Abstract: Saturated two-phase fluid flows are often subject to
pressure induced oscillations. Due to compressibility the vapor
bubbles act as a spring with an asymmetric non-linear characteristic.
The volume of the vapor bubbles increases or decreases differently if
the pressure fluctuations are compressing or expanding;
consequently, compressing pressure fluctuations in a two-phase pipe
flow cause less displacement in the direction of the pipe flow than
expanding pressure fluctuations. The displacement depends on the
ratio of liquid to vapor, the ratio of pressure fluctuations over average
pressure and on the exciting frequency of the pressure fluctuations.
In addition, pressure fluctuations in saturated vapor bubbles cause
condensation and evaporation within the bubbles and change
periodically the ratio between liquid to vapor, and influence the
dynamical parameters for the oscillation. The oscillations are
conforming to an isenthalpic process at constant enthalpy with no
heat transfer and no exchange of work.
The paper describes the governing non-linear equation for twophase
fluid oscillations with condensation and evaporation, and
presents steady state approximate solutions for free and for pressure
induced oscillations. Resonance criteria and stability are discussed.
Abstract: This paper presents the vibrations suppression of a thermoelastic beam subject to sudden heat input by a distributed piezoelectric actuators. An optimization problem is formulated as the minimization of a quadratic functional in terms of displacement and velocity at a given time and with the least control effort. The solution method is based on a combination of modal expansion and variational approaches. The modal expansion approach is used to convert the optimal control of distributed parameter system into the optimal control of lumped parameter system. By utilizing the variational approach, an explicit optimal control law is derived and the determination of the corresponding displacement and velocity is reduced to solving a set of ordinary differential equations.
Abstract: We developed an effective microfluidic device for photoreactions with low reflectance and good heat conductance. The performance of this microfluidic device was tested by carrying out a photoreactive synthesis of benzopinacol and acetone from benzophenone and 2-propanol. The yield reached 36% with an irradiation time of 469.2 s and was improved by more than 30% when compared to the values obtained by the batch method. Therefore, the microfluidic device was found to be effective for improving the yields of photoreactions.
Abstract: When designing satellites, one of the major issues aside for designing its primary subsystems is to devise its thermal. The thermal management of satellites requires solving different sets of issues with regards to modelling. If the satellite is well conditioned all other parts of the satellite will have higher temperature no matter what. The main issue of thermal modelling for satellite design is really making sure that all the other points of the satellite will be within the temperature limits they are designed. The insertion of power electronics in aerospace technologies is becoming widespread and the modern electronic systems used in space must be reliable and efficient with thermal management unaffected by outer space constraints. Many advanced thermal management techniques have been developed in recent years that have application in high power electronic systems. This paper presents a Three-Dimensional Modal Transmission Line Matrix (3D-TLM) implementation of transient heat flow in space power electronics. In such kind of components heat dissipation and good thermal management are essential. Simulation provides the cheapest tool to investigate all aspects of power handling. The 3DTLM has been successful in modeling heat diffusion problems and has proven to be efficient in terms of stability and complex geometry. The results show a three-dimensional visualisation of self-heating phenomena in the device affected by outer space constraints, and will presents possible approaches for increasing the heat dissipation capability of the power modules.
Abstract: As the demand and prices of various petroleum products have been on the rise in recent years, there is a growing need for alternative fuels. Biodiesel, which consists of alkyl monoesters of fatty acids from vegetable oils and animal fats, is considered as an alternative to petroleum diesel. Biodiesel has comparable performance with that of diesel and has lower brake specific fuel consumption than diesel with significant reduction in emissions of CO, hydrocarbons (HC) and smoke with however, a slight increase in NOx emissions. This paper analyzes the effect of cooled exhaust gas recirculation in the combustion characteristics of a direct injection compression ignition engine using biodiesel blended fuel as opposed to the conventional system. The combustion parameters such as cylinder pressure, heat release rate, delay period and peak pressure were analyzed at various loads. The maximum cylinder pressure reduces as the fraction of biodiesel increases in the blend the maximum rate of pressure rise was found to be higher for diesel at higher engine loads.
