Abstract: Two algorithms are proposed to reduce the storage requirements for mammogram images. The input image goes through a shrinking process that converts the 16-bit images to 8-bits by using pixel-depth conversion algorithm followed by enhancement process. The performance of the algorithms is evaluated objectively and subjectively. A 50% reduction in size is obtained with no loss of significant data at the breast region.
Abstract: Inter-symbol interference if not taken care off may cause severe error at the receiver and the detection of signal becomes difficult. An adaptive equalizer employing Recursive Least Squares algorithm can be a good compensation for the ISI problem. In this paper performance of communication link in presence of Least Mean Square and Recursive Least Squares equalizer algorithm is analyzed. A Model of communication system having Quadrature amplitude modulation and Rician fading channel is implemented using MATLAB communication block set. Bit error rate and number of errors is evaluated for RLS and LMS equalizer algorithm, due to change in Signal to Noise Ratio (SNR) and fading component gain in Rician fading Channel.
Abstract: Two-dimensional (2D) bar codes were designed to
carry significantly more data with higher information density and
robustness than its 1D counterpart. Thanks to the popular
combination of cameras and mobile phones, it will naturally bring
great commercial value to use the camera phone for 2D bar code
reading. This paper addresses the problem of specific 2D bar code
design for mobile phones and introduces a low-level encoding
method of matrix codes. At the same time, we propose an efficient
scheme for 2D bar codes decoding, of which the effort is put on
solutions of the difficulties introduced by low image quality that is
very common in bar code images taken by a phone camera.
Abstract: There are few studies on eggshell of leatherback turtle
which is endangered species in Thailand. This study was focusing on
the ultrastructure and elemental composition of leatherback turtle
eggshells collected from Andaman Sea Shore, Thailand during the
nesting season using scanning electron microscope (SEM). Three
eggshell layers of leatherback turtle; the outer cuticle layer or
calcareous layer, the middle layer or middle multistrata layer and the
inner fibrous layer were recognized. The outer calcareous layer was
thick and porosity which consisted of loose nodular units of various
crystal shapes and sizes. The loose attachment between these units
resulted in numerous spaces and openings. The middle layer was
compact thick with several multistrata and contained numerous
openings connecting to both outer cuticle layer and inner fibrous
layer. The inner fibrous layer was compact and thin, and composed of
numerous reticular fibers. Energy dispersive X-ray microanalysis
detector revealed energy spectrum of X-rays character emitted from
all elements on each layer. The percentages of all elements were
found in the following order: carbon (C) > oxygen (O) > calcium
(Ca) > sulfur (S) > potassium (K) > aluminum (Al) > iodine (I) >
silicon (Si) > chlorine (Cl) > sodium (Na) > fluorine (F) >
phosphorus (P) > magnesium (Mg). Each layer consisted of high
percentage of CaCO3 (approximately 98%) implying that it was
essential for turtle embryonic development. A significant difference
was found in the percentages of Ca and Mo in the 3layers. Moreover,
transition metal, metal and toxic non-metal contaminations were
found in leatherback turtle eggshell samples. These were palladium
(Pd), molybdenum (Mo), copper (Cu), aluminum (Al), lead (Pb), and
bromine (Br). The contamination elements were seen in the outer
layers except for Mo. All elements were readily observed and
mapped using Smiling program. X-ray images which mapped the
location of all elements were showed. Calcium containing in the
eggshell appeared in high contents and was widely distributing in
clusters of the outer cuticle layer to form CaCO3 structure. Moreover,
the accumulation of Na and Cl was observed to form NaCl which was
widely distributing in 3 eggshell layers. The results from this study
would be valuable on assessing the emergent success in this
endangered species.
Abstract: In Thailand, the practice of pre-hospital Emergency
Medical Service (EMS) in each area reveals the different growth
rates and effectiveness of the practices. Those can be found as the
diverse quality and quantity. To shorten the learning curve prior to
speed-up the practices in other areas, story telling and lessons learnt
from the effective practices are valued as meaningful knowledge. To
this paper, it was to ascertain the factors, lessons learnt and best
practices that have impact as contributing to the success of prehospital
EMS system. Those were formulized as model prior to
speedup the practice in other areas. To develop the model, Malcolm
Baldrige National Quality Award (MBNQA), which is widely
recognized as a framework for organizational quality assessment and
improvement, was chosen as the discussion framework. Remarkably,
this study was based on the consideration of knowledge capture;
however it was not to complete the loop of knowledge activities.
