Abstract: The three-time-scale plant model of a wind power
generator, including a wind turbine, a flexible vertical shaft, a Variable
Inertia Flywheel (VIF) module, an Active Magnetic Bearing (AMB)
unit and the applied wind sequence, is constructed. In order to make
the wind power generator be still able to operate as the spindle speed
exceeds its rated speed, the VIF is equipped so that the spindle speed
can be appropriately slowed down once any stronger wind field is
exerted. To prevent any potential damage due to collision by shaft
against conventional bearings, the AMB unit is proposed to regulate
the shaft position deviation. By singular perturbation order-reduction
technique, a lower-order plant model can be established for the
synthesis of feedback controller. Two major system parameter
uncertainties, an additive uncertainty and a multiplicative uncertainty,
are constituted by the wind turbine and the VIF respectively.
Frequency Shaping Sliding Mode Control (FSSMC) loop is proposed
to account for these uncertainties and suppress the unmodeled
higher-order plant dynamics. At last, the efficacy of the FSSMC is
verified by intensive computer and experimental simulations for
regulation on position deviation of the shaft and counter-balance of
unpredictable wind disturbance.
Abstract: Magnesium is used implant material potentially for
non-toxicity to the human body. Due to the excellent
bio-compatibility, Mg alloys is applied to implants avoiding removal
second surgery. However, it is found commercial magnesium alloys
including aluminum has low corrosion resistance, resulting
subcutaneous gas bubbles and consequently the approach as
permanent bio-materials. Generally, Aluminum is known to pollution
substance, and it raises toxicity to nervous system. Therefore
especially Mg-35Zn-3Ca alloy is prepared for new biodegradable
materials in this study. And the pulsed power is used in
constant-current mode of DC power kinds of anodization. Based on
the aforementioned study, it examines corrosion resistance and
biocompatibility by effect of current and frequency variation. The
surface properties and thickness were compared using scanning
electronic microscopy. Corrosion resistance was assessed via
potentiodynamic polarization and the effect of oxide layer on the body
was assessed cell viability. Anodized Mg-35Zn-3Ca alloy has good
biocompatibility in vitro by current and frequency variation.
Abstract: A active inductor in CMOS techonology with a supply voltage of 1.8V is presented. The value of the inductance L can be in the range from 0.12nH to 0.25nH in high frequency(HF). The proposed active inductor is designed in TSMC 0.18-um CMOS technology. The power dissipation of this inductor can retain constant at all operating frequency bands and consume around 20mW from 1.8V power supply. Inductors designed by integrated circuit occupy much smaller area, for this reason,attracted researchers attention for more than decade. In this design we used Advanced Designed System (ADS) for simulating cicuit.
Abstract: Principal Component Analysis (PCA) has many
different important applications especially in pattern detection
such as face detection / recognition. Therefore, for real time
applications, the response time is required to be as small as
possible. In this paper, new implementation of PCA for fast
face detection is presented. Such new implementation is
designed based on cross correlation in the frequency domain
between the input image and eigenvectors (weights).
Simulation results show that the proposed implementation of
PCA is faster than conventional one.
Abstract: RFID (Radio Frequency IDentification) system has
been widely used in our life, such as transport systems, passports,
automotive, animal tracking, human implants, library, and so on.
However, the RFID authentication protocols between RF (Radio
Frequency) tags and the RF readers have been bring about various
privacy problems that anonymity of the tags, tracking, eavesdropping,
and so on. Many researchers have proposed the solution of the
problems. However, they still have the problem, such as location
privacy, mutual authentication. In this paper, we show the problems of
the previous protocols, and then we propose a more secure and
efficient RFID authentication protocol.
Abstract: Road crashes not only claim lives and inflict injuries but also create economic burden to the society due to loss of productivity. The problem of deaths and injuries as a result of road traffic crashes is now acknowledged to be a global phenomenon with authorities in virtually all countries of the world concerned about the growth in the number of people killed and seriously injured on their roads. However, the road crash scenario of a developing country like Bangladesh is much worse comparing with this of developed countries. For developing proper countermeasures it is necessary to identify the factors affecting crash occurrences. The objectives of the study is to examine the effect of district wise road infrastructure, socioeconomic and demographic features on crash occurrence .The unit of analysis will be taken as individual district which has not been explored much in the past. Reported crash data obtained from Bangladesh Road Transport Authority (BRTA) from the year 2004 to 2010 are utilized to develop negative binomial model. The model result will reveal the effect of road length (both paved and unpaved), road infrastructure and several socio economic characteristics on district level crash frequency in Bangladesh.