Abstract: Evaporator is an important and widely used heat
exchanger in air conditioning and refrigeration industries. Different
methods have been used by investigators to increase the heat transfer
rates in evaporators. One of the passive techniques to enhance heat
transfer coefficient is the application of microfin tubes. The
mechanism of heat transfer augmentation in microfin tubes is
dependent on the flow regime of two-phase flow. Therefore many
investigations of the flow patterns for in-tube evaporation have been
reported in literatures. The gravitational force, surface tension and
the vapor-liquid interfacial shear stress are known as three dominant
factors controlling the vapor and liquid distribution inside the tube. A
review of the existing literature reveals that the previous
investigations were concerned with the two-phase flow pattern for
flow boiling in horizontal tubes [12], [9]. Therefore, the objective of
the present investigation is to obtain information about the two-phase
flow patterns for evaporation of R-134a inside horizontal smooth and
microfin tubes. Also Investigation of heat transfer during flow
boiling of R-134a inside horizontal microfin and smooth tube have
been carried out experimentally The heat transfer coefficients for
annular flow in the smooth tube is shown to agree well with Gungor
and Winterton-s correlation [4]. All the flow patterns occurred in the
test can be divided into three dominant regimes, i.e., stratified-wavy
flow, wavy-annular flow and annular flow. Experimental data are
plotted in two kinds of flow maps, i.e., Weber number for the vapor
versus weber number for the liquid flow map and mass flux versus
vapor quality flow map. The transition from wavy-annular flow to
annular or stratified-wavy flow is identified in the flow maps.
Abstract: Equipment miniaturisation offers several opportunities such as an increased surface-to-volume ratio and higher heat transfer coefficients. However, moving towards small-diameter channels demands extra attention to fouling, reliability and stable operation of the system. The present investigation explores possibilities to enhance the stability of the once-through micro evaporator by reducing its flow boiling induced pressure fluctuations. Experimental comparison shows that the measured reduction factor approaches a theoretically derived value. Pressure fluctuations are reduced by a factor of ten in the solid conical channel and a factor of 15 in the porous conical channel. This presumably leads to less backflow and therefore to a better flow control.
Abstract: The manufacturing transmission line tower parts has
being generated hazardous waste which is required proper disposal
of waste for protection of land pollution. Manufacturing Process in
the manufacturing of steel angle, plates, pipes, channels are passes
through conventional, semi automatic and CNC machines for
cutting, marking, punching, drilling, notching, bending operations.
All fabricated material Coated with thin layer of Zinc in Galvanizing
plant where molten zinc is used for coating. Prior to Galvanizing,
chemical like 33% concentrated HCl Acid, ammonium chloride and
d-oil being used for pretreatment of iron. The bath of water with
sodium dichromate is used for cooling and protection of the
galvanized steel. For the heating purpose the furnace oil burners are
used. These above process the Zinc dross, Zinc ash, ETP sludge and
waste pickled acid generated as hazardous waste. The RPG has
made captive secured land fill site, since 1997 since then it was
using for disposal of hazardous waste after completion of SLF
(Secured land fill) site. The RPG has raised height from ground
level then now it is being used for disposal of waste as he designed
the SLF after in creasing height of from GL it is functional without
leach ate or adverse impacts in the environment.
Abstract: Carrier mobility has become the most important
characteristic of high speed low dimensional devices. Due to
development of very fast switching semiconductor devices, speed of
computer and communication equipment has been increasing day by
day and will continue to do so in future. As the response of any
device depends on the carrier motion within the devices, extensive
studies of carrier mobility in the devices has been established
essential for the growth in the field of low dimensional devices.
Small-signal ac transport of degenerate two-dimensional hot
electrons in GaAs quantum wells is studied here incorporating
deformation potential acoustic, polar optic and ionized impurity
scattering in the framework of heated drifted Fermi-Dirac carrier
distribution. Delta doping is considered in the calculations to
investigate the effects of double delta doping on millimeter and submillimeter
wave response of two dimensional hot electrons in GaAs
nanostructures. The inclusion of delta doping is found to enhance
considerably the two dimensional electron density which in turn
improves the carrier mobility (both ac and dc) values in the GaAs
quantum wells thereby providing scope of getting higher speed
devices in future.
