Abstract: Optimal load shedding (LS) design as an emergency plan is one of the main control challenges posed by emerging new uncertainties and numerous distributed generators including renewable energy sources in a modern power system. This paper presents an overview of the key issues and new challenges on optimal LS synthesis concerning the integration of wind turbine units into the power systems. Following a brief survey on the existing LS methods, the impact of power fluctuation produced by wind powers on system frequency and voltage performance is presented. The most LS schemas proposed so far used voltage or frequency parameter via under-frequency or under-voltage LS schemes. Here, the necessity of considering both voltage and frequency indices to achieve a more effective and comprehensive LS strategy is emphasized. Then it is clarified that this problem will be more dominated in the presence of wind turbines.
Abstract: The fine structure of supercavitation in the wake of a
symmetrical cylinder is studied with high-speed video cameras. The
flow is observed in a cavitation tunnel at the speed of 8m/sec when the
sidewall and the wake are partially filled with the massive cavitation
bubbles. The present experiment observed that a two-dimensional
ripple wave with a wave length of 0.3mm is propagated in a
downstream direction, and then abruptly increases to a thicker
three-dimensional layer. IR-photography recorded that the wakes
originated from the horseshoe vortexes alongside the cylinder. The
wake was developed to inside the dead water zone, which absorbed the
bubbly wake propelled from the separated vortices at the center of the
cylinder. A remote sensing classification technique (maximum most
likelihood) determined that the surface porosity was 0.2, and the mean
speed in the mixed wake was 7m/sec. To confirm the existence of
two-dimensional wave motions in the interface, the experiments were
conducted at a very low frequency, and showed similar gravity waves
in both the upper and lower interfaces.
Abstract: Multi-user interference (MUI) is the main reason of system deterioration in the Spectral Amplitude Coding Optical Code Division Multiple Access (SAC-OCDMA) system. MUI increases with the number of simultaneous users, resulting into higher probability bit rate and limits the maximum number of simultaneous users. On the other hand, Phase induced intensity noise (PIIN) problem which is originated from spontaneous emission of broad band source from MUI severely limits the system performance should be addressed as well. Since the MUI is caused by the interference of simultaneous users, reducing the MUI value as small as possible is desirable. In this paper, an extensive study for the system performance specified by MUI and PIIN reducing is examined. Vectors Combinatorial (VC) codes families are adopted as a signature sequence for the performance analysis and a comparison with reported codes is performed. The results show that, when the received power increases, the PIIN noise for all the codes increases linearly. The results also show that the effect of PIIN can be minimized by increasing the code weight leads to preserve adequate signal to noise ratio over bit error probability. A comparison study between the proposed code and the existing codes such as Modified frequency hopping (MFH), Modified Quadratic- Congruence (MQC) has been carried out.
Abstract: A new code for spectral-amplitude coding optical
code-division multiple-access system is proposed called Random
diagonal (RD) code. This code is constructed using code segment and
data segment. One of the important properties of this code is that the
cross correlation at data segment is always zero, which means that
Phase Intensity Induced Noise (PIIN) is reduced. For the performance
analysis, the effects of phase-induced intensity noise, shot noise, and
thermal noise are considered simultaneously. Bit-error rate (BER)
performance is compared with Hadamard and Modified Frequency
Hopping (MFH) codes. It is shown that the system using this new
code matrices not only suppress PIIN, but also allows larger number
of active users compare with other codes. Simulation results shown
that using point to point transmission with three encoded channels,
RD code has better BER performance than other codes, also its found
that at 0 dbm PIIN noise are 10-10 and 10-11 for RD and MFH
respectively.
Abstract: Vibration of thin cylindrical shells made of a
functionally gradient material composed of stainless steel and nickel
is presented. The effects of the FGM configuration are studied by
studying the frequencies of FG cylindrical shells. In this case FG
cylindrical shell has Nickel on its outer surface and stainless steel on
its inner surface. The study is carried out based on third order shear
deformation shell theory. The objective is to study the natural
frequencies, the influence of constituent volume fractions and the
effects of configurations of the constituent materials on the
frequencies. The properties are graded in the thickness direction
according to the volume fraction power-law distribution. Results are
presented on the frequency characteristics, the influence of the
constituent various volume fractions on the frequencies.
Abstract: The main aim of Supply Chain Management (SCM) is
to produce, distribute, logistics and deliver goods and equipment in
right location, right time, right amount to satisfy costumers, with
minimum time and cost waste. So implementing techniques that
reduce project time and cost, and improve productivity and
performance is very important. Emerging technologies such as the
Radio Frequency Identification (RFID) are now making it possible to
automate supply chains in a real time manner and making them more
efficient than the simple supply chain of the past for tracing and
monitoring goods and products and capturing data on movements of
goods and other events. This paper considers concepts, components
and RFID technology characteristics by concentration of warehouse
and inventories management. Additionally, utilization of RFID in the
role of improving information management in supply chain is
discussed. Finally, the facts of installation and this technology-s
results in direction with warehouse and inventory management and
business development will be presented.