Nevertheless, it was to highlight the recognition of knowledge
capture, which is the initiation of knowledge management.
Abstract: The bioassay-guided isolation and purification of an
ethyl acetate extract of Aspergillus terreus MC751 led to the
characterization of butyrolactone I as an antidiabetic and antioxidant.
The antidiabetic activity of butyrolactone I was evaluated by α-
glucosidase and α-amylase inhibition assays. Butyrolactone I
demonstrated significant concentration-dependent, mixed-type
inhibitory activity against yeast α-glucosidase with an IC50 of 54μM.
However, the compound exhibited less activity against rat intestinal
α-glucosidase and α-amylase. This is the first report on α-glucosidase
inhibitory activity of butyrolactone I. The antioxidative activity of
butyrolactone I was evaluated based on scavenging effects on 1,1-
diphenyl-2-picrylhydrazyl (DPPH) (IC50 =51 μM) and hydrogen
peroxide (IC50= 141 μM) radicals as well as a reducing power assay.
The results suggest that butyrolactone I is a promising antidiabetic as
well as antioxidant and should be considered for clinical trials.
Abstract: In this paper a novel algorithm is proposed that integrates the process of fuzzy hierarchy generation and rule discovery for automated discovery of Production Rules with Fuzzy Hierarchy (PRFH) in large databases.A concept of frequency matrix (Freq) introduced to summarize large database that helps in minimizing the number of database accesses, identification and removal of irrelevant attribute values and weak classes during the fuzzy hierarchy generation.Experimental results have established the effectiveness of the proposed algorithm.
Abstract: We investigated the effects of modified
preprogrammed training mode Chase Trainer from Balance Trainer
(BT3, HurLab, Tampere, Finland) on athlete who experienced
unilateral Patellofemoral Pain Syndrome (PFPS). Twenty-seven
athletes with mean age= 14.23 ±1.31 years, height = 164.89 ± 7.85
cm, weight = 56.94 ± 9.28 kg were randomly assigned to two groups:
experiment (EG; n = 14) and injured (IG; n = 13). EG performed a
series of Chase Trainer program which required them to shift their
body weight at different directions, speeds and angle of leaning twice
a week for duration of 8 weeks. The static postural control and
perceived pain level measures were taken at baseline, after 6 weeks
and 8 weeks of training. There was no significant difference in any of
tested variables between EG and IG before and after 6-week the
intervention period. However, after 8-week of training, the postural
control (eyes open) and perceived pain level of EG improved
compared to IG (p
Abstract: Existing experiences indicate that one of the most
prominent reasons that some ERP implementations fail is related to
selecting an improper ERP package. Among those important factors
resulting in inappropriate ERP selections, one is to ignore preliminary
activities that should be done before the evaluation of ERP packages.
Another factor yielding these unsuitable selections is that usually
organizations employ prolonged and costly selection processes in
such extent that sometimes the process would never be finalized
or sometimes the evaluation team might perform many key final
activities in an incomplete or inaccurate way due to exhaustion, lack
of interest or out-of-date data. In this paper, a systematic approach
that recommends some activities to be done before and after the
main selection phase is introduced for choosing an ERP package. On
the other hand, the proposed approach has utilized some ideas that
accelerates the selection process at the same time that reduces the
probability of an erroneous final selection.
Abstract: When designing information systems that deal with
large amount of domain knowledge, system designers need to consider
ambiguities of labeling termsin domain vocabulary for navigating
users in the information space. The goal of this study is to develop a
methodology for system designers to label navigation items, taking
account of ambiguities stems from synonyms or polysemes of labeling
terms. In this paper, we propose a method for concept labeling based
on mappings between domain ontology andthesaurus, and report
results of an empirical evaluation.