Abstract: Inconel718 has been widely used as a super alloy in aerospace application due to the high strength at elevated temperatures, satisfactory oxidation resistance and heat corrosion resistance. In this study, the Inconel718 has been fabricated using high technology of Metal Injection Molding (MIM) process due to the cost effective technique for producing small, complex and precision parts in high volume compared with conventional method through machining. Through MIM, the binder system is one of the most important criteria in order to successfully fabricate the Inconel718. Even though, the binder system is a temporary, but failure in the selection and removal of the binder system will affect on the final properties of the sintered parts. Therefore, the binder system based on palm oil derivative which is palm stearin has been formulated and developed to replace the conventional binder system. The rheological studies of the mixture between the powder and binders system have been determined properly in order to be successful during injection into injection molding machine. After molding, the binder holds the particles in place. The binder system has to be removed completely through debinding step. During debinding step, solvent debinding and thermal pyrolysis has been used to remove completely of the binder system. The debound part is then sintered to give the required physical and mechanical properties. The results show that the properties of the final sintered parts fulfill the Standard Metal Powder Industries Federation (MPIF) 35 for MIM parts.
Abstract: In elevating performance in competetive sports, an
athlete must continously train in achieving maximum
performance,but needs to pay attention to recovery therapy, that is to
recover from fatigue as well as injury.The correct recovery therapy
will assist in process of recovery and helps in the training in
achieving better performace. Binahong (Anredera cordifolia) was
proven empirically by the locals in assisting speedy recovery from an
injury.Clinical research with lab animals receiving blunt trauma
injury, microscopically shown signs of: 1) redness, 2) heatiness, 3)
swelling and, 4) lack of activity. There is also microscopic indication
of: 1) infiltration of inflame cells (migration of cells to the trauma
area), 2) Cells necrosis, 3) Congestion (as a result of dead red blood
cells), 4) uedema. On administration of Binahong for 3 days, there is
a significant drop of 5% in cell inflammation, 2% increase of
fibroblast (cell membrance) count.Conclutin: Binahong do assist in
reducing cell inflammation and increase counts of cells fibroblast.
Suggestion: In helping athlete's to recover from force injury, we need
study about Binahong's roots to inflammation cell and healing of
injuried cell.
Abstract: This paper is a numerical investigation of a laminar
isothermal plane two dimensional wall jet. Special attention has been
paid to the effect of the inlet conditions at the nozzle exit on the
hydrodynamic and thermal characteristics of the flow. The
behaviour of various fluids evolving in both forced and mixed
convection regimes near a vertical plate plane is carried out. The
system of governing equations is solved with an implicit finite
difference scheme. For numerical stability we use a staggered non
uniform grid. The obtained results show that the effect of the Prandtl
number is significant in the plume region in which the jet flow is
governed by buoyant forces. Further for ascending X values, the
buoyancy forces become dominating, and a certain agreement
between the temperature profiles are observed, which shows that the
velocity profile has no longer influence on the wall temperature
evolution in this region. Fluids with low Prandtl number warm up
more importantly, because for such fluids the effect of heat diffusion
is higher.
Abstract: Nanocrystalline thin film of Na0.1V2O5.nH2O xerogel
obtained by sol gel synthesis was used as gas sensor. Gas sensing
properties of different gases such as hydrogen, petroleum and
humidity were investigated. Applying XRD and TEM the size of the
nanocrystals is found to be 7.5 nm. SEM shows a highly porous
structure with submicron meter-sized voids present throughout the
sample. FTIR measurement shows different chemical groups
identifying the obtained series of gels. The sample was n-type
semiconductor according to the thermoelectric power and electrical
conductivity. It can be seen that the sensor response curves from
130oC to 150oC show a rapid increase in sensitivity for all types of
gas injection, low response values for heating period and the rapid
high response values for cooling period. This result may suggest that
this material is able to act as gas sensor during the heating and
cooling process.
Abstract: A method is presented for using thermo-mechanical fatigue analysis as a tool in the design of automotive heat exchangers. Use of infra-red thermography to measure the real thermal history in the heat exchanger reduces the time necessary for calculating design parameters and improves prediction accuracy. Thermal shocks are the primary cause of heat exchanger damage. Thermo-mechanical simulation is based on the mean behavior of the aluminum tubes used in the heat exchanger. An energetic fatigue criterion is used to detect critical zones.
