Abstract: A local wastewater treatment plant (WWTP)
experiencing poor nitrification tracked down high level of
surfactants in the plant-s influent and effluent. The aims of this project were to assess the potential inhibitory effect of surfactants on activated sludge processes. The effect of the
presence of TergitolNP-9, TrigetolNP-7, Trigetol15-S-9,
dodecylbenzene sulphonate (SDBS) and sodium dodecyl
sulfate (SDS) on activated sludge oxygen uptake rate (OUR) and nitrification were assessed. The average concentration of non-ionic and anionic
surfactants in the influent to the local WWTP were 7 and 8.7 mg/L, respectively. Removal of 67% to 90% of the non-ionic and 93-99% of the anionic surfactants tested were measured. All surfactants tested showed inhibitory effects both on OUR
and nitrification. SDS incurred the lowest inhibition whereas
SDBS and NP-9 caused severe inhibition to OUR and
Nitrification. Activated sludge flocs sizes slightly decreased
after 3 hours contact with the surfactant present in the test.
The results obtained indicated that high concentrations of
surfactants are likely to have an adverse effect on the
performance of WWTPs utilizing activated sludge processes.
Abstract: In a pilot plant scale of a fluidized bed reactor, a
reduction reaction of sodium sulfate by natural gas has been
investigated. Natural gas is applied in this study as a reductant. Feed
density, feed mass flow rate, natural gas and air flow rate
(independent parameters)and temperature of bed and CO
concentration in inlet and outlet of reactor (dependent parameters)
were monitored and recorded at steady state. The residence time was
adjusted close to value of traditional reaction [1]. An artificial neural
network (ANN) was established to study dependency of yield and
carbon gradient on operating parameters. Resultant 97% accuracy of
applied ANN is a good prove that natural gas can be used as a
reducing agent. Predicted ANN model for relation between other
sources carbon gradient (accuracy 74%) indicates there is not a
meaningful relation between other sources carbon variation and
reduction process which means carbon in granule does not have
significant effect on the reaction yield.
Abstract: Despite of the preponderant role played by cement among the construction materials, it is today considered as a material destructing the environment due to the large quantities of carbon dioxide exhausted during its manufacture. Besides, global warming is now recognized worldwide as the new threat to the humankind against which advanced countries are investigating measures to reduce the current amount of exhausted gases to the half by 2050. Accordingly, efforts to reduce green gases are exerted in all industrial fields. Especially, the cement industry strives to reduce the consumption of cement through the development of alkali-activated geopolymer mortars using industrial byproducts like bottom ash. This study intends to gather basic data on the flowability and strength development characteristics of alkali-activated geopolymer mortar by examining its FT-IT features with respect to the effects and strength of the alkali-activator in order to develop bottom ash-based alkali-activated geopolymer mortar. The results show that the 35:65 mass ratio of sodium hydroxide to sodium silicate is appropriate and that a molarity of 9M for sodium hydroxide is advantageous. The ratio of the alkali-activators to bottom ash is seen to have poor effect on the strength. Moreover, the FT-IR analysis reveals that larger improvement of the strength shifts the peak from 1060 cm–1 (T-O, T=Si or Al) toward shorter wavenumber.
Abstract: A combination of photosynthetic bacteria along with
anaerobic acidogenic bacteria is an ideal option for efficient
hydrogen production. In the present study, the optimum
concentration of substrates for the growth of Rhodobacter
sphaeroides was found by response surface methodology. The
optimum combination of three individual fatty acids was determined
by Box Behnken design. Increase of volatile fatty acid concentration
decreased the growth. Combination of sodium acetate and sodium
propionate was most significant for the growth of the organism. The
results showed that a maximum biomass concentration of 0.916 g/l
was obtained when the concentrations of acetate, propionate and
butyrate were 0.73g/l,0.99g/l and 0.799g/l, respectively. The growth
was studied under an optimum concentration of volatile fatty acids
and at a light intensity of 3000 lux, initial pH of 7 and a temperature
of 35°C.The maximum biomass concentration of 0.92g/l was
obtained which verified the practicability of this optimization.
