Abstract: The IEEE802.16 standard which has emerged as
Broadband Wireless Access (BWA) technology, promises to deliver
high data rate over large areas to a large number of subscribers in the
near future. This paper analyze the effect of overheads over capacity
of downlink (DL) of orthogonal frequency division multiple access
(OFDMA)–based on the IEEE802.16e mobile WiMAX system with
and without overheads. The analysis focuses in particular on the
impact of Adaptive Modulation and Coding (AMC) as well as
deriving an algorithm to determine the maximum numbers of
subscribers that each specific WiMAX sector may support. An
analytical study of the WiMAX propagation channel by using Cost-
231 Hata Model is presented. Numerical results and discussion
estimated by using Matlab to simulate the algorithm for different
multi-users parameters.
Abstract: We have fabricated a-IGZO TFT and investigated the
stability under positive DC and AC bias stress. The threshold voltage
of a-IGZO TFT shifts positively under those biases, and that reduces
on-current. For this reason, conventional shift-register circuit
employing TFTs which stressed by positive bias will be unstable, may
do not work properly. We have designed a new 6-transistor
shift-register, which has less transistors than prior circuits. The TFTs
of the proposed shift-register are not suffering from positive DC or AC
stress, mainly kept unbiased. Despite the compact design, the stable
output signal was verified through the SPICE simulation even under
RC delay of clock signal.
Abstract: Trust and Energy consumption is the most challenging
issue in routing protocol design for Mobile ad hoc networks
(MANETs), since mobile nodes are battery powered and nodes
behaviour are unpredictable. Furthermore replacing and recharging
batteries and making nodes co-operative is often impossible in
critical environments like military applications. In this paper, we
propose a trust based energy aware routing model in MANET.
During route discovery, node with more trust and maximum energy
capacity is selected as a router based on a parameter called
'Reliability'. Route request from the source is accepted by a node
only if its reliability is high. Otherwise, the route request is
discarded. This approach forms a reliable route from source to
destination thus increasing network life time, improving energy
utilization and decreasing number of packet loss during transmission.
Abstract: Today, incorrect use of lands and land use changes,
excessive grazing, no suitable using of agricultural farms, plowing on
steep slopes, road construct, building construct, mine excavation etc
have been caused increasing of soil erosion and sediment yield. For
erosion and sediment estimation one can use statistical and empirical
methods. This needs to identify land unit map and the map of
effective factors. However, these empirical methods are usually time
consuming and do not give accurate estimation of erosion. In this
study, we applied GIS techniques to estimate erosion and sediment of
Menderjan watershed at upstream Zayandehrud river in center of
Iran. Erosion faces at each land unit were defined on the basis of land
use, geology and land unit map using GIS. The UTM coordinates of
each erosion type that showed more erosion amounts such as rills and
gullies were inserted in GIS using GPS data. The frequency of
erosion indicators at each land unit, land use and their sediment yield
of these indices were calculated. Also using tendency analysis of
sediment yield changes in watershed outlet (Menderjan hydrometric
gauge station), was calculated related parameters and estimation
errors. The results of this study according to implemented watershed
management projects can be used for more rapid and more accurate
estimation of erosion than traditional methods. These results can also
be used for regional erosion assessment and can be used for remote
sensing image processing.
Abstract: GFRG(Glass Fiber Reinforced Gypsum) wall is a green product which can erect a building fast in prefabricated method, but its application to high-rise residential buildings is limited for its poor lateral stiffness. This paper has proposed a modification to GFRG walls structure to increase its lateral stiffness, which aiming to erect small high-rise residential buildings as load-bearing walls. The elastic finite element analysis to it has shown the lateral deformation feature and the distributions of the axial force and the shear force. The analysis results show that the new GFRG reinforced concrete wall can be used for small high-rise residential buildings.
Abstract: This paper investigates vortex shedding processes
occurring at the end of a stack of parallel plates, due to an oscillating
flow induced by an acoustic standing wave within an acoustic
resonator. Here, Particle Image Velocimetry (PIV) is used to quantify
the vortex shedding processes within an acoustic cycle
phase-by-phase, in particular during the “ejection" of the fluid out of
the stack. Standard hot-wire anemometry measurement is also applied
to detect the velocity fluctuations near the end of the stack.