Abstract: Construction projects generally take place in
uncontrolled and dynamic environments where construction waste is
a serious environmental problem in many large cities. The total
amount of waste and carbon dioxide emissions from transportation
vehicles are still out of control due to increasing construction
projects, massive urban development projects and the lack of
effective tools for minimizing adverse environmental impacts in
construction. This research is about utilization of the integrated
applications of automated advanced tracking and data storage
technologies in the area of environmental management to monitor
and control adverse environmental impacts such as construction
waste and carbon dioxide emissions. Radio Frequency Identification
(RFID) integrated with the Global Position System (GPS) provides
an opportunity to uniquely identify materials, components, and
equipments and to locate and track them using minimal or no worker
input. The transmission of data to the central database will be carried
out with the help of Global System for Mobile Communications
(GSM).
Abstract: In this paper a study on the vibration of thin
cylindrical shells with ring supports and made of functionally graded
materials (FGMs) composed of stainless steel and nickel is presented.
Material properties vary along the thickness direction of the shell
according to volume fraction power law. The cylindrical shells have
ring supports which are arbitrarily placed along the shell and impose
zero lateral deflections. The study is carried out based on third order
shear deformation shell theory (T.S.D.T). The analysis is carried out
using Hamilton-s principle. The governing equations of motion of
FGM cylindrical shells are derived based on shear deformation
theory. Results are presented on the frequency characteristics,
influence of ring support position and the influence of boundary
conditions. The present analysis is validated by comparing results
with those available in the literature.
Abstract: A hardware efficient, multi mode, re-configurable
architecture of interleaver/de-interleaver for multiple standards,
like DVB, WiMAX and WLAN is presented. The interleavers
consume a large part of silicon area when implemented by using
conventional methods as they use memories to store permutation
patterns. In addition, different types of interleavers in different
standards cannot share the hardware due to different construction
methodologies. The novelty of the work presented in this paper is
threefold: 1) Mapping of vital types of interleavers including
convolutional interleaver onto a single architecture with flexibility
to change interleaver size; 2) Hardware complexity for channel
interleaving in WiMAX is reduced by using 2-D realization of the
interleaver functions; and 3) Silicon cost overheads reduced by
avoiding the use of small memories. The proposed architecture
consumes 0.18mm2 silicon area for 0.12μm process and can
operate at a frequency of 140 MHz. The reduced complexity helps
in minimizing the memory utilization, and at the same time
provides strong support to on-the-fly computation of permutation
patterns.
Abstract: In this paper, we present the design and experimental
evaluation of complementary energy path adiabatic logic (CEPAL)
based 1 bit full adder circuit. A simulative investigation on the
proposed full adder has been done using VIRTUOSO SPECTRE
simulator of cadence in 0.18μm UMC technology and its
performance has been compared with the conventional CMOS full
adder circuit. The CEPAL based full adder circuit exhibits the energy
saving of 70% to the conventional CMOS full adder circuit, at 100
MHz frequency and 1.8V operating voltage.
Abstract: Heart-s electric field can be measured anywhere on
the surface of the body (ECG). When individuals touch, one person-s
ECG signal can be registered in other person-s EEG and elsewhere
on his body. Now, the aim of this study was to test the hypothesis
that physical contact (hand-holding) of two persons changes their
heart rate variability. Subjects were sixteen healthy female (age: 20-
26) which divided into eight sets. In each sets, we had two friends
that they passed intimacy test of J.sternberg. ECG of two subjects
(each set) acquired for 5 minutes before hand-holding (as control
group) and 5 minutes during they held their hands (as experimental
group). Then heart rate variability signals were extracted from
subjects' ECG and analyzed in linear feature space (time and
frequency domain) and nonlinear feature space. Considering the
results, we conclude that physical contact (hand-holding of two
friends) increases parasympathetic activity, as indicate by increase
SD1, SD1/SD2, HF and MF power (p
Abstract: This paper presents a novel approach for tuning unified power flow controller (UPFC) based damping controller in order to enhance the damping of power system low frequency oscillations. The design problem of damping controller is formulated as an optimization problem according to the eigenvalue-based objective function which is solved using iteration particle swarm optimization (IPSO). The effectiveness of the proposed controller is demonstrated through eigenvalue analysis and nonlinear time-domain simulation studies under a wide range of loading conditions. The simulation study shows that the designed controller by IPSO performs better than CPSO in finding the solution. Moreover, the system performance analysis under different operating conditions show that the δE based controller is superior to the mB based controller.
Abstract: This paper deals with the tuning of parameters for Automatic Generation Control (AGC). A two area interconnected hydrothermal system with PI controller is considered. Genetic Algorithm (GA) and Particle Swarm optimization (PSO) algorithms have been applied to optimize the controller parameters. Two objective functions namely Integral Square Error (ISE) and Integral of Time-multiplied Absolute value of the Error (ITAE) are considered for optimization. The effectiveness of an objective function is considered based on the variation in tie line power and change in frequency in both the areas. MATLAB/SIMULINK was used as a simulation tool. Simulation results reveal that ITAE is a better objective function than ISE. Performances of optimization algorithms are also compared and it was found that genetic algorithm gives better results than particle swarm optimization algorithm for the problems of AGC.