Abstract: The effects of coatings based on sodium alginate (S.A) and carboxyl methyl cellulose (CMC) on the color and moisture characteristics of potato round slices were investigated. It is the first time that this combination of polysaccharides is used as edible coating which alone had the best performance as inhibitor of potato color discoloration during the storage of 15 days at 4oC. When ascorbic acid (AA) and green tea (GT) were added in the above edible coating its effects on potato round slices changed. The mixtures of sodium alginate and carboxyl methyl cellulose with ascorbic acid or with green tea behave as a potential moisture barrier, resulting to the extent of potato samples self–life. These data suggests that both GT and AA are potential inhibitors of dehydration in potatoes and not only natural antioxidants.
Abstract: The effect of concentration of reduction agent of
sodium borohydrate (NaBH4) on the properties of silicon
nanoparticles synthesized via microemulsion route is reported. In
this work, the concentration of the silicon tetrachloride (SiCl4) that
served as silicon source with sodium hydroxide (NaOH) and
polyethylene glycol (PEG) as stabilizer and surfactant, respectively,
are keep fixed. Four samples with varied concentration of NaBH4
from 0.05 M to 0.20 M were synthesized. It was found that the lowest
concentration of NaBH4 gave better formation of silicon
nanoparticles.
Abstract: Tomato powder has good potential as substitute of tomato paste and other tomato products. In order to protect physicochemical properties and nutritional quality of tomato during dehydration process, investigation was carried out using different drying methods and pretreatments. Solar drier and continuous conveyor (tunnel) drier were used for dehydration where as calcium chloride (CaCl2), potassium metabisulphite (KMS), calcium chloride and potassium metabisulphite (CaCl2 +KMS), and sodium chloride (NaCl) selected for treatment.. lycopene content, dehydration ratio, rehydration ratio and non-enzymatic browning in addition to moisture, sugar and titrable acidity were studied. Results show that pre-treatment with CaCl2 and NaCl increased water removal and moisture mobility in tomato slices during drying of tomatoes. Where CaCl2 used along with KMS the NEB was recorded the least compared to other treatments and the best results were obtained while using the two chemicals in combination form. Storage studies in LDPE polymeric and metalized polyesters films showed less changes in the products packed in metallized polyester pouches and even after 6 months lycopene content did not decrease more than 20% as compared to the control sample and provide extension of shelf life in acceptable condition for 6 months. In most of the quality characteristics tunnel drier samples presented better values in comparison to solar drier.
Abstract: The manufacturing transmission line tower parts has
being generated hazardous waste which is required proper disposal
of waste for protection of land pollution. Manufacturing Process in
the manufacturing of steel angle, plates, pipes, channels are passes
through conventional, semi automatic and CNC machines for
cutting, marking, punching, drilling, notching, bending operations.
All fabricated material Coated with thin layer of Zinc in Galvanizing
plant where molten zinc is used for coating. Prior to Galvanizing,
chemical like 33% concentrated HCl Acid, ammonium chloride and
d-oil being used for pretreatment of iron. The bath of water with
sodium dichromate is used for cooling and protection of the
galvanized steel. For the heating purpose the furnace oil burners are
used. These above process the Zinc dross, Zinc ash, ETP sludge and
waste pickled acid generated as hazardous waste. The RPG has
made captive secured land fill site, since 1997 since then it was
using for disposal of hazardous waste after completion of SLF
(Secured land fill) site. The RPG has raised height from ground
level then now it is being used for disposal of waste as he designed
the SLF after in creasing height of from GL it is functional without
leach ate or adverse impacts in the environment.
