Abstract: The study assessed the effectiveness of Pawpaw
(Carica papaya) wood in reducing the concentrations of heavy
metals in wastewater acting as a bio-sorbent. The following heavy
metals were considered; Zinc, Cadmium, Lead, Copper, Iron,
Selenium, Nickel and Manganese. The physiochemical properties of
Carica papaya stem were studied. The experimental sample was
sourced from the trunk of a felled matured pawpaw tree. Wastewater
for experimental use was prepared by dissolving soil samples
collected from a dump site at Owerri, Imo state of Nigeria in water.
The concentration of each metal remaining in solution as residual
metal after bio-sorption was determined using Atomic absorption
Spectrometer. The effects of pH and initial heavy metal concentration
were studied in a batch reactor. The results of Spectrometer test
showed that there were different functional groups detected in the
Carica papaya stem biomass. There was increase in metal removal as
the pH increased for all the metals considered except for Nickel and
Manganese. Optimum bio-sorption occurred at pH 5.9 with 5g/100ml
solution of bio-sorbent. The results of the study showed that the
treated wastewater is fit for irrigation purpose based on Canada
wastewater quality guideline for the protection of Agricultural
standard. This approach thus provides a cost effective and
environmentally friendly option for treating wastewater.
Abstract: The main purpose of this study is to assess the
sediment quality and potential ecological risk in marine sediments in
Gymea Bay located in south Sydney, Australia. A total of 32 surface
sediment samples were collected from the bay. Current track
trajectories and velocities have also been measured in the bay. The
resultant trace elements were compared with the adverse biological
effect values Effect Range Low (ERL) and Effect Range Median
(ERM) classifications. The results indicate that the average values of
chromium, arsenic, copper, zinc, and lead in surface sediments all
reveal low pollution levels and are below ERL and ERM values. The
highest concentrations of trace elements were found close to
discharge points and in the inner bay, and were linked with high
percentages of clay minerals, pyrite and organic matter, which can
play a significant role in trapping and accumulating these elements.
The lowest concentrations of trace elements were found to be on the
shoreline of the bay, which contained high percentages of sand
fractions. It is postulated that the fine particles and trace elements are
disturbed by currents and tides, then transported and deposited in
deeper areas. The current track velocities recorded in Gymea Bay had
the capability to transport fine particles and trace element pollution
within the bay. As a result, hydrodynamic measurements were able to
provide useful information and to help explain the distribution of
sedimentary particles and geochemical properties. This may lead to
knowledge transfer to other bay systems, including those in remote
areas. These activities can be conducted at a low cost, and are
therefore also transferrable to developing countries. The advent of
portable instruments to measure trace elements in the field has also
contributed to the development of these lower cost and easily applied
methodologies available for use in remote locations and low-cost
economies.
Abstract: Diets high in processed foods have been found to lack
essential micro-nutrients for optimum human development and
overall health. Some micro-nutrients such as copper (Cu) have been
found to enhance the inflammatory response through its oxidative
functions, thereby having a role in cardiovascular disease, metabolic
syndrome, diabetes and related complications. This research study
was designed to determine if food crops could be bio-fortified with
micro-nutrients by growing sprouts on mineral fortified fiber mats. In
the feasibility study described in this contribution, recycled cellulose
fibers and clay, saturated with either micro-nutrient copper ions or
copper nanoparticles, were converted to a novel mineral-cellulose
fiber carrier of essential micro-nutrient and of antimicrobial
properties. Seeds of Medicago sativa (alfalfa), purchased from a
commercial, organic supplier were germinated on engineered
cellulose fiber mats. After the appearance of the first leaves, the
sprouts were dehydrated and analyzed for Cu content. Nutrient
analysis showed ~2 increase in Cu of the sprouts grown on the fiber
mats with copper particles, and ~4 increase on mats with ionic copper
as compared to the control samples. This study illustrates the
potential for the use of engineered mats as a viable way to increase
the micro-nutrient composition of locally-grown food crops and the
need for additional research to determine the uptake, nutritional
implications and risks of micro-nutrient bio-fortification.
Abstract: Pure nickel coatings have been successfully
electrodeposited on copper substrates by the pulse plating technique.