Abstract: The prediction of financial time series is a very
complicated process. If the efficient market hypothesis holds, then the predictability of most financial time series would be a rather
controversial issue, due to the fact that the current price contains already all available information in the market. This paper extends
the Adaptive Neuro Fuzzy Inference System for High Frequency
Trading which is an expert system that is capable of using fuzzy reasoning combined with the pattern recognition capability of neural networks to be used in financial forecasting and trading in high
frequency. However, in order to eliminate unnecessary input in the
training phase a new event based volatility model was proposed.
Taking volatility and the scaling laws of financial time series into consideration has brought about the development of the Intraday Seasonality Observation Model. This new model allows the observation of specific events and seasonalities in data and subsequently removes any unnecessary data. This new event based
volatility model provides the ANFIS system with more accurate input
and has increased the overall performance of the system.
Abstract: Higher-order Statistics (HOS), also known as
cumulants, cross moments and their frequency domain counterparts,
known as poly spectra have emerged as a powerful signal processing
tool for the synthesis and analysis of signals and systems. Algorithms
used for the computation of cross moments are computationally
intensive and require high computational speed for real-time
applications. For efficiency and high speed, it is often advantageous
to realize computation intensive algorithms in hardware. A promising
solution that combines high flexibility together with the speed of a
traditional hardware is Field Programmable Gate Array (FPGA). In
this paper, we present FPGA-based parallel architecture for the
computation of third-order cross moments. The proposed design is
coded in Very High Speed Integrated Circuit (VHSIC) Hardware
Description Language (VHDL) and functionally verified by
implementing it on Xilinx Spartan-3 XC3S2000FG900-4 FPGA.
Implementation results are presented and it shows that the proposed
design can operate at a maximum frequency of 86.618 MHz.
Abstract: This research paper presents some methods to assess the performance of Wigner Ville Distribution for Time-Frequency representation of non-stationary signals, in comparison with the other representations like STFT, Spectrogram etc. The simultaneous timefrequency resolution of WVD is one of the important properties which makes it preferable for analysis and detection of linear FM and transient signals. There are two algorithms proposed here to assess the resolution and to compare the performance of signal detection. First method is based on the measurement of area under timefrequency plot; in case of a linear FM signal analysis. A second method is based on the instantaneous power calculation and is used in case of transient, non-stationary signals. The implementation is explained briefly for both methods with suitable diagrams. The accuracy of the measurements is validated to show the better performance of WVD representation in comparison with STFT and Spectrograms.
Abstract: This paper describes the design of a programmable
FSK-modulator based on VCO and its implementation in 0.35m
CMOS process. The circuit is used to transmit digital data at
100Kbps rate in the frequency range of 400-600MHz. The design
and operation of the modulator is discussed briefly. Further the
characteristics of PLL, frequency synthesizer, VCO and the whole
design are elaborated. The variation among the proposed and tested
specifications is presented. Finally, the layout of sub-modules, pin
configurations, final chip and test results are presented.
Abstract: Nowadays there are several grid connected converter
in the grid system. These grid connected converters are generally the
converters of renewable energy sources, industrial four quadrant
drives and other converters with DC link. These converters are
connected to the grid through a three phase bridge. The standards
prescribe the maximal harmonic emission which could be easily
limited with high switching frequency. The increased switching
losses can be reduced to the half with the utilization of the wellknown
Flat-top modulation. The suggested control method is the
expansion of the Flat-top modulation with which the losses could be
also reduced to the half compared to the Flat-top modulation.
Comparing to traditional control these requirements can be
simultaneously satisfied much better with the DLF (DC Link
Floating) method.
Abstract: In this paper, an accurate theoretical analysis for the achievable average channel capacity (in the Shannon sense) per user of a hybrid cellular direct-sequence/fast frequency hopping code-division multiple-access (DS/FFH-CDMA) system operating in a Rayleigh fading environment is presented. The analysis covers the downlink operation and leads to the derivation of an exact mathematical expression between the normalized average channel capacity available to each system-s user, under simultaneous optimal power and rate adaptation and the system-s parameters, as the number of hops per bit, the processing gain applied, the number of users per cell and the received signal-tonoise power ratio over the signal bandwidth. Finally, numerical results are presented to illustrate the proposed mathematical analysis.
Abstract: In an Orthogonal Frequency Division Multiplexing (OFDM) systems, the Peak to Average power Ratio (PAR) is high. The clipping signal scheme is a useful and simple method to reduce the PAR. However, it introduces additional noise that degrades the systems performance. We propose an oversampling scheme to deal with the received signal in order to reduce the clipping noise by using Finite Impulse Response (FIR) filter. Coefficients of filter are obtained by correlation function of the received signal and the oversampling information at receiver. The performance of the proposed technique is evaluated for frequency selective channel. Results show that the proposed scheme can mitigate the clipping noise significantly for OFDM systems and in order to maintain the system's capacity, the clipping ratio should be larger than 2.5.