Combination of these two measurement techniques allowed a detailed
analysis of the vortex shedding phenomena. The results obtained show
that, as the Reynolds number varies (by varying the plate thickness
and drive ratio), different flow patterns of vortex shedding are
observed by the PIV measurement. On the other hand, the
time-dependent hot-wire measurements allow obtaining detailed
frequency spectra of the velocity signal, used for calculating
characteristic Strouhal numbers. The impact of the plate thickness and
the Reynolds number on the vortex shedding pattern has been
discussed. Furthermore, a detailed map of the relationship between the
Strouhal number and Reynolds number has been obtained and
discussed.
Abstract: The iris recognition technology is the most accurate,
fast and less invasive one compared to other biometric techniques
using for example fingerprints, face, retina, hand geometry, voice or
signature patterns. The system developed in this study has the
potential to play a key role in areas of high-risk security and can
enable organizations with means allowing only to the authorized
personnel a fast and secure way to gain access to such areas. The
paper aim is to perform the iris region detection and iris inner and
outer boundaries localization. The system was implemented on
windows platform using Visual C# programming language. It is easy
and efficient tool for image processing to get great performance
accuracy. In particular, the system includes two main parts. The first
is to preprocess the iris images by using Canny edge detection
methods, segments the iris region from the rest of the image and
determine the location of the iris boundaries by applying Hough
transform. The proposed system tested on 756 iris images from 60
eyes of CASIA iris database images.
Abstract: Australia, while being a large and eager consumer of
innovative and cutting edge Information and Communication
Technologies (ICT), continues to struggle to remain a leader in
Technological Innovation. This paper has two main contributions to
address certain aspects of this complex issue. The first being the
current findings of an ongoing research project on Information and
Innovation Management in the Australian Information and
Communication Technologies (ICT) sector. The major issues being
considered by the project include: investigation of the possible
inherent entrepreneurial nature of ICT; how to foster ICT innovation;
and examination of the inherent difficulties currently found within
the ICT industry of Australia in regards to supporting the
development of innovative and creative ideas. The second major
contribution is details of the I.-C.A.N. (Innovation by Collaborative
Anonymous Networking) software application information
management tool created and evolving in our research group. I-CAN,
besides having a positive reinforcement acronym, is aimed at
facilitating productive collaborative innovation in an Australian
workplace. Such a work environment is frequently subjected to
cultural influences such as the 'tall poppy syndrome' and 'negative'
or 'unconstructive' peer-pressure. There influences are frequently
seen as inhibitors to employee participation, entrepreneurship and
innovation.
Abstract: KSLV-I(Korea Space Launch Vehicle-I) is designed as
a launch vehicle to enter a 100 kg-class satellite to the LEO(Low Earth
Orbit). Attitude angles of the upper-stage, including roll, pitch and
yaw are controlled by the cold gas thruster system using nitrogen gas.
The cold gas thruster is an actuator in the RCS(Reaction Control
System). To design an attitude controller for the upper-stage, thrust
measurement in vacuum condition is required. In this paper, the new
thrust measurement system and calibration mechanism are developed
and measurement errors and signal processing method are presented.
Abstract: Manufacturing tolerancing is intended to determine
the intermediate geometrical and dimensional states of the part
during its manufacturing process. These manufacturing dimensions
also serve to satisfy not only the functional requirements given in
the definition drawing, but also the manufacturing constraints, for
example geometrical defects of the machine, vibration and the
wear of the cutting tool. In this paper, an experimental study on the
influence of the wear of the cutting tool (systematic dispersions) is
explored. This study was carried out on three stages .The first stage
allows machining without elimination of dispersions (random,
systematic) so the tolerances of manufacture according to total
dispersions. In the second stage, the results of the first stage are
filtered in such way to obtain the tolerances according to random
dispersions. Finally, from the two previous stages, the systematic
dispersions are generated. The objective of this study is to model
by the least squares method the error of manufacture based on
systematic dispersion. Finally, an approach of optimization of the
manufacturing tolerances was developed for machining on a CNC
machine tool
Abstract: Cluster analysis divides data into groups that are
meaningful, useful, or both. Analysis of biological data is creating a
new generation of epidemiologic, prognostic, diagnostic and
treatment modalities. Clustering of protein sequences is one of the
current research topics in the field of computer science. Linear
relation is valuable in rule discovery for a given data, such as if value
X goes up 1, value Y will go down 3", etc. The classical linear
regression models the linear relation of two sequences perfectly.