Abstract: The direct implementation of interleaver functions
in WiMAX is not hardware efficient due to presence of complex
functions. Also the conventional method i.e. using memories for
storing the permutation tables is silicon consuming. This work
presents a 2-D transformation for WiMAX channel interleaver
functions which reduces the overall hardware complexity to
compute the interleaver addresses on the fly. A fully reconfigurable
architecture for address generation in WiMAX
channel interleaver is presented, which consume 1.1 k-gates in
total. It can be configured for any block size and any modulation
scheme in WiMAX. The presented architecture can run at a
frequency of 200 MHz, thus fully supporting high bandwidth
requirements for WiMAX.
Abstract: This paper aims at identifying and analyzing the
knowledge transmission channels in textile and clothing clusters
located in Brazil and in Europe. Primary data was obtained through
interviews with key individuals. The collection of primary data was
carried out based on a questionnaire with ten categories of indicators
of knowledge transmission. Secondary data was also collected
through a literature review and through international organizations
sites. Similarities related to the use of the main transmission channels
of knowledge are observed in all cases. The main similarities are:
influence of suppliers of machinery, equipment and raw materials;
imitation of products and best practices; training promoted by
technical institutions and businesses; and cluster companies being
open to acquire new knowledge. The main differences lie in the
relationship between companies, where in Europe the intensity of this
relationship is bigger when compared to Brazil. The differences also
occur in importance and frequency of the relationship with the
government, with the cultural environment, and with the activities of
research and development. It is also found factors that reduce the
importance of geographical proximity in transmission of knowledge,
and in generating trust and the establishment of collaborative
behavior.
Abstract: The main purpose of this study is to provide a detailed
statistical overview of the time and regional distribution, relative
timing occurrence of economic crises and government changes in 51
economies over the 1990–2007 periods. At the same time, the
predictive power of the economic crises on set government changes
will be examined using “signal approach".
The result showed that the percentage of government changes is
highest in transition economies (86 percent of observations) and
lowest in Latin American economies (39 percent of observations).
The percentages of government changes are same in both developed
and developing countries (43 percent of observations). However,
average crises per year (frequency of crises) are higher (lower) in
developing (developed) countries than developed (developing)
countries. Also, the predictive power of economic crises about the
onset of a government change is highest in Transition economies (81
percent) and lowest in Latin American countries (30 percent). The
predictive power of economic crises in developing countries (43
percent) is lower than developed countries (55 percent).
Abstract: RF performance of SOI CMOS device has attracted
significant amount of interest recently. In order to improve RF
parameters, Strained Si/Relaxed Si0.8Ge0.2 investigated as a
replacement for Si technology .Enhancement of carrier mobility
associated with strain engineering makes Strained Si a promising
candidate for improving RF performance of CMOS technology.
From the simulation, the cut-off frequency is estimated to be 224
GHZ, whereas in SOI at similar bias is about 188 GHZ. Therefore,
Strained Si exhibits 19% improvement in cut-off frequency over
similar Si counterpart. In this paper, Ion/Ioff ratio is studied as one of
the key parameters in logic and digital application. Strained Si/SiGe
demonstrates better Ion/Ioff characteristic than SOI, in similar channel
length of 100 nm.Another important key analog figures of merit such
as Early Voltage (VEA) ,transconductance vs drain current (gm /Ids)
are studied. They introduce the efficiency of the devices to convert
dc power into ac frequency.