Abstract: Twenty four New Zealand white rabbits (12 does and
12 bucks) and twenty four Flanders (12 does and 12 bucks) rabbits,
allotted into two feeding regime (6 for each breed, 3 males and 3
females) first one fed commercial ration and second one fed
commercial diet plus sodium butyrate (300 g/ton). The obtained
results showed that at end of 8th week experimental period New
Zealand white rabbits were heavier body weight than Flanders rabbits
(1934.55+39.05 vs. 1802.5+30.99 g); significantly high body weight
gain during experimental period especially during 8th week
(136.1+3.5 vs. 126.8+1.8 g/week); better feed conversion ratio during
all weeks of experiment from first week (3.07+0.16 vs. 3.12+0.10)
till the 8th week of experiment (5.54+0.16 vs. 5.76+0.07) with
significantly high dressing percentages (0.54+0.01 vs. 0.52+0.01).
Also all carcass cuts were significantly high in New Zealand white
rabbits than Flanders. Females rabbits (at the same age) were lower
body weight than males from start of experiment (941.1+39.8
vs.972.1+33.5 g) till the end of experiment (1833.64+37.69 vs.
1903.41+36.93 g); gained less during all weeks of experiment except
during 8th week (132.1+2.3 vs. 130.9+3.4 g/week), with lower
dressing percentage (0.52+0.01 vs. 0.53+0.01) and lighter carcass
cuts than males, however, they had better feed conversion ratio
during 1st week, 7th week and 8th week of experiment. Addition of
300g sodium butyrate/ton of rabbit increased the body weight of
rabbits at the end of experimental period (1882.71+26.45 vs.
1851.5+49.82 g); improve body weight gain at 3rd, 4th, 5th, 6th and
7th week of experiment and significantly improve feed conversion
ratio during all weeks of the experiment from 1st week (2.85+0.07
vs. 3.30+0.15) till the 8th week of the experiment (5.51+0.12 vs.
5.77+0.12). Also the dressing percentage was higher in Sodium
butyrate fed groups than control one (0.53+0.01 vs. 0.52+0.01) and
the most important results of feeding sodium butyrate is the reducing
of the mortality percentage in rabbits during 8 week experiment to
zero percentage as compared with 16% in control group.
Abstract: Aggregation behavior of sodium salicylate and sodium cumene sulfonate was studied in aqueous solution at different temperature. Specific conductivity and relative viscosity were measured at different temperature to find minimum hydrotropic concentration. The thermodynamic parameters (free energy, enthalpy and entropy) were evaluated in the temperature range of 30°C-70°C. The free energy decreased with increase in temperature. The aggregation was found to be exothermic in nature and favored by positive value of entropy.
Abstract: This was the first document revealing the
investigation of protein hydrolysate production optimization from J.
curcas cake. Proximate analysis of raw material showed 18.98%
protein, 5.31% ash, 8.52% moisture and 12.18% lipid. The
appropriate protein hydrolysate production process began with
grinding the J. curcas cake into small pieces. Then it was suspended
in 2.5% sodium hydroxide solution with ratio between solution/ J.
curcas cake at 80:1 (v/w). The hydrolysis reaction was controlled at
temperature 50 °C in water bath for 45 minutes. After that, the
supernatant (protein hydrolysate) was separated using centrifuge at
8000g for 30 minutes. The maximum yield of resulting protein
hydrolysate was 73.27 % with 7.34% moisture, 71.69% total protein,
7.12% lipid, 2.49% ash. The product was also capable of well
dissolving in water.
Abstract: This paper reports the results of an experimental work
conducted to investigate the effect of curing conditions on the
compressive strength of self-compacting geopolymer concrete
prepared by using fly ash as base material and combination of sodium
hydroxide and sodium silicate as alkaline activator. The experiments
were conducted by varying the curing time and curing temperature in
the range of 24-96 hours and 60-90°C respectively. The essential
workability properties of freshly prepared Self-compacting
Geopolymer concrete such as filling ability, passing ability and
segregation resistance were evaluated by using Slump flow,
V-funnel, L-box and J-ring test methods. The fundamental
requirements of high flowability and resistance to segregation as
specified by guidelines on Self-compacting Concrete by EFNARC
were satisfied. Test results indicate that longer curing time and curing
the concrete specimens at higher temperatures result in higher
compressive strength. There was increase in compressive strength
with the increase in curing time; however increase in compressive
strength after 48 hours was not significant. Concrete specimens cured
at 70°C produced the highest compressive strength as compared to
specimens cured at 60°C, 80°C and 90°C.