The influence of current density, duty cycle and pulse frequency on
the surface morphology, crystal orientation, and microhardness was
determined. It was found that the crystallite size of the deposit
increases with increasing current density and duty cycle. The crystal
orientation progressively changed from a random texture at 1 A/dm2
to (200) texture at 10 A/dm2. Increasing pulse frequency resulted in
increased texture coefficient and peak intensity of (111) reflection.
An increase in duty cycle resulted in considerable increase in texture
coefficient and peak intensity of (311) reflection. Coatings obtained
at high current densities and duty cycle present a mixed morphology
of small and large grains. Maximum microhardness of 193 Hv was
achieved at 4 A/dm2, 10 Hz and duty cycle of 50%. Nickel coatings
with (200) texture are ductile while (111) texture improves the
microhardness of the coatings.
Abstract: CuO thin films were deposited by spray ultrasonic
pyrolysis with different precursor solution. Two staring solution slats
were used namely: copper acetate and copper chloride. The influence
of these solutions on CuO thin films proprieties of is instigated. The
X rays diffraction (XDR) analysis indicated that the films deposed
with copper acetate are amorphous however the films elaborated with
copper chloride have monoclinic structure. UV- Visible transmission
spectra showed a strong absorbance of the deposited CuO thin films
in the visible region. Electrical characterization has shown that CuO
thin films prepared with copper acetate have a higher electrical
conductivity.
Abstract: This study focuses on the hydro-geology and chemical
constituents analysis of Ikogosi Warm Spring waters in South West
Nigeria. Ikogosi warm spring is a global tourist attraction because it
has both warm and cold spring sources. Water samples from the cold
spring, warm spring and the meeting point were collected, analyzed
and the result shows close similarity in temperature, hydrogen iron
concentration (pH), alkalinity, hardness, Calcium, Magnesium,
Sodium, Iron, total dissolved solid and heavy metals. The measured
parameters in the water samples are within World Health
Organisation standards for fresh water. The study of the geology of
the warm spring reveals that the study area is underlain by a group of
slightly migmatised to non-migmatised paraschists and meta-igneous
rocks. Also, concentration levels of selected heavy metals, (Copper,
Cadmium, Zinc, Arsenic and Cromium) were determined in the water
(ppm) samples. Chromium had the highest concentration value of
1.52ppm (an average of 49.67%) and Cadmium had the lowest
concentration with value of 0.15ppm (an average of 4.89%).
Comparison of these results showed that, their mean levels are within
the standard values obtained in Nigeria. It can be concluded that both
warm and spring water are safe for drinking.
Abstract: The ferrites ZnFe2O4, CdFe2O4 and CuFe2O4 are
synthesized in laboratory conditions using ceramic technology. Their
homogeneity and structure are proven by X-Ray diffraction analysis
and Mössbauer spectroscopy. The synthesized ferrites are subjected
to strong acid and high temperature leaching with solutions of H2SO4,
HCl and HNO3. The results indicate that the highest degree of
leaching of Zn, Cd and Cu from the ferrites is achieved by use of
HCl. The charging of five zinc sulfide concentrates was optimized using
the criterion of minimal amount of zinc ferrite produced when
roasting the concentrates in a fluidized bed. The results obtained are
interpreted in terms of the hydrometallurgical zinc production and
maximum recovery of zinc, copper and cadmium from initial zinc
concentrates after their roasting.
Abstract: This paper presents the result of an experimental
investigation regarding the use of Fe2O3 nanoparticles added to
kerosene as a working fluid, under magnetic field for Copper
Oscillating Heat pipe with inclination angle of 0°(horizontal), 15°,
30°,45°, 60°,75° and 90° (vertical). The following were examined;
measure the temperature distribution and heat transfer rate on
Oscillating Heat Pipe (OHP), with magnetic field under different
angles. Results showed that the addition of Fe2O3 nanoparticles under
magnetic field improved thermal performance of OHP especially in
75°.
Abstract: A multilayer passive shield composed of low-activity
lead (Pb), copper (Cu), tin (Sn) and iron (Fe) was designed and
manufactured for a coaxial HPGe detector placed at a surface
laboratory for reducing background radiation and radiation dose to
the personnel. The performance of the shield was evaluated and
efficiency curves of the detector were plotted by using of various
standard sources in different distances. Monte Carlo simulations and
a set of TLD chips were used for dose estimation in two distances of
20 and 40 cm. The results show that the shield reduced background
spectrum and the personnel dose more than 95%.