Abstract: Single-pole switching scheme is widely used in the
Extra High Voltage system. However, the substantial negativesequence
current injected to the turbine-generators imposes the
electromagnetic (E/M) torque of double system- frequency
components during the dead time (between single-pole clearing and
line reclosing). This would induce supersynchronous resonance
(SPSR) torque amplifications on low pressure turbine generator
blades and even lead to fatigue damage. This paper proposes the
design of a mechanical filter (MF) with natural frequency close to
double-system frequency. From the simulation results, it is found that
such a filter not only successfully damps the resonant effect, but also
has the characteristics of feasibility and compact.
Abstract: The modern telecommunication industry demands
higher capacity networks with high data rate. Orthogonal frequency
division multiplexing (OFDM) is a promising technique for high data
rate wireless communications at reasonable complexity in wireless
channels. OFDM has been adopted for many types of wireless
systems like wireless local area networks such as IEEE 802.11a, and
digital audio/video broadcasting (DAB/DVB). The proposed research
focuses on a concatenated coding scheme that improve the
performance of OFDM based wireless communications. It uses a
Redundant Residue Number System (RRNS) code as the outer code
and a convolutional code as the inner code. Here, a direct conversion
of analog signal to residue domain is done to reduce the conversion
complexity using sigma-delta based parallel analog-to-residue
converter. The bit error rate (BER) performances of the proposed
system under different channel conditions are investigated. These
include the effect of additive white Gaussian noise (AWGN),
multipath delay spread, peak power clipping and frame start
synchronization error. The simulation results show that the proposed
RRNS-Convolutional concatenated coding (RCCC) scheme provides
significant improvement in the system performance by exploiting the
inherent properties of RRNS.
Abstract: Crucial information barely visible to the human eye is
often embedded in a series of low resolution images taken of the
same scene. Super resolution reconstruction is the process of
combining several low resolution images into a single higher
resolution image. The ideal algorithm should be fast, and should add
sharpness and details, both at edges and in regions without adding
artifacts. In this paper we propose a super resolution blind
reconstruction technique for linearly degraded images. In our
proposed technique the algorithm is divided into three parts an image
registration, wavelets based fusion and an image restoration. In this
paper three low resolution images are considered which may sub
pixels shifted, rotated, blurred or noisy, the sub pixel shifted images
are registered using affine transformation model; A wavelet based
fusion is performed and the noise is removed using soft thresolding.
Our proposed technique reduces blocking artifacts and also
smoothens the edges and it is also able to restore high frequency
details in an image. Our technique is efficient and computationally
fast having clear perspective of real time implementation.
Abstract: The operation performance of a valveless micro-pump
is strongly dependent on the shape of connected nozzle/diffuser and
Reynolds number. The aims of present work are to compare the
performance curves of micropump with the original straight
nozzle/diffuser and contoured nozzle/diffuser under different back
pressure conditions. The tested valveless micropumps are assembled
of five pieces of patterned PMMA plates with hot-embracing
technique. The structures of central chamber, the inlet/outlet
reservoirs and the connected nozzle/diffuser are fabricated with laser
cutting machine. The micropump is actuated with circular-type PZT
film embraced on the bottom of central chamber. The deformation of
PZT membrane with various input voltages is measured with a
displacement laser probe. A simple testing facility is also constructed
to evaluate the performance curves for comparison.
In order to observe the evaluation of low Reynolds number
multiple vortex flow patterns within the micropump during suction
and pumping modes, the unsteady, incompressible laminar
three-dimensional Reynolds-averaged Navier-Stokes equations are
solved. The working fluid is DI water with constant thermo-physical
properties. The oscillating behavior of PZT film is modeled with the
moving boundary wall in way of UDF program. With the dynamic
mesh method, the instants pressure and velocity fields are obtained
and discussed.Results indicated that the volume flow rate is not
monotony increased with the oscillating frequency of PZT film,
regardless of the shapes of nozzle/diffuser. The present micropump
can generate the maximum volume flow rate of 13.53 ml/min when
the operation frequency is 64Hz and the input voltage is 140 volts.