Abstract: This study was conducted to evaluate factors
regulating groundwater quality in an area with agriculture as main
use. Under this study twelve groundwater samples have been
collected from Padra taluka, Dabhoi taluka and Savli taluka of
Vadodara district. Groundwater samples were chemically analyzed
for major physicochemical parameter in order to understand the
different geochemical processes affecting the groundwater quality.
The analytical results shows higher concentration of total dissolved
solids (16.67%), electrical conductivity (25%) and magnesium
(8.33%) for pre monsoon and total dissolved solids (16.67%),
electrical conductivity (33.3%) and magnesium (8.33%) for post
monsoon which indicates signs of deterioration as per WHO and BIS
standards. On the other hand, 50% groundwater sample is unsuitable
for irrigation purposes based on irrigation quality parameters. The
study revealed that application of fertilizer for agricultural
contributing the higher concentration of ions in aquifer of Vadodara
district.
Abstract: There is growing interest in biodiesel (fatty acid
methyl ester or FAME) because of the similarity in its properties
when compared to those of diesel fuels. Diesel engines operated on
biodiesel have lower emissions of carbon monoxide, unburned
hydrocarbons, particulate matter, and air toxics than when operated
on petroleum-based diesel fuel. Production of fatty acid methyl ester
(FAME) from rapeseed (nonedible oil) fatty acid distillate having
high free fatty acids (FFA) was investigated in this work. Conditions
for esterification process of rapeseed oil were 1.8 % H2SO4 as
catalyst, MeOH/oil of molar ratio 2 : 0.1 and reaction temperature
65 °C, for a period of 3h. The yield of methyl ester was > 90 % in 1
h.
The amount of FFA was reduced from 93 wt % to less than 2 wt %
at the end of the esterification process. The FAME was pureed by
neutralization with 1 M sodium hydroxide in water solution at a
reaction temperature of 62 °C. The final FAME product met with the
biodiesel quality standard, and ASTM D 6751.
Abstract: Impaired fertility may be the result of indirect
consumption of anti-fertility agents through food. Monosodium
glutamate (MSG) has been widely used as food additive, flavour
enhancer and included in vaccines. This study focuses in determining
the gonadotoxic and cytotoxic effect of MSG on selected sperm
parameters such as sperm viability, sperm membrane integrity and
testes cytoarchitecture of male mice via histological examination to
determine its effect on spermatogenesis. Twenty-four Mus musculus
were randomly divided into 4 groups and given intraperitoneal
injections (IP) daily for 14 days of different MSG concentrations at
250, 500 and 1000mg/kg MSG to body weight to induce obesity.
Saline was given to control group. Mice were sacrificed and analysis
revealed abnormalities in values for sperm parameters and damages
to testes cytoarchitecture of male mice. The results recorded
decreased viability (p0.05) with degenerative structures in seminiferous tubule of
testes. The results indicated various implications of MSG on male
mice reproductive system which has consequences in fertility
potential.
Abstract: Biodisel is a type of biofuel having similar properties of diesel fuel but lacks substances (undesirable emissions) such as sulfur, nitrogen and aromatic polycyclic. Upon filtration of waste oil, the biodiesel fuel was produced via carrying out transestrification reaction of triglycerides followed by conducting viscosity, density, flash point, cloud point, pour point and copper strip corrosion tests on the samples and comparing with EN14214 and ASTM 6751 standards and all results were found in the permitted limit. The highest yield of biodiesel production reaction was found 46.6435 g when Sodium Hydroxide catalyst in amount of 0.375g was employed, 44.2347 g when Sodium methoxide catalyst in amount of 0.5g was employed and 56.5124 g when acid sulfuric catalyst in amount of 1g was employed and 47.3290 g when two stage reaction was done.