Abstract: This paper presents the influences on the entrainment
of serpentines by grinding and reagents during copper–nickel sulfide
flotation. The previous bench flotation tests were performed to extract
the metallic values from the ore in Yunnan Mine, China and the
relatively satisfied results with recoveries of 86.92% Cu, 54.92% Ni,
and 74.73% Pt+Pd in the concentrate were harvested at their grades of
4.02%, 3.24% and 76.61 g/t, respectively. However, the content of
MgO in the concentrate was still more than 19%. Micro-flotation tests
were conducted with the objective of figuring out the influences on the
entrainment of serpentines into the concentrate by particle size,
flocculants or depressants and collectors, as well as visual
observations in suspension by OLYMPUS camera. All the tests results
pointed to the presences of both “entrapped-in” serpentines and its
coating on the hydrophobic flocs resulted from strong collectors
(combination of butyl xanthate, butyl ammonium dithophosphate,
even after adding carboxymethyl cellulose as effective depressant.
And fine grinding may escalate the entrainment of serpentines in the
concentrate.
Abstract: Chalcopyrite (CuFeS2) is the most common primary
mineral used for the commercial production of copper. The low
dissolution efficiency of chalcopyrite in sulfate media has prevented
an efficient industrial leaching of this mineral in sulfate media. Ferric
ions, bacteria, oxygen and other oxidants have been used as oxidizing
agents in the leaching of chalcopyrite in sulfate and chloride media
under atmospheric or pressure leaching conditions. Two leaching
methods were studied to evaluate chalcopyrite (CuFeS2) dissolution
in acid media. First, the conventional oxidative acid leaching method
was carried out using sulfuric acid (H2SO4) and potassium
dichromate (K2Cr2O7) as oxidant at atmospheric pressure. Second,
microwave-assisted acid leaching was performed using the
microwave accelerated reaction system (MARS) for same reaction
media. Parameters affecting the copper extraction such as leaching
time, leaching temperature, concentration of H2SO4 and
concentration of K2Cr2O7 were investigated. The results of
conventional acid leaching experiments were compared to the
microwave leaching method. It was found that the copper extraction
obtained under high temperature and high concentrations of oxidant
with microwave leaching is higher than those obtained
conventionally. 81% copper extraction was obtained by the
conventional oxidative acid leaching method in 180 min, with the
concentration of 0.3 mol/L K2Cr2O7 in 0.5M H2SO4 at 50 ºC, while
93.5% copper extraction was obtained in 60 min with microwave
leaching method under same conditions.
Abstract: The synthesis of CuFe2O4 spinel powders by an
optimized combustion-like process followed by calcination is
described herein. The samples were characterized using X-ray
diffraction (XRD), differential thermal analysis (TG/DTA), scanning
electron microscopy (SEM), dilatometry and 4-probe DC methods.
Different glycine to nitrate (G/N) ratios of 1 (fuel-deficient), 1.48
(stoichiometric) and 2 (fuel-rich) were employed. Calcining the asprepared
powders at 800 and 1000°C for 5 hours showed that the G/N
ratio of 2 results in the formation of the desired copper spinel single
phase at both calcination temperatures. For G/N=1, formation of
CuFe2O4 takes place in three steps. First, iron and copper nitrates
decompose to iron oxide and pure copper. Then, copper transforms to
copper oxide and finally, copper and iron oxides react with each other
to form a copper ferrite spinel phase. The electrical conductivity and
the coefficient of thermal expansion of the sintered pelletized
samples were 2 S.cm-1 (800°C) and 11×10-6 °C-1 (25-800°C),
respectively.
Abstract: Nanotechnology has become the world attention in
various applications including the solar cells devices due to the
uniqueness and benefits of achieving low cost and better
performances of devices. Recently, thin film solar cells such as
Cadmium Telluride (CdTe), Copper-Indium-Gallium-diSelenide
(CIGS), Copper-Zinc-Tin-Sulphide (CZTS), and Dye-Sensitized
Solar Cells (DSSC) enhanced by nanotechnology have attracted
much attention. Thus, a compilation of nanotechnology devices
giving the progress in the solar cells has been presented. It is much
related to nanoparticles or nanocrystallines, carbon nanotubes, and
nanowires or nanorods structures.
