Abstract: This paper discusses the undesirable charge transfer
through the parasitic capacitances of the input transistors in a
multi-inputs voltage sense amplifier. Its intrinsic rail-to-rail voltage
transitions at the output nodes inevitably disturb the input sides
through the capacitive coupling between the outputs and inputs. Then,
it can possible degrade the stabilities of the reference voltage levels.
Moreover, it becomes more serious in multi-channel systems by
altering them for other channels, and so degrades the linearity of the
overall systems. In order to alleviate the internal node voltage
transition, the internal node stabilization techniques are proposed. It
achieves 45% and 40% improvements for node stabilization and input
referred disturbance, respectively.
Abstract: This paper discusses the undesirable charge transfer by the parasitic capacitances of the input transistors in a voltage sense amplifier. Due to its intrinsic rail-to-rail voltage transition, the input sides are inevitably disturbed. It can possible disturb the stabilities of the reference voltage levels. Moreover, it becomes serious in multi-channel systems by altering them for other channels, and so degrades the linearity of the systems. In order to alleviate the internal node voltage transition, the internal node stabilization technique is proposed by utilizing an additional biasing circuit. It achieves 47% and 43% improvements for node stabilization and input referred disturbance, respectively.
Abstract: It is very effective way to utilize a very wide tunable filter in co-existing multi-standards wireless communications environment. Especially, as the long term evolution (LTE) communication era has come, the multi-band coverage is one of the important features required for the RF components. In this paper, we present the frequency conversion technique, and so generate two types of RF filters which are specially designed for the superb tunable ability to support multiple wireless communication standards. With the help of a complex mixing structure, the inherent image signal is suppressed. The RF band-pass filter (BPF) and notch filter achieve 1.8dB and 1.6dB insertion losses and 18 dB and 17 dB attenuations, respectively. The quality factor show greater than 30.
Abstract: This paper presents the 20-GHz fractional PLL (Phase
Locked Loop) circuit for the next generation Wi-Fi by using 90 nm
TSMC process. The newly suggested millimeter wave 16/17
pre-scalar is designed and verified by measurement to make the
fractional PLL having a low quantization noise. The operational
bandwidth of the 60 GHz system is 15 % of the carrier frequency
which requires large value of Kv (VCO control gain) resulting in
degradation of phase noise. To solve this problem, this paper adopts
AFC (Automatic Frequency Controller) controlled 4-bit millimeter
wave VCO with small value of Kv. Also constant Kv is implemented
using 4-bit varactor bank. The measured operational bandwidth is 18.2
~ 23.2 GHz which is 25 % of the carrier frequency. The phase noise of
-58 and -96.2 dBc/Hz at 100 KHz and 1 MHz offset is measured
respectively. The total power consumption of the PLL is only 30 mW.
Abstract: An active RC filters with a 880 / 1760 MHz dual bandwidth tuning ability is present for 60 GHz unlicensed band applications. A third order Butterworth low-pass filter utilizes two Cherry-Hooper amplifiers to satisfy the very high bandwidth requirements of an amplifier. The low-pass filter is fabricated in 90nm standard CMOS process. Drawing 6.7 mW from 1.2 V power supply, the low frequency gains of the filter are -2.5 and -4.1 dB, and the output third order intercept points (OIP3) are +2.2 and +1.9 dBm for the single channel and channel bonding conditions, respectively.
Abstract: A way of generating millimeter wave I/Q signal using inductive resonator matched poly-phase filter is suggested. Normally the poly-phase filter generates quite accurate I/Q phase and magnitude but the loss of the filter is considerable due to series connection of passive RC components. This loss term directly increases system noise figure when the poly-phase filter is used in RF Front-end. The proposed matching method eliminates above mentioned loss and in addition provides gain on the passive filter. The working algorithm is illustrated by mathematical analysis. The generated I/Q signal is used in implementing millimeter wave phase shifter for the 60 GHz communication system to verify its effectiveness. The circuit is fabricated in 90 nm TSMC RF CMOS process under 1.2 V supply voltage. The measurement results showed that the suggested method improved gain by 6.5 dB and noise by 2.3 dB. The summary of the proposed I/Q generation is compared with previous works.