However, if we need to cluster a large repository of protein sequences
into groups where sequences have strong linear relationship with
each other, it is prohibitively expensive to compare sequences one by
one. In this paper, we propose a new technique named General
Regression Model Technique Clustering Algorithm (GRMTCA) to
benignly handle the problem of linear sequences clustering. GRMT
gives a measure, GR*, to tell the degree of linearity of multiple
sequences without having to compare each pair of them.
Abstract: This paper presents an experimental investigation of
transformer dielectric response and solid insulation water content.
The dielectric response was carried out on the base of Hybrid
Frequency Dielectric Spectroscopy and Polarization Current
measurements method (FDS &PC). The calculation of the water
content in paper is based on the water content in oil and the obtained
equilibrium curves. A reference measurements were performed at
equilibrium conditions for water content in oil and paper of
transformer at different stable temperatures (25, 50, 60 and 70°C) to
prepare references to evaluate the insulation behavior at the not
equilibrium conditions. Some measurements performed at the
different simulated normal working modes of transformer operation
at the same temperature where the equilibrium conditions. The
obtained results show that when transformer temperature is mach
more than the its ambient temperature, the transformer temperature
decreases immediately after disconnecting the transformer from the
network and this temperature reduction influences the transformer
insulation condition in the measuring process. In addition to the oil
temperature at the near places to the sensors, the temperature
uniformity in transformer which can be changed by a big change in
the load of transformer before the measuring time will influence the
result. The investigations have shown that the extremely influence of
the time between disconnecting the transformer and beginning the
measurements on the results. And the online monitoring for water
content in paper measurements, on the basis of the oil water content
on line monitoring and the obtained equilibrium curves. The
measurements where performed continuously and for about 50 days
without any disconnection in the prepared the adiabatic room.
Abstract: This paper discusses ways to foster cooperative learning through the integration of online communication technology. While the education experts believe constructivism produces a more positive learning experience, the educators are still facing problems in getting students to participate due to numerous reasons such as shy personality, language and cultural barriers. This paper will look into the factors that lead to lack of participations among students and how technology can be implemented to overcome these issues.
Abstract: In this paper, the deformation modes of a compact impact absorption member subjected to axial compression are investigated using finite element method and experiments. A multiple combination compact impact absorption member, referred to as a 'compress-expand member', is proposed to substitute the conventional thin-walled circular tube. This study found that the proposed compact impact absorption member has stable load increase characteristics and a wider range of high load efficiency (Pave/Pmax) than the thin-walled circular tube. Moreover, the proposed compact impact absorption member can absorb larger loads in a smaller radius than the thin-walled cylindrical tube, as it can maintain its stable deformation in increased wall thicknesses.
Abstract: Image fusion aims to enhance the perception
of a scene by combining important information captured by
different sensors. Dual-Tree Complex Wavelet (DT-CWT) has been
thouroughly investigated for image fusion, since it takes advantages
of approximate shift invariance and direction selectivity. But it can
only handle limited direction information. To allow a more flexible
directional expansion for images, we propose a novel fusion scheme,
referred to as complex contourlet transform (CCT). It successfully
incorporates directional filter banks (DFB) into DT-CWT. As a result
it efficiently deal with images containing contours and textures,
whereas it retains the property of shift invariance. Experimental
results demonstrated that the method features high quality fusion
performance and can facilitate many image processing applications.
