reinforced by two families of helical fibers. The
material is assumed to be locally orthotropic, nonlinear,
incompressible and hyperelastic. Material parameters are estimated
for two strain energy functions (SEF). The first is classical
exponential. The second SEF is logarithmic which allows
interpretation by means of limiting (finite) strain extensibility.
Presented material parameters are estimated by optimization based
on radial and axial equilibrium equation in a thick-walled tube. Both
material models fit experimental data successfully. The exponential
model fits significantly better relationship between axial force and
axial strain than logarithmic one.
Abstract: Primary barrier of membrane type LNG containment system consist of corrugated 304L stainless steel. This 304L stainless steel is austenitic stainless steel which shows different material behaviors owing to phase transformation during the plastic work. Even though corrugated primary barriers are subjected to significant amounts of pre-strain due to press working, quantitative mechanical behavior on the effect of pre-straining at cryogenic temperatures are not available. In this study, pre-strain level and pre-strain temperature dependent tensile tests are carried to investigate mechanical behaviors. Also, constitutive equations with material parameters are suggested for a verification study.
Abstract: The paper deals with the pulsating flow of an incompressible couple stress fluid between permeable beds. The couple stress fluid is injected into the channel from the lower permeable bed with a certain velocity and is sucked into the upper permeable bed with the same velocity. The flow between the permeable beds is assumed to be governed by couple stress fluid flow equations of V. K. Stokes and that in the permeable regions by Darcy-s law. The equations are solved analytically and the expressions for velocity and volume flux are obtained. The effects of the material parameters are studied numerically and the results are presented through graphs.
Abstract: Fuel and oxidant gas delivery plate, or fuel cell
plate, is a key component of a Proton Exchange Membrane (PEM)
fuel cell. To manufacture low-cost and high performance fuel cell
plates, advanced computer modeling and finite element structure
analysis are used as virtual prototyping tools for the optimization
of the plates at the early design stage. The present study examines
thermal stress analysis of the fuel cell plates that are produced
using a patented, low-cost fuel cell plate production technique
based on screen-printing. Design optimization is applied to
minimize the maximum stress within the plate, subject to strain
constraint with both geometry and material parameters as design
variables. The study reveals the characteristics of the printed
plates, and provides guidelines for the structure and material design
of the fuel cell plate.