Abstract: With constraints on data availability and for study of power system stability it is adequate to model the synchronous generator with field circuit and one equivalent damper on q-axis known as the model 1.1. This paper presents a systematic procedure for modelling and simulation of a single-machine infinite-bus power system installed with a thyristor controlled series compensator (TCSC) where the synchronous generator is represented by model 1.1, so that impact of TCSC on power system stability can be more reasonably evaluated. The model of the example power system is developed using MATLAB/SIMULINK which can be can be used for teaching the power system stability phenomena, and also for research works especially to develop generator controllers using advanced technologies. Further, the parameters of the TCSC controller are optimized using genetic algorithm. The non-linear simulation results are presented to validate the effectiveness of the proposed approach.
Abstract: Despite the extensive use of eLearning systems, there
is no consensus on a standard framework for evaluating this kind of
quality system. Hence, there is only a minimum set of tools that can
supervise this judgment and gives information about the course
content value. This paper presents two kinds of quality set evaluation
indicators for eLearning courses based on the computational process
of three known metrics, the Euclidian, Hamming and Levenshtein
distances. The “distance" calculus is applied to standard evaluation
templates (i.e. the European Commission Programme procedures vs.
the AFNOR Z 76-001 Standard), determining a reference point in the
evaluation of the e-learning course quality vs. the optimal concept(s).
The case study, based on the results of project(s) developed in the
framework of the European Programme “Leonardo da Vinci", with
Romanian contractors, try to put into evidence the benefits of such a
method.
Abstract: Collateralized Debt Obligations are not as widely used
nowadays as they were before 2007 Subprime crisis. Nonetheless
there remains an enthralling challenge to optimize cash flows
associated with synthetic CDOs. A Gaussian-based model is used
here in which default correlation and unconditional probabilities of
default are highlighted. Then numerous simulations are performed
based on this model for different scenarios in order to evaluate the
associated cash flows given a specific number of defaults at different
periods of time. Cash flows are not solely calculated on a single
bought or sold tranche but rather on a combination of bought and
sold tranches. With some assumptions, the simplex algorithm gives
a way to find the maximum cash flow according to correlation of
defaults and maturities. The used Gaussian model is not realistic in
crisis situations. Besides present system does not handle buying or
selling a portion of a tranche but only the whole tranche. However the
work provides the investor with relevant elements on how to know
what and when to buy and sell.
Abstract: Purpose: Planning and dosimetry of different VMAT algorithms (SmartArc, Ergo++, Autobeam) is compared with IMRT for Head and Neck Cancer patients. Modelling was performed to rule out the causes of discrepancies between planned and delivered dose. Methods: Five HNC patients previously treated with IMRT were re-planned with SmartArc (SA), Ergo++ and Autobeam. Plans were compared with each other and against IMRT and evaluated using DVHs for PTVs and OARs, delivery time, monitor units (MU) and dosimetric accuracy. Modelling of control point (CP) spacing, Leaf-end Separation and MLC/Aperture shape was performed to rule out causes of discrepancies between planned and delivered doses. Additionally estimated arc delivery times, overall plan generation times and effect of CP spacing and number of arcs on plan generation times were recorded. Results: Single arc SmartArc plans (SA4d) were generally better than IMRT and double arc plans (SA2Arcs) in terms of homogeneity and target coverage. Double arc plans seemed to have a positive role in achieving improved Conformity Index (CI) and better sparing of some Organs at Risk (OARs) compared to Step and Shoot IMRT (ss-IMRT) and SA4d. Overall Ergo++ plans achieved best CI for both PTVs. Dosimetric validation of all VMAT plans without modelling was found to be lower than ss-IMRT. Total MUs required for delivery were on average 19%, 30%, 10.6% and 6.5% lower than ss-IMRT for SA4d, SA2d (Single arc with 20 Gantry Spacing), SA2Arcs and Autobeam plans respectively. Autobeam was most efficient in terms of actual treatment delivery times whereas Ergo++ plans took longest to deliver. Conclusion: Overall SA single arc plans on average achieved best target coverage and homogeneity for both PTVs. SA2Arc plans showed improved CI and some OARs sparing. Very good dosimetric results were achieved with modelling. Ergo++ plans achieved best CI. Autobeam resulted in fastest treatment delivery times.