The micropump with contoured nozzle/diffuser can provide 7ml/min
flow rate even when the back pressure is up to 400 mm-H2O. CFD
results revealed that the flow central chamber was occupied with
multiple pairs of counter-rotating vortices during suction and
pumping modes. The net volume flow rate over a complete
oscillating periodic of PZT
Abstract: This study was investigated on sampling and
analyzing water quality in water reservoir & water tower installed in
two kind of residential buildings and school facilities. Data of water
quality was collected for correlation analysis with frequency of
sanitization of water reservoir through questioning managers of
building about the inspection charts recorded on equipment for water
reservoir. Statistical software packages (SPSS) were applied to the
data of two groups (cleaning frequency and water quality) for
regression analysis to determine the optimal cleaning frequency of
sanitization. The correlation coefficient (R) in this paper represented
the degree of correlation, with values of R ranging from +1 to -1.After
investigating three categories of drinking water users; this study found
that the frequency of sanitization of water reservoir significantly
influenced the water quality of drinking water. A higher frequency of
sanitization (more than four times per 1 year) implied a higher quality
of drinking water. Results indicated that sanitizing water reservoir &
water tower should at least twice annually for achieving the aim of
safety of drinking water.
Abstract: An active RC filters with a 880 / 1760 MHz dual bandwidth tuning ability is present for 60 GHz unlicensed band applications. A third order Butterworth low-pass filter utilizes two Cherry-Hooper amplifiers to satisfy the very high bandwidth requirements of an amplifier. The low-pass filter is fabricated in 90nm standard CMOS process. Drawing 6.7 mW from 1.2 V power supply, the low frequency gains of the filter are -2.5 and -4.1 dB, and the output third order intercept points (OIP3) are +2.2 and +1.9 dBm for the single channel and channel bonding conditions, respectively.
Abstract: The application of a high frequency signal injection method as speed and position observer in PMSM drives has been a research focus. At present, the precision of this method is nearly good as that of ten-bit encoder. But there are some questions for estimating position polarity. Based on high frequency signal injection, this paper presents a method to compensate position polarity for permanent magnet synchronous motor (PMSM). Experiments were performed to test the effectiveness of the proposed algorithm and results present the good performance.
Abstract: We investigated oxidative DNA damage caused by
radio frequency radiation using 8-oxo-7, 8-dihydro-2'-
deoxyguanosine (8-oxodG) generated in mice tissues after exposure
to 900 MHz mobile phone radio frequency in three independent
experiments. The RF was generated by a Global System for Mobile
Communication (GSM) signal generator. The radio frequency field
was adjusted to 25 V/m. The whole body specific absorption rate
(SAR) was 1.0 W/kg. Animals were exposed to this field for 30 min
daily for 30 days. 24 h post-exposure, blood serum, brain and spleen
were removed and DNA was isolated. Enzyme-linked
immunosorbent assay (ELISA) was used to measure 8-oxodG
concentration. All animals survived the whole experimental period.
The body weight of animals did not change significantly at the end of
the experiment. No statistically significant differences observed in
the levels of oxidative stress. Our results are not in favor of the
hypothesis that 900 MHz RF induces oxidative damage.
Abstract: This paper presents the region based segmentation method for ultrasound images using local statistics. In this segmentation approach the homogeneous regions depends on the image granularity features, where the interested structures with dimensions comparable to the speckle size are to be extracted. This method uses a look up table comprising of the local statistics of every pixel, which are consisting of the homogeneity and similarity bounds according to the kernel size. The shape and size of the growing regions depend on this look up table entries. The algorithms are implemented by using connected seeded region growing procedure where each pixel is taken as seed point. The region merging after the region growing also suppresses the high frequency artifacts. The updated merged regions produce the output in formed of segmented image. This algorithm produces the results that are less sensitive to the pixel location and it also allows a segmentation of the accurate homogeneous regions.
Abstract: Nigerian bread is baked with vitamin A fortified wheat flour. Study aimed at determining its contribution to preschoolers- vitamin A nutriture. A cross-sectional/experimental study was carried out in four poor-urban Local Government Areas (LGAs) of Metropolitan Lagos, Nigeria. A pretested food frequency questionnaire was administered to randomly selected mothers of 1600 preschoolers (24-59 months). Retinyl Palmitate content of fourteen bread samples randomly collected from bakeries in all LGAs was analyzed at 0 and 5 days at 25oC using High Performance Liquid Chromatography. Data analysis was done at p