Abstract: In recent research copper and manganese systems
were found to be the most active in CO and organic compounds
oxidation among the base catalysts. The mixed copper manganese
oxide has been widely studied in oxidation reactions because of their
higher activity at low temperatures in comparison with single oxide
catalysts. The results showed that the formation of spinel
CuxMn3−xO4 in the oxidized catalyst is responsible for the activity
even at room temperature. That is why the most of the investigations
are focused on the hopcalite catalyst (CuMn2O4) as the best coppermanganese
catalyst. Now it’s known that this is true only for CO
oxidation, but not for mixture of CO and VOCs. The purpose of this
study is to investigate the alumina supported copper-manganese
catalysts with different Cu/Mn molar ratio in terms of oxidation of
CO, methanol and dimethyl ether. The catalysts were prepared by impregnation of γ-Al2O3 with
copper and manganese nitrates and the catalytic activity
measurements were carried out in two stage continuous flow
equipment with an adiabatic reactor for simultaneous oxidation of all
compounds under the conditions closest possible to the industrial. Gas
mixtures on the input and output of the reactor were analyzed with a
gas chromatograph, equipped with FID and TCD detectors. The
texture characteristics were determined by low-temperature (- 196oС)
nitrogen adsorption in a Quantachrome Instruments NOVA 1200e
(USA) specific surface area & pore analyzer. Thermal, XRD and
TPR analyses were performed. It was established that the active component of the mixed Cu-
Mn/γ–alumina catalysts strongly depends on the Cu/Mn molar ratio.
Highly active alumina supported Cu-Mn catalysts for CO, methanol
and DME oxidation were synthesized. While the hopcalite is the best
catalyst for CO oxidation, the best compromise for simultaneous
oxidation of all components is the catalyst with Cu/Mn molar ratio
1:5.
Abstract: This work studies the effect of chemical composition
on the activity and selectivity of γ–alumina supported CuO/
MnO2/Cr2O3 catalysts toward deep oxidation of CO, dimethyl ether
(DME) and methanol. The catalysts were prepared by impregnation
of the support with an aqueous solution of copper nitrate, manganese
nitrate and CrO3 under different conditions. Thermal, XRD and TPR
analysis were performed. The catalytic measurements of single
compounds oxidation were carried out on continuous flow equipment
with a four-channel isothermal stainless steel reactor. Flow-line
equipment with an adiabatic reactor for simultaneous oxidation of all
compounds under the conditions that mimic closely the industrial
ones was used. The reactant and product gases were analyzed by
means of on-line gas chromatographs.
On the basis of XRD analysis it can be concluded that the active
component of the mixed Cu-Mn-Cr/γ–alumina catalysts consists of at
least six compounds – CuO, Cr2O3, MnO2, Cu1.5Mn1.5O4,
Cu1.5Cr1.5O4 and CuCr2O4, depending on the Cu/Mn/Cr molar ratio.
Chemical composition strongly influences catalytic properties, this
influence being quite variable with regards to the different processes.
The rate of CO oxidation rapidly decrease with increasing of
chromium content in the active component while for the DME was
observed the reverse trend. It was concluded that the best
compromise are the catalysts with Cu/(Mn + Cr) molar ratio 1:5 and
Mn/Cr molar ratio from 1:3 to 1:4.
Abstract: Mustard leaves are rich in folates, vitamin A, K and
B-complex. Mustard greens are low in calories and fats and rich in
dietary fiber. They are rich in potassium, manganese, iron, copper,
calcium, magnesium and low in sodium. It is very rich in antioxidants
and Phytonutrients. For the optimization of process variables
(moisture content and mustard leave powder), the experiments were
conducted according to central composite Face Centered Composite
design of RSM. The mustard leaves powder was replaced with
composite flour (a combination of rice, chickpea and corn in the ratio
of 70:15:15). The extrudate was extruded in a twin screw extruder at
a barrel temperature of 120°C. The independent variables were
mustard leaves powder (2-10 %) and moisture content (12-20 %).