Abstract: In the present paper, an improved initial value
numerical technique is presented to analyze the free vibration of
symmetrically laminated rectangular plate. A combination of the
initial value method (IV) and the finite differences (FD) devices is
utilized to develop the present (IVFD) technique. The achieved
technique is applied to the equation of motion of vibrating laminated
rectangular plate under various types of boundary conditions. Three
common types of laminated symmetrically cross-ply, orthotropic and
isotropic plates are analyzed here. The convergence and accuracy of
the presented Initial Value-Finite Differences (IVFD) technique have
been examined. Also, the merits and validity of improved technique
are satisfied via comparing the obtained results with those available
in literature indicating good agreements.
Abstract: In recent years asymmetric cross section aluminum
alloy stock has been finding increasing use in various industrial manufacturing areas such as general structures and automotive
components. In these areas, components are generally required to have
complex curved configuration and, as such, a bending process is required during manufacture. Undesirable deformation in bending
processes such as flattening or wrinkling can easily occur when thin-walled sections are bent. Hence, a thorough understanding of the
bending behavior of such sections is needed to prevent these undesirable deformations. In this study, the bending behavior of
asymmetric channel section was examined using finite element analysis (FEA). Typical methods of preventing undesirable
deformation, such as asymmetric laminated elastic mandrels were included in FEA model of draw bending. Additionally, axial tension
was applied to prevent wrinkling. By utilizing the FE simulations effect of restriction dies and axial tension on undesirable deformation during the process was clarified.
Abstract: This paper presents a large scale, quantitative investigation of the impact of discipline differences on the student experience of using an online learning environment (OLE). Based on a representative sample of 2526 respondents, a number of significant differences in the mean rating by broad discipline area of the importance of, and satisfaction with, a range of elements of an OLE were found. Broadly speaking, the Arts and Science and Technology discipline areas reported the lowest importance and satisfaction ratings for the OLE, while the Health and Behavioural Sciences area was the most satisfied with the OLE. A number of specific, systematic discipline differences are reported and discussed. Compared to the observed significant differences in mean importance ratings, there were fewer significant differences in mean satisfaction ratings, and those that were observed were less systematic than for importance ratings.
Abstract: Variations in the growth rate constant of the Listeria
monocytogenes bacterial species were determined at 37°C in
irradiated environments and compared to the situation of a nonirradiated
environment. The bacteria cells, contained in a suspension
made of a nutrient solution of Brain Heart Infusion, were made to
grow at different frequency (2.30e2.60 GHz) and power (0e400
mW) values, in a plug flow reactor positioned in the irradiated
environment. Then the reacting suspension was made to pass into a
cylindrical cuvette where its optical density was read every 2.5
minutes at a wavelength of 600 nm. The obtained experimental data
of optical density vs. time allowed the bacterial growth rate constant
to be derived; this was found to be slightly influenced by microwave
power, but not by microwave frequency; in particular, a minimum
value was found for powers in the 50e150 mW field.
Abstract: The V-notches are most possible case for initiation of cracks in parts. The specifications of cracks on the tip of the notch will be influenced via opening angle, tip radius and depth of V-notch. In this study, the effects of V-notch-s opening angle on stress intensity factor and T-stress of crack on the notch has been investigated. The experiment has been done in different opening angles and various crack length in mode (I) loading using Photoelasticity method. The results illustrate that while angle increases in constant crack-s length, SIF and T-stress will decrease. Beside, the effect of V-notch angle in short crack is more than long crack. These V-notch affects are negligible by increasing the length of crack, and the crack-s behavior can be considered as a single-edge crack specimen. Finally, the results have been evaluated with numerical finite element analysis and good agreement was obvious.
Abstract: A number of studies highlighted problems related to
ERP systems, yet, most of these studies focus on the problems during
the project and implementation stages but not during the postimplementation
use process. Problems encountered in the process of
using ERP would hinder the effective exploitation and the extended
and continued use of ERP systems and their value to organisations.
This paper investigates the different types of problems users
(operational, supervisory and managerial) faced in using ERP and
how 'feral system' is used as the coping mechanism. The paper
adopts a qualitative method and uses data collected from two cases
and 26 interviews, to inductively develop a casual network model of
ERP usage problem and its coping mechanism. This model classified
post ERP usage problems as data quality, system quality, interface
and infrastructure. The model is also categorised the different coping
mechanism through use of 'feral system' inclusive of feral
information system, feral data and feral use of technology.