Abstract: As the Textile Industry is the second largest industry
in Egypt and as small and medium-sized enterprises (SMEs) make up
a great portion of this industry therein it is essential to apply the
concept of Cleaner Production for the purpose of reducing pollution.
In order to achieve this goal, a case study concerned with ecofriendly
stone-washing of jeans-garments was investigated. A raw
material-substitution option was adopted whereby the toxic
potassium permanganate and sodium sulfide were replaced by the
environmentally compatible hydrogen peroxide and glucose
respectively where the concentrations of both replaced chemicals
together with the operating time were optimized. In addition, a
process-rationalization option involving four additional processes
was investigated. By means of criteria such as product quality,
effluent analysis, mass and heat balance; and cost analysis with the
aid of a statistical model, a process optimization treatment revealed
that the superior process optima were 50%, 0.15% and 50min for
H2O2 concentration, glucose concentration and time, respectively.
With these values the superior process ought to reduce the annual
cost by about EGP 105 relative to the currently used conventional
method.
Abstract: Transcription factor p53 has a powerful tumor
suppressing function that is associated with many cancers. However,
p53 of the molecular weight was higher make the limitation across to
skin or cell membrane. Thymidine dinucleotide (pTT), an
oligonucleotide, can activate the p53 transcription factor. pTT is a
hydrophilic and negative charge oligonucleotide, which delivery in to
cell membrane need an appropriate carrier. The aim of this study was
to improve the bioavailability of the nucleotide fragment, thymidine
dinucleotide (pTT), using elasic liposome carriers to deliver the drug
into the skin. The study demonstrate that dioleoylphosphocholine
(DOPC) incorporated with sodium cholate at molar ratio 1:1 can
archived the particle size about 220 nm. This elastic liposome could
penetration through skin from stratum corneum to whole epidermis by
confocal laser scanning microscopy (CLSM). Moreover, we observed
the the slight increase in generation of p53 by western blot.
Abstract: This paper presents the findings of an
experimental investigation to study the effect of alkali content
in geopolymer mortar specimens exposed to sulphuric acid.
Geopolymer mortar specimens were manufactured from Class F fly
ash by activation with a mixture of sodium hydroxide and sodium
silicate solution containing 5% to 8% Na2O. Durability of specimens
were assessed by immersing them in 10% sulphuric acid solution and
periodically monitoring surface deterioration and depth of
dealkalization, changes in weight and residual compressive strength
over a period of 24 weeks. Microstructural changes in the specimens
were studied with Scanning electron microscopy (SEM) and EDAX.
Alkali content in the activator solution significantly affects the
durability of fly ash based geopolymer mortars in sulphuric acid.
Specimens manufactured with higher alkali content performed better
than those manufactured with lower alkali content. After 24 weeks in
sulphuric acid, specimen with 8% alkali still recorded a residual
strength as high as 55%.
Abstract: The aim of the study was to evaluate the effect of
texturizers on the rheological properties of the apple mass and
desserts made from various raw materials. The apple varieties -
‘Antonovka’, ‘Baltais Dzidrais’, and ‘Zarja Alatau’ harvested in
Latvia, were used for the experiment. The apples were processed in a
blender unpeeled for obtaining a homogenous mass. The apple mass
was analyzed fresh and after storage at –18ºC. Both fresh and thawed
apple mass samples with added gelatin, xantan gum, and sodium
carboxymethylcellulose were whisked obtaining dessert. Pectin, pH
and soluble dry matter of the product were determined. Apparent
viscosity was measured using a rotational viscometer DV–III Ultra.
Pectin content in frozen apple mass decreased significantly (p