Responses analyzed were bulk density, water solubility index, water
absorption index, lateral expansion, antioxidant activity, total
phenolic content, and overall acceptability. The optimum conditions
obtained were 7.19 g mustard leaves powder in 100g premix having
16.8% moisture content (w.b).
Abstract: Diagnostic enzymes like aspartate aminotransferase
(AST), alanine aminotransferase (ALT) and alkaline phosphatase
(ALP) were determined as indices of heavy metal pollution in Tilapia
guinensis. Three different sets of fishes treated with lead (Pb), iron
(Fe) and copper (Cu) were used for the study while a fourth group
with no heavy metal served as a control. Fishes in each of the groups
were exposed to 2.65mg/l of Pb, 0.85mg/l of Fe and 0.35 mg/l of Cu
in aerated aquaria for 96 hours. Tissue fractionation of the liver
tissues was carried out and the three diagnostic enzymes (AST, ALT,
and ALP) were estimated. Serum levels of the same diagnostic
enzymes were also measured. The mean values of the serum enzyme
activity for ALP in each experimental group were 19.5±1.62,
29.67±2.17 and 1.15±0.27 IU/L for Pb, Fe and Cu groups compared
with 9.99±1.34 IU/L enzyme activity in the control. This result
showed that Pb and Fe caused increased release of the enzyme into
the blood circulation indicating increased tissue damage while Cu
caused a reduction in the serum level as compared with the level in
the control group. The mean values of enzyme activity obtained in
the liver were 102.14±6.12, 140.17±2.06 and 168.23±3.52 IU/L for
Pb, Fe and Cu groups, respectively compared to 91.20±9.42 IU/L
enzyme activity for the control group. The serum and liver AST and
ALT activities obtained in Pb, Fe, Cu and control groups are
reported. It was generally noted that the presence of the heavy metal
caused liver tissues damage and consequent increased level of the
diagnostic enzymes in the serum.
Abstract: Toxicity of copper (Cu), lead (Pb) and iron (Fe) to
Tilapia guinensis was carried out for 4 days with a view to
determining their effects on the liver and muscle tissues. Tilapia
guinensis samples of about 10 - 14cm length and 0.2 – 0.4kg weight
each were obtained from University of Calabar fish ponds and
acclimated for three (3) days before the experimental set up.
Survivors after the 96-hr LC50 test period were selected from test
solutions of the heavy metals for the histopathological studies.
Histological preparations of liver and muscle tissues were randomly
examined for histopathological lesions. Results of the histological
examinations showed gross abnormalities in the liver tissues due to
pathological and degenerative changes compared to liver and muscle
tissues from control samples (tilapia fishes from aquaria without
heavy metals). Extensive hepatocyte necrosis with chronic
inflammatory changes was observed in the liver of fishes exposed to
Cu solution. Similar but less damaging effects were observed in the
liver of fishes exposed to Pb and Fe. The extent of lesion observed
was therefore heavy metal-related. However, no pathologic changes
occurred in the muscle tissues.
Abstract: Experts, enterprises and operators expect that the
bandwidth request will increase up to rates of 100 to 1,000 Mbps
within several years. Therefore the most important question is which
technology shall satisfy the future consumer broadband demands.
Currently the consensus is, that the fiber technology has the best
technical characteristics to achieve such the high bandwidth rates.
But fiber technology is so far very cost-intensive and resource
consuming. To avoid these investments, operators are concentrating
to upgrade the existing copper and hybrid fiber coax infrastructures.
This work presents a comparison of the copper and fiber
technologies including an overview about the current German
broadband market. Both technologies are reviewed in the terms of
demand, willingness to pay and economic efficiency in connection
with the technical characteristics.
Abstract: In this study, the experiments were carried out to
determine the best coolant for the quenching process among waterbased
silica, alumina, titania and copper oxide nanofluids (0.1 vol%).
A sphere made up off brass material was used in the experiments.
When the spherical test specimen was heated at high temperatures, it
was suddenly immersed into the nanofluids. All experiments were
carried out at saturated conditions and under atmospheric pressure.
After the experiments, the cooling curves were obtained by using the
temperature-time data of the specimen. The experimental results
showed that the cooling performance of test specimen depended on
the type of nanofluids. The silica nanoparticles enhanced the
performance of boiling heat transfer and it is the best coolant for the
quenching among other nanoparticles.