Abstract: A new analytical model is developed which provides
close-formed solutions for both transient indoor and envelope
temperature changes in buildings. Time-dependent boundary
temperature is presented as Fourier series which can approximate real
weather conditions. The final close-formed solutions are simple,
concise, and comprehensive. The model was compared with
numerical results and good accuracy was obtained. The model can
be used as design and control guidelines in engineering applications
for analysing mechanical heat transfer properties for buildings.
Abstract: Using the finite element analyses, this paper discusses the effects of temperature-dependent material properties on the stress and temperature fields in a cracked metal plate under the electric current load. The practical and complicated results are obtained when the temperature-dependent material properties are adopted in the analysis. If the simplified (temperature-independent) material properties are used, incorrect results will be obtained.
Abstract: The objective of the present work is to conduct
investigations leading to a more complete explanation of single phase
natural convective heat transfer in an enclosure with fin utilizing
nano fluids. The nano fluid used, which is composed of Aluminum
oxide nano particles in suspension of Ethylene glycol, is provided at
various volume fractions. The study is carried out numerically for a
range of Rayleigh numbers, fin heights and aspect ratio. The flow and
temperature distributions are taken to be two-dimensional. Regions
with the same velocity and temperature distributions are identified as
symmetry of sections. One half of such a rectangular region is chosen
as the computational domain taking into account the symmetry about
the fin. Transport equations are modeled by a stream functionvorticity
formulation and are solved numerically by finite-difference
schemes. Comparisons with previously published works on the basis
of special cases are done. Results are presented in the form of
streamline, vector and isotherm plots as well as the variation of local
Nusselt number along the fin under different conditions.
Abstract: This study aims to investigate mechanical behavior of
deep-drawn cups consisting of aluminum (A1050)/ duralumin
(A2017) multi-layered clad structures with micro- and macro-scale
functional gradients. Such multi-layered clad structures are possibly
used for a new type of crash-boxes in automobiles to effectively
absorb the impact forces generated when automobiles having
collisions. The effect of heat treatments on microstructure,
compositional gradient, micro hardness in 2 and 6-layered aluminum/
duralumin clad structures, which were fabricated by hot rolling, have
been investigated. Impact compressive behavior of deep-drawn cups
consisting of such aluminum/ duralumin clad structures has been also
investigated in terms of energy absorption and maximum force.
Deep-drawn cups consisting of 6-layerd clad structures with microand
macro-scale functional gradients exhibit superior properties in
impact compressive tests.
Abstract: Simulation of occlusal function during laboratory
material-s testing becomes essential in predicting long-term
performance before clinical usage. The aim of the study was to assess
the influence of chamfer preparation depth on failure risk of heat
pressed ceramic crowns with and without zirconia framework by
means of finite element analysis. 3D models of maxillary central
incisor, prepared for full ceramic crowns with different depths of the
chamfer margin (between 0.8 and 1.2 mm) and 6-degree tapered
walls together with the overlying crowns were generated using
literature data (Fig. 1, 2). The crowns were designed with and
without a zirconia framework with a thickness of 0.4 mm. For all
preparations and crowns, stresses in the pressed ceramic crown,
zirconia framework, pressed ceramic veneer, and dentin were
evaluated separately. The highest stresses were registered in the
dentin. The depth of the preparations had no significant influence on
the stress values of the teeth and pressed ceramics for the studied
cases, only for the zirconia framework. The zirconia framework
decreases the stress values in the veneer.
Abstract: In hypersonic environments, the aerothermal effect
makes it difficult for the optical side windows of optical guided
missiles to withstand high heat. This produces cracking or breaking,
resulting in an inability to function. This study used computational
fluid mechanics to investigate the external cooling jet conditions of
optical side windows. The turbulent models k-ε and k-ω were
simulated. To be in better accord with actual aerothermal
environments, a thermal radiation model was added to examine
suitable amounts of external coolants and the optical window
problems of aero-thermodynamics. The simulation results indicate that
when there are no external cooling jets, because airflow on the optical
window and the tail groove produce vortices, the temperatures in these
two locations reach a peak of approximately 1600 K. When the
external cooling jets worked at 0.15 kg/s, the surface temperature of
the optical windows dropped to approximately 280 K. When adding
thermal radiation conditions, because heat flux dissipation was faster,
the surface temperature of the optical windows fell from 280 K to
approximately 260 K. The difference in influence of the different
turbulence models k-ε and k-ω on optical window surface temperature
was not significant.