Abstract: This paper presents an efficient emission constrained
hydrothermal scheduling algorithm that deals with nonlinear
functions such as the water discharge characteristics, thermal cost,
and transmission loss. It is then incorporated into the hydrothermal
coordination program. The program has been tested on a practical
utility system having 32 thermal and 12 hydro generating units. Test
results show that a slight increase in production cost causes a
substantial reduction in emission.
Abstract: Recent widespread use of information and
communication technology has greatly changed information security
risks that businesses and institutions encounter. Along with this
situation, in order to ensure security and have confidence in electronic
trading, it has become important for organizations to take competent
information security measures to provide international confidence that
sensitive information is secure. Against this backdrop, the approach to
information security checking has come to an important issue, which
is believed to be common to all countries. The purpose of this paper is
to introduce the new system of information security checking program
in Korea and to propose synthetic information security
countermeasures under domestic circumstances in order to protect
physical equipment, security management and technology, and the
operation of security check for securing services on ISP(Internet
Service Provider), IDC(Internet Data Center), and
e-commerce(shopping malls, etc.)
Abstract: Particulate matter (PM) in ambient air is responsible
for adverse health effects in adults and children. Relatively little is
known about the concentrations, sources and health effects of PM in
indoor air. A monitoring study was conducted in Ankara by three
campaigns in order to measure PM levels in indoor and outdoor
environments to identify and quantify associations between sources
and concentrations. Approximately 82 homes (1st campaign for 42,
2nd campaign for 12, and 3rd campaign for 28), three rooms (living
room, baby-s room and living room used as a baby-s room) and
outdoor ambient at each home were sampled with Grimm
Environmental Dust Monitoring (EDM) 107, during different
seasonal periods of 2011 and 2012. In this study, the relationship
between indoor and outdoor PM levels for particulate matter less than
10 micrometer (.m) (PM10), particulate matter less than 2.5.m
(PM2.5) and particulate matter less than 1.0.m (PM1) were
investigated. The mean concentration of PM10, PM2.5, and PM1.0 at
living room used as baby-s room is higher than living and baby-s
room (or bedroom) for three sampling campaigns. It is concluded that
the household activities and environmental conditions are very
important for PM concentrations in the indoor environments during
the sampling periods. The amount of smokers, being near a main
street and/or construction activities increased the PM concentration.
This study is based on the assessment the relationship between indoor
and outdoor PM levels and the household activities and
environmental conditions
Abstract: Pattern recognition is the research area of Artificial
Intelligence that studies the operation and design of systems that
recognize patterns in the data. Important application areas are image
analysis, character recognition, fingerprint classification, speech
analysis, DNA sequence identification, man and machine
diagnostics, person identification and industrial inspection. The
interest in improving the classification systems of data analysis is
independent from the context of applications. In fact, in many
studies it is often the case to have to recognize and to distinguish
groups of various objects, which requires the need for valid
instruments capable to perform this task. The objective of this article
is to show several methodologies of Artificial Intelligence for data
classification applied to biomedical patterns. In particular, this work
deals with the realization of a Computer-Aided Detection system
(CADe) that is able to assist the radiologist in identifying types of
mammary tumor lesions. As an additional biomedical application of
the classification systems, we present a study conducted on blood
samples which shows how these methods may help to distinguish
between carriers of Thalassemia (or Mediterranean Anaemia) and
healthy subjects.
Abstract: It is established that the instantaneous heart rate (HR) of healthy humans keeps on changing. Analysis of heart rate variability (HRV) has become a popular non invasive tool for assessing the activities of autonomic nervous system. Depressed HRV has been found in several disorders, like diabetes mellitus (DM) and coronary artery disease, characterised by autonomic nervous dysfunction. A new technique, which searches for pattern repeatability in a time series, is proposed specifically for the analysis of heart rate data. These set of indices, which are termed as pattern repeatability measure and pattern repeatability ratio are compared with approximate entropy and sample entropy. In our analysis, based on the method developed, it is observed that heart rate variability is significantly different for DM patients, particularly for patients with diabetic foot ulcer.